| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2014-10-30 | dtb: move trdx pinmux definitions into trdx filesColibri_iMX6_LinuxImageV2.3Beta4_20141113Apalis_iMX6_LinuxImageV2.3Beta3_20141031 | Max Krummenacher | |
| The Freescale provided files imx6qdl.dtsi, imx6q.dtsi provide among other things pinmux definitions. We added missing definitions to these files, however that could become a merging nightmare in the future. Move our additions into apalis/colibri files and use names which likely do not collide with future upstream additions. | |||
| 2014-10-28 | Apalis/Colibri iMX6: add deactivated RS485 setting | Max Krummenacher | |
| 2014-10-01 | apalis-imx6, colibri-imx6: emmc vccq is 3.3V only | Max Krummenacher | |
| 2014-10-01 | colibri-imx6: fix soundcard names | Max Krummenacher | |
| 2014-09-18 | Colibri iMX6 dtb: enable the buffers for RDnWR, nPWE | Max Krummenacher | |
| This enables the buffers which bring the WE# signal to SODIMM-93/99 and tri-states the CPU pins directly connected to SODIMM-93/99. | |||
| 2014-09-18 | Colibri iMX6 dtb: add all not muxed pin as gpio | Max Krummenacher | |
| All pins not assigned to other functionality are muxed to be gpio. This allows for later sysfs access to these pins. Some USB OTG control signals are among the list as the driver for these is not yet ready. | |||
| 2014-09-18 | Colibri iMX6 dtb: enable/fix UART A, UART C pinmuxing | Max Krummenacher | |
| UART A was lacking DCD/DSR/DTR muxing, UART C pinmuxing was set for DCE. | |||
| 2014-09-18 | Colibri iMX6 dtb: add MIC_GND control | Max Krummenacher | |
| MIC_GND is controlled with a FET. With a pullup set in the dtb MIC_GND is active by default. | |||
| 2014-09-18 | Colibri iMX6 dtb: make the power key low active | Max Krummenacher | |
| On the evaluation board is a pull down on this line, thus low active makes more sense. | |||
| 2014-09-18 | Colibri iMX6 dtb: remove EIM_WAIT from weim | Max Krummenacher | |
| 2014-09-15 | Colibri iMX6 dtb: enable weim interface | Max Krummenacher | |
| Enable the external memory bus, aka weim. Define a sram at CS0 and one at CS1, each in non multiplexed mode. | |||
| 2014-09-11 | Colibri iMX6 dtb: enable OTG port to work as peripheral | Max Krummenacher | |
| 2014-09-11 | Colibri iMX6 dtb: fix SPI to SOC instance mapping | Max Krummenacher | |
| 2014-09-11 | Colibri iMX6 dtb: fix PWM to SOC instance mapping | Max Krummenacher | |
| Fix the mapping of PWM<A> to SOC pwmX mapping and set the second SOC pin to input on PWM<A>, PWM<D>. | |||
| 2014-09-10 | mach-imx6q.c: fix typo in error msg | Max Krummenacher | |
| Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> | |||
| 2014-09-10 | imx6qdl-colibri.dtsi: change DI assignment and LCD pixformat | Max Krummenacher | |
| 2014-09-10 | colibri_imx6_defconfig: CMA size for S and DL | Max Krummenacher | |
| Make the CMA size half the RAM size or 256MB whatever is less. Thus on a Colibri iMX6S (with 256MB RAM) CMA will be 128MB, on a Colibri iMX6DL (with 512MB RAM) CMA will be 256MB. | |||
| 2014-09-04 | imx6qdl-colibri.dtsi: configure stmpe adc | Max Krummenacher | |
| 2014-09-04 | imx6 defconfig: remove CONFIG_WATCHDOG_NOWAYOUT | Max Krummenacher | |
| Colibri/Apalis Txx and Colibri VFxx have this configuration also not set. Be consistent. | |||
| 2014-09-04 | imx6qdl.dtsi: use SION to enable phy clock out | Max Krummenacher | |
| 2014-09-04 | imx6qdl-colibri.dtsi: fix pin assignements | Max Krummenacher | |
| 2014-09-04 | imx6qdl-colibri.dtsi: fix memory region | Max Krummenacher | |
| 2014-09-04 | imx6dl-colibri-eval-v3.dts: fix i2c assignements | Max Krummenacher | |
| 2014-09-04 | colibri_imx6_defconfig: reduce CONFIG_CMA_SIZE_MBYTES | Max Krummenacher | |
| 2014-09-04 | imx6qdl-colibri.dtsi: correct MMC bus width | Max Krummenacher | |
| 2014-09-03 | apalis_imx6_android_defconfig: add defconfig for android | Daniel Kochmanski | |
| 2014-09-01 | arm: imx6: fix pcie by disabling rc/ep test mode | Marcel Ziswiler | |
| Fix PCIe operation by disabling RC/EP test mode which according to the following community forum post is only used on the PCIe EP/RC validation system and otherwise prevent PCIe from working properly: https://community.freescale.com/thread/328257 | |||
| 2014-08-20 | stmpe-adc: enable it for Colibri/Apalis iMX6 | Max Krummenacher | |
| imx6qdl-apalis.dtsi: enable stmpe-adc in device tree defconfig: add stmpe-adc to minimal defconfig | |||
| 2014-08-18 | colibri-t30: add inital device tree and defconfig | Max Krummenacher | |
| 2014-08-18 | imx6qdl.dtsi: add additional pin groups | Max Krummenacher | |
| Add groups required by colibri-imx6 | |||
| 2014-08-14 | imx6q-apalis-eval.dts: fix comment | Max Krummenacher | |
| 2014-07-18 | apalis_imx6_defconfig: add CONFIG_NEW_LEDSApalis_iMX6_LinuxImageV2.3Beta1_20140804 | Max Krummenacher | |
| 2014-07-10 | apalis_imx6_defconfig: add fusion-F0710A as a module | Max Krummenacher | |
| Enable the TouchRevolution Fusion 7 and 10 multi-touch controller driver to be built as a module. While at it remove NEW_LEDS which is enabled through dependencies. | |||
| 2014-07-10 | ENGR00318392 ARM:imx6x: Save/restore SCU and some CP15 registers across ↵ | Ranjani Vaidyanathan | |
| suspend/resume This patch ensures that the SCU and certain A9 CP15 registers state are maintained across a suspend/resume cycle: 1. Need to ensure that SCU standby bit is set again after suspend/resume cycle, else the system will never WAIT mode after a suspend/resume cycle. This bit should be enabled on all SMP systems immaterial of whether CPUIDLE is enabled or not. 2. Several A9 errata workarounds involve setting bits in the ARM diagnostic register. Save/restore this register across a suspend/resume cycle. 3. Save and restore the A9 power control register also. Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com> (cherry picked from commit 7b5b4ef5b3cdc65c0576f87cfa52bcca1bda8b33) (cherry picked from commit 2a69800d94f182e975e4ed3ae2e64d30d35a3603) | |||
| 2014-07-10 | ENGR00309838 ARM: imx6sl: gpc: add chip revision check for dispmix | Robby Cai | |
| The dispmix feature works without problem since TO1.2. This patch adds the back-compatibility for older chip. Signed-off-by: Robby Cai <r63905@freescale.com> (cherry picked from commit a187b916d55052fed10de1797009250095b598fb) (cherry picked from commit dd27604b9d2a1bd294b3d8800e547bc526f87df7) | |||
| 2014-07-10 | input: touchscreen: fusion: add device tree integration | Max Krummenacher | |
| Add device tree integration and add the device to the dtb. i2c device, interrupt and reset GPIO can be specified in the dts as follows: Note that additionally you may have to set the pinmuxing for the pins to be GPIO. &i2c1 { status = "okay"; pcap@10 { /* TouchRevolution Fusion 7 and 10 multi-touch controller */ compatible = "touchrevolution,fusion-f0710a"; reg = <0x10>; gpios = <&gpio6 10 0 /* MXM-11, Pen down interrupt */ &gpio6 9 0 /* MXM-13, Reset interrupt */ >; }; | |||
| 2014-07-08 | apalis-imx6 dtb: cleanup and correct eval vs. module | Max Krummenacher | |
| 2014-07-08 | imx6qdl.dtsi: add uart5 pinctrl | Max Krummenacher | |
| 2014-07-07 | imx6qdl.dtsi: add a label for rhe snvs-rtc node | Max Krummenacher | |
| 2014-07-07 | apalis_imx6_defconfig: remove CONFIG_INPUT_EVBUG | Max Krummenacher | |
| 2014-07-07 | regulator: allow GPIO 0 to be used for an enable signal | Max Krummenacher | |
| GPIO number 0 *is* legal and must be accepted. Set .ena_gpio to -ENODEV on regulators having no GPIO in preparation of a code change to accept GPIO 0 in the config. | |||
| 2014-06-25 | apalis-imx6: add initial defconfig | Max Krummenacher | |
| 2014-06-25 | apalis-imx6: add initial device tree | Max Krummenacher | |
| 2014-06-25 | imx6 dtsi: add additional pinctrl groups | Max Krummenacher | |
| 2014-06-25 | mach-types: add the apalis-imx6 machine | Max Krummenacher | |
| 2014-05-05 | imx6q/dl/solo/sololite: set system_rev so the VPU can find its firmware | Troy Kisky | |
| This allow gplay to work. | |||
| 2014-05-05 | imx6qdl-nitrogen6x.dtsi: add tc358743_mipi | Troy Kisky | |
| 2014-04-24 | Add board nitrogen6_mtp | Troy Kisky | |
| 2014-04-24 | Add nitrogen6_max board | Troy Kisky | |
| 2014-04-24 | dma-mapping: increase DEFAULT_DMA_COHERENT_POOL_SIZE ifdef CONFIG_VIDEO_TW68 | Troy Kisky | |
 |
index : linux-toradex.git | |
| Linux kernel for Apalis and Colibri modules | Toradex |
| summaryrefslogtreecommitdiff |