| Age | Commit message (Collapse) | Author |
|---|
|
commit 91d06971881f71d945910de128658038513d1b24 upstream.
Currently we do not have an isync, or any other context synchronizing
instruction prior to the slbie/slbmte in _switch() that updates the
SLB entry for the kernel stack.
However that is not correct as outlined in the ISA.
From Power ISA Version 3.0B, Book III, Chapter 11, page 1133:
"Changing the contents of ... the contents of SLB entries ... can
have the side effect of altering the context in which data
addresses and instruction addresses are interpreted, and in which
instructions are executed and data accesses are performed.
...
These side effects need not occur in program order, and therefore
may require explicit synchronization by software.
...
The synchronizing instruction before the context-altering
instruction ensures that all instructions up to and including that
synchronizing instruction are fetched and executed in the context
that existed before the alteration."
And page 1136:
"For data accesses, the context synchronizing instruction before the
slbie, slbieg, slbia, slbmte, tlbie, or tlbiel instruction ensures
that all preceding instructions that access data storage have
completed to a point at which they have reported all exceptions
they will cause."
We're not aware of any bugs caused by this, but it should be fixed
regardless.
Add the missing isync when updating kernel stack SLB entry.
Cc: stable@vger.kernel.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Flesh out change log with more ISA text & explanation]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 222f20f140623ef6033491d0103ee0875fe87d35 upstream.
This commit does simple conversions of rfi/rfid to the new macros that
include the expected destination context. By simple we mean cases
where there is a single well known destination context, and it's
simply a matter of substituting the instruction for the appropriate
macro.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Backport to 4.9, use RFI_TO_KERNEL in idle_book3s.S]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is just the first chunk of commit
222f20f140623ef6033491d0103ee0875fe87d35 upstream.
to fix a build error in the powerpc tree due to other backports
happening (and this full patch not being backported).
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Yves-Alexis Perez <corsac@debian.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yves-Alexis Perez <corsac@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8e90cb7bc04a509e821e82ab6ed7a8ef11ba333 upstream.
In the syscall exit path we may be returning to user or kernel
context. We already have a test for that, because we conditionally
restore r13. So use that existing test and branch, and bifurcate the
return based on that.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a08f828cf47e6c605af21d2cdec68f84e799c318 upstream.
Similar to the syscall return path, in fast_exception_return we may be
returning to user or kernel context. We already have a test for that,
because we conditionally restore r13. So use that existing test and
branch, and bifurcate the return based on that.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4979a7e71eb8da976cbe4a0a1fa50636e76b04f upstream.
For DYNAMIC_FTRACE_WITH_REGS, we should be passing-in the original set
of registers in pt_regs, to capture the state _before_ ftrace_caller.
However, we are instead passing the stack pointer *after* allocating a
stack frame in ftrace_caller. Fix this by saving the proper value of r1
in pt_regs. Also, use SAVE_10GPRS() to simplify the code.
Fixes: 153086644fd1 ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e1ba4f27f018742a1aa95d11e35106feba08ec1 upstream.
If we set a kprobe on a 'stdu' instruction on powerpc64, we see a kernel
OOPS:
Bad kernel stack pointer cd93c840 at c000000000009868
Oops: Bad kernel stack pointer, sig: 6 [#1]
...
GPR00: c000001fcd93cb30 00000000cd93c840 c0000000015c5e00 00000000cd93c840
...
NIP [c000000000009868] resume_kernel+0x2c/0x58
LR [c000000000006208] program_check_common+0x108/0x180
On a 64-bit system when the user probes on a 'stdu' instruction, the kernel does
not emulate actual store in emulate_step() because it may corrupt the exception
frame. So the kernel does the actual store operation in exception return code
i.e. resume_kernel().
resume_kernel() loads the saved stack pointer from memory using lwz, which only
loads the low 32-bits of the address, causing the kernel crash.
Fix this by loading the 64-bit value instead.
Fixes: be96f63375a1 ("powerpc: Split out instruction analysis part of emulate_step()")
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
[mpe: Change log massage, add stable tag]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
|
|
mtmsrd with L=1 only affects MSR_EE and MSR_RI bits, and we always
know what state those bits are, so the kernel MSR does not need to be
loaded when modifying them.
mtmsrd is often in the critical execution path, so avoiding dependency
on even L1 load is noticable. On a POWER8 this saves about 3 cycles
from the syscall path, and possibly a few from other exception returns
(not measured).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
tabort_syscall runs with RI=1, so a nested recoverable machine
check will load the paca into r13 and overwrite what we loaded
it with, because exceptions returning to privileged mode do not
restore r13.
Fixes: b4b56f9ecab4 (powerpc/tm: Abort syscalls in active transactions)
Cc: stable@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
MMU feature bits are defined such that we use the lower half to
present MMU family features. Remove the strict split of half and
also move Radix to a mmu family feature. Radix introduce a new MMU
model and strictly speaking it is a new MMU family. This also free
up bits which can be used for individual features later.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch provides VIRT_CPU_ACCOUTING to PPC32 architecture.
PPC32 doesn't have the PACA structure, so we use the task_info
structure to store the accounting data.
In order to reuse on PPC32 the PPC64 functions, all u64 data has
been replaced by 'unsigned long' so that it is u32 on PPC32 and
u64 on PPC64
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
We're approaching 20 locations where we need to check for ELF ABI v2.
That's fine, except the logic is a bit awkward, because we have to check
that _CALL_ELF is defined and then what its value is.
So check it once in asm/types.h and define PPC64_ELF_ABI_v2 when ELF ABI
v2 is detected.
We also have a few places where what we're really trying to check is
that we are using the 64-bit v1 ABI, ie. function descriptors. So also
add a #define for that, which simplifies several checks.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We also use MMU_FTR_RADIX to branch out from code path specific to
hash.
No functionality change.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The copy paste facility introduced in POWER9 provides an optimised
mechanism for a userspace application to copy a cacheline. This is
provided by a pair of instructions, copy and paste, while a third,
cp_abort (copy paste abort), provides a clean up of the state in case of
a failure.
The copy instruction will read a 128 byte cacheline and store it in an
internal buffer. The subsequent paste instruction will store this
internal buffer to memory and set a CR field if the paste succeeds.
Since the state of the copy paste buffer is internal (and not
architecturally visible), in the unlikely event of a context switch, the
state cannot be stored and the paste should therefore fail.
The cp_abort instruction exists to fail and clean up any such
interrupted copy paste sequence and is to be called by the kernel as
part of the context switch. Doing so prevents data from a preceding copy
in one process leaking into the paste of another.
This code enables use of the cp_abort instruction if a supported
processor is detected.
NOTE: this is for userspace only, not in kernel, and does not deal
with KVM guests.
Patch created with much assistance from Michael Neuling
<mikey@neuling.org>
Signed-off-by: Chris Smart <chris@distroguy.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Merge the support for live patching on ppc64le using mprofile-kernel.
This branch has also been merged into the livepatching tree for v4.7.
|
|
Add the kconfig logic & assembly support for handling live patched
functions. This depends on DYNAMIC_FTRACE_WITH_REGS, which in turn
depends on the new -mprofile-kernel ftrace ABI, which is only supported
currently on ppc64le.
Live patching is handled by a special ftrace handler. This means it runs
from ftrace_caller(). The live patch handler modifies the NIP so as to
redirect the return from ftrace_caller() to the new patched function.
However there is one particularly tricky case we need to handle.
If a function A calls another function B, and it is known at link time
that they share the same TOC, then A will not save or restore its TOC,
and will call the local entry point of B.
When we live patch B, we replace it with a new function C, which may
not have the same TOC as A. At live patch time it's too late to modify A
to do the TOC save/restore, so the live patching code must interpose
itself between A and C, and do the TOC save/restore that A omitted.
An additionaly complication is that the livepatch code can not create a
stack frame in order to save the TOC. That is because if C takes > 8
arguments, or is varargs, A will have written the arguments for C in
A's stack frame.
To solve this, we introduce a "livepatch stack" which grows upward from
the base of the regular stack, and is used to store the TOC & LR when
calling a live patched function.
When the patched function returns, we retrieve the real LR & TOC from
the livepatch stack, restore them, and pop the livepatch "stack frame".
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
|
|
Commit 70fe3d9 "powerpc: Restore FPU/VEC/VSX if previously used" introduces a
call to restore_math() late in the syscall return path, after MSR_RI has been
cleared. The MSR_RI flag is used to indicate whether the kernel can take
another exception or not. A cleared MSR_RI flag indicates that the kernel
cannot.
Unfortunately when a machine is under SLB pressure an SLB miss can occur
in restore_math() which (with MSR_RI cleared) leads to an unrecoverable
exception.
Unrecoverable exception 4100 at c0000000000088d8
cpu 0x0: Vector: 4100 at [c0000003fa473b20]
pc: c0000000000088d8: .load_vr_state+0x70/0x110
lr: c00000000000f710: .restore_math+0x130/0x188
sp: c0000003fa473da0
msr: 9000000002003030
current = 0xc0000007f876f180
paca = 0xc00000000fff0000 softe: 0 irq_happened: 0x01
pid = 1944, comm = K08umountfs
[link register ] c00000000000f710 .restore_math+0x130/0x188
[c0000003fa473da0] c0000003fa473e30 (unreliable)
[c0000003fa473e30] c000000000007b6c system_call+0x84/0xfc
The clearing of MSR_RI is actually an optimisation to avoid multiple MSR
writes, what must be disabled are interrupts. See comment in entry_64.S:
/*
* For performance reasons we clear RI the same time that we
* clear EE. We only need to clear RI just before we restore r13
* below, but batching it with EE saves us one expensive mtmsrd call.
* We have to be careful to restore RI if we branch anywhere from
* here (eg syscall_exit_work).
*/
At the point of calling restore_math() r13 has not been restored, as such, the
quick fix of turning MSR_RI back on for the call to restore_math() will
eliminate the occurrence of an unrecoverable exception.
We'd like to do a better fix in future.
Fixes: 70fe3d980f5f ("powerpc: Restore FPU/VEC/VSX if previously used")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Merge the ftrace changes to support -mprofile-kernel on ppc64le. This is
a prerequisite for live patching, the support for which will be merged
via the livepatch tree based on this topic branch.
|
|
The gcc switch -mprofile-kernel defines a new ABI for calling _mcount()
very early in the function with minimal overhead.
Although mprofile-kernel has been available since GCC 3.4, there were
bugs which were only fixed recently. Currently it is known to work in
GCC 4.9, 5 and 6.
Additionally there are two possible code sequences generated by the
flag, the first uses mflr/std/bl and the second is optimised to omit the
std. Currently only gcc 6 has the optimised sequence. This patch
supports both sequences.
Initial work started by Vojtech Pavlik, used with permission.
Key changes:
- rework _mcount() to work for both the old and new ABIs.
- implement new versions of ftrace_caller() and ftrace_graph_caller()
which deal with the new ABI.
- updates to __ftrace_make_nop() to recognise the new mcount calling
sequence.
- updates to __ftrace_make_call() to recognise the nop'ed sequence.
- implement ftrace_modify_call().
- updates to the module loader to surpress the toc save in the module
stub when calling mcount with the new ABI.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently the FPU, VEC and VSX facilities are lazily loaded. This is not
a problem unless a process is using these facilities.
Modern versions of GCC are very good at automatically vectorising code,
new and modernised workloads make use of floating point and vector
facilities, even the kernel makes use of vectorised memcpy.
All this combined greatly increases the cost of a syscall since the
kernel uses the facilities sometimes even in syscall fast-path making it
increasingly common for a thread to take an *_unavailable exception soon
after a syscall, not to mention potentially taking all three.
The obvious overcompensation to this problem is to simply always load
all the facilities on every exit to userspace. Loading up all FPU, VEC
and VSX registers every time can be expensive and if a workload does
avoid using them, it should not be forced to incur this penalty.
An 8bit counter is used to detect if the registers have been used in the
past and the registers are always loaded until the value wraps to back
to zero.
Several versions of the assembly in entry_64.S were tested:
1. Always calling C.
2. Performing a common case check and then calling C.
3. A complex check in asm.
After some benchmarking it was determined that avoiding C in the common
case is a performance benefit (option 2). The full check in asm (option
3) greatly complicated that codepath for a negligible performance gain
and the trade-off was deemed not worth it.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Move load_vec in the struct to fill an existing hole, reword change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fixup
|
|
This is only used in one location, open code it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
HMT_MEDIUM_LOW_HAS_PPR is only used in once place, open code it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
No need to execute mflr twice.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Move all our context switch SPR save and restore code into two
helpers. We do a few optimisations:
- Group all mfsprs and all mtsprs. In many cases an mtspr sets a
scoreboarding bit that an mfspr waits on, so the current practise of
mfspr A; mtspr A; mfpsr B; mtspr B is the worst scheduling we can
do.
- SPR writes are slow, so check that the value is changing before
writing it.
A context switch microbenchmark using yield():
http://ozlabs.org/~anton/junkcode/context_switch2.c
./context_switch2 --test=yield 0 0
shows an improvement of almost 10% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Writing the MSR is slow, so we want to avoid it whenever possible.
A subsequent patch will add a debug option that strictly manages the
FP/VMX/VSX unavailable bits. For now just remove it, matching what
we do in other areas of the kernel (eg enable_kernel_altivec()).
A context switch microbenchmark using yield():
http://ozlabs.org/~anton/junkcode/context_switch2.c
./context_switch2 --test=yield --fp 0 0
shows an improvement of almost 3% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The API for calling do_syscall_trace_enter() is currently sensible
enough, it just returns the (modified) syscall number.
However once we enable seccomp filter it will get more complicated. When
seccomp filter runs, the seccomp kernel code (via SECCOMP_RET_ERRNO), or
a ptracer (via SECCOMP_RET_TRACE), may reject the syscall and *may* or may
*not* set a return value in r3.
That means the assembler that calls do_syscall_trace_enter() can not
blindly return ENOSYS, it needs to only return ENOSYS if a return value
has not already been set.
There is no way to implement that logic with the current API. So change
the do_syscall_trace_enter() API to make it deal with the return code
juggling, and the assembler can then just return whatever return code it
is given.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
|
|
Currently on powerpc we have our own #define for the highest (negative)
errno value, called _LAST_ERRNO. This is defined to be 516, for reasons
which are not clear.
The generic code, and x86, use MAX_ERRNO, which is defined to be 4095.
In particular seccomp uses MAX_ERRNO to restrict the value that a
seccomp filter can return.
Currently with the mismatch between _LAST_ERRNO and MAX_ERRNO, a seccomp
tracer wanting to return 600, expecting it to be seen as an error, would
instead find on powerpc that userspace sees a successful syscall with a
return value of 600.
To avoid this inconsistency, switch powerpc to use MAX_ERRNO.
We are somewhat confident that generic syscalls that can return a
non-error value above negative MAX_ERRNO have already been updated to
use force_successful_syscall_return().
I have also checked all the powerpc specific syscalls, and believe that
none of them expect to return a non-error value between -MAX_ERRNO and
-516. So this change should be safe ...
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
|
|
This patch changes the syscall handler to doom (tabort) active
transactions when a syscall is made and return very early without
performing the syscall and keeping side effects to a minimum (no CPU
accounting or system call tracing is performed). Also included is a
new HWCAP2 bit, PPC_FEATURE2_HTM_NOSC, to indicate this
behaviour to userspace.
Currently, the system call instruction automatically suspends an
active transaction which causes side effects to persist when an active
transaction fails.
This does change the kernel's behaviour, but in a way that was
documented as unsupported. It doesn't reduce functionality as
syscalls will still be performed after tsuspend; it just requires that
the transaction be explicitly suspended. It also provides a
consistent interface and makes the behaviour of user code
substantially the same across powerpc and platforms that do not
support suspended transactions (e.g. x86 and s390).
Performance measurements using
http://ozlabs.org/~anton/junkcode/null_syscall.c indicate the cost of
a normal (non-aborted) system call increases by about 0.25%.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PACA_DSCR offset macro tracks dscr_default element in the paca
structure. Better change the name of this macro to match that of the
data element it tracks. Makes the code more readable.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This reverts commit feba40362b11341bee6d8ed58d54b896abbd9f84.
Although the principle of this change is good, the implementation has a
few issues.
Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.
Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.
So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.
NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.
Fixes: feba40362b11 ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch changes the syscall handler to doom (tabort) active
transactions when a syscall is made and return immediately without
performing the syscall.
Currently, the system call instruction automatically suspends an
active transaction which causes side effects to persist when an active
transaction fails.
This does change the kernel's behaviour, but in a way that was
documented as unsupported. It doesn't reduce functionality because
syscalls will still be performed after tsuspend. It also provides a
consistent interface and makes the behaviour of user code
substantially the same across powerpc and platforms that do not
support suspended transactions (e.g. x86 and s390).
Performance measurements using
http://ozlabs.org/~anton/junkcode/null_syscall.c
indicate the cost of a system call increases by about 0.5%.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Acked-By: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We currently have a "special" syscall for switching endianness. This is
syscall number 0x1ebe, which is handled explicitly in the 64-bit syscall
exception entry.
That has a few problems, firstly the syscall number is outside of the
usual range, which confuses various tools. For example strace doesn't
recognise the syscall at all.
Secondly it's handled explicitly as a special case in the syscall
exception entry, which is complicated enough without it.
As a first step toward removing the special syscall, we need to add a
regular syscall that implements the same functionality.
The logic is simple, it simply toggles the MSR_LE bit in the userspace
MSR. This is the same as the special syscall, with the caveat that the
special syscall clobbers fewer registers.
This version clobbers r9-r12, XER, CTR, and CR0-1,5-7.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We have code to do syscall tracing which is disabled at compile time by
default. It's not been touched since the dawn of time (ie. v2.6.12).
There are now better ways to do syscall tracing, ie. using the
raw_syscall, or syscall tracepoints.
For the specific case of tracing syscalls at boot on a system that
doesn't get to userspace, you can boot with:
trace_event=syscalls tp_printk=on
Which will trace syscalls from boot, and echo all output to the console.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently when we back trace something that is in a syscall we see
something like this:
[c000000000000000] [c000000000000000] SyS_read+0x6c/0x110
[c000000000000000] [c000000000000000] syscall_exit+0x0/0x98
Although it's entirely correct, seeing syscall_exit at the bottom can be
confusing - we were exiting from a syscall and then called SyS_read() ?
If we instead change syscall_exit to be a local label we get something
more intuitive:
[c0000001fa46fde0] [c00000000026719c] SyS_read+0x6c/0x110
[c0000001fa46fe30] [c000000000009264] system_call+0x38/0xd0
ie. we were handling a system call, and it was SyS_read().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Once upon a time, at least 9 years ago (< 2.6.12), _TIF_SYSCALL_T_OR_A
meant "TRACE or AUDIT". But these days it means TRACE or AUDIT or
SECCOMP or TRACEPOINT or NOHZ.
All of those are implemented via syscall_dotrace() so rename the flag to
that to try and clarify things.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Instead of passing in the stack address of the link register
to be modified, just pass in the old value and return the
new value and rely on ftrace_graph_caller to do the
modification.
This removes the exception handling around the stack update -
it isn't needed and we weren't consistent about it. Later on
we would do an unprotected modification:
if (!ftrace_graph_entry(&trace)) {
*parent = old;
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
mod_return_to_handler is the same as return_to_handler, except
it handles the change of the TOC (r2). Add this into
return_to_handler and remove mod_return_to_handler.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Back in 7230c5644188 ("powerpc: Rework lazy-interrupt handling") we
added a call out to restore_interrupts() (written in c) before calling
do_notify_resume:
bl restore_interrupts
addi r3,r1,STACK_FRAME_OVERHEAD
bl do_notify_resume
Unfortunately do_notify_resume takes two arguments, the second one
being the thread_info flags:
void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags)
We do populate r4 (the second argument) earlier, but
restore_interrupts() is free to muck it up all it wants. My guess is
the gcc compiler gods shone down on us and its register allocator
never used r4. Sometimes, rarely, luck is on our side.
LLVM on the other hand did trample r4.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Handle Hypervisor Maintenance Interrupt (HMI) in Linux. This patch implements
basic infrastructure to handle HMI in Linux host. The design is to invoke
opal handle hmi in real mode for recovery and set irq_pending when we hit HMI.
During check_irq_replay pull opal hmi event and print hmi info on console.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We now only support cpus that use an SLB, so we don't need an MMU
feature to indicate that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Correct the DSCR SPR becoming temporarily corrupted if a task is
context switched during a transaction.
The problem occurs while suspending the task and is caused by saving
the DSCR to thread.dscr after it has already been set to the CPU's
default value:
__switch_to() calls __switch_to_tm()
which calls tm_reclaim_task()
which calls tm_reclaim_thread()
which calls tm_reclaim()
where the DSCR is set to the CPU's default
__switch_to() calls _switch()
where thread.dscr is set to the DSCR
When the task is resumed, it's transaction will be doomed (as usual)
and the DSCR SPR will be corrupted, although the checkpointed value
will be correct. Therefore the DSCR will be immediately corrected by
the transaction aborting, unless it has been suspended. In that case
the incorrect value can be seen by the task until it resumes the
transaction.
The fix is to treat the DSCR similarly to the TAR and save it early
in __switch_to().
A program exposing the problem is added to the kernel self tests as:
tools/testing/selftests/powerpc/tm/tm-resched-dscr.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
CC: <stable@vger.kernel.org> [v3.10+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Since commit "efcac65 powerpc: Per process DSCR + some fixes (try#4)"
it is no longer possible to set the DSCR on a per-CPU basis.
The old behaviour was to minipulate the DSCR SPR directly but this is no
longer sufficient: the value is quickly overwritten by context switching.
This patch stores the per-CPU DSCR value in a kernel variable rather than
directly in the SPR and it is used whenever a process has not set the DSCR
itself. The sysfs interface (/sys/devices/system/cpu/cpuN/dscr) is unchanged.
Writes to the old global default (/sys/devices/system/cpu/dscr_default)
now set all of the per-CPU values and reads return the last written value.
The new per-CPU default is added to the paca_struct and is used everywhere
outside of sysfs.c instead of the old global default.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When testing the ftrace function tracer, I realised that ftrace_caller
and mcount are called from modules and they both call into C, therefore
they need the ABIv2 global entry point to establish r2.
Signed-off-by: Anton Blanchard <anton@samba.org>
|
|
Change how we setup registers for ret_from_kernel_thread. In
ABIv1, instead of passing a function descriptor in, dereference
it and pass the target in directly.
Use ppc_global_function_entry to get it right on both ABIv1 and ABIv2.
Signed-off-by: Anton Blanchard <anton@samba.org>
|
|
To establish addressability quickly, ABIv2 requires the target
address of the function being called to be in r12. Fix a number of
places in assembly code that we do indirect function calls.
We need to avoid function descriptors on ABIv2 too.
Signed-off-by: Anton Blanchard <anton@samba.org>
|
|
There is no need to create a function descriptor for the system call
table. By using one we force the system call table into the text
section and it really belongs in the rodata section.
This also removes another use of dot symbols.
Signed-off-by: Anton Blanchard <anton@samba.org>
|
|
We have a number of places where we load the text address of a local
function and indirectly branch to it in assembly. Since it is an
indirect branch binutils will not know to use the function text
address, so that trick wont work.
There is no need for these functions to have a function descriptor
so we can replace it with a label and remove the dot symbol.
Signed-off-by: Anton Blanchard <anton@samba.org>
|
|
binutils is smart enough to know that a branch to a function
descriptor is actually a branch to the functions text address.
Alan tells me that binutils has been doing this for 9 years.
Signed-off-by: Anton Blanchard <anton@samba.org>
|
