| Age | Commit message (Collapse) | Author |
|---|
|
These resources are managed by devres, and should not be explicitly
released.
Signed-off-by: Michael Auchter <a@phire.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It appears that input sensing bit might be reset during
suspend/resume. Set input sensing again for all requested gpios
in resume
Tested-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Zynq GPIO interrupt handling code as two main issues:
1) It does not support IRQF_ONESHOT interrupt since it uses handle_simple_irq()
for the interrupt handler. handle_simple_irq() does not do masking and unmasking
of the IRQ that is required for this chip to be able to support IRQF_ONESHOT
IRQs, causing the CPU to lock up in a interrupt storm if such a interrupt is
requested.
2) Interrupts are acked after the primary interrupt handlers for all asserted
interrupts in a bank have been called. For edge triggered interrupt this is to
late and may cause a interrupt to be missed. For level triggered oneshot
interrupts this is to early and causes the interrupt handler to run twice per
interrupt.
This patch addresses the issue by updating the driver to use the correct IRQ
chip handler functions that are appropriate for this kind of IRQ controller.
The following diagram gives an overview of how the interrupt detection circuit
works, it is not necessarily a accurate depiction of the real hardware though.
INT_POL/INT_ON_ANY
|
| +---+ INT_STATUS
`-| | |
| E |-. |
,---| | \ |\ +----+ | +---+
| +---+ `----| | ,-------|S | ,*--| |
GPIO_IN -* | |- | Q|- | & |-- IRQ_OUT
| +---+ ,-----| | ,-|R | ,o| |
`---| | / |/ | +----+ | +---+
| = |- | | |
,-| | INT_TYPE ACK INT_MASK
| +---+
|
INT_POL
GPIO_IN is the raw signal level connected to the hardware pin. This signal is
routed to a edge detector and to a level detector. The edge detector can be
configured to either detect a rising or falling edge or both edges. The level
detector can detect either a level high or level low event. Depending on the
setting of the INT_TYPE register either the edge or level event will be
propagated to the INT_STATUS register. As long as a interrupt condition is
detected the INT_STATUS register will be set to 1. It can be cleared to 0 if
(and only if) the interrupt condition is no longer detected and software
acknowledges the interrupt by writing a 1 to the address of the INT_STATUS
register. There is also the INT_MASK register which can be used to disable the
propagation of the INT_STATUS signal to the upstream IRQ controller. What is
important to note is that the interrupt detection logic itself can not be
disabled, only the propagation of the INT_STATUS register can be delayed. This
means that for level type interrupts the interrupt must only be acknowledged
after the interrupt source has been cleared otherwise it will stay asserted and
the interrupt handler will be run a second time. For IRQF_ONESHOT interrupts
this means that the IRQ must only be acknowledged after the threaded interrupt
has finished running. If a second interrupt comes in between handling the first
interrupt and acknowledging it the external interrupt will be asserted, which
means trying to acknowledge the first interrupt will not clear the INT_STATUS
register and the interrupt handler will be run a second time when the IRQ is
unmasked, so no interrupts will be lost. The handle_fasteoi_irq() handler in
combination with the IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED flags will
have the desired behavior. For edge triggered interrupts a slightly different
strategy is necessary. For edge triggered interrupts the interrupt condition is
only true when the edge itself is detected, this means this is the only time the
INT_STATUS register is set, acknowledging the interrupt any time after that will
clear the INT_STATUS register until the next interrupt happens. This means in
order to not loose any interrupts the interrupt needs to be acknowledged before
running the interrupt handler. If a second interrupt occurs after the first
interrupt handler has finished but before the interrupt is unmasked the
INT_STATUS register will be re-asserted and the interrupt handler runs a second
time once the interrupt is unmasked. This means with this flow handling strategy
no interrupts are lost for edge triggered interrupts. The handle_level_irq()
handler will have the desired behavior. (Note: The handle_edge_irq() only needs
to be used for edge triggered interrupts where the controller stops detecting
the interrupt event when the interrupt is masked, for this controller the
detection logic still works, while only the propagation is delayed when the
interrupt is masked.)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO update from Linus Walleij:
"This is the bulk of GPIO changes for the v3.17 development cycle, and
this time we got a lot of action going on and it will continue:
- The core GPIO library implementation has been split up in three
different files:
- gpiolib.c for the latest and greatest and shiny GPIO library code
using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API that we are
phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are not entirely
happy with, but has to live on for ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We should have
had the flags there from the beginning it seems, now we need to
clean up the mess. There is a plan on how to move forward here
devised by Alexandre Courbot and Mark Brown
- Split off a special <linux/gpio/machine.h> header for the board
gpio table registration, as per example from the regulator
subsystem
- Start to kill off the return value from gpiochip_remove() by
removing the __must_check attribute and removing all checks inside
the drivers/gpio directory. The rationale is: well what were we
supposed to do if there is an error code? Not much: print an error
message. And gpiolib already does that. So make this function
return void eventually
- Some cleanups of hairy gpiolib code, make some functions not to be
used outside the library private and make sure they are not
exported, remove gpiod_lock/unlock_as_irq() as the existing
function is for driver-internal use and fine as it is, delete
gpio_ensure_requested() as it is not meaningful anymore
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one() function
calls, which is logical since this is already supported when
referencing GPIOs from e.g. device trees
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use the gpiolib
irqchip helpers cutting down on GPIO irqchip boilerplate a bit more
- New driver for the Zynq GPIO block
- The usual incremental improvements around a bunch of drivers
- Janitorial syntactic and semantic cleanups by Jingoo Han, and
Rickard Strandqvist especially"
* tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (37 commits)
MAINTAINERS: update GPIO include files
gpio: add missing includes in machine.h
gpio: add flags argument to gpiod_get*() functions
MAINTAINERS: Update Samsung pin control entry
gpio / ACPI: Move event handling registration to gpiolib irqchip helpers
gpio: lynxpoint: Convert to use gpiolib irqchip
gpio: split gpiod board registration into machine header
gpio: remove gpio_ensure_requested()
gpio: remove useless check in gpiolib_sysfs_init()
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
gpio: move gpio_ensure_requested() into legacy C file
gpio: remove gpiod_lock/unlock_as_irq()
gpio: make gpiochip_get_desc() gpiolib-private
gpio: simplify gpiochip_export()
gpio: remove export of private of_get_named_gpio_flags()
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
gpio: zynq: Clear pending interrupt when enabling a IRQ
gpio: drop retval check enforcing from gpiochip_remove()
gpio: remove all usage of gpio_remove retval in driver/gpio
devicetree: Add Zynq GPIO devicetree bindings documentation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
|
|
The huge majority of GPIOs have their direction and initial value set
right after being obtained by one of the gpiod_get() functions. The
integer GPIO API had gpio_request_one() that took a convenience flags
parameter allowing to specify an direction and value applied to the
returned GPIO. This feature greatly simplifies client code and ensures
errors are always handled properly.
A similar feature has been requested for the gpiod API. Since setting
the direction of a GPIO is so often the very next action done after
obtaining its descriptor, we prefer to extend the existing functions
instead of introducing new functions that would raise the
number of gpiod getters to 16 (!).
The drawback of this approach is that all gpiod clients need to be
updated. To limit the pain, temporary macros are introduced that allow
gpiod_get*() to be called with or without the extra flags argument. They
will be removed once all consumer code has been updated.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since now we have irqchip helpers that the GPIO chip drivers are supposed
to use if possible, we can move the registration of ACPI events to happen
in these helpers. This seems to be more natural place and might encourage
GPIO chip driver writers to take advantage of the irqchip helpers.
We make the functions available to GPIO chip drivers via private gpiolib.h,
just in case generic irqchip helpers are not suitable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of open-coding irqchip handling in the driver we can take advantage
of the new irqchip helpers provided by the gpiolib core.
While doing this we also make sure that we call gpiochip_irqchip_add()
after the gpiochip itself is registered as required.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As per example from the regulator subsystem: put all defines and
functions related to registering board info for GPIO descriptors
into a separate <linux/gpio/machine.h> header.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
* cleanup/gpio-header-removal:
ARM: delete old reference to ARM_GPIOLIB_COMPLEX
ARM: kill CONFIG_NEED_MACH_GPIO_H
ARM: mach-s5p: get rid of all <mach/gpio.h> headers
ARM: s5p: cut the custom ARCH_NR_GPIOS definition
This resolves a massive amount of conflicts between the
mach/gpio.h removal and the s5p platform removal.
Almost all changes are trivial, as both sides remove
stuff.
Conflicts:
arch/arm/Kconfig
arch/arm/mach-s5p64x0/common.c
arch/arm/mach-s5p64x0/dev-audio.c
arch/arm/mach-s5p64x0/include/mach/gpio-samsung.h
arch/arm/mach-s5p64x0/mach-smdk6440.c
arch/arm/mach-s5p64x0/mach-smdk6450.c
arch/arm/mach-s5p64x0/setup-fb-24bpp.c
arch/arm/mach-s5p64x0/setup-i2c0.c
arch/arm/mach-s5p64x0/setup-i2c1.c
arch/arm/mach-s5p64x0/setup-sdhci-gpio.c
arch/arm/mach-s5p64x0/setup-spi.c
arch/arm/mach-s5pc100/dev-audio.c
arch/arm/mach-s5pc100/include/mach/gpio-samsung.h
arch/arm/mach-s5pc100/mach-smdkc100.c
arch/arm/mach-s5pc100/setup-fb-24bpp.c
arch/arm/mach-s5pc100/setup-i2c0.c
arch/arm/mach-s5pc100/setup-i2c1.c
arch/arm/mach-s5pc100/setup-ide.c
arch/arm/mach-s5pc100/setup-keypad.c
arch/arm/mach-s5pc100/setup-sdhci-gpio.c
arch/arm/mach-s5pc100/setup-spi.c
arch/arm/mach-s5pv210/dev-audio.c
arch/arm/mach-s5pv210/include/mach/gpio-samsung.h
arch/arm/mach-s5pv210/mach-aquila.c
arch/arm/mach-s5pv210/mach-goni.c
arch/arm/mach-s5pv210/mach-smdkv210.c
arch/arm/mach-s5pv210/setup-fb-24bpp.c
arch/arm/mach-s5pv210/setup-fimc.c
arch/arm/mach-s5pv210/setup-i2c0.c
arch/arm/mach-s5pv210/setup-i2c1.c
arch/arm/mach-s5pv210/setup-i2c2.c
arch/arm/mach-s5pv210/setup-ide.c
arch/arm/mach-s5pv210/setup-keypad.c
arch/arm/mach-s5pv210/setup-sdhci-gpio.c
arch/arm/mach-s5pv210/setup-spi.c
arch/arm/plat-samsung/Kconfig
arch/arm/plat-samsung/s5p-irq-eint.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung S5PV210 DT support for v3.17" from Kukjin Kim:
- support common clock framework for s5pv210 clock
- add generic PHY driver on s5pv210 to support it via DT
- add dt support for s5pv210-goni, smdkc110, smdkv210 and torbreck boards
- remove board files from mach-s5pv210 and unused codes
- enable multiplatform for s5pv210
* tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: samsung: s5pv210: Remove legacy board support
ARM: SAMSUNG: Remove remaining legacy code
gpio: samsung: Remove legacy support of S5PV210
ARM: S5PV210: Enable multi-platform build support
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: S5PV210: Register cpufreq platform device
ARM: S5PV210: move debug-macro.S into the common space
ARM: S5PV210: Untie PM support from legacy code
ARM: S5PV210: Remove support for board files
ARM: dts: Add Device tree for s5pc110/s5pv210 boards
ARM: dts: Add Device tree for s5pv210 SoC
ARM: S5PV210: Add board file for boot using Device Tree
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: SAMSUNG: Remove legacy clock code
serial: samsung: Remove support for legacy clock code
cpufreq: s3c24xx: Remove some dead code
ARM: S5PV210: Migrate clock handling to Common Clock Framework
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
'v3.16-rc6' into next/soc
The following samsung branches are based on these cleanups,
which are already in mainline before this branch gets pulled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
gpio_ensure_requested() has been introduced in Feb. 2008 by commit
d2876d08d86f2 to force users of the GPIO API to explicitly request GPIOs
before using them.
Hopefully by now all GPIOs are correctly requested and this extra check
can be omitted ; in any case the GPIO maintainers won't feel bad if
machines start failing after 6 years of warnings.
This patch removes that function from the dark ages.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
An iterator variable cannot be NULL in its loop.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Both functions were introduced to let gpio drivers request their own
gpio pins. Without exporting the functions, this can however only be
used by gpio drivers built into the kernel.
Secondary impact is that the functions can not currently be used by
platform initialization code associated with the gpio-pca953x driver.
This code permits auto-export of gpio pins through platform data, but
if this functionality is used, the module can no longer be unloaded due
to the problem solved with the introduction of gpiochip_request_own_desc
and gpiochip_free_own_desc.
Export both function so they can be used from modules and from
platform initialization code.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes for the v3.16 series. Sorry that
some of these arrive late, the summer heat in Sweden makes me slow.
- an IRQ handling fix for the STi driver, also for stable
- another IRQ fix for the RCAR GPIO driver
- a MAINTAINERS entry"
* tag 'pinctrl-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
gpio: rcar: Add support for DT IRQ flags
MAINTAINERS: Add entry for the Renesas pin controller driver
pinctrl: st: Fix irqmux handler
|
|
gpio_ensure_requested() only makes sense when using the integer-based
GPIO API, so make sure it is called from there instead of the gpiod
API which we know cannot be called with a non-requested GPIO anyway.
The uses of gpio_ensure_requested() in the gpiod API were kind of
out-of-place anyway, so putting them in gpio-legacy.c helps clearing the
code.
Actually, considering the time this ensure_requested mechanism has been
around, maybe we should just turn this patch into "remove
gpio_ensure_requested()" if we know for sure that no user depend on it
anymore?
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gpio_lock/unlock_as_irq() are working with (chip, offset) arguments and
are thus not using the old integer namespace. Therefore, there is no
reason to have gpiod variants of these functions working with
descriptors, especially since the (chip, offset) tuple is more suitable
to the users of these functions (GPIO drivers, whereas GPIO descriptors
are targeted at GPIO consumers).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As GPIO descriptors are not going to remain unique anymore, having this
function public is not safe. Restrain its use to gpiolib since we have
no user outside of it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For some reason gpiochip_export() would invalidate all the descriptors
of a chip if exporting it to sysfs failed. This does not appear as
necessary. Remove that part of the code.
While we are at it, add a note about the non-safety of temporarily
releasing a spinlock in the middle of the loop that protects its
iterator, and explain why this is done.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
of_get_named_gpio_flags() has been made gpiolib-private by commit
f01d907582, but its EXPORT statement has not been removed. Fix this.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio include file and the gpio documentation declare and document
GPIOF_ACTIVE_LOW as one of the flags to be passed to gpio_request_one
and related functions. However, the flag is not evaluated or used.
This can cause problems in at least two areas: First, the same API can
be used to auto-export pins to user space. The missing support for
GPIOF_ACTIVE_LOW results in unexpected behavior for such auto-exported
pins. Second, the requested gpio pin can be convered for use by
gpiod functions with gpio_to_desc(). While gpio API functions do not
support GPIOF_ACTIVE_LOW, gpiod functions do, which again results in
unexpected behavior.
Check the flag in gpio_request_one and set the gpio internal flag
FLAG_ACTIVE_LOW if it is set to address those problems.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Zynq GPIO controller does not disable the interrupt detection when the
interrupt is masked and only disables the propagation of the interrupt. This
means when the controller detects an interrupt condition while the interrupt is
logically disabled (and masked) it will propagate the recorded interrupt event
once the interrupt is enabled. This will cause the interrupt consumer to see
spurious interrupts to prevent this first make sure that the interrupt is not
asserted and then enable it.
E.g. when a interrupt is requested with request_irq() it will be configured
according to the requested type (edge/level triggered, etc.) after that it will
be enabled. But the detection circuit might have already registered a false
interrupt before the interrupt type was correctly configured and once the
interrupt is unmasked this false interrupt will be propagated and the interrupt
handler for the just request interrupt will called.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: abdoulaye berthe <berthe.ab@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO support of S5PV210 SoC is now fully handled by pinctrl-samsung
driver making the old code in gpio-samsung driver unused. This patch
removes it which will also let us remove more code from arch subtree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into next/cleanup
This is a purge of all things <mach/gpio.h>, now I never
want to see it again.
- Remove the need for <mach/gpio.h> from S5P
- Kill CONFIG_NEED_MACH_GPIO_H
- Kill remnants of ARM_GPIOLIB_COMPLEX
* tag 'gpio-h-purge' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
ARM: delete old reference to ARM_GPIOLIB_COMPLEX
ARM: kill CONFIG_NEED_MACH_GPIO_H
ARM: mach-s5p: get rid of all <mach/gpio.h> headers
ARM: s5p: cut the custom ARCH_NR_GPIOS definition
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The gpio-rcar driver has no IRQ domain OF xlate function and thus
ignores IRQ flags specified in DT. Fix this by using the two-cell xlate
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch removes gpio codes for s5pc100 SoC.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add support for GPIO controller used by Xilinx Zynq.
v3 changes:
- Use linux/gpio/driver.h instead of linux/gpio.h
- Make irq a local variable in probe
v2 changes:
- convert to pm_runtime_force_(suspend|resume)
- add pm_runtime_set_active in probe()
- also (un)prepare clocks when they are dis-/enabled
- add some missing calls to pm_runtime_get()
- use pm_runtime_put() instead of sync variant
- remove gpio chip in driver remove()
- remove redundant type casts
- directly use IO helpers
- use BIT macro to set/clear bits
- migrate to GPIOLIB_IRQCHIP
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Following is the debug output (only a few examples) before and after
the patch.
$ dmesg | grep of_get_named_gpiod_flags
Before:
of_get_named_gpiod_flags: can't parse gpios property
of node '/mmc@12220000[0]'
of_get_named_gpiod_flags exited with status 0
After:
of_get_named_gpiod_flags: can't parse 'wp-gpios' property
of node '/mmc@12220000[0]'
of_get_named_gpiod_flags: parsed 'gpios' property of node
'/gpio-keys/power[0]' - status (0)
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The old integer GPIO interface is, in effect, a privileged user of the
gpiod interface. Reflect this fact further by moving legacy GPIO support
into its own source file. This makes the code clearer and will allow us
to disable legacy GPIO support in the (far) future.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sysfs support is currently entangled within the core GPIO support, while
it should relly just be a (privileged) user of the integer GPIO API.
This patch is a first step towards making the gpiolib code more readable
by splitting it into logical parts.
Move all sysfs support to their own source file, and share static
members of gpiolib that need to be in the private gpiolib.h file. In
the future we will want to put some of them back into gpiolib.c, but this
first patch let us at least identify them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Compiling out GPIO labels results in a space gain so small that it can
hardly be justified. Labels can also be useful for printing debug
messages, so always keep them around.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO OMAP driver didn't have a consistent naming scheme for
all its functions. Some of them had an omap prefix while others
didn't. There are many advantages on having a separate namespace
for driver functions so let's add an "omap" prefix to all of them.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The <linux/irqchip/chained_irq.h> header is already included
when selecting GPIOLIB_IRQCHIP so there is no need to do it
in the driver. This is a left over from commit fb655f5
("gpio: omap: convert driver to use gpiolib irqchip").
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO irqchips assign to the cascaded IRQs their own lock class
in order to avoid warnings about lockdep recursions since that
allow the lockdep core to keep track of things.
Since commit e45d1c80 ("gpio: put GPIO IRQs into their own lock class")
there is no need to do this in a driver if it's using the GPIO
irqchip helpers since gpiolib already assigns a lockdep class.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Removal of null pointer checks that could never happen
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Removal of null pointer checks that could never happen
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The driver was not checking the return value from gpiochip_add()
properly, so add a bail-out check.
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
While it will be clamped to bool by gpiolib, let's make this sane
in the driver as well.
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch removes gpio codes for s5p6440 and s5p6450 SoCs.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
pxa_gpio_probe() has some issues supporting the gpio0 and gpio1
interrupts under device-tree - it never actually sets up the chain
handler to get interrupts on edge detect for GPIO0 and GPIO1.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Unnecessary checking was added during the merge of the gpio branch.
This patch removes the extra unnecessary checking.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This renames all the local <mach/gpio.h> headers in the S5P platforms
to <mach/gpio-samsung.h> indicating a scope local to this platform,
and cuts the implicit inclusion of <mach/gpio.h> from <linux/gpio.h>
by removing the use of NEED_MACH_GPIO_H from all S5P variants.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
drivers/gpio/gpio-crystalcove.c: In function 'crystalcove_gpio_dbg_show':
drivers/gpio/gpio-crystalcove.c:286:3: error: implicit declaration of function 'seq_printf'
seq_printf(s, " gpio-%-2d %s %s %s %s ctlo=%2x,%s %s %s\n",
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
