summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/i915/intel_sdvo.c
AgeCommit message (Collapse)Author
2015-10-08Revert "drm/i915: Call encoder hotplug for init and resume cases"Daniel Vetter
This reverts commit 5d250b05918c002b63632c7db91c3c5f924c6a3b. It results on a deadlock on platforms where we need to (at least partially) re-init hpd interrupts from power domain code, since ->hot_plug might again grab a power well reference (to do edid/dp_aux transactions. At least chv is affected. Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> References: http://mid.gmane.org/20151008133548.GX26517@intel.com Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2015-10-06drm/i915: Call encoder hotplug for init and resume casesSonika Jindal
For all the encoders, call the hot_plug if it is registered. This is required for connected boot and resume cases to generate fake hpd resulting in reading of edid. Removing the initial sdvo hot_plug call too so that it will be called just once from this loop. Signed-off-by: Sonika Jindal <sonika.jindal@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-09-30drm/i915: Add HDMI aspect ratio property for SDVOVille Syrjälä
Handle the HDMI aspect ratio property the same way in the SDVO code as we handle it in the HDMI code. v2: Remove stray whitespace change Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-09-30drm/i915: Constify adjusted_modeVille Syrjälä
Make adjusted_mode const whereever we don't have to modify it. This only covers cases when we have a local adjusted_mode variable, and doesn't make any difference for cases where we just dereference pipe_config->adjusted_mode. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-09-30drm/i915: Always use crtc_ timings when dealing with adjustead_modeVille Syrjälä
The adjustead_mode crtc_ timings are what we will program into the hardware, so it's those timings we should be looking practically everywhere. The normal and crtc_ timings should differ only when stere doubling is used. In that case the normal timings are the orignal non-doubled timigns, and crtc_ timings are the doubled timings used by the hardware. The only case where we continue to look at the normal timings is when we pass the adjusted_mode to drm_match_{cea,hdmi}_mode() to find the VIC. drm_edid keeps the modes aronund in the non-double form only, so it needs the non-double timings to match against. Done with sed 's/adjusted_mode->\([vhVH]\)/adjusted_mode->crtc_\1/g' 's/adjusted_mode->clock/adjusted_mode->crtc_clock/g' with a manual s/VDisplay/vdisplay/ within the comment in intel_dvo.c v2: Update due to intel_dsi.c changes Reviewed-by: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-09-30drm/i915: s/mode/adjusted_mode/ in functions that really get passed the ↵Ville Syrjälä
adjusted_mode Rename the function argument to 'adjusted_mode' whenever the function only ever gets passed the adjusted_mode. v2: Update due to intel_dsi.c changes Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-09-30drm/i915: Always call the adjusted mode 'adjusted_mode'Ville Syrjälä
Always name any variable pointing at the adjusted mode as 'adjustead_mode'. This will make it much easier to identify when we should use the crtc_ timings and when we shoudln't. Conversion was performed with coccinelle: @@ expression E; identifier I; @@ - struct drm_display_mode *I = &E.adjusted_mode; + struct drm_display_mode *adjusted_mode = &E.adjusted_mode; <... - I + adjusted_mode ...> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> [danvet: Fixup conflicts.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-09-23drm/i915: Don't pass sdvo_reg to intel_sdvo_select_{ddc, i2c}_bus()Ville Syrjälä
intel_sdvo_select_ddc_bus() and intel_sdvo_select_i2c_bus() have no used for the passed in 'reg', so just drop it. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26drm/i915: Make some string arrays constVille Syrjälä
Most of our char* arrays are markes as const already, but a few slipped through the cracks. Fix it. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26drm/i915: Use ARRAY_SIZE() instead of hand rolling itVille Syrjälä
A couple of hand rolled ARRAY_SIZE()s caught my eye. Get rid of them. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-14drm/i915: Get rid of dpms handling.Maarten Lankhorst
This is now done completely atomically. Keep connectors_active for now, but make it mirror crtc_state->active. Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-14drm/i915: Validate the state after an atomic modeset only, and pass the state.Maarten Lankhorst
First step in removing dpms and validating atomic state. There can still be a mismatch in the connector state because the dpms callbacks are still used, but this can not happen immediately after a modeset. Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-07-27drm: Make the connector dpms callback return a value, v2.Maarten Lankhorst
This is required to properly handle failing dpms calls. When making a wait in i915 interruptible, I've noticed that the dpms sequence could fail with -ERESTARTSYS because it was waiting interruptibly for flips. So from now on allow drivers to fail in their connector dpms callback. Encoder and crtc dpms callbacks are unaffected. Changes since v1: - Update kerneldoc for the drm helper functions. Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> [danvet: Resolve conflicts due to different merge order.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-06-26Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds
Pull drm updates from Dave Airlie: "This is the main drm pull request for v4.2. I've one other new driver from freescale on my radar, it's been posted and reviewed, I'd just like to get someone to give it a last look, so maybe I'll send it or maybe I'll leave it. There is no major nouveau changes in here, Ben was working on something big, and we agreed it was a bit late, there wasn't anything else he considered urgent to merge. There might be another msm pull for some bits that are waiting on arm-soc, I'll see how we time it. This touches some "of" stuff, acks are in place except for the fixes to the build in various configs,t hat I just applied. Summary: New drivers: - virtio-gpu: KMS only pieces of driver for virtio-gpu in qemu. This is just the first part of this driver, enough to run unaccelerated userspace on. As qemu merges more we'll start adding the 3D features for the virgl 3d work. - amdgpu: a new driver from AMD to driver their newer GPUs. (VI+) It contains a new cleaner userspace API, and is a clean break from radeon moving forward, that AMD are going to concentrate on. It also contains a set of register headers auto generated from AMD internal database. core: - atomic modesetting API completed, enabled by default now. - Add support for mode_id blob to atomic ioctl to complete interface. - bunch of Displayport MST fixes - lots of misc fixes. panel: - new simple panels - fix some long-standing build issues with bridge drivers radeon: - VCE1 support - add a GPU reset counter for userspace - lots of fixes. amdkfd: - H/W debugger support module - static user-mode queues - support killing all the waves when a process terminates - use standard DECLARE_BITMAP i915: - Add Broxton support - S3, rotation support for Skylake - RPS booting tuning - CPT modeset sequence fixes - ns2501 dither support - enable cmd parser on haswell - cdclk handling fixes - gen8 dynamic pte allocation - lots of atomic conversion work exynos: - Add atomic modesetting support - Add iommu support - Consolidate drm driver initialization - and MIC, DECON and MIPI-DSI support for exynos5433 omapdrm: - atomic modesetting support (fixes lots of things in rewrite) tegra: - DP aux transaction fixes - iommu support fix msm: - adreno a306 support - various dsi bits - various 64-bit fixes - NV12MT support rcar-du: - atomic and misc fixes sti: - fix HDMI timing complaince tilcdc: - use drm component API to access tda998x driver - fix module unloading qxl: - stability fixes" * 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits) drm/nouveau: Pause between setting gpu to D3hot and cutting the power drm/dp/mst: close deadlock in connector destruction. drm: Always enable atomic API drm/vgem: Set unique to "vgem" of: fix a build error to of_graph_get_endpoint_by_regs function drm/dp/mst: take lock around looking up the branch device on hpd irq drm/dp/mst: make sure mst_primary mstb is valid in work function of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi' drm/atomic: Don't set crtc_state->enable manually drm/exynos: dsi: do not set TE GPIO direction by input drm/exynos: dsi: add support for MIC driver as a bridge drm/exynos: dsi: add support for Exynos5433 drm/exynos: dsi: make use of array for clock access drm/exynos: dsi: make use of driver data for static values drm/exynos: dsi: add macros for register access drm/exynos: dsi: rename pll_clk to sclk_clk drm/exynos: mic: add MIC driver of: add helper for getting endpoint node of specific identifiers drm/exynos: add Exynos5433 decon driver ...
2015-06-08drm/i915: Properly initialize SDVO analog connectorsAnder Conselvan de Oliveira
In the commit below, I missed the connector allocation in the function intel_sdvo_analog_init(), leading to those connectors to have a NULL state pointer. commit 08d9bc920d465bbbbd762cac9383249c19bf69a2 Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Date: Fri Apr 10 10:59:10 2015 +0300 drm/i915: Allocate connector state together with the connectors Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2015-05-21drm/i915: Disable SDVO port after the pipe on PCH platformsVille Syrjälä
While at it also remove the redundant/unneeded w/a like done for hdmi already. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> [danvet: Mention that this also removes the unneeded w/a, as suggested by Jesse.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-05-21drm/i915: Fix the IBX transcoder B workaroundsVille Syrjälä
Currently the IBX transcoder B workarounds are not working correctly. Well, the HDMI one seems to be working somewhat, but the DP one is definitely busted. After a bit of experimentation it looks like the best way to make this work is first disable the port on transcoder B, and then re-enable it transcoder A, and immediately disable it again. We can also clean up the code by noting that we can't be called without a valid crtc. And also note that port A on ILK does not need the workaround, so let's check for that one too. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-05-21drm/i915: Write the SDVO reg twice on IBXVille Syrjälä
On IBX the SDVO/HDMI register write may be masked when enabling the port, so it may need to written twice. The HDMI code does this, but the SDVO code does not. Add the workaround to the SDVO code as well. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-05-08drm/i915: Use POSTING_READ() in intel_sdvo_write_sdvox()Ville Syrjälä
Use POSTING_READ() in intel_sdvo_write_sdvox() as appropriate. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-13drm/i915: Allocate connector state together with the connectorsAnder Conselvan de Oliveira
Connector states were being allocated in intel_setup_outputs() in loop over all connectors. That meant hot-added connectors would have a NULL state. Since the change to use a struct drm_atomic_state for the legacy modeset, connector states are necessary for the i915 driver to function properly, so that would lead to oopses. Broken by commit 944b0c76575753da5a332aab0a1d8c6df65a076b Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Date: Fri Mar 20 16:18:07 2015 +0200 drm/i915: Copy the staged connector config to the legacy atomic state v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS) Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reported-and-tested-by: Nicolas Kalkhof <nkalkhof@web.de> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2015-04-13drm/i915: Allocate connector state together with the connectorsAnder Conselvan de Oliveira
Connector states were being allocated in intel_setup_outputs() in loop over all connectors. That meant hot-added connectors would have a NULL state. Since the change to use a struct drm_atomic_state for the legacy modeset, connector states are necessary for the i915 driver to function properly, so that would lead to oopses. v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS) Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reported-and-tested-by: Nicolas Kalkhof <nkalkhof@web.de> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-01drm/i915: base gmbus pin validity check on the gmbus pin map arrayJani Nikula
This will be helpful for adding future platforms. It is better to keep the information in the single point of truth (the table) instead of duplicating it into the validity function. While at it, add dev_priv parameter to the function, also to prepare for adding future platform support. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-01drm/i915: refer to pin instead of port in the intel_i2c.c interfacesJani Nikula
Rename intel_gmbus_is_port_valid to intel_gmbus_is_valid_pin, and rename port parameters to pin as well. This matches usage all around, as usually a pin is passed to the validity check function. No functional changes. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-01drm/i915: rename GMBUS_PORT_* macros as GMBUS_PIN_*Jani Nikula
The specs refer to pin pairs. Start moving towards using pin rather than port all around to avoid confusion. No functional changes. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26drm/i915: Implement connector state duplicationAnder Conselvan de Oliveira
So that we can add connector states to the drm_atomic_state used in the legacy modeset. Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-17drm/i915: Fix trivial typos in comments and warning messageYannick Guerrini
Change 'mutliple' to 'multiple' Change 'mutlipler' to 'multiplier' Change 'Haswel' to 'Haswell' Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-01-27drm/i915: Add atomic_get_property entrypoint for connectors (v2)Matt Roper
Even though we only support atomic plane updates at the moment, we still need to add an .atomic_get_property() entrypoint for connectors before we allow the driver to flip on the DRIVER_ATOMIC bit. As soon as that bit gets set, the DRM core will start adding atomic connector properties (in addition to the plane properties we care about at the moment), so we need to be able to handle the new way the DRM core will interact with us. For simplicity, we just lookup driver-specific connector properties in the usual shadow array maintained by the core. Once we get real atomic modeset support for crtc's and planes, this code should be re-written to pull the data out of crtc/connector state structures. v2: Fix intel_dvo and intel_dsi that I missed on the first pass (Ander) Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-01-27drm/i915: Setup dummy atomic state for connectors (v3)Matt Roper
We want to enable/test plane updates via the atomic interface, but as soon as we flip DRIVER_ATOMIC on, the DRM core will take some atomic codepaths to lookup properties during drmModeGetConnector() and some of those codepaths unconditionally dereference connector->state (specifically when looking up the CRTC ID property in drm_atomic_connector_get_property()). Create a dummy connector state for each connector at init time to ensure the DRM core doesn't try to dereference a NULL connector->state. The actual connector properties will never be updated or contain useful information, but since we're doing this specifically for testing/debug of the plane operations (and only when a specific kernel module option is given), that shouldn't really matter. Once we start creating connector states, the DRM core will want to be able to clean them up for us. We also need to hook up the destruction entrypoint to the core's helper. v2: Squash in the patch to set the state destruction hook (Ander & Bob) v3: Only create dummy connector states when we're actually faking atomic support. (Ander) Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-01-27drm/i915: Make intel_crtc->config a pointerAnder Conselvan de Oliveira
To match the semantics of drm_crtc->state, which this will eventually become. The allocation of the memory for config will be fixed in a followup patch. By adding the extra _config field to intel_crtc it was possible to generate this entire patch with the cocci script below. @@ @@ struct intel_crtc { ... -struct intel_crtc_state config; +struct intel_crtc_state _config; +struct intel_crtc_state *config; ... } @@ struct intel_crtc *crtc; @@ -memset(&crtc->config, 0, sizeof(crtc->config)); +memset(crtc->config, 0, sizeof(*crtc->config)); @@ @@ __intel_set_mode(...) { <... -to_intel_crtc(crtc)->config = *pipe_config; +(*(to_intel_crtc(crtc)->config)) = *pipe_config; ...> } @@ @@ intel_crtc_init(...) { ... WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe); +intel_crtc->config = &intel_crtc->_config; return; ... } @@ struct intel_crtc *crtc; @@ -&crtc->config +crtc->config @@ struct intel_crtc *crtc; identifier member; @@ -crtc->config.member +crtc->config->member @@ expression E; @@ -&(to_intel_crtc(E)->config) +to_intel_crtc(E)->config @@ expression E; identifier member; @@ -to_intel_crtc(E)->config.member +to_intel_crtc(E)->config->member v2: Clarify manual changes by splitting them into another patch. (Matt) Improve cocci script to generate even more of the changes. (Ander) Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-01-27drm/i915: Embedded struct drm_crtc_state in intel_crtc_stateAnder Conselvan de Oliveira
And get rid of the duplicate mode structures. This patch was generated with the following semantic patch: @@ @@ struct intel_crtc_state { +struct drm_crtc_state base; + ... -struct drm_display_mode requested_mode; -struct drm_display_mode adjusted_mode; ... } @@ struct intel_crtc_state *state; @@ -state->adjusted_mode +state->base.adjusted_mode @@ struct intel_crtc_state *state; @@ -state->requested_mode +state->base.mode @@ struct intel_crtc_state state; @@ -state.adjusted_mode +state.base.adjusted_mode @@ struct intel_crtc_state state; @@ -state.requested_mode +state.base.mode @@ struct drm_crtc *crtc; @@ -to_intel_crtc(crtc)->config.adjusted_mode +to_intel_crtc(crtc)->config.base.adjusted_mode @@ identifier member; expression E; @@ -PIPE_CONF_CHECK_FLAGS(adjusted_mode.member, E); +PIPE_CONF_CHECK_FLAGS(base.adjusted_mode.member, E); @@ identifier member; @@ -PIPE_CONF_CHECK_I(adjusted_mode.member); +PIPE_CONF_CHECK_I(base.adjusted_mode.member); @@ identifier member; @@ -PIPE_CONF_CHECK_CLOCK_FUZZY(adjusted_mode.member); +PIPE_CONF_CHECK_CLOCK_FUZZY(base.adjusted_mode.member); v2: Completely generate the patch with cocci. (Ander) Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-01-27drm/i915: Rename struct intel_crtc_config to intel_crtc_stateAnder Conselvan de Oliveira
The objective is to make this structure usable with the atomic helpers, so let's start with the rename. Patch generated with coccinelle: @@ @@ -struct intel_crtc_config { +struct intel_crtc_state { ... } @@ @@ -struct intel_crtc_config +struct intel_crtc_state v2: Completely generate the patch with cocci. (Ander) Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-01-13drm/i915: Don't pretend SDVO hotplug works on 915Ville Syrjälä
915 doens't support hotplug at all, so we shouldn't try to pretend otherwise in the SDVO code. Note: i915 does have hotplug support in hw, we simply never enabled it in i915.ko: There's only one hpd bit for all outputs, so not worth the bother to add this special case for this rather old platform. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> [danvet: Clarify that only i915.ko doesn't support hpd on i915g.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-10-31drm/i915: Don't destroy DRM properties in the driverDamien Lespiau
When drm properties are created, they are added to mode_config.property_list, which is then used in drm_mode_config_cleanup() to destroy every single property created by the driver. Cc: Chandra Konduru <chandra.konduru@intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-07-08Merge tag 'topic/core-stuff-2014-06-30' of ↵Dave Airlie
git://anongit.freedesktop.org/drm-intel into drm-next misc core patches picked up by Daniel and Jani. * tag 'topic/core-stuff-2014-06-30' of git://anongit.freedesktop.org/drm-intel: drm/fb-helper: Remove unnecessary list empty check in drm_fb_helper_debug_enter() drm/fb-helper: Redundant info->fix.type_aux setting in drm_fb_helper_fill_fix() drm/debugfs: add an "edid_override" file per connector drm/debugfs: add a "force" file per connector drm: add register and unregister functions for connectors drm: fix uninitialized acquire_ctx fields (v2) drm: Driver-specific ioctls range from 0x40 to 0x9f drm: Don't export internal module variables
2014-06-19drm: add register and unregister functions for connectorsThomas Wood
Introduce generic functions to register and unregister connectors. This provides a common place to add and remove associated user space interfaces. Signed-off-by: Thomas Wood <thomas.wood@intel.com> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-06-11drm/i915: Avoid div-by-zero when pixel_multiplier is zeroVille Syrjälä
On certain platforms pixel_multiplier is read out in .get_pipe_config(), but it also gets used to calculate the pixel clock in intel_sdvo_get_config(). If the pipe is disable but some SDVO outputs are active, we may end up dividing by zero in intel_sdvo_get_config(). To avoid the problem simply check for zero pixel_multiplier and skip the division. Another attempt at fixing this involved populating pixel_multiplier to 1 even for disabled pipes, but that triggered a WARN because SDVO_CMD_GET_CLOCK_RATE_MULT command failed and thus encoder_pixel_multiplier was left at zero and didn't match pipe_config->pixel_multiplier. The "divide by pixel_multiplier" operation got introduced here: commit 18442d08786472c63a0a80c27f92b033dffc26de Author: Ville Syrjälä <ville.syrjala@linux.intel.com> Date: Fri Sep 13 16:00:08 2013 +0300 drm/i915: Fix port_clock and adjusted_mode.clock readout all over and it has caused a regression on certain machines since they would hit the div-by-zero during resume. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76520 Cc: <stable@vger.kernel.org> # 3.13+ Tested-by: Tim Richardson <tim@tim-richardson.net> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2014-06-04drm/i915: replace drm_get_connector_name() with direct name field useJani Nikula
Generated using semantic patches: @@ expression E; @@ - drm_get_connector_name(&E) + E.name @@ expression E; @@ - drm_get_connector_name(E) + E->name v2: Turn drm_get_connector_name(&E) into E.name instead of &(E)->name. Acked-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2014-05-16drm/i915/sdvo: use config->has_hdmi_sinkDaniel Vetter
This way we can rely on the state cross-checker to have a bit assurance that we'll get it right. Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-05-16drm/i915: state readout and cross checking for limited_color_rangeDaniel Vetter
At least on those platforms which have a simple bit and don't rely on the fully programmable CSC unit to do this. Note that with the current code this includes CHV, but I guess that platform will match BYT. Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-05-16drm/i915/sdvo: Use pipe_config->limited_color_range consistentlyDaniel Vetter
We in the pre_enable hook we should only rely on the pipe config and not on some other state set through properties or detect functions. Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-05-05drm/i915/sdvo: Remove ->mode_set callbackDaniel Vetter
SDVO is used by both crtcs using the i9xx_ and the ironlake_ functions. For both cases there is nothing between the encoder->mode_set and the encoder->pre_enable calls that touches the hardware. The vlv_ functions are different since they enable the pll before the ->pre_enable hook. But SDVO isn't supported on vlv platforms, so this doesn't matter. We've also already clean up all the sdvo state computation logic, all relevant parts are already in the ->compute_config hook. So we can just get rid of the ->mode_set hook by converting it to a ->pre_enable hook. Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-04-15drm/i915/SDVO: For sysfs link put directory and target in correct orderEgbert Eich
When linking the i2c sysfs file into the connector's directory pass directory and link target in the right order. This code was introduced with: commit 931c1c26983b4f84e33b78579fc8d57e4a14c6b4 Author: Imre Deak <imre.deak@intel.com> Date: Tue Feb 11 17:12:51 2014 +0200 drm/i915: sdvo: add i2c sysfs symlink to the connector's directory This is the same what we do for DP connectors, so make things more consistent. Signed-off-by: Egbert Eich <eich@suse.de> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-03-21drm/i915/sdvo: fix questionable return value checkJani Nikula
intel_sdvo_get_trained_inputs() returns a bool, check the status accordingly. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-03-10drm/i915: Make encoder cloning more flexibleVille Syrjälä
Currently we allow encoders to indicate whether they can be part of a cloned set with just one flag. That's not flexible enough to describe the actual hardware capabilities. Instead make it a bitmask of encoder types with which the current encoder can be cloned. For now we set the bitmask to allow DVO+DVO and DVO+VGA, which should match what the old boolean flag allowed. We will add some more cloning options in the future. Note that this patch also removes the encoder.possible_clones setting from encoder setup code - we compute this dynamically. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> [danvet: Add Ville's explanation why removing the encoder possible_clones is save.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-02-14drm/i915: sdvo: add i2c sysfs symlink to the connector's directoryImre Deak
This is the same what we do for DP connectors, so make things more consistent. Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-02-14drm/i915: sdvo: fix error path in sdvo_connector_initImre Deak
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-02-14drm/i915: add unregister callback to connectorImre Deak
Since commit d9255d57147e1dbcebdf6670409c2fa0ac3609e6 Author: Paulo Zanoni <paulo.r.zanoni@intel.com> Date:   Thu Sep 26 20:05:59 2013 -0300 it became clear that we need to separate the unload sequence into two parts: 1. remove all interfaces through which new operations on some object (crtc, encoder, connector) can be started and make sure all pending operations are completed 2. do the actual tear down of the internal representation of the above objects The above commit achieved this separation for connectors by splitting out the sysfs removal part from the connector's destroy callback and doing this removal before calling drm_mode_config_cleanup() which does the actual tear-down of all the drm objects. Since we'll have to customize the interface removal part for different types of connectors in the upcoming patches, add a new unregister callback and move the interface removal part to it. No functional change. Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2013-12-10drm/i915: Don't cast away const from infoframe bufferVille Syrjälä
We don't modify the packed infoframe data, so we should keep the const qualifier in place. Just pass the buffer as 'const void *' instead of 'const uint8_t *' and we can drop the cast entirely. v2: Do intel_sdvo_write_infoframe() as well Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2013-11-28drm/i915: Return a drm_mode_status enum in the mode_valid vfuncsDamien Lespiau
We had some mode_valid() vfuncs returning an int, others the enum. Let's use the latter everywhere. Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2013-11-28drm/i915/sdvo: Fix up debug output to not split linesDaniel Vetter
It leads to a big mess when stuff interleaves. Especially with the new patch I've submitted for the drm core to no longer artificially split up debug messages. v2: The size parameter to snprintf includes the terminating 0, but the return value does not. Adjust the logic accordingly. Spotted by Mika. Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-09 10:38:58 +0000