| Age | Commit message (Collapse) | Author |
|---|
|
The driver allocates SRQ WQEs size with a power of 2 size both for
Tavor and for memfree. For Tavor, however, the hardware only requires
the WQE size to be a multiple of 16, not a power of 2, and the max
number of scatter-gather allowed is reported accordingly by the
firmware (and this is the value currently returned by
ib_query_device() and ibv_query_device()).
If the max number of scatter/gather entries reported by the FW is used
when creating an SRQ, the creation will fail for Tavor, since the
required WQE size will be increased to the next power of 2, which
turns out to be larger than the device permitted max WQE size (which
is not a power of 2).
This patch reduces the reported SRQ max wqe size so that it can be used
successfully in creating an SRQ on Tavor HCAs.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When allocating gid_cache, use kmalloc(sizeof *gid_cache, ...) rather
than kmalloc(sizeof *pkey_cache, ...). It doesn't really matter which
one is used, since the size ends up the same either way, but it's much
better to say what we mean.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
We know ipoib_flush_paths() is called from plain process context with
interrupts enabled, since it does wait_for_completion(). So there's
no need to use spin_lock_irqsave() -- spin_lock_irq() is fine.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ib_sa_cancel_query() must be called with priv->lock held since
a completion might arrive and set path->query to NULL.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The PCI spec recommends against drivers playing with a device's PCI
read burst size, and says that systems software should configure it.
And we actually have users that report that changing it from the
default set by BIOS hurts performance and/or stability for them. On
the other hand, the Mellanox Programmer's Reference Manual recommends
turning it up all the way to the maximum value. Some tests conducted
here in the lab do not show performance improvement from this tuning,
but this might be just me.
As a work-around, make this tuning an option, off by default (safe
value), with an eye towards removing it completely one day if no one
complains.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Make IPoIB's send and receive queue sizes tunable via module
parameters ("send_queue_size" and "recv_queue_size"). This allows the
queue sizes to be enlarged to fix disastrously bad performance on some
platforms and workloads, without bloating memory usage when large
queues aren't needed.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipoib_mcast_restart_task() might free an mcast object while a join
request is still outstanding, leading to an oops when the query
completes. Fix this by waiting for query to complete, similar to what
ipoib_stop_thread() is doing. The wait for mcast completion code is
consolidated in wait_for_mcast_join().
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Push translation of static rate to HCA format into low-level drivers,
where it belongs. For static rate encoding, use encoding of rate
field from IB standard PathRecord, with addition of value 0, for
backwards compatibility with current usage. The changes are:
- Add enum ib_rate to midlayer includes.
- Get rid of static rate translation in IPoIB; just use static rate
directly from Path and MulticastGroup records.
- Update mthca driver to translate absolute static rate into the
format used by hardware. This also fixes mthca's static rate
handling for HCAs that are capable of 4X DDR.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Consolidate IPoIB's private neighbour data handling into
ipoib_neigh_alloc() and ipoib_neigh_free(). This will make it easier
to keep track of the neighbour structures that IPoIB is handling, and
is a nice cleanup of the code:
add/remove: 2/1 grow/shrink: 1/8 up/down: 100/-178 (-78)
function old new delta
ipoib_neigh_alloc - 61 +61
ipoib_neigh_free - 36 +36
ipoib_mcast_join_finish 1288 1291 +3
path_rec_completion 575 573 -2
ipoib_mcast_join_task 664 660 -4
ipoib_neigh_destructor 101 92 -9
ipoib_neigh_setup_dev 14 3 -11
ipoib_neigh_setup 17 - -17
path_free 238 215 -23
ipoib_mcast_free 329 306 -23
ipoib_mcast_send 718 684 -34
neigh_add_path 705 650 -55
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix memory leak if parsing destination GID fails.
Coverity bug 1042
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Change the mthca debugging trace output code so that it can enabled
and disabled at runtime with the debug_level module parameter in
sysfs. Also, don't allow CONFIG_INFINIBAND_MTHCA_DEBUG to be disabled
unless CONFIG_EMBEDDED is selected. We want users (and especially
distros) to have this turned on unless they really need to save space,
because by the time we want debugging output, it's usually too late to
rebuild a kernel.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Don't allow CONFIG_INFINIBAND_IPOIB_DEBUG to be disabled unless
CONFIG_EMBEDDED is selected. We want users (and especially distros)
to have this turned on unless they really need to save space, because
by the time we want debugging output, it's usually too late to rebuild
a kernel. The debugging output can be controlled at runtime via the
debug_level module parameter in sysfs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
We have seen the following OOPs in cancel_mads, when restarting opensm
multiple times:
Call Trace:
[<c010549b>] show_stack+0x9b/0xb0
[<c01055ec>] show_registers+0x11c/0x190
[<c01057cd>] die+0xed/0x160
[<c031b966>] do_page_fault+0x3f6/0x5d0
[<c010511f>] error_code+0x4f/0x60
[<f8ac4e38>] cancel_mads+0x128/0x150 [ib_mad]
[<f8ac2811>] unregister_mad_agent+0x11/0x130 [ib_mad]
[<f8ac2a12>] ib_unregister_mad_agent+0x12/0x20 [ib_mad]
[<f8b10f23>] ib_umad_close+0xf3/0x130 [ib_umad]
[<c0162937>] __fput+0x187/0x1c0
[<c01627a9>] fput+0x19/0x20
[<c0160f7a>] filp_close+0x3a/0x60
[<c0121ca8>] put_files_struct+0x68/0xa0
[<c0103cf7>] do_signal+0x47/0x100
[<c0103ded>] do_notify_resume+0x3d/0x40
[<c0103f9e>] work_notifysig+0x13/0x25
We traced this back to local_completions unlocking mad_agent_priv->lock
while still keeping a pointer into local_list. A later call to
list_del(&local->completion_list) would then corrupt the list.
To fix this, remove the entry from local_list after looking it up but
before releasing mad_agent_priv->lock, to prevent cancel_mads from
finding and freeing it.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Integrate the ipath core and OpenIB drivers into the kernel build
infrastructure. Add entry to MAINTAINERS.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The ipath_verbs.c file implements the driver-specific components of the
kernel's Infiniband verbs layer.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Management datagram support, queue pairs, and reliable and unreliable
connections.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Completion queues, local and remote memory keys, and memory region
support.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This is an implementation of the Infiniband RC ("reliable connection")
protocol.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
These files implement the Infiniband UC ("unreliable connection") and UD
("unreliable datagram") protocols.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
These header files are used by the layered Infiniband driver.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The layering interfaces are used to implement the Infiniband protocols
and the ethernet emulation driver.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
These files introduce a char device that userspace apps use to gain
direct memory-mapped access to the InfiniPath hardware, and routines for
pinning and unpinning user memory in cases where the hardware needs to
DMA into the user address space.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The ipathfs filesystem contains files that are not appropriate for
sysfs, because they contain binary data. The hierarchy is simple; the
top-level directory contains driver-wide attribute files, while numbered
subdirectories contain per-device attribute files.
Our userspace code currently expects this filesystem to be mounted on
/ipathfs, but a final location has not yet been chosen.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
EEPROM support, interrupt handling, statistics gathering, and write
combining management for x86_64.
A note regarding i2c: The Atmel EEPROM hardware we use looks like an
i2c device electrically, but is not i2c compliant at all from a
functional perspective. We tried using the kernel's i2c support to
talk to it, but failed.
Normal i2c devices have a single 7-bit or 10-bit i2c address that they
respond to. Valid 7-bit addresses range from 0x03 to 0x77. Addresses
0x00 to 0x02 and 0x78 to 0x7F are special reserved addresses
(e.g. 0x00 is the "general call" address.) The Atmel device, on the
other hand, responds to ALL addresses. It's designed to be the only
device on a given i2c bus. A given i2c device address corresponds to
the memory address within the i2c device itself.
At least one reason why the linux core i2c stuff won't work for this
is that it prohibits access to reserved addresses like 0x00, which are
really valid addresses on the Atmel devices.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipath_init_chip.c sets up an InfiniPath device for use.
ipath_diag.c permits userspace diagnostic tools to read and write a
chip's registers. It is different in purpose from the mmap interfaces
to the /sys/bus/pci resource files.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This file contains routines and definitions specific to InfiniPath
devices that have PCI Express interfaces.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The ipath_ht400.c file contains routines and definitions specific to
HyperTransport-based InfiniPath devices.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipath_common.h and ips_common.h contain definitions shared between
userspace and the kernel.
ipath_kernel.h is the core driver header file.
ipath_debug.h contains mask values used for controlling driver debugging.
ipath_registers.h contains bitmask definitions used in chip registers.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The ipath driver is a low-level driver for PathScale InfiniPath host
channel adapters (HCAs) based on the HT-400 and PE-800 chips, including
the InfiniPath HT-460, the small form factor InfiniPath HT-460, the
InfiniPath HT-470 and the Linux Networx LS/X.
The ipath_driver.c file contains much of the low-level device handling
code.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add RMPP support for additional management classes that support it.
Also, validate RMPP is consistent with management class specified.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Received responses are currently matched against sent requests based
on TID only. According to the spec, responses should match based on
the combination of TID, management class, and requester LID/GID.
Without the additional qualification, an agent that is responding to
two requests, both of which have the same TID, can match RMPP ACKs
with the incorrect transaction. This problem can occur on the SM node
when responding to SA queries.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Quite a few cleanup functions in mthca were marked as __devexit.
However, they could also be called from error paths during
initialization, so they cannot be marked that way. Just delete all of
the incorrect annotations.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipoib_hard_header() needs to handle the case that daddr is NULL. This
can happen when packets are injected via a raw socket, and IPoIB
shouldn't oops in this case.
Reported by Anton Blanchard <anton@samba.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The previous patch for Tavor broke MemFree logic.
The driver should perform limit check only for Tavor. For MemFree,
the check is incorrect, since ds (WQE stride) is always a power-of-2
(although the max_desc_size may not be).
In Tavor, however, WQE stride and desc_size are the same, and are not
necessarily power-of-2. The check was really for the WQE stride (and
it Tavor, we use max_desc_size for the stride).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The recently merged patch to create a fake scatterlist for non-SG SCSI
commands had a bug: the driver ended up doing dma_unmap_sg() on a
scatterlist scmnd->request_buffer rather than the fake scatter list it
created. Fix this so that the driver unmaps the same thing it maps.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch causes the network interface to respond to P_Key change
events correctly. As a result, you'll see a child interface in the
"RUNNING" state (netif_carrier_on()) only when the corresponding P_Key
is configured by the SM. When SM removes a P_Key, the "RUNNING" state
will be disabled for the corresponding network interface. To
implement this, I added IB_EVENT_PKEY_CHANGE event handling. To
prevent flushing the device before the device is open by the "delay
open" mechanism, I added an additional device flag called
IPOIB_FLAG_INITIALIZED.
This also prevents the child network interface from trying to join to
multicast groups until the PKEY is configured. We used to get error
messages like:
ib0.f2f2: couldn't attach QP to multicast group ff12:401b:f2f2:0:0:0:ffff:ffff
in this case. To fix this, I just check IPOIB_FLAG_OPER_UP flag in
ipoib_set_mcast_list().
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
If the call to mthca_MODIFY_QP() failed, then mthca_modify_qp() would
still do some things it shouldn't, such as store away attributes for
special QPs. Fix this, and simplify the code, by simply jumping to
the exit path if mthca_MODIFY_QP() fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
With the current IPoIB driver, the status of network interfaces stays
"RUNNING" even if the link goes down (for example because a cable is
unplugged). Fix this by flushing the IPoIB interface when the link
goes down.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix some whitespace damage (indenting with spaces) that snuck in.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
mthca_alloc_sqp() by mthca_set_qp_size() need to set qp->transport
before calling mthca_set_qp_size(), since the value is used there.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When setting the shared receive queue (SRQ) watermark in a modify SRQ
operation, make sure that the supplied value is not larger than the
full size of the SRQ.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Guarantee the calculated work queue entry size does not exceed the max
allowable WQE size when creating an SRQ. This is a problem with Arbel
in Tavor-compatibility mode because the current WQE size computation
method rounds up to next power of 2.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add a check that the modify QP parameters sgid_index and path_mtu are
valid, since they might come from userspace.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Since the SCSI midlayer is moving towards entirely getting rid of
commands with use_sg == 0, we should treat this case as an exception.
Therefore, change the IB SRP initiator to create a fake scatterlist
for these commands with sg_init_one(). This simplifies the flow of
DMA mapping and unmapping, since SRP can just use dma_map_sg() and
dma_unmap_sg() unconditionally, rather than having to choose between
the dma_{map,unmap}_sg() and dma_{map,unmap}_single() variants.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipoib_ib_dev_flush() should get passed cpriv->dev, not &cpriv->dev.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (235 commits)
[NETFILTER]: Add H.323 conntrack/NAT helper
[TG3]: Don't mark tg3_test_registers() as returning const.
[IPV6]: Cleanups for net/ipv6/addrconf.c (kzalloc, early exit) v2
[IPV6]: Nearly complete kzalloc cleanup for net/ipv6
[IPV6]: Cleanup of net/ipv6/reassambly.c
[BRIDGE]: Remove duplicate const from is_link_local() argument type.
[DECNET]: net/decnet/dn_route.c: fix inconsequent NULL checking
[TG3]: make drivers/net/tg3.c:tg3_request_irq() static
[BRIDGE]: use LLC to send STP
[LLC]: llc_mac_hdr_init const arguments
[BRIDGE]: allow show/store of group multicast address
[BRIDGE]: use llc for receiving STP packets
[BRIDGE]: stp timer to jiffies cleanup
[BRIDGE]: forwarding remove unneeded preempt and bh diasables
[BRIDGE]: netfilter inline cleanup
[BRIDGE]: netfilter VLAN macro cleanup
[BRIDGE]: netfilter dont use __constant_htons
[BRIDGE]: netfilter whitespace
[BRIDGE]: optimize frame pass up
[BRIDGE]: use kzalloc
...
|
|
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct neigh_ops currently has a destructor field, which no in-kernel
drivers outside of infiniband use. The infiniband/ulp/ipoib in-tree
driver stashes some info in the neighbour structure (the results of
the second-stage lookup from ARP results to real link-level path), and
it uses neigh->ops->destructor to get a callback so it can clean up
this extra info when a neighbour is freed. We've run into problems
with this: since the destructor is in an ops field that is shared
between neighbours that may belong to different net devices, there's
no way to set/clear it safely.
The following patch moves this field to neigh_parms where it can be
safely set, together with its twin neigh_setup. Two additional
patches in the patch series update ipoib to use this new interface.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix endianness handling of srq_limit: it is big-endian in the context
structure, so we need to swab it before returning it.
Also add support for srq_limit query for Tavor (non-MemFree) HCAs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
In neigh_add_path(), the queue of delayed packets can never be full,
because the queue is always freshly created and cannot be found by any
other code path. In fact, the test of the queue length is worse than
useless: if somehow the test ever triggered and path_rec_start() also
failed, then dev_kfree_skb_any() will be called twice on the same skb.
Fix this by deleting the useless test. Pointed out by Michael
S. Tsirkin <mst@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
