summaryrefslogtreecommitdiff
path: root/drivers/firewire/ohci.c
AgeCommit message (Collapse)Author
2011-10-18firewire: ohci: fix isochronous DMA synchronizationClemens Ladisch
Add the dma_sync_single_* calls necessary to ensure proper cache synchronization for isochronous data buffers on non-coherent architectures. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-10-18firewire: ohci: work around selfID junk due to wrong gap countClemens Ladisch
If a device's firmware initiates a bus reset by setting the IBR bit in PHY register 1 without resetting the gap count field to 63 (and without having sent a PHY configuration packet beforehand), the gap count of this node will remain at the old value after the bus reset and thus be inconsistent with the gap count on all other nodes. The bus manager is supposed to detect the inconsistent gap count values in the self ID packets and correct them by issuing another bus reset. However, if the buggy device happens to be the cycle master, and if it sends a cycle start packet immediately after the bus reset (which is likely after a long bus reset), then the time between the end of the selfID phase and the start of the cycle start packet will be based on the too-small gap count value, so this gap will be too short to be detected as a subaction gap by the other nodes. This means that the cycle start packet will be assumed to be self ID data, and will be stored after the actual self ID quadlets in the self ID buffer. This garbage in the self ID buffer made firewire-core ignore all of the self ID data, and thus prevented the Linux bus manager from correcting the problem. Furthermore, because the bus reset handling was aborted completely, asynchronous transfers would be no longer handled correctly, and fw_run_transaction() would hang until the next bus reset. To fix this, make the detection of inconsistent self IDs more discriminating: If the invalid data in the self ID buffer looks like a cycle start packet, we can assume that the previous data in the buffer is correctly received self ID information, and process it normally. (We inspect only the first quadlet of the cycle start packet, because this value is different enough from any valid self ID quadlet, and many controllers do not store the cycle start packet in five quadlets because they expect self ID data to have an even number of quadlets.) This bug has been observed when a bus-powered DesktopKonnekt6 is switched off with its power button. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-10-09firewire: net: Use posted writesStephan Gatzka
Change memory region to ohci "middle address space". This effectively reduces the number of packets by 50%. [Stefan R.:] This eliminates 1394 ack packets and improved throughput by a few percent in some tests with an S400a connection with and without gap count optimization. Since firewire-net taxes the AR-req DMA unit of a FireWire controller much more than firewire-sbp2 (which uses the middle address space with PCI posted writes too), this commit also changes a related error printk into a ratelimited one as a precaution. Side note: The IPv4-over-1394 drivers of Mac OS X 10.4, Windows XP SP3, and the Thesycon 1394 bus driver for Windows all use the middle address space too. Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-10-09firewire: ohci: optimize TSB41BA3D detectionStefan Richter
Takes less source code and machine code, and less runtime with PHYs other than TSB41BA3D (e.g. TSB81BA3 with device ID 0x831304 which takes one instead of six read_paged_phy_reg now). Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-10-09firewire: ohci: TSB41BA3D support tweaksStefan Richter
Fix: phy_reg_mutex must be held over the write/read_phy_reg pair which gets PHY port status. Only print to the log when a TSB41BA3D was found. By far most TSB82AA2 cards have a TSB81BA3, and firewire-ohci can keep quiet about that. Shorten some strings and comments. Change some whitespace. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-09-16firewire: ohci: Add support for TSB41BA3D phyStephan Gatzka
This patch implements a work around for the Texas Instruments PHY TSB41BA3D. This phy has a bug at least in combination with the TI LLCs TSB82AA2B and TSB12LV26. The selfid coming from the locally connected phy is not propagated into the selfid buffer of the OHCI (see http://www.ti.com/litv/pdf/sllz059 for details). The main idea is to construct the selfid ourselves. Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-09-16firewire: ohci: Move code from the bus reset tasklet into a workqueueStephan Gatzka
Code inside bus_reset_work may now sleep. This is a prerequisite to support a phy from Texas Instruments cleanly. The patch to support this phy will be submitted later. Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-09-16firewire: ohci: add no MSI quirk for O2Micro controllerMing Lei
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 . An O2Micro PCI Express FireWire controller, "FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)" which is a combination device together with an SDHCI controller and some sort of storage controller, misses SBP-2 status writes from an attached FireWire HDD. This problem goes away if MSI is disabled for this FireWire controller. The device reportedly does not require QUIRK_CYCLE_TIMER. Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (amended changelog) Cc: <stable@kernel.org>
2011-08-15Merge branch 'fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firewire: ohci: fix DMA unmapping in an error path firewire: cdev: fix 32 bit userland on 64 bit kernel compat corner cases
2011-08-12firewire: ohci: fix DMA unmapping in an error pathStefan Richter
If request_irq failed, we would pass wrong arguments to dma_free_coherent. https://bugzilla.redhat.com/show_bug.cgi?id=728185 Reported-by: Mads Kiilerich Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-07-22Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firewire: document the sysfs ABIs firewire: cdev: ABI documentation enhancements firewire: cdev: prevent race between first get_info ioctl and bus reset event queuing firewire: cdev: return -ENOTTY for unimplemented ioctls, not -EINVAL firewire: ohci: skip soft reset retries after card ejection firewire: ohci: fix PHY reg access after card ejection firewire: ohci: add a comment on PHY reg access serialization firewire: ohci: reduce potential context_stop latency firewire: ohci: remove superfluous posted write flushes firewire: net: replacing deprecated __attribute__((packed)) with __packed
2011-07-10firewire: ohci: do not bind to Pinnacle cards, avert panicStefan Richter
When firewire-ohci is bound to a Pinnacle MovieBoard, eventually a "Register access failure" is logged and an interrupt storm or a kernel panic happens. https://bugzilla.kernel.org/show_bug.cgi?id=36622 Until this is sorted out (if that is going to succeed at all), let's just prevent firewire-ohci from touching these devices. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: <stable@kernel.org>
2011-07-09firewire: ohci: skip soft reset retries after card ejectionStefan Richter
The software reset in firewire-ohci's pci_remove does not have a great prospect of success if the card was already physically removed at this point. So let's skip the 500 ms that were spent in retries here. Also, replace a defined constant by its open-coded value. This is not a constant from a specification but an arbitrarily chosen retry limit. It was only used in this single place. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-07-09firewire: ohci: fix PHY reg access after card ejectionStefan Richter
Detect and handle ejection of FireWire CardBus cards in PHY register accesses: - The last attempt of firewire-core to reset the bus during shutdown caused a spurious "firewire_ohci: failed to write phy reg" error message in the log. Skip this message as well as the prior retry loop that needlessly took 100 milliseconds. - In the unlikely case that a PHY register was read right after card ejection, a bogus value was obtained and possibly acted upon. Instead, fail the read attempt. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-07-09firewire: ohci: add a comment on PHY reg access serializationStefan Richter
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-07-09firewire: ohci: reduce potential context_stop latencyStefan Richter
Stopping an isochronous reception DMA context takes two loop iterations in context_stop on several controllers (JMicron, NEC, VIA). But there is no extra delay necessary between these two reg_read trials; the MMIO reads themselves are slow enough. Hence bring back the behavior from before commit dd6254e5c0efe01ad255188898cb3dadf98cb56d "firewire: ohci: remove superfluous posted write flushes" on these controllers by means of an "if (i)" condition. Isochronous context stop is performed in preemptible contexts (and only rarely), hence this change is of little impact. (Besides, Agere and TI controllers always, or almost always, have the context stopped already at the first ContextControl read.) More important is asynchronous transmit context stop, which is performed while local interrupts are disabled (on the two AT DMAs in bus_reset_tasklet, i.e. after a self-ID-complete event). In my experience with several controllers, tested with a usermode AT-request transmitter as well as with FTP transmission over firewire-net, the AT contexts were luckily already stopped at the first ContextControl read, i.e. never required another MMIO read let alone mdelay. A possible explanation for this is that the controllers which I tested perhaps stop AT DMA before they perform the self-ID reception DMA. But we cannot be sure about that and should keep the interrupts-disabled busy loop as short as possible. Hence, query the ContextControl register in 1000 udelay(10) intervals instead of 10 udelay(1000) intervals. I understand from an estimation by Clemens Ladisch that stopping a busy DMA context should take microseconds or at worst tens of microseconds, not milliseconds. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-06-02firewire: ohci: remove superfluous posted write flushesClemens Ladisch
The call to flush_writes() in context_stop() is superfluous because another register read is done immediately afterwards. The call to flush_writes() in ar_context_run() does not need to be done individually for each AR context, so move it to ohci_enable(). This also makes ohci_enable() clearer because it no longer depends on a side effect of ar_context_run() to flush its own register writes. Finally, the setting of a context's wake bit does not need to be flushed because neither the driver logic nor the API require the CPU to wait for this action. This removes the last MMIO reads from the packet queueing code paths. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-05-10firewire: optimize iso queueing by setting wake only after the last packetClemens Ladisch
When queueing iso packets, the run time is dominated by the two MMIO accesses that set the DMA context's wake bit. Because most drivers submit packets in batches, we can save much time by removing all but the last wakeup. The internal kernel API is changed to require a call to fw_iso_context_queue_flush() after a batch of queued packets. The user space API does not change, so one call to FW_CDEV_IOC_QUEUE_ISO must specify multiple packets to take advantage of this optimization. In my measurements, this patch reduces the time needed to queue fifty skip packets from userspace to one sixth on a 2.5 GHz CPU, or to one third at 800 MHz. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-05-10Merge tag 'v2.6.39-rc7'Stefan Richter
in order to pull in changes in drivers/media/dvb/firewire/ and sound/firewire/.
2011-05-02firewire: Fix for broken configrom updates in quick successionB.J. Buchalter
Current implementation of ohci_set_config_rom() uses a deferred bus reset via fw_schedule_bus_reset(). If clients add multiple unit descriptors to the config_rom in quick succession, the deferred bus reset may not have fired before succeeding update requests have come in. This can lead to an incorrect partial update of the config_rom for both addition and removal of config_rom descriptors, as the ohci_set_config_rom() routine will return -EBUSY if a previous pending update has not been completed yet; the requested update just gets dropped on the floor. This patch recognizes that the "in-flight" update can be modified until it has been processed by the bus-reset, and the locking in the bus_reset_tasklet ensures that the update is done atomically with respect to modifications made by ohci_set_config_rom(). The -EBUSY error case is simply removed. [Stefan R: The bug always existed at least theoretically. But it became easy to trigger since 2.6.36 commit 02d37bed188c "firewire: core: integrate software-forced bus resets with bus management" which introduced long mandatory delays between janitorial bus resets.] Signed-off-by: Benjamin Buchalter <bj@mhlabs.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (trivial style changes) Cc: <stable@kernel.org> # 2.6.36.y and newer
2011-04-19firewire: ohci: optimize find_branch_descriptor()Clemens Ladisch
When z==2, the condition "key == 2" is superfluous because it cannot occur without "b == 3", as a descriptor with b!=3 and key==2 would be an OUTPUT_MORE_IMMEDIATE descriptor which cannot be used alone. Also remove magic numbers and needless computations on the b field. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-04-19firewire: ohci: avoid separate DMA mapping for small AT payloadsClemens Ladisch
For AT packet payloads of up to eight bytes, we have enough unused space in the DMA descriptors list so that we can put a copy of the payload there and thus avoid having to create a separate streaming DMA mapping for the payload buffer. In a CPU-bound microbenchmark that just sends 8-byte packets, bandwidth was measured to increase by 5.7 %, from 1009 KB/s to 1067 KB/s. In practice, the only performance-sensitive usage of small asynchronous packets is the SBP-2 driver's write to the ORB_POINTER register during SCSI command submission. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-04-19firewire: ohci: do not start DMA contexts before link is enabledClemens Ladisch
OHCI 1.1 5.7.3 not only forbids enabling or starting any DMA contexts before the linkEnable bit is set, but also explicitly warns of undefined behaviour if this order is violated. Don't violate it then. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-03-14firewire: ohci: Misleading kfree in ohci.c::pci_probe/removeOleg Drokin
It seems drivers/firewire/ohci.c is making some optimistic assumptions about struct fw_ohci and that member "card" will always remain the first member of the struct. Plus it's probably going to confuse a lot of static code analyzers too. So I wonder if there is a good reason not to free the ohci struct just like it was allocated instead of the tricky &ohci->card way? Signed-off-by: Oleg Drokin <green@linuxhacker.ru> It is perhaps just a rudiment from before mainline submission of the driver. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-03-14firewire: ohci: omit IntEvent.busReset check rom AT queueingStefan Richter
Since commit 82b662dc4102 "flush AT contexts after bus reset for OHCI 1.2", the driver takes care of any AT packets that were enqueued during a bus reset phase. The check from commit 76f73ca1b291 is therefore no longer necessary and the MMIO read can be avoided. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-02-26firewire: ohci: prevent starting of iso contexts with empty queueClemens Ladisch
If a misguided program tried to start an isochronous context before it has queued any packets, the call would appear to succeed, but the context would not actually go into the running state, and the OHCI controller would then raise an unrecoverableError interrupt because the first Z value is zero and thus invalid. The driver logs such errors, but there is no mechanism to report this back to the program. Add an explicit check so that this error can be returned synchronously. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-02-26firewire: ohci: prevent iso completion callbacks after context stopClemens Ladisch
To prevent the iso packet callback from being called after fw_iso_context_stop() has returned, make sure that the context's tasklet has finished executing before that. This fixes access-after-free bugs that have so far been observed only in the upcoming snd-firewire-speakers driver, but can theoretically also happen in the firedtv driver. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-01-23firewire: ohci: log dead DMA contextsClemens Ladisch
When a DMA context goes into the dead state (and the controller thus stops working correctly), logging this error and the controller's error code might be helpful for debugging. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-01-13firewire: ohci: fix compilation on arches without PAGE_KERNEL_ROClemens Ladisch
PAGE_KERNEL_RO is not available on all architectures, so its use in the new AR code broke compilation on sparc64. Because the read-only mapping was just a debugging aid, just use PAGE_KERNEL instead. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> James Bottomley wrote: > On Thu, 2011-01-13 at 08:27 +0100, Clemens Ladisch wrote: >> firewire: ohci: fix compilation on arches without PAGE_KERNEL_RO, e.g. sparc >> >> PAGE_KERNEL_RO is not available on all architectures, so its use in the >> new AR code broke compilation on sparc64. >> >> Because the R/O mapping is only used to catch drivers that try to write >> to the reception buffer and not actually required for correct operation, >> we can just use a normal PAGE_KERNEL mapping where _RO is not available. [...] >> +/* >> + * For archs where PAGE_KERNEL_RO is not supported; >> + * mapping the AR buffers readonly for the CPU is just a debugging aid. >> + */ >> +#ifndef PAGE_KERNEL_RO >> +#define PAGE_KERNEL_RO PAGE_KERNEL >> +#endif > > This might cause interesting issues on sparc64 if it ever acquired a > PAGE_KERNEL_RO. Sparc64 has extern pgprot_t for it's PAGE_KERNEL types > rather than #defines, so the #ifdef check wouldn't see this. > > I think either PAGE_PROT_RO becomes part of our arch API (so all > architectures are forced to add it), or, if it's not part of the API, > ohci isn't entitled to use it. The latter seems simplest since you have > no real use for write protection anyway. Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-01-04firewire: ohci: consolidate context status flagsStefan Richter
"firewire: ohci: restart iso DMA contexts on resume from low power mode" added the flag struct context.active and "firewire: ohci: cache the context run bit" added struct context.running. These flags contain the same information; combine them. Also, normalize whitespace in pci_resume(). Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-01-04firewire: ohci: cache the context run bitClemens Ladisch
The DMA context run control bit is entirely controlled by software, so it is safe to cache it. This allows the driver to avoid doing an additional MMIO read when queueing an AT packet. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2011-01-04firewire: ohci: flush AT contexts after bus reset - addendumStefan Richter
Add comments - on why bus_reset_tasklet flushes AT queues, - that commit 76f73ca1b291 can possibly be reverted now. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Acked-by: Jarod Wilson <jarod@redhat.com>
2011-01-03firewire: ohci: flush AT contexts after bus reset for OHCI 1.2Clemens Ladisch
The OHCI 1.2 (draft) specification, clause 7.2.3.3, allows and recommends that, after a bus reset, the controller does not flush all the packets in the AT queues. Therefore, the driver has to do this itself. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: ohci: restart iso DMA contexts on resume from low power modeMaxim Levitsky
Restore iso channels DMA so that iso channels could continue to work after resume from RAM/disk. Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: ohci: restore GUID on resume.Maxim Levitsky
Some lousy BIOSes, e.g. my Aspire 5720 BIOS forget to restore the GUID register on resume from RAM. Fix that by setting it to the last value that was read from it. Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: ohci: use common buffer for self IDs and AR descriptorsClemens Ladisch
The buffers used for the selfIDs packets and the AR request and response descriptors end up using three pages because dma_alloc_coherent() allocates at least one page per call. However, these data structures would all fit into 4 KB, so we can save space by using a common buffer for them. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: ohci: optimize iso context checks in the interrupt handlerClemens Ladisch
When the isochRx/isochTx bit is clear, we do not need to read the corresponding iso interrupt event register. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: make PHY packet header format consistentClemens Ladisch
Change the header of PHY packets to be sent to include a pseudo transaction code. This makes the header consistent with that of received PHY packets, and allows at_context_queue_packet() and log_ar_at_event() to see the packet type directly instead of having to deduce it from the header length or even from the header contents. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: ohci: properly clear posted write errorsClemens Ladisch
To remove the error information from the controller's queue and to allow more posted writes, the driver has to read the failed posted write address before clearing the postedWriteErr interrupt bit. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> (Stefan R:) The spec is somewhat fuzzy about the actual requirements. To err on the safe side, let's do these two read accesses. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: ohci: flush MMIO writes in the interrupt handlerClemens Ladisch
Make sure that interrupt event clear bit writes are executed before the interrupt handler returns. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: ohci: fix AT context initialization error handlingClemens Ladisch
Add proper error handling for the context_init() calls. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-13firewire: ohci: Asynchronous Reception rewriteClemens Ladisch
Move the AR DMA descriptors out of the buffer pages, and map the buffer pages linearly into the kernel's address space. This allows the driver to ignore any page boundaries in the DMA data and thus to avoid any copying around of packet payloads. This fixes the bug where S800 packets that are so big (> 4080 bytes) that they can be split over three pages were not handled correctly. Due to the changed algorithm, we can now use arbitrarily many buffer pages, which improves performance because the controller can more easily unload its DMA FIFO. Furthermore, using streaming DMA mappings should improve perfomance on architectures where coherent DMA mappings are not cacheable. Even on other architectures, the caching behaviour should be improved slightly because the CPU no longer writes to the buffer pages. v2: Detect the last filled buffer page by searching the descriptor's residual count value fields in order (like in the old code), instead of going backwards through the transfer status fields; it looks as if some controllers do not set the latter correctly. v3: Fix an old resume bug that would now make the handler run into a BUG_ON, and replace that check with more useful error handling. Increase the buffer size for better performance with non-TI chips. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Maxim Levitsky writes: Works almost perfectly. I can still see RCODE_BUSY errors sometimes, not very often though. 64K here eliminates these errors completely. This is most likely due to nouveau drivers and lowest perf level I use to lower card temperature. That increases latencies too much I think. Besides that the IO is just perfect. Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-12-12firewire: ohci: fix regression with Agere FW643 rev 06, disable MSIStefan Richter
Agere FW643 rev 06, listed as "11c1:5901 (rev 06) (prog-if 10 [OHCI])", produced SBP-2 I/O errors since kernel 2.6.36. Disabling MSI fixes it. Since MSI work on Agere FW643-E (same vendor and device ID, but rev 07), introduce a device revision field into firewire-ohci's quirks list so that different quirks can be defined for older and newer revisions. Reported-by: Jonathan Isom <jeisom@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: <stable@kernel.org> # 2.6.36.y
2010-12-12firewire: ohci: fix regression with VIA VT6315, disable MSIStefan Richter
"VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403]" does not generate any interrupts if Message Signaled Interrupts were enabled. This is a regression since kernel 2.6.36 in which MSI support was added to firewire-ohci. Hence blacklist MSI on all VIA controllers. Reported-by: Robin Cook <rcook@wyrms.net> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: <stable@kernel.org> # 2.6.36.y
2010-10-30firewire: ohci: fix race when reading count in AR descriptorClemens Ladisch
If the controller is storing a split packet and therefore changing d->res_count to zero between the two reads by the driver, we end up with an end pointer that is not at a packet boundary, and therefore overflow the buffer when handling the split packet. To fix this, read the field once, atomically. The compiler usually merges the two reads anyway, but for correctness, we have to enforce it. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-10-30firewire: ohci: avoid reallocation of AR buffersClemens Ladisch
Freeing an AR buffer page just to allocate a new page immediately afterwards is not only a pointless effort but also dangerous because the allocation can fail, which would result in an oops later. Split ar_context_add_page() into two functions so that we can reuse the old page directly. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-10-30firewire: ohci: fix race in AR split packet handlingClemens Ladisch
When handling an AR buffer that has been completely filled, we assumed that its descriptor will not be read by the controller and can be overwritten. However, when the last received packet happens to end at the end of the buffer, the controller might not yet have moved on to the next buffer and might read the branch address later. If we overwrite and free the page before that, the DMA context will either go dead because of an invalid Z value, or go off into some random memory. To fix this, ensure that the descriptor does not get overwritten by using only the actual buffer instead of the entire page for reassembling the split packet. Furthermore, to avoid freeing the page too early, move on to the next buffer only when some data in it guarantees that the controller has moved on. This should eliminate the remaining firewire-net problems. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: 2.6.22-2.6.36 <stable@kernel.org> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-10-30firewire: ohci: fix buffer overflow in AR split packet handlingClemens Ladisch
When the controller had to split a received asynchronous packet into two buffers, the driver tries to reassemble it by copying both parts into the first page. However, if size + rest > PAGE_SIZE, i.e., if the yet unhandled packets before the split packet, the split packet itself, and any received packets after the split packet are together larger than one page, then the memory after the first page would get overwritten. To fix this, do not try to copy the data of all unhandled packets at once, but copy the possibly needed data every time when handling a packet. This gets rid of most of the infamous crashes and data corruptions when using firewire-net. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: 2.6.22-2.6.36 <stable@kernel.org> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (cast PAGE_SIZE to size_t)
2010-10-17firewire: ohci: fix TI TSB82AA2 regression since 2.6.35Stefan Richter
Revert commit 54672386ccf36ffa21d1de8e75624af83f9b0eeb "firewire: ohci: fix up configuration of TI chips". It caused massive slow-down and data corruption with a TSB82AA2 based StarTech EC1394B2 ExpressCard and FireWire 800 harddisks. https://bugs.launchpad.net/ubuntu/+source/linux/+bug/657081 http://thread.gmane.org/gmane.linux.kernel.firewire.user/4013 The fact that some card EEPROMs do not program these enhancements may be related to TSB81BA3 phy chip errata, if not to bugs of TSB82AA2 itself. We could re-add these configuration steps, but only conditional on a whitelist of cards on which these enhancements bring a proven positive effect. Reported-and-tested-by: Eric Shattow <lucent@gmail.com> Cc: Clemens Ladisch <clemens@ladisch.de> Cc: <stable@kernel.org> 2.6.35 Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-09-08firewire: ohci: activate cycle timer register quirk on Ricoh chipsHeikki Lindholm
The Ricoh FireWire controllers appear to have the non-atomic cycle timer register access bug, so, activate the driver workaround by default. The behaviour was observed on: Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] and Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (rev 04). Signed-off-by: Heikki Lindholm <holin@iki.fi> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>