| Age | Commit message (Collapse) | Author |
|---|
|
commit 2a2d95e9d6d29e726cc294b65391917ed2e32bf4 upstream.
If the I2C bus is put to a low power state by an ACPI method it might pull
the SDA line low (as its power is removed). Once the bus is put to full
power state again, the SDA line is pulled back to high. This transition
looks like a STOP condition from the controller point-of-view which sets
STOP detected bit in its status register causing the driver to fail
subsequent transfers.
Fix this by always clearing all interrupts before we start a transfer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6f34cea56f5b95498070eaa9f4aa3ba4a9e4f62 upstream.
i2c_dw_xfer_msg() pushes a number of bytes to transmit/receive
to/from the bus into the TX FIFO.
For master-rx transactions, the maximum amount of data that can be
received is calculated depending solely on TX and RX FIFO load.
This is racy - TX FIFO may contain master-rx data yet to be
processed, which will eventually land into the RX FIFO. This
data is not taken into account and the function may request more
data than the controller is actually capable of storing.
This patch ensures the driver takes into account the outstanding
master-rx data in TX FIFO to prevent RX FIFO overrun.
Signed-off-by: Josef Ahmad <josef.ahmad@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c39e8e4354ce4daf23336de5daa28a3b01f00aa6 upstream.
The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be
written, while the upper two bits are flags to indicate stop/start.
The driver apparently attempted to optimize write access, by only writing a
byte in those cases where the stop/start bits are zero. However, we have
seen cases where the lower byte is duplicated onto the upper byte by the
hardware, which causes inadvertent stop/starts.
This patch changes the write access to the transmit FIFO to always be 16 bits
wide.
Signed off by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ACPI handle of struct i2c_adapter's dev member should not be
set, because this causes that struct i2c_adapter to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct i2c_adapter). Consequently,
acpi_i2c_register_devices() should use the ACPI handle of the
parent of the struct i2c_adapter it is called for rather than the
struct i2c_adapter's ACPI handle (which should be NULL).
Make that happen and modify the i2c-designware-platdrv driver,
which currently is the only driver for ACPI-enumerated I2C
controller chips, not to set the ACPI handle for the
struct i2c_adapter it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
|
|
My old e-mail address is no longer working.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adds the iSMT SMBus Controller DeviceIDs for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.
clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Remove !S390 dependency from i2c Kconfig, since s390 now supports PCI, HAS_IOMEM
and HAS_DMA, however we need to add a couple of GENERIC_HARDIRQS dependecies to
fix compile and link errors like these:
ERROR: "devm_request_threaded_irq" [drivers/i2c/i2c-smbus.ko] undefined!
ERROR: "devm_request_threaded_irq" [drivers/i2c/busses/i2c-ocores.ko] undefined!
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
MAX_IDR_MASK is another weirdness in the idr interface. As idr covers
whole positive integer range, it's defined as 0x7fffffff or INT_MAX.
Its usage in idr_find(), idr_replace() and idr_remove() is bizarre.
They basically mask off the sign bit and operate on the rest, so if
the caller, by accident, passes in a negative number, the sign bit
will be masked off and the remaining part will be used as if that was
the input, which is worse than crashing.
The constant is visible in idr.h and there are several users in the
kernel.
* drivers/i2c/i2c-core.c:i2c_add_numbered_adapter()
Basically used to test if adap->nr is a negative number which isn't
-1 and returns -EINVAL if so. idr_alloc() already has negative
@start checking (w/ WARN_ON_ONCE), so this can go away.
* drivers/infiniband/core/cm.c:cm_alloc_id()
drivers/infiniband/hw/mlx4/cm.c:id_map_alloc()
Used to wrap cyclic @start. Can be replaced with max(next, 0).
Note that this type of cyclic allocation using idr is buggy. These
are prone to spurious -ENOSPC failure after the first wraparound.
* fs/super.c:get_anon_bdev()
The ID allocated from ida is masked off before being tested whether
it's inside valid range. ida allocated ID can never be a negative
number and the masking is unnecessary.
Update idr_*() functions to fail with -EINVAL when negative @id is
specified and update other MAX_IDR_MASK users as described above.
This leaves MAX_IDR_MASK without any user, remove it and relocate
other MAX_IDR_* constants to lib/idr.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: "Marciniszyn, Mike" <mike.marciniszyn@intel.com>
Cc: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Wolfram Sang <wolfram@the-dreams.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Wolfram Sang <wolfram@the-dreams.de>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Intel ismt & Broadcom bcm2835
- a number of drivers got support for more variants and mostly got
cleaned up on the way (sis630, i801, at91, tegra, designware)
- i2c got rid of all *_set_drvdata(..., NULL) on remove/probe failure
- removed the i2c_smbus_process_call from the core since there are no
users
- mxs can now switch between PIO and DMA depending on the message
size and the bus speed can now be arbitrary
In addition, there is the usual bunch of fixes, cleanups, devm_*
conversions, etc"
Fixed conflict (and buggy devm_* conversion) in i2c-s3c2410.c
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: Remove unneeded xxx_set_drvdata(..., NULL) calls
i2c: pxa: remove incorrect __exit annotations
i2c: ocores: Fix pointer to integer cast warning
i2c: tegra: remove warning dump if timeout happen in transfer
i2c: fix i2c-ismt.c printk format warning
i2c: i801: Add Device IDs for Intel Wellsburg PCH
i2c: add bcm2835 driver
i2c: ismt: Add Seth and Myself as maintainers
i2c: sis630: checkpatch cleanup
i2c: sis630: display unsigned hex
i2c: sis630: use hex to constants for SMBus commands
i2c: sis630: fix behavior after collision
i2c: sis630: clear sticky bits
i2c: sis630: Add SIS964 support
i2c: isch: Add module parameter for backbone clock rate if divider is unset
i2c: at91: fix unsed variable warning when building with !CONFIG_OF
i2c: Adding support for Intel iSMT SMBus 2.0 host controller
i2c: sh_mobile: don't send a stop condition by default inside transfers
i2c: sh_mobile: eliminate an open-coded "goto" loop
i2c: sh_mobile: fix timeout error handling
...
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
|
|
There is simply no reason to be manually setting the private driver
data to NULL in the remove/fail to probe cases. This is just extra
cruft code that can be removed.
A few notes:
* Nothing relies on drvdata being set to NULL.
* The __device_release_driver() function eventually calls
dev_set_drvdata(dev, NULL) anyway, so there's no need to do it
twice.
* I verified that there were no cases where xxx_get_drvdata() was
being called in these drivers and checking for / relying on the NULL
return value.
This could be cleaned up kernel-wide but for now just take the baby
step and remove from the i2c subsystem.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
The remove() methods should not be marked __exit unless we are using
platform_driver_probe() which disables unbinding device from driver
via sysfs.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
|
|
After commit a000b8c1 [i2c: ocores: Add support for the GRLIB port of the
controller and use function pointers for getreg and setreg function],
compiling i2c-ocores.c for 64-bit gives the following warning:
drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
drivers/i2c/busses/i2c-ocores.c:334:15: warning: cast from pointer to integer of different size
Fix it by casting the pointer to long.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If timeout error occurs in the i2c transfer then it was dumping warning
of call stack.
Remove the warning dump as there is may be possibility that some slave
devices are busy and not responding the i2c communication.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
Fix printk format warning. dma_addr_t can be 32-bit or 64-bit,
so cast it to long long for printing. This also matches the
printk format specifier that is already used.
drivers/i2c/busses/i2c-ismt.c:532:3: warning: format '%llX' expects argument of type 'long long unsigned int', but argument 4 has type 'dma_addr_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
This patch adds the SMBus Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
This implements a very basic I2C host driver for the BCM2835 SoC. Missing
features so far are:
* 10-bit addressing.
* DMA.
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
This patch corrects checkpatch errors.
The changes has also been removed as it has less meaning with version
control tools.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
This patch corrects the display of the acpi_base unsigned hex value.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
This patch replaces hexadecimal values by constants for SMBus commands.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
Datasheet on collision:
SMBus Collision (SMBCOL_STS)
This bit is set when a SMBus Collision condition occurs and
SMBus Host loses in the bus arbitration. The software should
clear this bit and re-start SMBus operation.
As the status will be cleared in transaction_end, we can remove the
sis630_write and prepare to return -EAGAIN to retry.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
The sticky bits must be cleared at the end of the transaction by writing
a 1 to all fields.
Datasheet:
SMBus Status (SMB_STS)
The following registers are all sticky bits and only can be
cleared by writing a one to their corresponding fields.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
It was observed the Host Clock Divider was not written by the driver. It
was still set to (default) 0, if not already set by BIOS, which caused
garbage on SMBus.
This driver adds a parameters which is used to calculate the divider
appropriately for a default bitrate of 100 KHz. This new divider is only
applied if the clock divider is still default 0.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
Commit 70d46a2 "i2c: at91: add dt support to i2c-at91"
added DT only support for at91sam9x5. Building i2c-at91
without CONFIG_OF now warns about at91sam9x5_config as
being unused.
drivers/i2c/busses/i2c-at91.c:556:30: warning: 'at91sam9x5_config' defined but not used [-Wunused-variable]
Move at91sam9x5_config under the defined(CONFIG_OF)
guard as new AT91 SoCs will be DT only.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
The iSMT (Intel SMBus Message Transport) supports multi-master I2C/SMBus,
as well as IPMI. It's operation is DMA-based and utilizes descriptors to
initiate transactions on the bus.
The iSMT hardware can act as both a master and a target, although this
driver only supports being a master.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Bill Brown <bill.e.brown@intel.com>
Tested-by: Seth Heasley <seth.heasley@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
By default there should be no stop bit on I2C between single messages
within transfers. Fix the driver to comply and only send a stop bit at
the end of transfers or if I2C_M_STOP is set.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
Eliminate an open-coded "goto" loop by introducing a function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
In a timeout case return an error immediately from the driver's
.master_xfer() method, instead of continuing and letting higher layers
fail.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
Reduce 2 boolean functions from "if (condition) return 1; return 0;" to
"return condition;"
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
This patch drops the i2c timing tables from this driver and instead
derives the timing based from the requested clock sleep. The timing
tables were completely wrong anyway when observed on a scope.
This new algorithm is also only derived by using a scope, but it seems
to produce much more accurate result.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
[wsa: changed messages from dev_err to dev_warn]
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
|
This patch adds the PCU SMBus DeviceID for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
|
|
Migrate Tegra clock support to drivers/clk/tegra, this involves
moving:
1. definition of tegra_cpu_car_ops to clk.c
2. definition of reset functions to clk-peripheral.c
3. change parent of cpu clock.
4. Remove legacy clock initialization.
5. Initialize clocks using DT.
6. Remove all instance of mach/clk.h
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: use to_clk_periph_gate().]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Signed-off-by: Giridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Add support for the PIO mode and mixed PIO/DMA mode support. The mixed
PIO/DMA is the default mode of operation. This shall leverage overhead
that the driver creates due to setting up DMA descriptors even for very
short transfers.
The current boundary between PIO/DMA 8 bytes, transfers shorter than 8
bytes are transfered by PIO, longer transfers use DMA. The performance
of write transfers remains unchanged, while there is a minor improvement
of read performance. Reading 16KB EEPROM with DMA-only operations gives
a read speed of 39.5KB/s, while with then new mixed-mode the speed is
blazing 40.6KB/s.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
err_cpufreq label is now used only once. It can be removed and related
code can be moved to the caller location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
In i2c-s3c2410 driver probe, only s3c24xx_i2c_init() needs the I2C clock
to be enabled. Moving clk_prepare_enable() and clk_disable_unprepare()
calls to around this function simplifies the return path of probe call.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
i2c-s3c2410 driver is modified to use devm_clk_get()
and devm_request_irq(). This also simplifies the
return path in driver's probe.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
err_noclk label redirects to a simple return statement. Move the
return statement to the caller location and remove the label.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
cppcheck rightfully reports those as "reassigned a value before the old
one has been used."
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
|
|
Amend the I2C nomadik pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an i2c transfer
- "idle" after initial default, after resume default, and after each
i2c xfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle, and for runtime cases inbetween
I2C transfers.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[wsa: fixed braces on one else-branch]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Ludovic Ddesroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
