| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Renesas ARM based SoC fixes for v3.13
* r8a7790 (R-Car H1) SoC
- Correct GPIO resources in DT.
This problem has been present since GPIOs were added to the r8a7790 SoC
by f98e10c88aa95bf7 ("ARM: shmobile: r8a7790: Add GPIO controller
devices to device tree") in v3.12-rc1.
* irqchip renesas-intc-irqpin
- Correct register bitfield shift calculation
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e3b9657 ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1
* Lager board
- Do not build the phy fixup unless CONFIG_PHYLIB is enabled
This problem was introduced by 48c8b96f21817aad
* tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Fix balloon driver for auto-translate guests (PVHVM, ARM) to not use
scratch pages.
- Fix block API header for ARM32 and ARM64 to have proper layout
- On ARM when mapping guests, stick on PTE_SPECIAL
- When using SWIOTLB under ARM, don't call swiotlb functions twice
- When unmapping guests memory and if we fail, don't return pages which
failed to be unmapped.
- Grant driver was using the wrong address on ARM.
* tag 'stable/for-linus-3.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Seperate the auto-translate logic properly (v2)
xen/block: Correctly define structures in public headers on ARM32 and ARM64
arm: xen: foreign mapping PTEs are special.
xen/arm64: do not call the swiotlb functions twice
xen: privcmd: do not return pages which we have failed to unmap
XEN: Grant table address, xen_hvm_resume_frames, is a phys_addr not a pfn
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
I accidentally removed some mux code for omap4 that I thought was
dead code as omap4 has been booting with device tree only since
v3.10. Turns out I also removed some display related mux code,
so let's revert that except for the dead code parts.
* tag 'omap-for-v3.13/display-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (439 commits)
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
+Linux 3.13-rc4
|
|
The r8a7790.dtsi file has four sdhi nodes which the first two have the wrong
resource size for their register block. This causes the sh_modbile_sdhi driver
to fail to communicate with card at-all.
Change sdhi{0,1} node size from 0x100 to 0x200 to correct these nodes
as per Kuninori Morimoto's response to the original patch where all four
nodes where changed. sdhi{2,3} are the correct size.
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa41853272a ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: William Towle <william.towle@codethink.co.uk>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
4dcfa60071b3d23f0181f27d8519f12e37cefbb9
(ARM: DMA-API: better handing of DMA masks for coherent allocations)
exchanged DMA mask check method.
Below warning will appear without this patch
asoc-simple-card asoc-simple-card.0: \
Coherent DMA mask 0xffffffffffffffff is larger than dma_addr_t allows
asoc-simple-card asoc-simple-card.0: \
Driver did not use or check the return value from dma_set_coherent_mask()?
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit 22ceeee16eb8f0d04de3ef43a5174fb30ec18af9 ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator to board code with a consumer supply
entry for the backlight device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit ad11cb9a5cf96346f1240995c672cdbb5501785c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit e30b06f4d5f000c31a7747a7e7ada78a5fd419a1 (ARM: OMAP2+: Remove
legacy mux code for display.c) removed non-DT DSI and HDMI pinmuxing.
However, DSI pinmuxing is still needed, and removing that caused DSI
displays not to work.
This reverts the DSI parts of the commit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit
4178bac ARM: call of_clk_init from default time_init handler
added implicit call to of_clk_init() from default time_init callback,
but it did not change platforms calling it from other callbacks, despite
of not having custom time_init callbacks. This caused double clock
initialization on such platforms, leading to boot failures. An example
of such platform is mach-s3c64xx.
This patch fixes boot failure on s3c64xx by dropping custom init_irq
callback, which had a call to of_clk_init() and moving system reset
initialization to init_machine callback. This allows us to have
clocks initialized properly without a need to have custom init_time or
init_irq callbacks.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM fixes from Russell King:
"This resolves some further issues with the dma mask changes on ARM
which have been found by TI and others, and also some corner cases
with the updates to the virtual to physical address translations.
Konstantin also found some problems with the unwinder, which now
performs tighter verification that the stack is valid while unwinding"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix asm/memory.h build error
ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
ARM: 7913/1: fix framepointer check in unwind_frame
ARM: 7912/1: check stack pointer in get_wchan
ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
ARM: 7908/1: mm: Fix the arm_dma_limit calculation
ARM: another fix for the DMA mapping checks
|
|
Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:
In file included from arch/arm/include/asm/page.h:163:0,
from include/linux/mm_types.h:16,
from include/linux/sched.h:24,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)
Fixes: ca5a45c06cd4 ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions")
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The Allwinner A31 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A31 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A20 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org #3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add a missing break to the switch in tegra_init_fuse() which determines
which SoC the code is running on. This prevents the Tegra30+ fuse
handling code from running on Tegra20.
Fixes: 3bd1ae57f7bb ("ARM: tegra: add fuses as device randomness")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
If SDRAM is not reset, it causes memory bus congestion and
the device hangs. We put SDRAM in selfresh mode before watchdog
reset, removing potential freezes.
Without this patch PXA270-based ICP DAS LP-8x4x hangs after up to 40
reboots. With this patch it has successfully rebooted 500 times.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When converting from tosa-keyboard driver to matrix keyboard, tosa keys
received extra 1 column shift. Replace that with correct values to make
keyboard work again.
Fixes: f69a6548c9d5 ('[ARM] pxa/tosa: make use of the matrix keypad driver')
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
These mappings are in fact special and require special handling in privcmd,
which already exists. Failure to mark the PTE as special on arm64 causes all
sorts of bad PTE fun. e.g.
e.g.:
BUG: Bad page map in process xl pte:e0004077b33f53 pmd:4079575003
page:ffffffbce1a2f328 count:1 mapcount:-1 mapping: (null) index:0x0
page flags: 0x4000000000000014(referenced|dirty)
addr:0000007fb5259000 vm_flags:040644fa anon_vma: (null) mapping:ffffffc03a6fda58 index:0
vma->vm_ops->fault: privcmd_fault+0x0/0x38
vma->vm_file->f_op->mmap: privcmd_mmap+0x0/0x2c
CPU: 0 PID: 2657 Comm: xl Not tainted 3.12.0+ #102
Call trace:
[<ffffffc0000880f8>] dump_backtrace+0x0/0x12c
[<ffffffc000088238>] show_stack+0x14/0x1c
[<ffffffc0004b67e0>] dump_stack+0x70/0x90
[<ffffffc000125690>] print_bad_pte+0x12c/0x1bc
[<ffffffc0001268f4>] unmap_single_vma+0x4cc/0x700
[<ffffffc0001273b4>] unmap_vmas+0x68/0xb4
[<ffffffc00012c050>] unmap_region+0xcc/0x1d4
[<ffffffc00012df20>] do_munmap+0x218/0x314
[<ffffffc00012e060>] vm_munmap+0x44/0x64
[<ffffffc00012ed78>] SyS_munmap+0x24/0x34
Where unmap_single_vma contains inlined -> unmap_page_range -> zap_pud_range
-> zap_pmd_range -> zap_pte_range -> print_bad_pte.
Or:
BUG: Bad page state in process xl pfn:4077b4d
page:ffffffbce1a2f8d8 count:0 mapcount:-1 mapping: (null) index:0x0
page flags: 0x4000000000000014(referenced|dirty)
Modules linked in:
CPU: 0 PID: 2657 Comm: xl Tainted: G B 3.12.0+ #102
Call trace:
[<ffffffc0000880f8>] dump_backtrace+0x0/0x12c
[<ffffffc000088238>] show_stack+0x14/0x1c
[<ffffffc0004b67e0>] dump_stack+0x70/0x90
[<ffffffc00010f798>] bad_page+0xc4/0x110
[<ffffffc00010f8b4>] free_pages_prepare+0xd0/0xd8
[<ffffffc000110e94>] free_hot_cold_page+0x28/0x178
[<ffffffc000111460>] free_hot_cold_page_list+0x38/0x60
[<ffffffc000114cf0>] release_pages+0x190/0x1dc
[<ffffffc00012c0e0>] unmap_region+0x15c/0x1d4
[<ffffffc00012df20>] do_munmap+0x218/0x314
[<ffffffc00012e060>] vm_munmap+0x44/0x64
[<ffffffc00012ed78>] SyS_munmap+0x24/0x34
x86 already gets this correct. 32-bit arm gets away with this because there is
not PTE_SPECIAL bit in the PTE there and the vm_normal_page fallback path does
the right thing.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
Due to the cross dependencies between hwmod for automanaged device
information for OMAP and dts node definitions, we can run into scenarios
where the dts node is defined, however it's hwmod entry is yet to be
added. In these cases:
a) omap_device does not register a pm_domain (since it cannot find
hwmod entry).
b) driver does not know about (a), does a pm_runtime_get_sync which
never fails
c) It then tries to do some operation on the device (such as read the
revision register (as part of probe) without clock or adequate OMAP
generic PM operation performed for enabling the module.
This causes a crash such as that reported in:
https://bugzilla.kernel.org/show_bug.cgi?id=66441
When 'ti,hwmod' is provided in dt node, it is expected that the device
will not function without the OMAP's power automanagement. Hence, when
we hit a fail condition (due to hwmod entries not present or other
similar scenario), fail at pm_domain level due to lack of data, provide
enough information for it to be fixed, however, it allows for the driver
to take appropriate measures to prevent crash.
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
ARM: OMAP2+: hwmod code/data: fixes for v3.13-rc
Fix a few hwmod code problems involving recovery with bad data and bad
IP block OCP reset handling. Also, fix the hwmod data to enable IP
block OCP reset for the OMAP USBHOST devices on OMAP3+.
Basic build, boot, and PM tests are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_a_v3.13-rc/20131209030611/
* tag 'for-v3.13-rc/hwmod-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix usage of invalid iclk / oclk when clock node is not present
ARM: OMAP3: hwmod data: Don't prevent RESET of USB Host module
ARM: OMAP2+: hwmod: Fix SOFTRESET logic
ARM: OMAP4+: hwmod data: Don't prevent RESET of USB Host module
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
A rather big fix for a regression where we have dropped omap4 hwmod
data earlier but are not initializing it from device tree. In addition
to this fix we eventually also be fix the issues in the .dts files
and drivers, but that's too intrusive for the -rc cycle and must be
done later on.
Also a fix for a regression where we now are wrongly trying to initialize
devices on secure omaps like n900 and n9* when booted using device tree.
We need to set aes, sham and timer12 to disabled mode for secure
devices as they are claimed by the firmware running in the secure mode.
And two more legacy booting vs device tree based booting fixes for
am3517 that I did not notice earlier until Nishant Menon reported
these to me few days ago. With these we're good to go having v3.13
working both for legacy booting and device tree based booting, and we
can then go ahed and drop the legacy booting for mach-omap2 for v3.14.
* tag 'omap-for-v3.13/yet-more-dt-regressions-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (494 commits)
ARM: dts: Fix booting for secure omaps
ARM: OMAP2+: Fix the machine entry for am3517
ARM: dts: Fix missing entries for am3517
ARM: OMAP2+: Fix overwriting hwmod data with data from device tree
+Linux 3.13-rc3
|
|
The __do_cache_op function operates with a 'chunk' size of one page
but fails to limit the size of the final chunk so as to not exceed
the specified memory region. Fix this.
Cc: <stable@vger.kernel.org>
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch fixes corner case when (fp + 4) overflows unsigned long,
for example: fp = 0xFFFFFFFF -> fp + 4 == 3.
Cc: <stable@vger.kernel.org>
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
get_wchan() is lockless. Task may wakeup at any time and change its own stack,
thus each next stack frame may be overwritten and filled with random stuff.
/proc/$pid/stack interface had been disabled for non-current tasks, see [1]
But 'wchan' still allows to trigger stack frame unwinding on volatile stack.
This patch fixes oops in unwind_frame() by adding stack pointer validation on
each step (as x86 code do), unwind_frame() already checks frame pointer.
Also I've found another report of this oops on stackoverflow (irony).
Link: http://www.spinics.net/lists/arm-kernel/msg110589.html [1]
Link: http://stackoverflow.com/questions/18479894/unwind-frame-cause-a-kernel-paging-error
Cc: <stable@vger.kernel.org>
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
To get updated __pv_phys_offset, setup_dma_zone() needs to be
called after early_paging_init().
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Current code is using PHYS_OFFSET to calculate the arm_dma_limit which
will lead to wrong calculations in cases where PHYS_OFFSET is updated
runtime.
So fix the code by using __pv_phys_offset instead of PHYS_OFFSET.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Peter reports that OMAP audio broke with the recent fix for these
checks, caused by OMAP audio using a 64-bit DMA mask. We should
allow 64-bit DMA masks even with 32-bit dma_addr_t if we can be sure
the amount of RAM we have won't allow the 32-bit dma_addr_t to
overflow. Unfortunately, the checks to detect overflow were not
correct.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
present
commit dc75925d(OMAP: hwmod: Fix the missing braces) introduced
missing braces, however, we just set return result if clk_get fail
and we populate the error pointer in clk pointer and pass it along to
clk_prepare. This is wrong. The intent seems to be retry remaining
clocks if they are available and warn the ones we cant find clks for.
With the current logic, we see the following crash:
omap_hwmod: l3_main: cannot clk_get interface_clk emac_ick
Unable to handle kernel NULL pointer dereference at virtual address 00000032
pgd = c0004000
[00000032] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc1-00044-gcc9fd5a-dirty #19
task: ce0c3440 ti: ce0c4000 task.ti: ce0c4000
PC is at __clk_prepare+0x10/0x74
LR is at clk_prepare+0x14/0x24
<snip>
[<c044d59c>] (__clk_prepare+0x10/0x74) from [<c044d9b0>] (clk_prepare+0x14/0x24)
[<c044d9b0>] (clk_prepare+0x14/0x24) from [<c077d8c4>] (_init+0x24c/0x3bc)
[<c077d8c4>] (_init+0x24c/0x3bc) from [<c0027328>] (omap_hwmod_for_each+0x34/0x5c)
[<c0027328>] (omap_hwmod_for_each+0x34/0x5c) from [<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40)
[<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40) from [<c0008928>] (do_one_initcall+0x38/0x168)
[<c0008928>] (do_one_initcall+0x38/0x168) from [<c0771be8>] (kernel_init_freeable+0xfc/0x1cc)
[<c0771be8>] (kernel_init_freeable+0xfc/0x1cc) from [<c0521064>] (kernel_init+0x8/0x110)
[<c0521064>] (kernel_init+0x8/0x110) from [<c000e568>] (ret_from_fork+0x14/0x2c)
Code: e92d4038 e2504000 01a05004 0a000005 (e5943034)
So, just warn and continue instead of proceeding and crashing, with
missing clock nodes/bad data, we will eventually fail, however we
should now have enough information to identify the culprit.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Fixes: de231388cb80 ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
In _ocp_softreset(), after _set_softreset() + write_sysconfig(),
the hwmod's sysc_cache will always contain SOFTRESET bit set
so all further writes to sysconfig using this cache will initiate
a repeated SOFTRESET e.g. enable_sysc(). This is true for OMAP3 like
platforms that have RESET_DONE status in the SYSSTATUS register and
so the the SOFTRESET bit in SYSCONFIG is not automatically cleared.
It is not a problem for OMAP4 like platforms that indicate RESET
completion by clearing the SOFTRESET bit in the SYSCONFIG register.
This repeated SOFTRESET is undesired and was the root cause of
USB host issues on OMAP3 platforms when hwmod was allowed to do the
SOFTRESET for the USB Host module.
To fix this we clear the SOFTRESET bit and update the sysconfig
register + sysc_cache using write_sysconfig().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
[paul@pwsan.com: renamed _clr_softreset() to _clear_softreset()]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Without this, the USB devices are sometimes not detected on OMAP4 Panda
with u-boot v2013.10.
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Acked-by: Benoît Cousson <bcousson@baylibre.com>
Fixes: af88fa9aa77c ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit 7ce93f3 (ARM: OMAP2+: Fix more missing data for omap3.dtsi file)
fixed missing device tree data for omaps, but did not account for some of the
hardware modules being inaccessible for secure omaps. This causes the
following error on secure omaps:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0c5048
SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.13.0-rc2+ #446
task: ce057b40 ti: ce058000 task.ti: ce058000
PC is at omap_aes_dma_stop+0x24/0x3c
LR is at omap_aes_probe+0x1cc/0x584
psr: 60000113
sp : ce059e20 ip : ce0b4ee0 fp : 00000000
r10: c0573ae8 r9 : c0749508 r8 : 00000000
r7 : ce0b4e00 r6 : 00000000 r5 : ce0b4e10 r4 : ce274890
r3 : fa0c5048 r2 : 00000048 r1 : 0000002c r0 : ce274890
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 80004019 DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xce058248)
Stack: (0xce059e20 to 0xce05a000)
9e20: c0749508 0000a1ff 00000000 c016cd8c c06b5a06 ce2a45f0 ce2a4570 ce0b5fb0
9e40: 00000000 480c5000 480c504f c0abe4e4 00000200 00000000 00000000 00000000
9e60: ce0b4e10 ce0b4e10 c082da3c c082da3c c02b8c70 c077c610 c0749508 00000000
9e80: 00000000 c02b9e7c c02b9e64 ce0b4e10 00000000 c02b8b20 ce0b4e10 ce0b4e44
9ea0: c082da3c c02b8cd8 00000000 ce059eb8 c082da3c c02b7408 ce079edc ce0b1a34
9ec0: c082da3c c082da3c ce2a0280 00000000 c08158d8 c02b8358 c0663405 c0663405
9ee0: 00000073 c082da3c c079e4e8 c07ab3bc c0844340 c02b9334 00000000 00000006
9f00: c079e4e8 c0008920 c067f6bf c0ac7c6b 00000000 c0712e28 00000000 00000000
9f20: c0712e38 ce059f38 00000093 c0ac7c82 00000000 c0058994 00000000 c07130e8
9f40: c07127b8 00000093 00000006 00000006 00000001 00000006 00000006 c079e4e8
9f60: c07ab3bc c0844340 00000093 c0749508 c079e4f4 c0749c64 00000006 00000006
9f80: c0749508 00000000 00000000 c0517e2c 00000000 00000000 00000000 00000000
9fa0: 00000000 c0517e34 00000000 c000dfb8 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
(omap_aes_probe+0x1cc/0x584)
(platform_drv_probe+0x18/0x48)
(driver_probe_device+0xb0/0x200)
(__driver_attach+0x68/0x8c)
(bus_for_each_dev+0x50/0x88)
(bus_add_driver+0xcc/0x1c8)
(driver_register+0x9c/0xe0)
(do_one_initcall+0x98/0x140)
(kernel_init_freeable+0x16c/0x23c)
(kernel_init+0x8/0x100)
(ret_from_fork+0x14/0x3c)
Code: e1811002 e5932020 e590300c e0833002 (e593c000)
Let's fix the issue by adding omap34xx-hs.dtsi and omap36xx-hs.dtsi and make
n900, n9 and n950 to use them. This way we have the aes, sham and timer12
disabled for secure devices the same way legacy booting does based on the
omap34xx_gp_hwmod_ocp_ifs and omap36xx_gp_hwmod_ocp_ifs arrays in
omap_hwmod_3xxx_data.c.
Reported-by: Sebastian Reichel <sre@debian.org>
Acked-By: Sebastian Reichel <sre@debian.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The am3517 is wrongly booting as omap3 which means that the am3517
specific devices like Ethernet won't work when booted with device
tree. Now with the new devices defined in am3517.dtsi, let's use
that instead of the omap3.dtsi, and add a separate machine entry
for am3517 so am3517-evm can use it.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated comments and fixed build without omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On am3517 there are some extra devices compared to omap3.dtsi that
we currently have not defined. Let's fix that by adding am3517.dtsi
file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We have some device tree properties where the ti,hwmod have multiple
values:
am33xx.dtsi: ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
am4372.dtsi: ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
dra7.dtsi: ti,hwmods = "l3_main_1", "l3_main_2";
omap3.dtsi: ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
omap3.dtsi: ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
omap4.dtsi: ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
omap5.dtsi: ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
That's not correct way of doing things in this case because these are
separate devices with their own address space, interrupts, SYSCONFIG
registers and can set their PM states independently.
So they should all be fixed up to be separate devices in the .dts files.
We also have the related data removed for at least omap4 in commit
3b9b10151c68 (ARM: OMAP4: hwmod data: Clean up the data file), so
that data is wrongly initialized as null data.
So we need to fix two bugs:
1. We are only checking the first entry of the ti,hwmods property
This means that we're only initializing the first hwmods entry
instead of the ones listed in the ti,hwmods property.
2. We are only checking the child nodes, not the nodes themselves
This means that anything listed at OCP level is currently just
ignored and unitialized and at least the omap4 case, with the
legacy data missing from the hwmod.
Fix both of the issues by using an index to the ti,hwmods property
and changing the hwmod lookup function to also check the current node
for ti,hwmods property instead of just the children.
While at it, let's also add some warnings for the bad data so it's
easier to fix.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
From Sekhar Nori:
This pull request includes a patch
to align platform code to driver's
usage of platform_get_resource_byname()
This is needed to start successfully probing
audio again. The regression was introduced
in v3.13 merge window.
* tag 'davinci-fixes-for-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: Fix McASP mem resource names
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The ASoC McASP driver looks for the mem resources by name
"mpu" and "dat" regions.
Change/add the needed name for the mem resources so the driver can pick the
correct resource.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
From Sekhar Nori:
This pull request contains a fixe for broken unbanked
GPIO IRQ support and a fix for some random memory
corruption. The bugs were introduced during v3.13
merge window.
* tag 'davinci-fixes-for-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix number of resources passed to davinci_gpio_register()
gpio: davinci: fix check for unbanked gpio
|
|
Graceful reboot and poweroff via IPMI commands to the management
processor don't work. Power and reset keys are events from the
management processor which are generated via IPC messages. Passing
the keys to userspace does not work as neither acpid nor a desktop
environment are present.
This adds a notifier handler for the IPC messages so the kernel can
handle the key events directly and IPMI graceful shutdown will work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from
board files to DT. Tony thinks this was the last major set of
fixes, with maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed
PCIe hardware, i.e. incorrect number of busses on some SoCs, etc.
The line delta adds up due to various ranges moving around when
this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in
my test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91,
a couple of reverts for ux500, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
arm: socfpga: Enable ARM_TWD for socfpga
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
ARM: multi_v7_defconfig: enable network for BeagleBone Black
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
- timekeeping: Cure a subtle drift issue on GENERIC_TIME_VSYSCALL_OLD
- nohz: Make CONFIG_NO_HZ=n and nohz=off command line option behave the
same way. Fixes a long standing load accounting wreckage.
- clocksource/ARM: Kconfig update to avoid ARM=n wreckage
- clocksource/ARM: Fixlets for the AT91 and SH clocksource/clockevents
- Trivial documentation update and kzalloc conversion from akpms pile
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix another inconsistency between CONFIG_NO_HZ=n and nohz=off
time: Fix 1ns/tick drift w/ GENERIC_TIME_VSYSCALL_OLD
clocksource: arm_arch_timer: Hide eventstream Kconfig on non-ARM
clocksource: sh_tmu: Add clk_prepare/unprepare support
clocksource: sh_tmu: Release clock when sh_tmu_register() fails
clocksource: sh_mtu2: Add clk_prepare/unprepare support
clocksource: sh_mtu2: Release clock when sh_mtu2_register() fails
ARM: at91: rm9200: switch back to clockevents_config_and_register
tick: Document tick_do_timer_cpu
timer: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
NOHZ: Check for nohz active instead of nohz enabled
|
|
From: Eric Trudeau <etrudeau@broadcom.com>
xen_hvm_resume_frames stores the physical address of the grant table.
englighten.c was incorrectly setting it as if it was a page frame number.
This caused the table to be mapped into the guest at an unexpected physical
address.
Additionally, a warning is improved to include the grant table address which
failed in xen_remap.
Signed-off-by: Eric Trudeau <etrudeau@broadcom.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
Some of the clocks that were designated gate-clk do not have a gate, so
change those clocks to be of periph-clk type.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Update Kconfig to enable TWD.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enable MMC/SD on the Broadcom mobile platforms, and increase the block
minors from the default 8 to 16 (since the Broadcom board by default
has root on the 8th partition).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org # v3.12
|
|
This enables a few more options on the sunxi defconfigs such that I can
use nfsroot to boot them (there is no local storage support yet). It
also enables PRINTK_TIME and tmpfs since it's a common distro requirement.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
|
|
BeagleBone Black uses the TI CPSW ethernet controller, enable it in the
multi_v7_defconfig for testing coverage purposes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v3.12
|
|
From Nicolas Ferre:
AT91: second round of fixes for 3.13
- reduce IP frequency for I2C on sama5d3
- missing aliases directive for USART3 on 9x5 family
- a PM symbol is missing if !CONFIG_PM
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
|
|
fixes
From Jason Cooper, mvebu DT fixes for v3.13:
- mvebu
- PCIe fixes now that we have test devices with more ports.
- fix access to coherency registers
* tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: re-enable PCIe on Armada 370 DB
ARM: mvebu: use the virtual CPU registers to access coherency registers
ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260
ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named
"vdd33a" and "vddvario". Currently the shared DTS file provides
"vmmc" and "vmmc_aux", and the supply lookup will fail:
smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree
smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree
smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
Fix it!
Looks like commmit 6b2978ac40e4 (ARM: dts: Shared file for omap GPMC
connected smsc911x) made the problem more visible by moving the smc911x
configuration from the omap3-igep0020.dts file to the generic file.
But it seems we've had this problem since commit d72b4415011e
(ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support).
Tested on OMAP3 Overo platform.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[tony@atomide.com: updated comments for the commits causing the problem]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
