| Age | Commit message (Collapse) | Author |
|---|
|
The following commit renames irq_gc_ack() to irq_gc_ack_set_bit(),
and makes gpio-mxc and gpio-mxs fail to build.
659fb32d1b67476f4ade25e9ea0e2642a5b9c4b5
genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
The patch fixed a couple of typo of comma to semicolon.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The patch adds device tree probe support for gpio-mxc driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes
platform_device_id to distinguish the different gpio types, IMX1_GPIO
on i.mx1, IMX21_GPIO on i.mx21 and i.mx27, IMX31_GPIO on all other
i.mx SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The bgpio_init() function does not initialise the shadow register for
the GPIO direction register. Thus, when configuring the first GPIO with
gpio_set_direction() all other GPIOs of the same bank will be
configured as inputs. Since the bgpio layer cannot know whether the
register is readable, the initialisation should be done by the caller
of bgpio_init().
Also, the 'data' shadow variable that is used inside basic_mmio_gpio
to cache the current value of the GPIO_DR register is initialised from
the GPIO_PSR register within bgpio_init(). Thus when setting the
output value of a certain GPIO, the other GPIO outputs of the same
bank will be set or cleared depending on the pin state of the GPIO
inputs during bgpio_init().
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
When calling gpio_get_value, the gpio number other than bit offset
should be passed as the argument.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The patch converts gpio-mxc driver to use generic irq chip.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The gpio-mxc controller complies with basic_mmio_gpio library. The
patch convert the driver to use the library.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.
* Add a list to save all mx2 ports references, so that
mx2_gpio_irq_handler can walk through all interrupt status
registers
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxc_gpio_init into mxc_gpio_probe function
* Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
be public at all, and also make some other cleanup on
plat-mxc/include/mach/gpio.h at the same time
And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the plat-mxc driver. Follow up
patches will clean it up and make it a fine upstanding gpio driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
