| Age | Commit message (Collapse) | Author |
|---|
|
This patch split up struct ib_send_wr so that all non-trivial verbs
use their own structure which embedds struct ib_send_wr. This dramaticly
shrinks the size of a WR for most common operations:
sizeof(struct ib_send_wr) (old): 96
sizeof(struct ib_send_wr): 48
sizeof(struct ib_rdma_wr): 64
sizeof(struct ib_atomic_wr): 96
sizeof(struct ib_ud_wr): 88
sizeof(struct ib_fast_reg_wr): 88
sizeof(struct ib_bind_mw_wr): 96
sizeof(struct ib_sig_handover_wr): 80
And with Sagi's pending MR rework the fast registration WR will also be
down to a reasonable size:
sizeof(struct ib_fastreg_wr): 64
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> [srp, srpt]
Reviewed-by: Chuck Lever <chuck.lever@oracle.com> [sunrpc]
Tested-by: Haggai Eran <haggaie@mellanox.com>
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
|
|
The majority of callers never check the return value, and even if they
did, they can't do anything about a failure.
All possible failure cases represent a bug in the caller, so just
WARN_ON inside the function instead.
This fixes a few random errors:
net/rd/iw.c infinite loops while it fails. (racing with EBUSY?)
This also lays the ground work to get rid of error return from the
drivers. Most drivers do not error, the few that do are broken since
it cannot be handled.
Since uverbs can legitimately make use of EBUSY, open code the
check.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The pd now has a local_dma_lkey member which completely replaces
ib_get_dma_mr, use it instead.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If the above is turned off then ipoib_cm_dev_init unconditionally
returns ENOSYS, and the newly added error handling in
0b3957 prevents ipoib from coming up at all:
kernel: mlx4_0: ipoib_transport_dev_init failed
kernel: mlx4_0: failed to initialize port 1 (ret = -12)
Fixes: 0b39578bcde4 (IB/ipoib: Use dedicated workqueues per interface)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Currently, ib_create_cq uses cqe and comp_vecotr instead
of the extendible ib_cq_init_attr struct.
Earlier patches already changed the vendors to work with
ib_cq_init_attr. This patch changes the consumers too.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The current code in the RX flow uses two sg entries for each incoming
packet, the first one was for the IB headers and the second for the rest
of the data, that causes two dma map/unmap and two allocations, and few
more actions that were done at the data path.
Use only one linear skb on each incoming packet, for the data (IB
headers and payload), that reduces the packet processing in the
data-path (only one skb, no frags, the first frag was not used anyway,
less memory allocations) and the dma handling (only one dma map/unmap
over each incoming packet instead of two map/unmap per each incoming packet).
After commit 73d3fe6d1c6d ("gro: fix aggregation for skb using frag_list") from
Eric Dumazet, we will get full aggregation for large packets.
When running bandwidth tests before and after the (over the card's numa node),
using "netperf -H 1.1.1.3 -T -t TCP_STREAM", the results before are ~12Gbs before
and after ~16Gbs on my setup (Mellanox's ConnectX3).
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
During my recent work on the rtnl lock deadlock in the IPoIB driver, I
saw that even once I fixed the apparent races for a single device, as
soon as that device had any children, new races popped up. It turns
out that this is because no matter how well we protect against races
on a single device, the fact that all devices use the same workqueue,
and flush_workqueue() flushes *everything* from that workqueue means
that we would also have to prevent all races between different devices
(for instance, ipoib_mcast_restart_task on interface ib0 can race with
ipoib_mcast_flush_dev on interface ib0.8002, resulting in a deadlock on
the rtnl_lock).
There are several possible solutions to this problem:
Make carrier_on_task and mcast_restart_task try to take the rtnl for
some set period of time and if they fail, then bail. This runs the
real risk of dropping work on the floor, which can end up being its
own separate kind of deadlock.
Set some global flag in the driver that says some device is in the
middle of going down, letting all tasks know to bail. Again, this can
drop work on the floor.
Or the method this patch attempts to use, which is when we bring an
interface up, create a workqueue specifically for that interface, so
that when we take it back down, we are flushing only those tasks
associated with our interface. In addition, keep the global
workqueue, but now limit it to only flush tasks. In this way, the
flush tasks can always flush the device specific work queues without
having deadlock issues.
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This reverts commit 5141861cd5e17eac9676ff49c5abfafbea2b0e98.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
During my recent work on the rtnl lock deadlock in the IPoIB driver, I
saw that even once I fixed the apparent races for a single device, as
soon as that device had any children, new races popped up. It turns
out that this is because no matter how well we protect against races
on a single device, the fact that all devices use the same workqueue,
and flush_workqueue() flushes *everything* from that workqueue, we can
have one device in the middle of a down and holding the rtnl lock and
another totally unrelated device needing to run mcast_restart_task,
which wants the rtnl lock and will loop trying to take it unless is
sees its own FLAG_ADMIN_UP flag go away. Because the unrelated
interface will never see its own ADMIN_UP flag drop, the interface
going down will deadlock trying to flush the queue. There are several
possible solutions to this problem:
Make carrier_on_task and mcast_restart_task try to take the rtnl for
some set period of time and if they fail, then bail. This runs the
real risk of dropping work on the floor, which can end up being its
own separate kind of deadlock.
Set some global flag in the driver that says some device is in the
middle of going down, letting all tasks know to bail. Again, this can
drop work on the floor. I suppose if our own ADMIN_UP flag doesn't go
away, then maybe after a few tries on the rtnl lock we can queue our
own task back up as a delayed work and return and avoid dropping work
on the floor that way. But I'm not 100% convinced that we won't cause
other problems.
Or the method this patch attempts to use, which is when we bring an
interface up, create a workqueue specifically for that interface, so
that when we take it back down, we are flushing only those tasks
associated with our interface. In addition, keep the global
workqueue, but now limit it to only flush tasks. In this way, the
flush tasks can always flush the device specific work queues without
having deadlock issues.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When creating an IPoIB UD QP, provide a hint to the low level driver
that the QP should support flow-steering. This means that privileged
user space applications can steer TCP/IP IPoIB traffic from the
network stack, in a similar manner done with Ethernet RAW_PACKET QPs.
The hint is provided through new QP creation flag called NETIF_QP.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
ipoib_mcast_detach() does nothing except call ib_detach_mcast(), so just
use the core API in the one place that does a multicast group detach.
add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-105 (-105)
function old new delta
ipoib_mcast_leave 357 319 -38
ipoib_mcast_detach 67 - -67
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The current code will set the Q_Key for any join of a non-sendonly
multicast group. The operation involves a modify QP operation, which
is fairly heavyweight, and is only really required after the join of
the broadcast group. Fix this by adding a parameter to ipoib_mcast_attach()
to control when the Q_Key is set.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
No need for a mutex around calls to ib_attach_mcast/ib_detach_mcast
since these operations are synchronized at the HW driver layer.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The patch tries to solve the problem of device going down and paths being
flushed on an SM change event. The method is to mark the paths as candidates for
refresh (by setting the new valid flag to 0), and wait for an ARP
probe a new path record query.
The solution requires a different and less intrusive handling of SM
change event. For that, the second argument of the flush function
changes its meaning from a boolean flag to a level. In most cases, SM
failover doesn't cause LID change so traffic won't stop. In the rare
cases of LID change, the remote host (the one that hadn't changed its
LID) will lose connectivity until paths are refreshed. This is no
worse than the current state. In fact, preventing the device from
going down saves packets that otherwise would be lost.
Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device. This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
They don't get updated by git and so they're worse than useless.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit f56bcd80 ("IPoIB: Use separate CQ for UD send completions")
introduced a bug where the transmit queue could get stopped and never
woken up. The problem is that send completions are only polled at the
end of the xmit function, so if the send queue fills up and the xmit
path stops the queue, then there is no way for send completions to
ever get polled, and so the transmit queue stays stopped forever.
Fix this by arming the send CQ just before posting the last send
request that fills the send queue. Then, when the completion event
handler is called, drain the send CQ. Since it is possible that not
enough send completions are in the CQ, verify that the the net queue
has been woken up after draining the send CQ, and if not arm a timer
and drain again at the timer function.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Use a dedicated CQ for UD send completions. Also, do not arm the UD
send CQ, which reduces the number of interrupts generated. This patch
farther reduces overhead by not calling poll CQ for every posted send
WR -- it does polls only when there 16 or more outstanding work requests.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch enables IPoIB to use 4K UD messages (when the underlying
device and fabrics support a 4K MTU) by using two scatter buffers when
PAGE_SIZE is less than or equal to thhe HCA IB MTU size. The first
buffer is for IPoIB header + GRH header, and the second buffer is the
IPoIB payload, which is 4K-4.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
For HCAs that support TCP segmentation offload (IB_DEVICE_UD_TSO), set
NETIF_F_TSO and use HW LSO to offload TCP segmentation.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets. The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.
We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Some IB adapters (notably IBM's eHCA) do not implement SRQs (shared
receive queues). The current IPoIB connected mode support only works
on devices that support SRQs.
Fix this by adding support for using the receive queue of each
connected mode receive QP. The disadvantage of this compared to using
an SRQ is that it means a full queue of receives must be posted for
each remote connected mode peer, which means that total memory usage
is potentially much higher than when using SRQs. To manage this, add
a new module parameter "max_nonsrq_conn_qp" that limits the number of
connections allowed per interface.
The rest of the changes are fairly straightforward: we use a table of
struct ipoib_cm_rx to hold all the active connections, and put the
table index of the connection in the high bits of receive WR IDs.
This is needed because we cannot rely on the struct ib_wc.qp field for
non-SRQ receive completions. Most of the rest of the changes just
test whether or not an SRQ is available, and post receives or find
received packets in the right place depending on the answer.
Cleaning up dead connections actually becomes simpler, because we do
not have to do the "last WQE reached" dance that is required to
destroy QPs attached to an SRQ. We just move the QP to the error
state and wait for all pending receives to be flushed.
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
[ Completely rewritten and split up, based on Pradeep's work. Several
bugs fixed and no doubt several bugs introduced. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix whitespace blunders, convert "foo* bar" to "foo *bar", etc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipoib_transport_dev_init() calls ipoib_cm_dev_init(), so it needs to
call ipoib_cm_dev_cleanup() to unwind that on the error path.
Found by Dotan Barak of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
SRQ WR leakage has been observed with IPoIB/CM: e.g. flipping ports on
and off will, with time, leak out all WRs and then all connections
will start getting RNR NAKs. Fix this in the way suggested by spec:
move the QP being destroyed to the error state, wait for "Last WQE
Reached" event and then post WR on a "drain QP" connected to the same
CQ. Once we observe a completion on the drain QP, it's safe to call
ib_destroy_qp.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
SM reconfiguration or failover possibly causes a shuffling of the values
in the P_Key table. Right now, IPoIB only queries for the P_Key index
once when it creates the device QP, and hence there are problems if the
index of a P_Key value changes. Fix this by using the PKEY_CHANGE event
to trigger a recheck of the P_Key index.
Signed-off-by: Yosef Etigin <yosefe@voltaire.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
An asynchronous event carries the port number that the event occurred
on, so there's no reason for an IPoIB interface to process an event
associated with a different local HCA port.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The following patch adds experimental support for IPoIB connected
mode, as defined by the draft from the IETF ipoib working group. The
idea is to increase performance by increasing the MTU from the maximum
of 2K (theoretically 4K) supported by IPoIB on top of UD. With this
code, I'm able to get 800MByte/sec or more with netperf without
options on a Mellanox 4x back-to-back DDR system.
Some notes on code:
1. SRQ is used for scalability to large cluster sizes
2. Only RC connections are used (UC does not support SRQ now)
3. Retry count is set to 0 since spec draft warns against retries
4. Each connection is used for data transfers in only 1 direction, so
each connection is either active(TX) or passive (RX). 2 sides that
want to communicate create 2 connections.
5. Each active (TX) connection has a separate CQ for send completions -
this keeps the code simple without CQ resize and other tricks
6. To detect stale passive side connections (where the remote side is
down), we keep an LRU list of passive connections (updated once per
second per connection) and destroy a connection after it has been
unused for several seconds. The LRU rule makes it possible to avoid
scanning connections that have recently been active.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Handle client reregister events by treating them just like LID or
SM changes -- flush all cached paths and rejoin multicast groups.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Make IPoIB's send and receive queue sizes tunable via module
parameters ("send_queue_size" and "recv_queue_size"). This allows the
queue sizes to be enlarged to fix disastrously bad performance on some
platforms and workloads, without bloating memory usage when large
queues aren't needed.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch causes the network interface to respond to P_Key change
events correctly. As a result, you'll see a child interface in the
"RUNNING" state (netif_carrier_on()) only when the corresponding P_Key
is configured by the SM. When SM removes a P_Key, the "RUNNING" state
will be disabled for the corresponding network interface. To
implement this, I added IB_EVENT_PKEY_CHANGE event handling. To
prevent flushing the device before the device is open by the "delay
open" mechanism, I added an additional device flag called
IPOIB_FLAG_INITIALIZED.
This also prevents the child network interface from trying to join to
multicast groups until the PKEY is configured. We used to get error
messages like:
ib0.f2f2: couldn't attach QP to multicast group ff12:401b:f2f2:0:0:0:ffff:ffff
in this case. To fix this, I just check IPOIB_FLAG_OPER_UP flag in
ipoib_set_mcast_list().
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
With the current IPoIB driver, the status of network interfaces stays
"RUNNING" even if the link goes down (for example because a cable is
unplugged). Fix this by flushing the IPoIB interface when the link
goes down.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Move ipoib_ib_dev_flush() to ipoib's workqueue. This keeps it ordered
with respect to other work scheduled by the ipoib driver. This fixes
problems with races, for example:
- ipoib_ib_dev_flush() has started running because of an IB event
- user does ifconfig ib0 down
- ipoib_mcast_stop_thread() gets called twice and waits for the same
completion twice
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
semaphore to mutex conversion by Ingo and Arjan's script.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Sanity-checked on real IB hardware ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Minor cleanups: fix a misleading comment, and get rid of attr_mask
variables that are only used to hold constants (just use the constants
directly).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipoib_create_qp() no longer creates IPoIB's QP, so it shouldn't
destroy the QP on failure -- that unwinding happens elsewhere, so the
current code can cause a double free. While we're at it, the
function's name should match what it actually does, so rename it to
ipoib_init_qp().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Move the InfiniBand headers from drivers/infiniband/include to include/rdma.
This allows InfiniBand-using code to live elsewhere, and lets us remove the
ugly EXTRA_CFLAGS include path from the InfiniBand Makefiles.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Make some lawyers happy and add copyright notices for people who
forgot to include them when they actually touched the code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
