Age | Commit message (Collapse) | Author |
|
I don't know where that mcp258x came from but it really is a mcp2515.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Provide proper configuration for VGEN3, to make sure it's is always powered
which allows that rail to be automatically switched to 1.8 volts
for proper UHS-I operation. By default it's disabled.
With UHS-I enabled:
[ 104.153898] mmc1: new ultra high speed SDR104 SDHC card at address 59b4
[ 104.166202] mmcblk1: mmc1:59b4 USD00 15.0 GiB
[ 104.173923] mmcblk1: p1
root@colibri-imx6:~# hdparm -t /dev/mmcblk1
/dev/mmcblk1:
Timing buffered disk reads: 226 MB in 3.01 seconds = 75.01 MB/sec
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
This commit adds a sleep state to the ixora devicetree. This prevents
backfeeding when sending the module to any sleep state.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Copied v1.1 devicetree and adopted it for v1.2 of the Ixora board.
Added the devicetree in the Makefile
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
This patch prepares the devicetree for the new Ixora V1.2 where we are
able to turn off the supply of the can transceiver. This implies to use
a sleep state on transmission pins in order to prevent backfeeding.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
If someone wants to add settings to the phy it is necessary to actually add the phy. This commit includes micrel,led-mode that is set to the default value, prepared for someone who wants to change this.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
For iptables filtering to work we need the NF_FILTER kernel module.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
This adds the proper phy-supply to the fec. This supply is actually
switched by a clock that is now properly stated. This adds the
advantage to add a delay for that particular regulator that is needed.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Add sleep state to the card-detect-pin. This is reducing the V_Batt
current on internal RTC if the module is sent to poweroff.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
This adds the enable-pin to uart2 that controls the transceiver for uart2/4.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit 07a8f35650e711666cf42f4962792d87b3b39b09)
|
|
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan modes to imx6ull-colibri-eval-v3.dtsi
where they belong.
Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit 1865142fd6a9dff221ace05fcbd704b5d86523df)
|
|
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit fb97f0b4043af52820cb4c2ca40fe855f8746e90)
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
All PWM clock instances have their clock gate. Add these consistently.
Fixes freezing the kernel when one of these instances is used with
IMX6UL_CLK_DUMMY as its clock source.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
(cherry picked from commit cd5d7ba49df7918732915a31bfc0f72827bebc2c)
|
|
The file uses linux,keycode = <KEY_POWER>;, so include
the header which defines KEY_POWER.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
(cherry picked from commit 479e0bae1ddfe3ec527634c241fadae558966323)
|
|
Reduce the current drawn from VCC_BATT when the main power on the 3V3 pins
to the module are switched off.
This switches off SoC internal pull resistors which are provided on the module
for TAMPER7 and TAMPER9 SoC pin and switches on a pull down instead of a pullup
for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Force HS200 by masking bit 63 of the SDHCI capability register.
The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With
that the stack checks bit 63 to descide whether HS400 is available.
Using sdhci-caps-mask allows to mask bit 63. The stack then selects
HS200 as operating mode.
This prevents rare communication errors with minimal effect on
performance:
sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL status REF not lock!
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
There is no fixed 1.8V regulator. VDDD is connected to the PMIC.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add support for Aster Carrier Board with Colibri iMX6ULL.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
The current Colibri iMX7 device tree are prepared for flexcan1 and
flexcan2. However their settings are different and the integration
is done to a different degree.
Unify that.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Switch on 22 kOhm pull ups and lower the I2C frequency to around 40kHz
to get a more reliable communication.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
The apalis has a 8 and 4 bit SD/MMC interface.
Switch on a 100k pull up on the card detect pins for carrier boards
which leave the pin floating.
Switch on hysteresis in case the signal has slow rise or fall times.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
On imx6 the SGTL5000 audio codec supply voltage is 3.3V and
not 2.5V as might have been copied over from other modules.
Output is slightly overamplified if the value is not corrected,
which may lead to signal clipping.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
The i.MX6 ULL's watchdog is used to reset the SoC on reboot. The watchdog is
configured to use the SoC's internal reset signal which does not generate a
reset pulse on nRESET_OUT. Change the watchdog configuration to use a SoC
external HW signal.
This will additionally change the 'Reset cause' message from U-Boot
from WDOG to POR.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Use a pinmux configuration for SD/MMC card detect and SPI chip
select instead of relying on reset/boot settings. There have
been no adverse effects observed, but it seems sensible to mux
the pads explicitly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
The device tree got changed to use the simple card driver, so enable it
in the defconfig.
While at it remove the IMX_SGTL5000 driver now replaced by the simple card driver.
While at it remove the unused ESAI driver.
While at it remove the unused CS42XX8_I2C codec driver.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
|
|
The Capacitive Touch Adapter is an interface board designed to easily
connect the Capacitive Touch Display 7" Parallel to the Colibri Carrier
boards which do not have PCAP connector yet available on board.
Change the pins for interrupt and reset to those defined in the
Capacitive Touch Adapter's datasheet.
While at it remove the '#ifdef PCAP' in favour of disabled nodes.
That way one can fixup the device tree in U-Boot to disable the
pwm nodes and enable the connected touch controller.
e.g. for a Colibri iMX6S/DL:
Colibri iMX6 # setenv fdt_fixup 'fdt addr ${fdt_addr_r} && fdt resize && fdt set /soc/aips-bus@02100000/i2c@021a8000/atmel_mxt_ts@4a status okay; fdt set /soc/aips-bus@02000000/pwm@02080000 status disabled; fdt set /soc/aips-bus@02000000/pwm@0208c000 status disabled'
Colibri iMX6 # saveenv
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Toradex Carrier boards use the ST M41T0 RTC (not M41T00). The RTC
is almost the same, but the M41T0 needs some special handling in
case the oscillator fails. Now that support for this difference is
available, using the new compatible string to make use of it.
Sync with commit 10e718b1c60c4e490e6972cfa58e97fcf5260685
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Synced with 558d378d522189ad68fcb00aff05fd134bf20924
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Add mxt nodes to dts and gpio-reset functionality.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Synchronize with commit fcfdb9c32075501e64751cc6a79fd91d15933692
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Prepare FlexCAN use on SODIMM 55/63. Those SODIMM pins are compatible
for CAN bus use with several modules from the Colibri family.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Commit 833f2cbf7091 ("ARM: dts: imx6: change the core clock of spdif")
changed many more clocks than only the SPDIF core clock as stated in
the commit message.
The MLB clock has been added and this causes SPDIF regression as
reported by Xavi Drudis Ferran and also in this forum post:
https://forum.digikey.com/thread/34240
The MX6Q Reference Manual does not mention that MLB is a clock related
to SPDIF, so change it back to a dummy clock to restore SPDIF
functionality.
Thanks to Ambika for providing the fix at:
https://community.nxp.com/thread/387131
Fixes: 833f2cbf7091 ("ARM: dts: imx6: change the core clock of spdif")
Cc: <stable@vger.kernel.org> # 4.4.x
Reported-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit f065e9e4addd75c21bb976bb2558648bf4f61de6)
This fix was correct, but overwritten by commit 833f2cbf7091099baee28136dc68678e974c0ac5.
MLB (Media Local Bus) Clock is in fact not related to SPDIF according to the MX6Q Reference
Manual. Tested playback and record on pulseaudio with 44.1kHz samples.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
The Colibri iMX6ULL 256MB crashes in resume if the M/F mix domain is
powered down when suspending.
With this workaround this does not happen.
Crash looks as follows:
root@colibri-imx6ull:~# echo +3 > /sys/class/rtc/rtc1/wakealarm; echo mem > /sys/power/state
[ 52.800741] PM: Syncing filesystems ... done.
[ 52.856715] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 52.865669] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 52.875024] Suspending console(s) (use no_console_suspend to debug)
[ 52.950638] PM: suspend of devices complete after 68.211 msecs
[ 52.952506] PM: late suspend of devices complete after 1.835 msecs
[ 52.954292] PM: noirq suspend of devices complete after 1.757 msecs
[ 52.954300] Disabling non-boot CPUs ...
[ 52.954307] Turn off M/F mix!
[ 52.955663] PM: noirq resume of devices complete after 1.222 msecs
[ 52.956767] imx-sdma 20ec000.sdma: loaded firmware 3.3
[ 52.957669] PM: early resume of devices complete after 1.411 msecs
[ 52.959140] gpmi-nand 1806000.gpmi-nand: use legacy bch geometry
[ 53.005653] Suspended for 2.907 seconds
[ 53.012207] PM: resume of devices complete after 54.507 msecs
[ 53.073751] Restarting tasks ... done.
root@colibri-imx6ull:~# [ 55.049753] gpmi-nand 1806000.gpmi-nand: DMA timeout, last DMA :2
[ 55.056377] gpmi-nand 1806000.gpmi-nand: Show GPMI registers :
[ 55.062835] gpmi-nand 1806000.gpmi-nand: offset 0x000 : 0x00000000
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 3e1b857786f0d46a92b3a4d7878767883ed90bdc)
|
|
To operate RS-485 on Toradex Carrier Boards a low active RTS signal
is required. Furthermore, a low active RTS signal requires the
receiver to be active (this seems to be a hardware limitation of the
i.MX UART).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Remove duplicate nodes introduced with the move to L4.9.11
release.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
The new Apalis iMX6 Mezzanine board allows access to the MIPI-CSI2
interface from the evaluation board. The current device tree has
different GPIO pin assignments for the camera reset and power pins.
Change the pin assignment to use Apalis GPIO1 for reset and Apalis
GPIO2 for power down.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add timings for LTTD1280800101-L4WH-CT1 panel used in the new
Capacitive Touch 10.1" LVDS display.
Note that the color mapping is to be set as follows:
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
The Atmel maXTouch multitouch controller driver does not control the
reset line connected to the chip. Use a GPIO reset controller node to
release the reset line and make the controller work.
Note that both the reset controller's and the mxt mutitouch controller's
node are set to disabled. Either change this in the dtsi source or fix
this from U-Boot if you use an Atmel maXTouch multitouch controller.
setenv fdt_fixup 'fdt addr ${fdt_addr_r} && fdt set /soc/aips-bus@02100000/i2c@021a0000/atmel_mxt_ts@4a status okay && fdt set /mxt-reset status okay'
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Configure Ethernet clock source for each FEC instance individually.
This allows to use different clock source setting for the two FEC
controllers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Exit early in case General-Purpose Registers are missing. This makes
sure that clock is always freed properly (clk_put).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Add alias for Ethernet controllers. This allows code to determine
id of controllers using of_alias_get_id.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Commit 95c163471135 ("usb: chipidea: use of extcon framework to
work for non OTG case") requires both pins to be specified (ID and
VBUS pin) to work correctly.
Fix the remaining dts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|