| Age | Commit message (Collapse) | Author |
|---|
|
Add support for audio-codec NAU88C22 present on the Apalis Evaluation
Board v1.2 carrier board.
Upstream-Status: Pending
- This change depends on audio being supported on mainline for
iMX8QM/QP, which is not working yet.
Related-to: ELB-5535
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
|
|
Add support for the new version, v1.2, of Apalis Evaluation Board with
Apalis iMX8 v1.1 QP module.
Board versions v1.0 and v1.1 are compatible with each other and should
use imx8qp-apalis-v1.1-eval.dts file dts file.
Upstream-Status: Inappropriate [other]
- Apalis iMX8 QP has no specific device tree file mainline, there the
device file for iMX8 QM is used.
Related-to: ELB-5535
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
|
|
Add support for the new version, v1.2, of Apalis Evaluation Board.
Because only imx8-apalis-eval.dtsi was available and used as the only
board configuration for board version v1.0 and v1.1, it was changed to
be the common hardware configurations for all versions v1.0,
v1.1 and v1.2. Also, two .dtsi board files were added to have the
differences by board. The .dts were organized by SoM and board version.
Board versions v1.0 and v1.1 are compatible with each other and should
use imx8qm-apalis-eval.dts file or imx8qm-apalis-v1.1-eval.dts file
depending on SoM version. Now for v1.2, organized by SoM version too, the
files are imx8qm-apalis-eval-v1.2.dts and imx8qm-apalis-v1.1-eval-v1.2.dts.
Upstream-Status: Submitted [https://lore.kernel.org/all/20240125101457.9873-3-francesco@dolcini.it/]
Related-to: ELB-5535
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Upstream-Status: Submitted [https://lore.kernel.org/all/20231020153022.57858-2-andrejs.cainikovs@gmail.com/]
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
Add USB Host and USB OTG (Client/Host switching) to the Aster carrier
board.
Upstream-Status: Pending
- No support as of now in upstream linux.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the nau8822 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is faster.
Set the MCLK at the right frequency, codec can properly use it to
generate 44.1 kHz I2S-FS.
Upstream-Status: Inappropriate [other]
This commit applies to downstream only, since there is no audio support upstream.
Fixes: 23b325adbaae ("arm64: dts: imx8mp-verdin: add device tree for dahlia")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the nau8822 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is faster.
Set the MCLK at the right frequency, codec can properly use it to
generate 44.1 kHz I2S-FS.
Upstream-Status: Submitted [https://lore.kernel.org/all/20221207102749.180485-1-francesco@dolcini.it/]
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the wm8904 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is completely distorted.
Related-to: ELB-4579
Upstream-Status: Inappropriate [other]
This commit applies to downstream only, since there is no audio support upstream.
Fixes: b6cf520e97bc ("arm64: dts: imx8mp-verdin: add device tree for dahlia")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the wm8904 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is completely distorted.
Related-to: ELB-4579
Upstream-Status: Submitted [https://lore.kernel.org/all/20221201125548.34793-1-francesco@dolcini.it/]
Fixes: Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
The Verdin iMX8M Mini System on Module does not have USB-ID signal
connected on Verdin USB_2 (usbotg2). On Verdin Development board this is
no problem, as we have connected a USB-Hub that is always connected.
However, if Verdin USB_2 is desired to be used as a single USB-Host port
the chipidea driver does not detect if a USB device is plugged into this
port, due to runtime pm shutting down the PHY.
Add the power-domain &pgc_otg2 to &usbphynop2 in order to detect
plugging events and enumerate the usb device.
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Upstream-Status: Backport [2fa24aa721ebb3a83dd2093814ba9a5dcdaa3183]
|
|
The GPIO signaling ctrl_sleep_moci is currently handled as a gpio hog.
But the gpio-hog node is made a child of the wrong gpio controller.
Move it to the node representing gpio4 so that it actually works.
Without this carrier board components jumpered to use the signal are
unconditionally switched off.
Fixes: 1d8df9c74bff ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Upstream-status: Submitted [https://lore.kernel.org/all/20220922162925.2368577-2-marcel@ziswiler.com/]
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Add device tree files for the Verdin Yavia carrier board mated with
Verdin iMX8M Mini SoM.
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
Add device tree files for the Verdin Yavia carrier board mated with
Verdin iMX8M Plus SoM.
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
On the iris-v2 board, the external battery operated RTC is now mapped to
/dev/rtc0 and because of this the clock setup works as expected.
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
Both CAN controllers on Ixora v1.1 were left disabled
for some reason, even though these are present on both
Ixora v1.1 and v1.2. Lets align this and have enabled
all existing CAN controllers on all Ixora variants.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
This adds SD card sleep state and relevant pinmux configuration
for Apalis iMX8 boards. Pins for sleep state are configured for
pull-disable, except card detect pin which is always pull-up.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
Ixora board has external resistors on LED_4_* and LED_5_*.
Pins which are driving these LEDs should have no pull.
Also, configure LED pins for input/output.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
Pull configuration should be set as pull-disabled for SD card CD# pin,
as it already has an external pull-up.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
Remove sleep state from SD card pinmux configuration.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
Ixora board v1.1 MicroSD card is 4-bit wide, same as v1.2.
This change leaves data pins 4-7 not configured, so that
these can be used for other purposes.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
This fixes Ixora pinmux configuration, which should be defined within
apalis-imx8qm block.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
Use IT temperature threshold for critical/passive trip point
on Verdin iMX8M Plus and Mini.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
|
|
This is the 5.4.193 stable release
Conflicts:
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
drivers/edac/synopsys_edac.c
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/mmc/host/sdhci.c
drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
sound/soc/codecs/msm8916-wcd-analog.c
|
|
The power domains are causing the i2c expander to be reset during suspend resume. After resume the expander state is not being restored properly. So since the reset is optional, I am removing the power domains.
Signed-off-by: Oliver Brown <oliver.brown@nxp.com>
Reviewed-by: Shenwei Wang <shenwei.wang@nxp.com>
(cherry picked from commit b928f18fdf653d70871958f561357ad98fa4aa86)
|
|
Update SPI CAN controller clock to match current hardware design.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
[ Upstream commit 0310b5aa0656a94102344f1e9ae2892e342a665d ]
The ROHM BD71847 PMIC has a 32.768 kHz clock.
Describe the PMIC clock to fix the following boot errors:
bd718xx-clk bd71847-clk.1.auto: No parent clk found
bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Based on the same fix done for imx8mm-evk as per commit
a6a355ede574 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Fixes: 3e44dd09736d ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd86d85401c2049f652293877c0f7e6e5afc3bbc ]
Amlogic SM1 devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: 3d9e76483049 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-3-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c4d636bc00dc17c63ffb2a73a0da850240e26e3 ]
Amlogic G12B devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b96d4e92709b ("arm64: dts: meson-g12b: support a311d and s922x cpu operating points")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-2-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 37cbd3c522869247ed4525b5042ff4c6a276c813 ]
A label reference without brackets is a path string, not a phandle as
intended. Add the missing brackets.
Fixes: a5002c41c383 ("arm64: dts: rockchip: add WiFi module support for Firefly-RK3399")
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220304202559.317749-1-robh@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 55927cb44db43a57699fa652e2437a91620385dc ]
After converting ahci-platform txt binding to yaml nodename is reported
as not matching the standard:
arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dt.yaml:
ahci@663f2000: $nodename:0: 'ahci@663f2000' does not match '^sata(@.*)?$'
Fix it to match binding.
Fixes: ac9aae00f0fc ("arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c953c764e505428f59ffe6afb1c73b89b5b1ac35 ]
Broadcom ns2 platform has spi-cpol and spi-cpho properties set
incorrectly. As per spi-slave-peripheral-prop.yaml, these properties are
of flag or boolean type and not integer type. Fix the values.
Fixes: d69dbd9f41a7c (arm64: dts: Add ARM PL022 SPI DT nodes for NS2)
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
CC: Ray Jui <rjui@broadcom.com>
CC: Scott Branden <sbranden@broadcom.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 17ac8af678b6da6a8f1df7da8ebf2c5198741827 ]
Correct the TCS config by updating the number of TCSes for each type.
Cc: devicetree@vger.kernel.org
Fixes: d8cf9372b654 ("arm64: dts: qcom: sm8150: Add apps shared nodes")
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1641749107-31979-2-git-send-email-quic_mkshah@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Add SD1 sleep pinctrl to avoid backfeeding during sleep.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add SD1 sleep pinctrl to avoid backfeeding during sleep.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add a note about us using discrete external on-module resistors
pulling-up to the on-module +V3.3_1.8_SD (LDO5) rail and explicitly
disabling the internal pull-ups due to ERR050080 [1]:
IO: Degradation of internal IO pullup/pulldown current capability for
IO’s continuously driven in a 3.3V operating mode
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MM_0N87W
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
[ Upstream commit 268a491aebc25e6dc7c618903b09ac3a2e8af530 ]
The DWC2 USB controller on the Agilex platform does not support clock
gating, so use the chip specific "intel,socfpga-agilex-hsotg"
compatible.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e8a8b5955a000cc655f7e368670518cbb77fe58 ]
The binding specifies the clock order to "cec", "grf", "vpll". Reorder
the clocks accordingly.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220126145549.617165-19-s.hauer@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 62966cbdda8a92f82d966a45aa671e788b2006f7 ]
There are signal integrity issues running the eMMC at 200MHz on Puma
RK3399-Q7.
Similar to the work-around found for RK3399 Gru boards, lowering the
frequency to 100MHz made the eMMC much more stable, so let's lower the
frequency to 100MHz.
It might be possible to run at 150MHz as on RK3399 Gru boards but only
100MHz was extensively tested.
Cc: Quentin Schulz <foss+kernel@0leil.net>
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220119134948.1444965-1-quentin.schulz@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a1cc1697bb56cdf880ad4d17b79a39ef2c294bc9 upstream.
Legacy and old PCI I/O based cards do not support 32-bit I/O addressing.
Since commit 64f160e19e92 ("PCI: aardvark: Configure PCIe resources from
'ranges' DT property") kernel can set different PCIe address on CPU and
different on the bus for the one A37xx address mapping without any firmware
support in case the bus address does not conflict with other A37xx mapping.
So remap I/O space to the bus address 0x0 to enable support for old legacy
I/O port based cards which have hardcoded I/O ports in low address space.
Note that DDR on A37xx is mapped to bus address 0x0. And mapping of I/O
space can be set to address 0x0 too because MEM space and I/O space are
separate and so do not conflict.
Remapping IO space on Turris Mox to different address is not possible to
due bootloader bug.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 76f6386b25cc ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700")
Cc: stable@vger.kernel.org # 64f160e19e92 ("PCI: aardvark: Configure PCIe resources from 'ranges' DT property")
Cc: stable@vger.kernel.org # 514ef1e62d65 ("arm64: dts: marvell: armada-37xx: Extend PCIe MEM space")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a0e897d1b36793fe0ab899f2fe93dff25c82f418 ]
U-Boot uses ethernet* aliases for setting MAC addresses. Therefore define
also alias for ethernet0.
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Fix Lontium LT8912 based HDMI display adapter which requires its reset
pin being pulled-up as active-low and its hot-plug detect pulled-down
as active-high.
Fixes: 128d8860d36c ("arm64: dts: imx8mm-verdin: Update IOMUX configuration")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add and fill-in gpio-line-names property to gpio nodes.
Note that this represents re-designed V1.1 modules.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
commit b5fbaf7d779f5f02b7f75b080e7707222573be2a upstream.
Commit b18c6c3c7768 ("ASoC: rockchip: cdn-dp sound output use spdif")
switched the platform to SPDIF, but we didn't fix up the device tree.
Drop the pinctrl settings, because the 'spdif_bus' pins are either:
* unused (on kevin, bob), so the settings is ~harmless
* used by a different function (on scarlet), which causes probe
failures (!!)
Fixes: b18c6c3c7768 ("ASoC: rockchip: cdn-dp sound output use spdif")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220114150129.v2.1.I46f64b00508d9dff34abe1c3e8d2defdab4ea1e5@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Likely, the extcon-usb-gpio should not be definied within the i2c4 node
but rather the SoC one.
This fixes the following device tree compiler warning:
arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi:581.28-586.4: Warning
(i2c_bus_reg): /soc@0/bus@30800000/i2c@30a50000/usb_1_id: missing or
empty reg property
And fixes the following error on boot:
[ 1.858518] i2c i2c-3: of_i2c: invalid reg on /soc@0/bus@30800000/
i2c@30a50000/usb_1_id
[ 1.866544] i2c i2c-3: Failed to create I2C device for /soc@0/bus@
30800000/i2c@30a50000/usb_1_id
Fixes: bfe277fce128 ("arm64: dts: imx8mp-verdin: move USB_1 extcon node")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Given that the USB OTG ID pin is defined in the SOM schematics,
it should be part of the SOM device tree, not the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
The PCB of the hardware version V1.1 has a footprint for an optional
on-module I2C temperature sensor.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
The PCB of the hardware version V1.1 uses the UART4 (ECSPI2 pins) for
the Bluetooth UART, therefore move it to the Wi-Fi module device tree.
Move regular UART4 usage to non-WiFi only.
While at it also split Bluetooth specific pin from pinctrl_wifi_ctrl
into separate pinctrl_bluetooth_ctrl as that might be needed to run the
proprietary driver stack.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
The PCB of the hardware version V1.1 has the USB ID pin issue fixed.
Move USB_1_ID (pin 161) from USB1_ID to SD1_RESET_B. Support USB
device/host switching using the ID pin as an extcon GPIO.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
The PCB of the hardware version V1.1 has SODIMM pin 187 (USB_2_OC#)
swapped with 91 (CSI_1_MCLK).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
