| Age | Commit message (Collapse) | Author |
|---|
|
If bgpio_map returns NULL then err should always be set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The TCA9539 is almost identical to the PCA9555 and software-compatible
with this driver. It exposes 16 general purpose I/O pins in two 8-bit
configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The function __max730x_remove is called from the remove functions of
drivers/gpio/gpio-max7300.c and drivers/gpio/gpio-max7301.c. In both
cases, the probe function allocates ts using devm_kzalloc. Explicitly
freeing such a value with kfree will cause a double free.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch converts TI OMAP GPIO driver to use generic irq handler
instead of chained IRQ handler. This way OMAP GPIO driver will be
compatible with RT kernel where it will be forced thread IRQ handler
while in non-RT kernel it still will be executed in HW IRQ context.
As part of this change the IRQ wakeup configuration is applied to
GPIO Bank IRQ as it now will be under control of IRQ PM Core during
suspend.
There are also additional benefits:
- on-RT kernel there will be no complains any more about PM runtime usage
in atomic context "BUG: sleeping function called from invalid context";
- GPIO bank IRQs will appear in /proc/interrupts and its usage statistic
will be visible;
- GPIO bank IRQs could be configured through IRQ proc_fs interface and,
as result, could be a part of IRQ balancing process if needed;
- GPIO bank IRQs will be under control of IRQ PM Core during
suspend to RAM.
Disadvantage:
- additional runtime overhed as call chain till
omap_gpio_irq_handler() will be longer now
- necessity to use wa_lock in omap_gpio_irq_handler() to W/A warning
in handle_irq_event_percpu()
WARNING: CPU: 1 PID: 35 at kernel/irq/handle.c:149 handle_irq_event_percpu+0x51c/0x638()
This patch doesn't fully follows recommendations provided by Sebastian
Andrzej Siewior [1], because It's required to go through and check all
GPIO IRQ pin states as fast as possible and pass control to handle_level_irq
or handle_edge_irq. handle_level_irq or handle_edge_irq will perform actions
specific for IRQ triggering type and wakeup corresponding registered
threaded IRQ handler (at least it's expected to be threaded).
IRQs can be lost if handle_nested_irq() will be used, because excecution
time of some pin specific GPIO IRQ handler can be very significant and
require accessing ext. devices (I2C).
Idea of such kind reworking was also discussed in [2].
[1] http://www.spinics.net/lists/linux-omap/msg120665.html
[2] http://www.spinics.net/lists/linux-omap/msg119516.html
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PM runtime API can't be used in atomic contex on -RT even if
it's configured as irqsafe. As result, below error report can
be seen when PM runtime API called from IRQ chip's callbacks
irq_startup/irq_shutdown/irq_set_type, because they are
protected by RAW spinlock:
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 128, pid: 96, name: insmod
3 locks held by insmod/96:
#0: (&dev->mutex){......}, at: [<c04752c8>] __driver_attach+0x54/0xa0
#1: (&dev->mutex){......}, at: [<c04752d4>] __driver_attach+0x60/0xa0
#2: (class){......}, at: [<c00a408c>] __irq_get_desc_lock+0x60/0xa4
irq event stamp: 1834
hardirqs last enabled at (1833): [<c06ab2a4>] _raw_spin_unlock_irqrestore+0x88/0x90
hardirqs last disabled at (1834): [<c06ab068>] _raw_spin_lock_irqsave+0x2c/0x64
softirqs last enabled at (0): [<c003d220>] copy_process.part.52+0x410/0x19d8
softirqs last disabled at (0): [< (null)>] (null)
Preemption disabled at:[< (null)>] (null)
CPU: 1 PID: 96 Comm: insmod Tainted: G W O 4.1.3-rt3-00618-g57e2387-dirty #184
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c00190f4>] (unwind_backtrace) from [<c0014734>] (show_stack+0x20/0x24)
[<c0014734>] (show_stack) from [<c06a62ec>] (dump_stack+0x88/0xdc)
[<c06a62ec>] (dump_stack) from [<c006ca44>] (___might_sleep+0x198/0x2a8)
[<c006ca44>] (___might_sleep) from [<c06ab6d4>] (rt_spin_lock+0x30/0x70)
[<c06ab6d4>] (rt_spin_lock) from [<c04815ac>] (__pm_runtime_resume+0x68/0xa4)
[<c04815ac>] (__pm_runtime_resume) from [<c04123f4>] (omap_gpio_irq_type+0x188/0x1d8)
[<c04123f4>] (omap_gpio_irq_type) from [<c00a64e4>] (__irq_set_trigger+0x68/0x130)
[<c00a64e4>] (__irq_set_trigger) from [<c00a7bc4>] (irq_set_irq_type+0x44/0x6c)
[<c00a7bc4>] (irq_set_irq_type) from [<c00abbf8>] (irq_create_of_mapping+0x120/0x174)
[<c00abbf8>] (irq_create_of_mapping) from [<c0577b74>] (of_irq_get+0x48/0x58)
[<c0577b74>] (of_irq_get) from [<c0540a14>] (i2c_device_probe+0x54/0x15c)
[<c0540a14>] (i2c_device_probe) from [<c04750dc>] (driver_probe_device+0x184/0x2c8)
[<c04750dc>] (driver_probe_device) from [<c0475310>] (__driver_attach+0x9c/0xa0)
[<c0475310>] (__driver_attach) from [<c0473238>] (bus_for_each_dev+0x7c/0xb0)
[<c0473238>] (bus_for_each_dev) from [<c0474af4>] (driver_attach+0x28/0x30)
[<c0474af4>] (driver_attach) from [<c0474760>] (bus_add_driver+0x154/0x200)
[<c0474760>] (bus_add_driver) from [<c0476348>] (driver_register+0x88/0x108)
[<c0476348>] (driver_register) from [<c0541600>] (i2c_register_driver+0x3c/0x90)
[<c0541600>] (i2c_register_driver) from [<bf003018>] (pcf857x_init+0x18/0x24 [gpio_pcf857x])
[<bf003018>] (pcf857x_init [gpio_pcf857x]) from [<c000998c>] (do_one_initcall+0x128/0x1e8)
[<c000998c>] (do_one_initcall) from [<c06a4220>] (do_init_module+0x6c/0x1bc)
[<c06a4220>] (do_init_module) from [<c00dd0c8>] (load_module+0x18e8/0x21c4)
[<c00dd0c8>] (load_module) from [<c00ddaa0>] (SyS_init_module+0xfc/0x158)
[<c00ddaa0>] (SyS_init_module) from [<c000ff40>] (ret_fast_syscall+0x0/0x54)
The IRQ chip interface defines only two callbacks which are executed in
non-atomic contex - irq_bus_lock/irq_bus_sync_unlock, so lets move
PM runtime calls there.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds support for the GPIOs found on the ITE super-I/O chips
IT87xx.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The parameter offset is an unsigned, so it makes no sense to compare
it for >= 0. Fix the compiler warning regarding this by removing this
comparison.
As the macro GPIO_OFFSET_VALID is only used at this single place, simplify
the code by dropping the macro completely and dropping the invert, too.
No functional change.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This fixes error checking in the function device_pca957x_init
to properly check and return error code values from the calls
to the function pca953x_write_regs if they fail as to properly
signal callers when a error occurs due a failure when writing
registers for this gpio based device.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Turn the ath79 driver into a true driver supporting multiple
instances. While at it also removed unneed includes and make use of
the BIT() macro.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove this driver now that Bjorn has introduced a pinctrl driver
for msm8660 and the dts files have been updated with the pinctrl
compatibles.
Cc: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The state container of the Zynq GPIO driver is sometimes
extracted from the gpio_chip exploiting the fact that offsetof()
the struct gpio_chip inside the struct zynq_gpio is 0, so
the container_of() is in practice a noop. However if a member
is added to struct zynq_gpio in front of struct gpio_chip,
things will break. Using proper container_of() avoids this
problem.
Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.
Also replace some explicit container_of() calls with the helper
function.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ezra Savard <ezra.savard@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The state container of the vf610 GPIO driver is sometimes
extracted from the gpio_chip exploiting the fact that offsetof()
the struct gpio_chip inside the struct vf610_gpio_port is 0, so
the container_of() is in practice a noop. However if a member
is added to struct vf610_gpio_port in front of struct gpio_chip,
things will break. Using proper container_of() avoids this
problem.
Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.
Also replace some explicit container_of() calls with the helper
function.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The state container of the sx150x GPIO driver is sometimes
extracted from the gpio_chip exploiting the fact that offsetof()
the struct gpio_chip inside the struct sx150x_chip is 0, so
the container_of() is in practice a noop. However if a member
is added to struct sx150_chip in front of struct gpio_chip, things
will break. Using proper container_of() avoids this problem.
Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The state container of the Altera GPIO driver is extracted from
the gpio_chip exploiting the fact that offsetof() the
struct gpio_chip inside the struct of_mm_gpio_chip are both 0, so
the container_of() is in practice a noop. However if a member
is added to struct altera_gpio_chip in front of
struct of_mm_gpio_chip, things will break. Using proper
container_of() avoids this problem.
Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.
Cc: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The state container of the etraxfs GPIO driver is extracted from
the gpio_chip exploiting the fact that offsetof() the
struct gpio_chip inside the struct bgpio_chip are both 0, so
the container_of() is in practice a noop. However if a member
is added to struct etraxfs_gpio_chip in front of
struct bgpio_chip, things will break. Using proper container_of()
avoids this problem.
Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.
Acked-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I couldn't follow this code flow. Make it dirt simple to figure
out what is going on and get proper debug prints. Warn if we
set up an IRQ without any trigger. Should make no semantic
difference.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This refactors the changes to the GPIO line naming mechanism to
not have so widespread effects, instead we conclude the patch series
by having created a name attribute in the GPIO descriptor, that need
not be globally unique, and it will be initialized from the old
.names array in struct gpio_chip if it exists, then used in the legacy
sysfs code like the array was used previously.
The associated changes to name lines from the device tree are
controversial and need to stand alone from this. Resulting changes:
1. Remove the export and the header for the gpio_name_to_desc() as so
far the only use is inside gpiolib.c. Staticize gpio_name_to_desc()
and move it above the only function using it.
2. Only print a warning if there are two GPIO lines with the same name.
The reason is to preserve current behaviour: before the previous
changes to the naming mechanism this would not reject probing the
driver, instead the error would occur when trying to export the line
in sysfs, so restore this behaviour, but print a friendly warning
if names collide.
Cc: Johan Hovold <johan@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add some information about gpio names to the debugfs gpio file. name and
label of a GPIO are then displayed next to each other. This way it is
easy to see what the real name of GPIO is and what the driver requested
it for.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[Dropped unsolicited sysfs ABI patch hunk]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The name is now stored in the gpio descriptor as well, for example to
allow to store names from DT. This patch changes the sysfs gpio files
to use the gpio descriptor name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds GPIO names to the GPIO descriptors when initializing the
gpiochip. It also introduces a check whether any of the new names will
conflict with an existing GPIO name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The latest gpio hogging mechanism assigns each gpio a 'line-name' in the
devicetree. The 'name' field is different from the 'label' field.
'label' is only used for requested GPIOs to describe its current use by
driver or userspace.
The 'name' field describes the GPIO itself, not the use. This is most
likely identical to the label in the schematic on the GPIO line and
should help to find this particular GPIO.
This is equivalent to the gpiochip->names array. However names should be
stored in the GPIO descriptor. We will use gpiochip->names in the future
only as initializer for the GPIO descriptors for drivers that assign
GPIO names hardcoded. All other GPIO names will be parsed from DT and
directly assigned to the GPIO descriptor.
This patch adds a helper function to find gpio descriptors by name
instead of gpio number.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio hogging functions are currently only used for gpio-hogging. But
these functions are widely generic ones which parse gpio device nodes in
the DT.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is a rather large update post rc1 due to the final steps of
cleanups and API changes which had to wait for the preparatory patches
to hit your tree.
- Regression fixes for ARM GIC irqchips
- Regression fixes and lockdep anotations for renesas irq chips
- The leftovers of the cleanup and preparatory patches which have
been ignored by maintainers
- Final conversions of the newly merged users of obsolete APIs
- Final removal of obsolete APIs
- Final removal of ARM artifacts which had been introduced during the
conversion of ARM to the generic interrupt code.
- Final split of the irq_data into chip specific and common data to
reflect the needs of hierarchical irq domains.
- Treewide removal of the first argument of interrupt flow handlers,
i.e. the irq number, which is not used by the majority of handlers
and simple to retrieve from the other argument the irq descriptor.
- A few comment updates and build warning fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
arm64: Remove ununsed set_irq_flags
ARM: Remove ununsed set_irq_flags
sh: Kill off set_irq_flags usage
irqchip: Kill off set_irq_flags usage
gpu/drm: Kill off set_irq_flags usage
genirq: Remove irq argument from irq flow handlers
genirq: Move field 'msi_desc' from irq_data into irq_common_data
genirq: Move field 'affinity' from irq_data into irq_common_data
genirq: Move field 'handler_data' from irq_data into irq_common_data
genirq: Move field 'node' from irq_data into irq_common_data
irqchip/gic-v3: Use IRQD_FORWARDED_TO_VCPU flag
irqchip/gic: Use IRQD_FORWARDED_TO_VCPU flag
genirq: Provide IRQD_FORWARDED_TO_VCPU status flag
genirq: Simplify irq_data_to_desc()
genirq: Remove __irq_set_handler_locked()
pinctrl/pistachio: Use irq_set_handler_locked
gpio: vf610: Use irq_set_handler_locked
powerpc/mpc8xx: Use irq_set_handler_locked()
powerpc/ipic: Use irq_set_handler_locked()
powerpc/cpm2: Use irq_set_handler_locked()
...
|
|
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
|
|
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor. Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
|
|
Make device_get_next_child_node() work with ACPI data-only subnodes
introduced previously.
Namely, replace acpi_get_next_child() with acpi_get_next_subnode()
that can handle (and return) child device objects as well as child
data-only subnodes of the given device and modify the ACPI part
of the GPIO subsystem to handle data-only subnodes returned by it.
To that end, introduce acpi_node_get_gpiod() taking a struct
fwnode_handle pointer as the first argument. That argument may
point to an ACPI device object as well as to a data-only subnode
and the function should do the right thing (ie. look for the matching
GPIO descriptor correctly) in either case.
Next, modify fwnode_get_named_gpiod() to use acpi_node_get_gpiod()
instead of acpi_get_gpiod_by_index() which automatically causes
devm_get_gpiod_from_child() to work with ACPI data-only subnodes
that may be returned by device_get_next_child_node() which in turn
is required by the users of that function (the gpio_keys_polled
and gpio-leds drivers).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Split acpi_get_gpiod_by_index() into three smaller routines to
allow the subsequent change of the generic firmware node properties
code to be more strarightforward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Modify is_acpi_node() to return "true" for ACPI data-only subnodes as
well as for ACPI device objects and change the name of to_acpi_node()
to to_acpi_device_node() so it is clear that it covers ACPI device
objects only. Accordingly, introduce to_acpi_data_node() to cover
data-only subnodes in an analogous way.
With that, make the fwnode_property_* family of functions work with
ACPI data-only subnodes introduced previously.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
If gpio-omap probe fails with -EPROBE_DEFER, the GPIO numbering
keeps increasing. Only increase the gpio count if gpiochip_add()
was successful as otherwise the numbers will increase for each
probe attempt.
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently we gpio-omap breaks if gpiochip_add() returns -EPROBE_DEFER:
[ 0.570000] gpiochip_add: GPIOs 0..31 (gpio) failed to register
[ 0.570000] omap_gpio 48310000.gpio: Could not register gpio chip -517
...
[ 3.670000] omap_gpio 48310000.gpio: Unbalanced pm_runtime_enable!
Let's fix the issue by adding the missing pm_runtime_put() on error.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The driver has a I2C device id table that is used to create the module
aliases and also "sx150x" isn't a supported I2C id, so it's never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It's possible to have gpio chips hanging off unreliable remote buses
where the get() operation will fail to acquire a readout of the current
gpio state. Propagate these errors to the consumer so that they can
act on, retry or ignore these failing reads, instead of treating them as
the line being held high.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
8cd1470("gpio: rcar: Add r8a7795 (R-Car H3) support") added
GPIO support for r8a7795. r8a7795 based on CONFIG_ARM64.
OTOH, GPIO_RCAR driver can be compiled fine on non-ARM.
This patch removed ARM dependency for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Need to check return value of irq_alloc_generic_chip, because
it may return NULL.
1. Change mxs_gpio_init_gc return type from void to int.
2. Add a new lable out_irqdomain_remove to remove the irq domain
when mxc_gpio_init_gc fail.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Need to check return value of irq_alloc_generic_chip, because
it may return NULL.
1. Change mxc_gpio_init_gc return type from void to int.
2. Add a new lable out_irqdomain_remove to remove the irq domain
when mxc_gpio_init_gc fail.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
[Manually rebased]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
|
|
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
GPIO drivers should be in drivers/gpio
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10597/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This reverts commit 5e22ec019823b0204720e1ad9a5866c638332b3a.
|
|
There is a helper function to do the container_of() magic for
the tc3589x GPIO, so use it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO IRQ controller is able to generate level triggered
interrupts, however, these were handled by handle_simple_irq so far
which did not take care of IRQ masking. This lead to "nobody cared
(try booting with the "irqpoll" option)" stack traces.
Use the generic interrupt handlers depending on the IRQ type.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This fixes error handling in the function max732x_probe by checking
if the calls to the function max732x_readb fail by returning a error
code.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As per CCF documentation (clk.txt) the clk_prepare/unprepare APIs
are not allowed in atomic context. But now OMAP GPIO driver
uses them while applying debounce settings and as part
of PM runtime irqsafe operations:
- omap_gpio_debounce() is holding the lock with IRQs off.
+ omap2_set_gpio_debounce()
+ clk_prepare_enable()
+ clk_prepare() this one might sleep.
- pm_runtime_get_sync() is holding the lock with IRQs off
+ omap_gpio_runtime_suspend()
+ raw_spin_lock_irqsave()
+ omap_gpio_dbck_disable()
+ clk_disable_unprepare()
Hence, fix it by moeving dbclk prepare/unprepare in OMAP GPIO
omap_gpio_probe/omap_gpio_remove. Also, while here, ensure that
debounce functionality is disabled if clk_get() failed,
because otherwise kernel will carsh in omap2_set_gpio_debounce().
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The access to HW registers has to be be protected in
omap_gpio_irq_handler(), as it may race with code executed on
another CPUs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
According to TRMs:
Required input line stable =
(the value of the GPIO_DEBOUNCINGTIME[7:0].DEBOUNCETIME + 1) × 31,
where the value of the GPIO_DEBOUNCINGTIME[7:0].DEBOUNCETIME bit field
is from 0 to 255.
But now omap2_set_gpio_debounce() will calculate debounce time and
behave incorrectly in the following cases:
1) requested debounce time is !0 and <32
calculated DEBOUNCETIME = 0x1 == 62 us;
expected value of DEBOUNCETIME = 0x0 == 31us
2) requested debounce time is 0
calculated DEBOUNCETIME = 0x1 == 62 us;
expected: disable debounce and DEBOUNCETIME = 0x0
3) requested debounce time is >32 and <63
calculated DEBOUNCETIME = 0x0 and debounce will be disabled;
expected: enable debounce and DEBOUNCETIME = 0x1 == 62 us
Hence, rework omap2_set_gpio_debounce() to fix above cases:
1) introduce local variable "enable" and use it to identify
when debounce need to be enabled or disabled. Disable debounce
if requested debounce time is 0.
2) use below formula for debounce time calculation:
debounce = (DIV_ROUND_UP(debounce, 31) - 1) & 0xFF;
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Switch OMAP GPIO driver to use platform_get_irq(), because
it is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ, ..)
for requesting IRQ resources any more, as they can be not ready yet
in case of DT-boot.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
