| Age | Commit message (Collapse) | Author |
|---|
|
commit 9e25ebfe56ece7541cd10a20d715cbdd148a2e06 upstream.
The pmd containing memblock_limit is cleared by prepare_page_table()
which creates the opportunity for early_alloc() to allocate unmapped
memory if memblock_limit is not pmd aligned causing a boot-time hang.
Commit 965278dcb8ab ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
attempted to resolve this problem, but there is a path through the
adjust_lowmem_bounds() routine where if all memory regions start and
end on pmd-aligned addresses the memblock_limit will be set to
arm_lowmem_limit.
Since arm_lowmem_limit can be affected by the vmalloc early parameter,
the value of arm_lowmem_limit may not be pmd-aligned. This commit
corrects this oversight such that memblock_limit is always rounded
down to pmd-alignment.
Fixes: 965278dcb8ab ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06e1a5cc570703796ff1bd3a712e8e3b15c6bb0d upstream.
The manufacturing information is stored in the EEPROM. This chip
is an AT24C64 not not (nor has it ever been) 24C02. This patch will
correctly address the EEPROM to read the entire contents and not just
256 bytes (of 0xff).
Fixes: 5e3447a29a38 ("ARM: dts: LogicPD Torpedo: Add AT24 EEPROM Support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04abaf07f6d5cdf22b7a478a86e706dfeeeef960 upstream.
Starting from commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind") pm_runtime core now changes
device runtime_status back to after RPM_SUSPENDED after a probe defer.
Certain OMAP devices make use of "ti,no-idle-on-init" flag which causes
omap_device_enable to be called during the BUS_NOTIFY_ADD_DEVICE event
during probe, along with pm_runtime_set_active.
This call to pm_runtime_set_active typically will prevent a call to
pm_runtime_get in a driver probe function from re-enabling the
omap_device. However, in the case of a probe defer that happens before
the driver probe function is able to run, such as a missing pinctrl
states defer, pm_runtime_reinit will set the device as RPM_SUSPENDED and
then once driver probe is actually able to run, pm_runtime_get will see
the device as suspended and call through to the omap_device layer,
attempting to enable the already enabled omap_device and causing errors
like this:
omap-gpmc 50000000.gpmc: omap_device: omap_device_enable() called from
invalid state 1
omap-gpmc 50000000.gpmc: use pm_runtime_put_sync_suspend() in driver?
We can avoid this error by making sure the pm_runtime status of a device
matches the omap_device state before a probe attempt. By extending the
omap_device bus notifier to act on the BUS_NOTIFY_BIND_DRIVER event we
can check if a device is enabled in omap_device but with a pm_runtime
status of RPM_SUSPENDED and once again mark the device as RPM_ACTIVE to
avoid a second incorrect call to omap_device_enable.
Fixes: 5de85b9d57ab ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1be7107fbe18eed3e319a6c3e83c78254b693acb upstream.
Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.
This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.
Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.
One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications. For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).
Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.
Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Original-patch-by: Oleg Nesterov <oleg@redhat.com>
Original-patch-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[wt: backport to 4.11: adjust context]
[wt: backport to 4.9: adjust context ; kernel doc was not in admin-guide]
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5aff1d245e8cc1ab5c4517d916edaed9e3f7f973 ]
The symbols can no longer be used as loadable modules, leading to a harmless Kconfig
warning:
arch/arm/configs/imote2_defconfig:60:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/arm/configs/imote2_defconfig:59:warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP
arch/arm/configs/ezx_defconfig:68:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/arm/configs/ezx_defconfig:67:warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP
Let's make them built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 985626564eedc470ce2866e53938303368ad41b7 upstream.
adjust_lowmem_bounds is responsible for setting up the boundary for
lowmem/highmem. This needs to be setup before memblock reservations can
occur. At the time memblock reservations can occur, memory can also be
removed from the system. The lowmem/highmem boundary and end of memory
may be affected by this but it is currently not recalculated. On some
systems this may be harmless, on others this may result in incorrect
ranges being passed to the main memory allocator. Correct this by
recalculating the lowmem/highmem boundary after all reservations have
been made.
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Julien Grall <julien.grall@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 374d446d25d6271ee615952a3b7f123ba4983c35 upstream.
The logic for sanity_check_meminfo has become difficult to
follow. Clean up the code so it's more obvious what the code
is actually trying to do. Additionally, meminfo is now removed
so rename the function to better describe its purpose.
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Julien Grall <julien.grall@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6dbdd3c8558cad3b6d74cc357b408622d122331 upstream.
Under memory pressure, we start ageing pages, which amounts to parsing
the page tables. Since we don't want to allocate any extra level,
we pass NULL for our private allocation cache. Which means that
stage2_get_pud() is allowed to fail. This results in the following
splat:
[ 1520.409577] Unable to handle kernel NULL pointer dereference at virtual address 00000008
[ 1520.417741] pgd = ffff810f52fef000
[ 1520.421201] [00000008] *pgd=0000010f636c5003, *pud=0000010f56f48003, *pmd=0000000000000000
[ 1520.429546] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[ 1520.435156] Modules linked in:
[ 1520.438246] CPU: 15 PID: 53550 Comm: qemu-system-aar Tainted: G W 4.12.0-rc4-00027-g1885c397eaec #7205
[ 1520.448705] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB12A 10/26/2016
[ 1520.463726] task: ffff800ac5fb4e00 task.stack: ffff800ce04e0000
[ 1520.469666] PC is at stage2_get_pmd+0x34/0x110
[ 1520.474119] LR is at kvm_age_hva_handler+0x44/0xf0
[ 1520.478917] pc : [<ffff0000080b137c>] lr : [<ffff0000080b149c>] pstate: 40000145
[ 1520.486325] sp : ffff800ce04e33d0
[ 1520.489644] x29: ffff800ce04e33d0 x28: 0000000ffff40064
[ 1520.494967] x27: 0000ffff27e00000 x26: 0000000000000000
[ 1520.500289] x25: ffff81051ba65008 x24: 0000ffff40065000
[ 1520.505618] x23: 0000ffff40064000 x22: 0000000000000000
[ 1520.510947] x21: ffff810f52b20000 x20: 0000000000000000
[ 1520.516274] x19: 0000000058264000 x18: 0000000000000000
[ 1520.521603] x17: 0000ffffa6fe7438 x16: ffff000008278b70
[ 1520.526940] x15: 000028ccd8000000 x14: 0000000000000008
[ 1520.532264] x13: ffff7e0018298000 x12: 0000000000000002
[ 1520.537582] x11: ffff000009241b93 x10: 0000000000000940
[ 1520.542908] x9 : ffff0000092ef800 x8 : 0000000000000200
[ 1520.548229] x7 : ffff800ce04e36a8 x6 : 0000000000000000
[ 1520.553552] x5 : 0000000000000001 x4 : 0000000000000000
[ 1520.558873] x3 : 0000000000000000 x2 : 0000000000000008
[ 1520.571696] x1 : ffff000008fd5000 x0 : ffff0000080b149c
[ 1520.577039] Process qemu-system-aar (pid: 53550, stack limit = 0xffff800ce04e0000)
[...]
[ 1521.510735] [<ffff0000080b137c>] stage2_get_pmd+0x34/0x110
[ 1521.516221] [<ffff0000080b149c>] kvm_age_hva_handler+0x44/0xf0
[ 1521.522054] [<ffff0000080b0610>] handle_hva_to_gpa+0xb8/0xe8
[ 1521.527716] [<ffff0000080b3434>] kvm_age_hva+0x44/0xf0
[ 1521.532854] [<ffff0000080a58b0>] kvm_mmu_notifier_clear_flush_young+0x70/0xc0
[ 1521.539992] [<ffff000008238378>] __mmu_notifier_clear_flush_young+0x88/0xd0
[ 1521.546958] [<ffff00000821eca0>] page_referenced_one+0xf0/0x188
[ 1521.552881] [<ffff00000821f36c>] rmap_walk_anon+0xec/0x250
[ 1521.558370] [<ffff000008220f78>] rmap_walk+0x78/0xa0
[ 1521.563337] [<ffff000008221104>] page_referenced+0x164/0x180
[ 1521.569002] [<ffff0000081f1af0>] shrink_active_list+0x178/0x3b8
[ 1521.574922] [<ffff0000081f2058>] shrink_node_memcg+0x328/0x600
[ 1521.580758] [<ffff0000081f23f4>] shrink_node+0xc4/0x328
[ 1521.585986] [<ffff0000081f2718>] do_try_to_free_pages+0xc0/0x340
[ 1521.592000] [<ffff0000081f2a64>] try_to_free_pages+0xcc/0x240
[...]
The trivial fix is to handle this NULL pud value early, rather than
dereferencing it blindly.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33b5c38852b29736f3b472dd095c9a18ec22746f upstream.
We currently have the HSCTLR.A bit set, trapping unaligned accesses
at HYP, but we're not really prepared to deal with it.
Since the rest of the kernel is pretty happy about that, let's follow
its example and set HSCTLR.A to zero. Modern CPUs don't really care.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8581c7c8be172dac156a19d261f988a72ce596f upstream.
The board file for imx6sx-sdb overrides cpufreq operating points to use
higher voltages. This is done because the board has a shared rail for
VDD_ARM_IN and VDD_SOC_IN and when using LDO bypass the shared voltage
needs to be a value suitable for both ARM and SOC.
This only applies to LDO bypass mode, a feature not present in upstream.
When LDOs are enabled the effect is to use higher voltages than necessary
for no good reason.
Setting these higher voltages can make some boards fail to boot with ugly
semi-random crashes reminiscent of memory corruption. These failures only
happen on board rev. C, rev. B is reported to still work.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 54183bd7f766 ("ARM: imx6sx-sdb: add revb board and make it default")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3df1ec06353e51fc44563d2e7e18d42811af290 upstream.
Remove ADC channels that are not available by default on the sama5d3_xplained
board (resistor not populated) in order to not create confusion.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cdd31e5913c1f86dce7e201b086155b3f24896b upstream.
The voltage reference for the ADC is not 3V but 3.3V since it is connected to
VDDANA.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d80594936914e798b1b54b3bfe4bd68d8418966 upstream.
We save/restore registers around v7m_invalidate_l1 to address pointed
by r12, which is vector table, so the first eight entries are
overwritten with a garbage. We already have stack setup at that stage,
so use it to save/restore register.
Fixes: 6a8146f420be ("ARM: 8609/1: V7M: Add support for the Cortex-M7 processor")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7ede5a1f5905ac394cc8e61712a13e3c5cb7b8f upstream.
Since commit 35fa91eed817 ("ARM: kernel: merge core and init PLTs"),
the ARM module PLT code allocates all PLT entries in a single core
section, since the overhead of having a separate init PLT section is
not justified by the small number of PLT entries usually required for
init code.
However, the core and init module regions are allocated independently,
and there is a corner case where the core region may be allocated from
the VMALLOC region if the dedicated module region is exhausted, but the
init region, being much smaller, can still be allocated from the module
region. This puts the PLT entries out of reach of the relocated branch
instructions, defeating the whole purpose of PLTs.
So split the core and init PLT regions, and name the latter ".init.plt"
so it gets allocated along with (and sufficiently close to) the .init
sections that it serves. Also, given that init PLT entries may need to
be emitted for branches that target the core module, modify the logic
that disregards defined symbols to only disregard symbols that are
defined in the same section.
Fixes: 35fa91eed817 ("ARM: kernel: merge core and init PLTs")
Reported-by: Angus Clark <angus@angusclark.org>
Tested-by: Angus Clark <angus@angusclark.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 661e6b02b5aa82db31897f36e96324b77450fd7a upstream.
Hardware debugging in guests is not intercepted currently, it means
that a malicious guest can bring down the entire machine by writing
to the debug registers.
This patch enable trapping of all debug registers, preventing the
guests to access the debug registers. This includes access to the
debug mode(DBGDSCR) in the guest world all the time which could
otherwise mess with the host state. Reads return 0 and writes are
ignored (RAZ_WI).
The result is the guest cannot detect any working hardware based debug
support. As debug exceptions are still routed to the guest normal
debug using software based breakpoints still works.
To support debugging using hardware registers we need to implement a
debug register aware world switch as well as special trapping for
registers that may affect the host state.
Signed-off-by: Zhichao Huang <zhichao.huang@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 501ad27c67ed0b90df465f23d33e9aed64058a47 upstream.
We like living dangerously. Nothing explicitely forbids stack-protector
to be used in the HYP code, while distributions routinely compile their
kernel with it. We're just lucky that no code actually triggers the
instrumentation.
Let's not try our luck for much longer, and disable stack-protector
for code living at HYP.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c18927f51f4d390abdcf385bff5f995407ee732 upstream.
Current U-Boot enables the display already. Marking the regulator as
enabled on boot fixes sporadic panel initialization failures.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Misha Komarovskiy <zombah@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c7a5dce22b3f3cc44be098e2837fa6797edb8b8 upstream.
Fix potential races in kvm_psci_vcpu_on() by taking the kvm->lock
mutex. In general, it's a bad idea to allow more than one PSCI_CPU_ON
to process the same target VCPU at the same time. One such problem
that may arise is that one PSCI_CPU_ON could be resetting the target
vcpu, which fills the entire sys_regs array with a temporary value
including the MPIDR register, while another looks up the VCPU based
on the MPIDR value, resulting in no target VCPU found. Resolves both
races found with the kvm-unit-tests/arm/psci unit test.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reported-by: Levente Kurusa <lkurusa@redhat.com>
Suggested-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0cdefd5b5485ee6eb3512a75739d09a4090176ed upstream.
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f0c ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 448c077eeb02240c430db2a2c3bf5285a4c65d66 upstream.
'adr' yields a data-pointer, not a function-pointer.
Fixes: 999f934de195 ("ARM: omap5/dra7xx: Enable booting secondary
CPU in HYP mode")
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit acfa28b3649ec07775efaac0c00de2db39d71634 upstream.
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06dbf468a2c42bf6c327a8eaf11ecb3ea96196f9 upstream.
The ipq board has these rates as 25MHz, and not 19.2 and 27. I
copy/pasted from other boards that have those rates but forgot
to fix the rates here.
Fixes: 30fc4212d541 ("arm: dts: qcom: Add more board clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 680a0873e193bae666439f4b5e32c758e68f114c ]
This patch adds a quirk parameter to the arm_smccc_(smc/hvc) calls.
The quirk structure allows for specialized SMC operations due to SoC
specific requirements. The current arm_smccc_(smc/hvc) is renamed and
macros are used instead to specify the standard arm_smccc_(smc/hvc) or
the arm_smccc_(smc/hvc)_quirk function.
This patch and partial implementation was suggested by Will Deacon.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8413299cb3933dade6186bbee8363f190032107e ]
Since v4.10-rc1, the following logs appears in loop :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
[ 806.083772] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 806.090370] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 806.096494] usb usb6-port1: cannot disable (err = -32)
After analysis, xhci try to set link in U3 and returns an error.
Using snps,dis_u3_susphy_quirk fix this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7e431af8fa0b9ed9d74378c99514856211cb9db8 ]
Add PM support for DA850 device-tree boot.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b3405e345b5a098101b0c31b264c812bba045d9 upstream.
In kvm_free_stage2_pgd() we don't hold the kvm->mmu_lock while calling
unmap_stage2_range() on the entire memory range for the guest. This could
cause problems with other callers (e.g, munmap on a memslot) trying to
unmap a range. And since we have to unmap the entire Guest memory range
holding a spinlock, make sure we yield the lock if necessary, after we
unmap each PUD range.
Fixes: commit d5d8184d35c9 ("KVM: ARM: Memory virtualization setup")
Cc: Paolo Bonzini <pbonzin@redhat.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[ Avoid vCPU starvation and lockup detector warnings ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72f310481a08db821b614e7b5d00febcc9064b36 upstream.
We don't hold the mmap_sem while searching for VMAs (via find_vma), in
kvm_arch_prepare_memory_region, which can end up in expected failures.
Fixes: commit 8eef91239e57 ("arm/arm64: KVM: map MMIO regions at creation time")
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Eric Auger <eric.auger@rehat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
[ Handle dirty page logging failure case ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90f6e150e44a0dc3883110eeb3ab35d1be42b6bb upstream.
We don't hold the mmap_sem while searching for the VMAs when
we try to unmap each memslot for a VM. Fix this properly to
avoid unexpected results.
Fixes: commit 957db105c997 ("arm/arm64: KVM: Introduce stage2_unmap_vm")
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c2bf9f95983fe30aa2f6463cb761cd42c2d521a upstream.
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09f3510fb70a46c8921f2cf4a90dbcae460a6820 upstream.
Since early BCM5301X days we got abort handler that was removed by
commit 937b12306ea79 ("ARM: BCM5301X: remove workaround imprecise abort
fault handler"). It assumed we need to deal only with pending aborts
left by the bootloader. Unfortunately this isn't true for BCM5301X.
When probing PCI config space (device enumeration) it is expected to
have master aborts on the PCI bus. Most bridges don't forward (or they
allow disabling it) these errors onto the AXI/AMBA bus but not the
Northstar (BCM5301X) one.
iProc PCIe controller on Northstar seems to be some older one, without
a control register for errors forwarding. It means we need to workaround
this at platform level. All newer platforms are not affected by this
issue.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60b89f1928af80b546b5c3fd8714a62f6f4b8844 upstream.
On some DDR controllers, compatible with the sama5d3 one,
the sequence to enter/exit/re-enter the self-refresh mode adds
more constrains than what is currently written in the at91_idle
driver. An actual access to the DDR chip is needed between exit
and re-enter of this mode which is somehow difficult to implement.
This sequence can completely hang the SoC. It is particularly
experienced on parts which embed a L2 cache if the code run
between IDLE calls fits in it...
Moreover, as the intention is to enter and exit pretty rapidly
from IDLE, the power-down mode is a good candidate.
So now we use power-down instead of self-refresh. As we can
simplify the code for sama5d3 compatible DDR controllers,
we instantiate a new sama5d3_ddr_standby() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 017b5522d5e3 ("ARM: at91: Add new binding for sama5d3-ddramc")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e10889a3177340dcda7d29c6d8fbd97247b007b upstream.
This reverts commit cab43282682e ("ARM: at91/dt: sama5d2: Use new
compatible for ohci node")
It depends from commit 7150bc9b4d43 ("usb: ohci-at91: Forcibly suspend
ports while USB suspend") which was reverted and implemented
differently. With the new implementation, the compatible string must
remain the same.
The compatible string introduced by this commit has been used in the
default SAMA5D2 dtsi starting from Linux 4.8. As it has never been
working correctly in an official release, removing it should not be
breaking the stability rules.
Fixes: cab43282682e ("ARM: at91/dt: sama5d2: Use new compatible for ohci node")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f36ebaf21fdae99c091c67e8b6fab33969f2667 upstream.
When we fault in a page, we flush it to the PoC (Point of Coherency)
if the faulting vcpu has its own caches off, so that it can observe
the page we just brought it.
But if the vcpu has its caches on, we skip that step. Bad things
happen when *another* vcpu tries to access that page with its own
caches disabled. At that point, there is no garantee that the
data has made it to the PoC, and we access stale data.
The obvious fix is to always flush to PoC when a page is faulted
in, no matter what the state of the vcpu is.
Fixes: 2d58b733c876 ("arm64: KVM: force cache clean on page fault when caches are off")
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78162d48466d23c45a784034630c5928af631e3d upstream.
Enable DMA on uart1 to get a more reliable console.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef8d02d4a2c36f7a93e74c95a9c419353b310117 upstream.
Enable DMA on usart3 to get a more reliable console. This is especially
useful for automation and kernelci were a kernel with PROVE_LOCKING enabled
is quite susceptible to character loss, resulting in tests failure.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e3440481845b2ec22508f60837ee2cab2b6054f upstream.
The 64-bit get_user() wasn't clearing the high word due to a typo in the
error handler. The exception handler entry was already correct, though.
Noticed during recent usercopy test additions in lib/test_user_copy.c.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97a98ae5b8acf08d07d972c087b2def060bc9b73 upstream.
Asynchronous external abort is coded differently in DFSR with LPAE enabled.
Fixes: 9254970c "ARM: 8447/1: catch pending imprecise abort on unmask".
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f59b319111bbc3a5f32730c8a43b201e9522f52 upstream.
GPIO4_11 is on pin 152(MX6DL_PAD_KEY_ROW2) and not on pin
151(MX6DL_PAD_KEY_ROW1).
I found the error while booting a mainline kernel on APF6S SoM and
noticed the following message:
[ 2.609337] imx6dl-pinctrl 20e0000.iomuxc: pin MX6DL_PAD_KEY_ROW1
already requested by 20a8000.gpio:105; cannot claim for 20a8000.gpio:107
[ 2.621884] imx6dl-pinctrl 20e0000.iomuxc: pin-151 (20a8000.gpio:107)
status -22
[ 2.629303] spi_imx 2008000.ecspi: Can't get CS GPIO 107
With this patch, the message is gone and spi_imx driver probes correctly.
Fixes: bb728d662bed ("ARM: dts: add gpio-ranges property to iMX GPIO controllers")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 228dbbfb5d77f8e047b2a1d78da14b7158433027 upstream.
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Fixes: 5be6f62b0059 ("ARM: 6883/1: ptrace: Migrate to regsets framework")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90f92c631b210c1e97080b53a9d863783281a932 upstream.
The following patch was sketched by Russell in response to my
crashes on the PB11MPCore after the patch for software-based
priviledged no access support for ARMv8.1. See this thread:
http://marc.info/?l=linux-arm-kernel&m=144051749807214&w=2
I am unsure what is going on, I suspect everyone involved in
the discussion is. I just want to repost this to get the
discussion restarted, as I still have to apply this patch
with every kernel iteration to get my PB11MPCore Realview
running.
Testing by Neil Armstrong on the Oxnas NAS has revealed that
this bug exist also on that widely deployed hardware, so
we are probably currently regressing all ARM11MPCore systems.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: a5e090acbf54 ("ARM: software-based priviledged-no-access support")
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0e8faa7a5e894b0fc99d24be1b18685a92ea466 upstream.
This function clearly never worked and always returns true,
as pointed out by gcc-7:
arch/arm/mach-ux500/pm.c: In function 'prcmu_is_cpu_in_wfi':
arch/arm/mach-ux500/pm.c:137:212: error: ?:
using integer constants in boolean context, the expression
will always evaluate to 'true' [-Werror=int-in-bool-context]
With the added braces, the condition actually makes sense.
Fixes: 34fe6f107eab ("mfd : Check if the other db8500 core is in WFI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ea6af3216b092ec97129ac81bd95cf254c4b140 upstream.
This fixes commit ab8dd3aed011 ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV") where the Card Detect and Write Protect
pins were improperly configured.
Fixes: ab8dd3aed011 ("ARM: DTS: Add minimal Support for Logic PD DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ab5c2b662e2dcbb964099bf7f19e9dbc9ae5a41 upstream.
This patch fixes the following error:
sgtl5000 0-000a: Error reading chip id -6
imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
imx-sgtl5000 sound: snd_soc_register_card failed (-517)
The problem was that the pinctrl group was linked to the sound driver
instead of the codec node. Since the codec is probed first, the sys_mclk
was missing and it would therefore fail to initialize.
Fixes: b32e700256bc ("ARM: dts: imx: add Boundary Devices Nitrogen6_Max board")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d37d41a148c32389ed360e10a9f8a7cd37ce166 upstream.
Commit d1f3156fc8c7 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: d1f3156fc8c7 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23ab4c6183ac0679d80888b5c4cc1d528fcc21c2 upstream.
Commit 008a2ebcd677 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 008a2ebcd677 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce95077d0cdfcc8e40dea10a1680249831ccec77 upstream.
Commit 75813028bbd7 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 75813028bbd7 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c9faa84cb9c34852ad70cb175457ae21fc06f39b upstream.
Commit 76a8548ea987 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76a8548ea987 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c565d1a63ce241a0100f5d327c48dde87b4df76 upstream.
Commit da6269e7e3dd ("ARM: dts: omap4: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: da6269e7e3dd ("ARM: dts: omap4: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d8d6d3f2f7d553c479f24ab93767974a8c2dfad upstream.
Commit f8bf01611c99 ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: f8bf01611c99 ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9536fd30d41ae4f30d04762676e5f5f602e16aa8 upstream.
Commit 76155b378c59 ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76155b378c59 ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
