| Age | Commit message (Collapse) | Author |
|---|
|
RTL8211E
[ Upstream commit dcabb06bf127b3e0d3fbc94a2b65dd56c2725851 ]
UniPhier LD20 and PXs3 boards have RTL8211E ethernet phy, and the phy have
the RX/TX delays of RGMII interface using pull-ups on the RXDLY and TXDLY
pins.
After the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: c73730ee4c9a ("arm64: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
The memory regions specified by /memreserve/ are passed to
early_init_dt_reserve_memory_arch() with nomap=false, so it is
not suitable for reserving memory for Trusted Firmware-A etc.
Use the more robust /reserved-memory node with the no-map property
to prevent the kernel from mapping it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
With commit d8e8fd0ebf8b ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM64 SoC DT updates for v5.1
- Add PCI Express controller nodes
* tag 'uniphier-dt64-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: sort labels in the same order as in dtsi
arm64: dts: uniphier: Add PCIe host controller and PHY nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add PCIe host controller and PHY nodes. This supports for LD20, PXs3 and
their boards.
This node defines PCIe memory, I/O, and config spaces as follows.
MEM: 20000000-2ffdffff (255MB)
I/O: 2ffe0000-2ffeffff ( 64KB)
CFG: 2fff0000-2fffffff ( 64KB)
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for LD20, PXs3 and the boards. This includes
additional efuse nodes for obtaining PHY trimming values.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add SD controller nodes for LD20 and PXs3.
LD20 does not support the UHS mode, while PXs3 supports it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add nodes of SPI controller for UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Catch up with the new binding of the Denali IP where three clocks,
"nand", "nand_x", "ecc" are required.
For UniPhier SoCs, the "nand_x" and "ecc" are tied up because they
are both 200MHz.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Olof Johansson:
"As always, a large number of DT updates. Too many to enumerate them
all, but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
set top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other
on-chip ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current
high-end mobile SoCs.
It's great to see mainline support for it. So far, you can't do
much with it, since a lot of peripherals are not yet in the DTs
but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC
upstream if the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive
entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
enabled, we are eagerly awaiting more. So far, basic drivers
such as serial, gpios, PMU and ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and
ethernet enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions
might not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
ARM: dts: aspeed: Fix hwrng register address
arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
arm64: dts: sprd: Add GPIO and GPIO keys device nodes
arm64: dts: sprd: fix typo in 'remote-endpoint'
arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
arm64: dts: fix regulator property name for wlan pcie endpoint
arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
ARM: dts: pxa3xx: fix MMC clocks
ARM: pxa: dts: add pin definitions for extended GPIOs
ARM: pxa: dts: add gpio-ranges to gpio controller
ARM: dts: ipq8074: Enable few peripherals for hk01 board
ARM: dts: ipq8074: Add pcie nodes
ARM: dts: ipq8074: Add peripheral nodes
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
ARM: dts: ipq4019: Change the max opp frequency
...
|
|
The property of the legacy mode for the eMMC PHY turned out to
be wrong. Some eMMC devices are unstable due to the set-up/hold
timing violation. Correct the delay value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add syscon-phy-mode property specifying a phandle of system controller
to each ethernet node.
In addition, LD11 SoC has a built-in ethernet PHY. When we set "internal"
to phy-mode property, this built-in PHY is available.
This patch changes phy-mode property for LD11 to "internal", as default.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add clock-names and reset-names because this node recognizes multiple
clocks and resets. ("ether", and so on, for each)
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch adds syscon property for specifying soc-glue core into
device-tree of LD11/LD20 SoC.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file. I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1]. I also dropped the parentheses to
follow the examples in that document.
[1] https://lkml.org/lkml/2017/11/25/133
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add nodes of the AVE ethernet controller for LD11 and LD20 SoCs
and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch adds audio controller, codec and simple card node of
UniPhier AIO sound system for LD11/20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The dt-bindings header was applied to the driver subsystem. I had to
wait for a merge window to use it from DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add resets properties to all nodes that have reset lines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add mmc-pwrseq-emmc node to perform standard eMMC hardware reset
procedure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The GPIO controller also acts as an interrupt controller and the
interrupt lines are connected to the AIDET block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Fix warnings like follows:
Warning (node_name_chars_strict): Character '_' not recommended in ...
Commit 8654cb8d0371 ("dtc: update warning settings for new bus and
node/property name checks") says these checks are a bit subjective,
but Rob also says to not add new W=2 warnings.
The exising warnings should be fixed in order to catch new ones
easily.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add efuse node for UniPhier LD11, LD20, and PXs3.
This efuse node is included in soc-glue.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add nodes of thermal monitor and thermal zone for UniPhier LD20 SoC.
The thermal monitor node is included in sysctrl. Since the efuse might not
have a calibrated value of thermal monitor, this patch gives the default
value for LD20.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
All registers are located within 0x400 size from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add UniPhier AIDET (ARM Interrupt Detector) nodes to support
active low interrupts.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch adds reset controller node of analog signal amplifier
core (ADAMV) for UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add NAND controller node to LD11 and LD20. Neither of them supports
the CS1 line, so pinctrl is set up for a single CS line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
To include dt-bindings headers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add nodes of watchdog timer for UniPhier LD11 and LD20 SoC.
The watchdog timer is included in sysctrl.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.
The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses. The MIT license text [2] is actually what the
current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Reserve enough space below the kernel base.
The assumed address map is:
80000000 - 80ffffff : for IPP
81000000 - 81ffffff : for ARM secure
82000000 - : for Linux
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Compiling the UniPhier DT files with W=1, DTC warns like follows:
Warning (simple_bus_reg): Node /soc/smpctrl@59800000 simple-bus unit address format error, expected "59801000"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Adjust the PHY parameters for more stable access to the eMMC device.
Set the SDCLK output delay value to 21 (including HS200/400 modes).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Since commit a89c472d8b55 ("mmc: sdhci-cadence: Update PHY delay
configuration"), PHY parameters must be specified by DT.
The hard-coded settings have been converted as follows:
- SDHCI_CDNS_PHY_DLY_SD_DEFAULT -> cdns,phy-input-delay-legacy
- SDHCI_CDNS_PHY_DLY_EMMC_SDR -> cdns,phy-input-delay-mmc-highspeed
- SDHCI_CDNS_PHY_DLY_EMMC_DDR -> cdns,phy-input-delay-mmc-ddr
The following have not been moved:
- SDHCI_CDNS_PHY_DLY_SD_HS
this is unneeded in the eMMC configuration
- SDHCI_CDNS_PHY_DLY_EMMC_LEGACY
this is never enabled by the driver as it is covered by
SDHCI_CDNS_PHY_DLY_SD_DEFAULT
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Now everything is ready to enable this pinctrl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Fix warnings reported when built with W=1:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add Cadence's eMMC controller node for LD11/LD20.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These hardware blocks are SoC-specific, so their compatible strings
should be SoC-specific as well. This change has no impact on the
actual behavior since it is controlled by the generic "simple-mfd",
"syscon" compatible strings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add a CPU clock to every CPU node and CPU OPP tables to use the
generic cpufreq driver. All the CPUs in each cluster share the
same OPP table.
Note:
clock-latency-ns (300ns) was calculated based on the CPU-gear switch
sequencer spec; it takes 12 clock cycles on the sequencer running
at 50 MHz, plus a bit additional latency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The System Control node has 0x10000 byte of registers. The current
reg size must be expanded to use the cpufreq driver because the
registers controlling CPU frequency are located at offset 0x8000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
At the first system bring-up, I chose to use spin-table because ARM
Trusted Firmware was not ready for this platform at that moment.
Actually, these SoCs are equipped with EL3 and able to provide PSCI.
Now I finished porting the ATF BL31 for the UniPhier platform, so it
is ready to migrate to PSCI enable method.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
I made a mistake bacuse the Media I/O block is not implemented in
this SoC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
* dt/irq-fix:
arm64: dts: Fix broken architected timer interrupt trigger
This resolves a non-obvious conflict between a bugfix from
v4.8 and a cleanup for the exynos7 platform.
|
|
This is a simple MFD, but add a specific compatible just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The UniPhier reset controller driver has been merged. Enable it.
Also, replace the fixed-rate clocks with the dedicated clock
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
