| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit d3b421cd07e4c0d4d6c0bbd55ca169c054fc081d ]
Under some conditions, irq sorting procedure used by INTC can go wrong
resulting in a spurious irq getting reported.
If this condition is not handled, it results in endless stream of:
unexpected IRQ trap at vector 00
messages from ack_bad_irq()
Handle the spurious interrupt condition in omap-intc driver to prevent this.
Measurements using kernel function profiler on AM335x EVM running at 720MHz
show that after this patch omap_intc_handle_irq() takes about 37.4us against
34us before this patch.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/9c78a6db02ac55f7af7371b417b6e414d2c3095b.1450188128.git.nsekhar@ti.com
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 6ed3464897cc825a75218653c710d673282dfcf8 ]
As it turns out the current IRQ number will *always* be available from
SIR register which renders the reads of PENDING registers as plain
unnecessary overhead.
In order to catch any situation where SIR reads as zero, we're adding
a WARN() to turn it into a very verbose error and users actually
report it.
With this patch average running time of omap_intc_handle_irq() reduced
from about 28.5us to 19.8us as measured by the kernel function
profiler.
Tested with BeagleBoneBlack Rev A5C.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: Linux ARM Kernel Mailing List <linux-arm-kernel@lists.infradead.org>
Link: http://lkml.kernel.org/r/20150720204910.GH5394@saruman.tx.rr.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 49f34134aea74f19ca016f055d25ee55ec359dee ]
Atmel AIC has common structure for SMR (Source Mode Register).
bit[6:5] Interrupt source type
bit[2:0] Priority level
Other bits are unused.
To update new priority value, bit[2:0] should be cleared first and then
new priority level can be written. However, aic_common_set_priority()
helper clears source type bits instead of priority bits.
This patch fixes wrong mask bit operation.
Fixes: b1479ebb7720 "irqchip: atmel-aic: Add atmel AIC/AIC5 drivers"
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Nicholas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org #v3.17+
Link: http://lkml.kernel.org/r/1452669592-3401-2-git-send-email-milo.kim@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
commit 209da39154837ec1b69fb34f438041939911e4b4 upstream.
The LIC doesn't deal with the different types of interrupts itself
but needs to forward calls to set the appropriate type to its parent
IRQ controller.
Without this fix all IRQs routed through the LIC will stay at the
initial EDGE type, while most of them should actually be level triggered.
Fixes: 1eec582158e2 "irqchip: tegra: Add Tegra210 support"
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1445787552-13062-1-git-send-email-dev@lynxeye.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a9a8915c8888b615521b17d70a4342187eae60b upstream.
When the ITS is configured for non-cacheable transactions, make sure
that the allocated, zeroed memory is flushed to the Point of
Coherency, allowing the ITS to observe the zeros instead of random
garbage (or even get its own data overwritten by zeros being evicted
from the cache...).
Fixes: 241a386c7dbb "irqchip: gicv3-its: Use non-cacheable accesses when no shareability"
Reported-and-tested-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Pavel Fedin <p.fedin@samsung.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1442142873-20213-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d32dc9aa10c739363c775baf4499416b2e0dc11f upstream.
When masking/unmasking interrupts, mask_cache is updated and used later
for suspend/resume. Unfortunately, it always was the mask_cache
associated with the first irq chip which was updated. So when performing
resume, only irqs 0-31 could be enabled.
Fixes: b1479ebb7720 ("irqchip: atmel-aic: Add atmel AIC/AIC5 drivers")
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <sasha.levin@oracle.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <nicolas.ferre@atmel.com>
Cc: <alexandre.belloni@free-electrons.com>
Cc: <boris.brezillon@free-electrons.com>
Cc: <Wenyou.Yang@atmel.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1442843173-2390-1-git-send-email-ludovic.desroches@atmel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8200fe4347870d4ad6475048bcdf3e7c106c5268 upstream.
The TI crossbar irqchip doesn't provides any facility to configure the
wakeup sources, but the conversion to hierarchical irqdomains set the
irq_set_wake callback to irq_chip_set_wake_parent. The parent chip
(OMAP wakeupgen) has no irq_set_wake function either so the call will
fail with -ENOSYS. As a result the irq_set_wake() call in the resume
path will trigger an 'Unbalanced wake disable' warning.
Before the conversion the GIC irqchip was the top level irqchip and
correctly flagged with IRQCHIP_SKIP_SET_WAKE.
Restore the correct behaviour by removing the irq_set_type callback
from the crossbar irqchip and set the IRQCHIP_SKIP_SET_WAKE flag which
lets the irq_set_irq_wake() call from the driver succeed.
[ tglx: Massaged changelog ]
Fixes: 783d31863fb8 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1439554830-19502-7-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fd8f47e7e5b64a74b60f23c2e08ba8234d659d1 upstream.
The ARM GIC requires that all interrupts which are not used as a
wakeup source have to be masked during suspend.
The conversion of the crossbar irqchip to hierarchical irq domains
failed to mark the crossbar irqchip with the IRQCHIP_MASK_ON_SUSPEND
flag and therefor broke the suspend requirement of the GIC.
Before the conversion the flags were visible because the GIC was the
top level irqchip. After the conversion the crossbar irqchip is the
top level irq chip whose flags are evaluated in suspend_device_irq().
As the flag is not set the masking of the non-wakeup irqs is not
invoked which breaks suspend.
Add the IRQCHIP_MASK_ON_SUSPEND flag to the crossbar irqchip, so the
GIC interrupts get masked properly.
[ tglx: Massaged changelog ]
Fixes: 783d31863fb8 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1439554830-19502-6-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e269ec42328783e51be08c191aa935dba56141fc upstream.
The conversion of the crossbar irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The crossbar irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the crossbar irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 783d31863fb8 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1439554830-19502-4-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 591e5bec13f15feb13fc445b6c9c59954711c4ac upstream.
The GICv3 ITS architecture allows a given [DevID, EventID] pair to be
translated to a [LPI, Collection] pair, where DevID is the device writing
the MSI, EventID is the payload being written, LPI is the actual
interrupt number, and Collection is roughly equivalent to a target CPU.
Each LPI can be mapped to a separate collection, but the ITS driver
insists on maintaining the collection on a device basis, instead of doing
it on a per interrupt basis.
This is obviously flawed, and this patch fixes it by adding a per interrupt
index that indicates which collection number is in use.
Reported-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1437126402-11677-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull more MIPS fixes from Ralf Baechle:
"Another round of 4.1 MIPS fixes, one fix to a MIPS-specific #if
condition in lib/mpi, one fix to the MIPS GIC irqchip driver and one
SSB fix.
Details:
- fix handling of clock in chipco SSB driver.
- fix two MIPS-specific #if conditions to correctly work for GCC 5.1.
- fix damage to R6 pgtable bits done by XPA support.
- fix possible crash due to unloading modules that contain statically
defined platform devices.
- fix disabling of the MSA ASE on context switch to also work
correctly when a new thread/process has the CPU for the very first
time.
This is part of linux-next and has been beaten to death on
Imagination's test farm.
While things are not looking too grim this pull request also means the
rate of fixes for 4.1 remains nearly constant so I'd not be unhappy if
you'd delay the release"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MPI: MIPS: Fix compilation error with GCC 5.1
IRQCHIP: mips-gic: Don't nest calls to do_IRQ()
MIPS: MSA: bugfix - disable MSA correctly for new threads/processes.
MIPS: Loongson: Do not register 8250 platform device from module.
MIPS: Cobalt: Do not build MTD platform device registration code as module.
SSB: Fix handling of ssb_pmu_get_alp_clock()
MIPS: pgtable-bits: Fix XPA damage to R6 definitions.
|
|
The GIC chained handlers use do_IRQ() to call the subhandlers. This
means that irq_enter() calls get nested, which leads to preempt count
looking like we're in nested interrupts, which in turn leads to all
system time being accounted as IRQ time in account_system_time().
Fix it by using generic_handle_irq(). Since these same functions are
used in some systems (if cpu_has_veic) from a low-level vectored
interrupt handler which does not go throught do_IRQ(), we need to do it
conditionally.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Patchwork: https://patchwork.linux-mips.org/patch/10545/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fixes: 6058bb362818 'ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller'
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1433684009.9134.1.camel@ingics.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When allocating a device table, if the requested allocation is smaller
than the default granule size of the ITS then, we need to round up to
the default size.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
[ stuart: Added comments and massaged changelog ]
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Reviewed-by: Marc Zygnier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1432134795-661-1-git-send-email-stuart.yoder@freescale.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The irq chip functions use the irq chipdata directly as the base register
address of the controller, so this should be passed in instead of a pointer
to the array address holding the base address.
This fixes Tegra20 CPUidle as now the un-/masking of IRQs at the LIC level
works again, but more importantly it fixes the resulting memory corruption.
Fixes: de3ce0804916 ' irqchip: tegra: Add DT-based support for legacy interrupt controller'
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1431202014-3136-1-git-send-email-dev@lynxeye.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Two patches from the irq departement:
- a simple fix to make dummy_irq_chip usable for wakeup scenarios
- removal of the gic arch_extn hackery. Now that all users are
converted we really want to get rid of the interface so people wont
come up with new use cases"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: gic: Drop support for gic_arch_extn
genirq: Set IRQCHIP_SKIP_SET_WAKE flag for dummy_irq_chip
|
|
Now that the users of gic_arch_extn have been fixed, drop the
"feature" for good. This leads to the removal of some now useless
locking.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
|
|
git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core change for v4.1 (round 3) from Jason Cooper
Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
|
|
git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core changes for v4.1 (round 2) from Jason Cooper
- gic
- Tolerate uni-processor systems better in gic_get_cpumask()
- mvebu
- Handle per-cpu interrupts properly
- Enable PMU interrupts
- Enable wakeup source
- vybrid
- Add MSCM interrupt router
- renesas
- Add PM and wakeup support
|
|
Conflicts:
drivers/irqchip/irq-gic.c
|
|
|
|
|
|
into irq/core
irqchip core changes for v4.0 from Jason Cooper
- ST
- New driver, irq-st
- Renesas
- Use u32 type for 32bit regs
|
|
Add the required hooks for the internal state of an interrupt
to be exposed to other subsystems.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Phong Vo <pvo@apm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tin Huynh <tnhuynh@apm.com>
Cc: Y Vo <yvo@apm.com>
Cc: Toan Le <toanle@apm.com>
Cc: Bjorn Andersson <bjorn@kryo.se>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1426676484-21812-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Add the required hooks for the internal state of an interrupt
to be exposed to other subsystems.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Phong Vo <pvo@apm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tin Huynh <tnhuynh@apm.com>
Cc: Y Vo <yvo@apm.com>
Cc: Toan Le <toanle@apm.com>
Cc: Bjorn Andersson <bjorn@kryo.se>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1426676484-21812-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
|
|
|
|
The IRQC module clock is managed through Runtime PM and PM Domains.
If wake-up is enabled, this clock must not be disabled during system
suspend.
Hence implement irq_chip.irq_set_wake(), which increments/decrements the
clock's enable_count when needed.
This fixes wake-up by gpio-keys on r8a73a4/ape6evm.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lkml.kernel.org/r/1427889606-18671-1-git-send-email-geert+renesas@glider.be
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
On the Armada 370/XP SoCs, in standby mode the SoC stay powered and it
is possible to wake-up from any interrupt sources. This patch adds
flag to the MPIC irqchip driver to let linux know this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1427724278-12379-5-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This is the main peripheral IRQ controller on the BCM7xxx MIPS chips;
it has the following characteristics:
- 64 to 160+ level IRQs
- Atomic set/clear registers
- Reasonably predictable register layout (N status words, then N
mask status words, then N mask set words, then N mask clear words)
- SMP affinity supported on most systems
- Typically connected to MIPS IRQ 2,3,2,3 on CPUs 0,1,2,3
This driver registers one IRQ domain and one IRQ chip to cover all
instances of the block. Up to 4 instances of the block may appear, as
it supports 4-way IRQ affinity on BCM7435.
The same block exists on the ARM BCM7xxx chips, but typically the ARM GIC
is used instead. So this driver is primarily intended for MIPS STB chips.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8844/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
These controllers support multiple enable/status pairs (64+ IRQs),
can put the enable/status words at different offsets, and do not
support multiple parent IRQs.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8843/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The BCM7xxx instances of this block (listed in the register manual as
simply "IRQ0") all have the following items in common:
- brcm,int-map-mask: for routing different bits in the L2 to different
parent IRQs
- brcm,int-fwd-mask: for hardwiring certain IRQs to bypass the L2 and
use dedicated L1 lines
- one enable/status pair (32 bits only)
Much of the driver code can be shared with BCM3380-style controllers, but
in order to do this cleanly, let's split out the BCM7xxx-specific logic
first.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Currently the driver assumes that REG_BASE+0x00 is the IRQ enable mask,
and REG_BASE+0x04 is the IRQ status mask. This is true on BCM3384 and
BCM7xxx, but it is not true for some of the controllers found on BCM63xx
chips. So we will change a couple of key assumptions:
- Don't assume that both the IRQEN and IRQSTAT registers will be
covered by a single ioremap() operation.
- Don't assume any particular ordering (IRQSTAT might show up before
IRQEN on some chips).
- For an L2 controller with >=64 IRQs, don't assume that every
IRQEN/IRQSTAT pair will use the same register spacing.
This patch changes the "plumbing" but doesn't yet provide a way for users
to instantiate a controller with arbitrary IRQEN/IRQSTAT offsets.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Wakeable interrupts might be pending at boot/init time, because wakeup
interrupts might have triggered a resume from S5. So don't clear such
wakeups.
This means that any driver which requests a wakeable interrupt bit
should be prepared to handle an interrupt as soon as they call
request_irq(). (This is technically already the correct development
practice, but some drivers probably expect not to receive interrupts
until they have performed some I/O.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8840/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We add new functions to start and stop the GIC counter since there are no
guarantees the counter will be running after a CPU reset. The GIC counter
is stopped by setting the 29th bit on the GIC Config register and it is
started by clearing that bit.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add a function to the MIPS GIC driver for retrieving the Fast Debug
Channel (FDC) interrupt number, similar to the existing ones for the
timer and perf counter interrupts. This will be used by platform
implementations of get_c0_fdc_int() if a GIC is present.
A workaround exists for interAptiv and proAptiv which claim to be able
to route the FDC interrupt but don't seem to be able to in practice (at
least on Malta).
[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9142/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Treat the Fast Debug Channel (FDC) interrupt the same as the timer and
performance counter interrupts. Like them, the FDC IRQ is also per-VPE,
and also doesn't use a per-CPU device ID yet. Per-CPU device IDs don't
seem to work with IRQF_SHARED which is needed for compatibility with
cores which don't route the FDC IRQ through the GIC. For hardware which
routes FDC IRQs through the GIC this is something that could be added
later.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9141/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fix typo in comment in gic_get_c0_perfcount_int:
"erformance" -> "performance".
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Patchwork: https://patchwork.linux-mips.org/patch/9126/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We add new functions to start and stop the GIC counter since there are no
guarantees the counter will be running after a CPU reset. The GIC counter
is stopped by setting the 29th bit on the GIC Config register and it is
started by clearing that bit.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Link: https://lkml.kernel.org/r/1427113923-9840-2-git-send-email-markos.chandras@imgtec.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Tegra210 uses the same legacy interrupt controller as older generations
but it adds a sixth instance.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lkml.kernel.org/r/1427106379-14037-1-git-send-email-thierry.reding@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
|
|
If the ITS or the redistributors report their shareability as zero,
then it is important to make sure they will no generate any cacheable
traffic, as this is unlikely to produce the expected result.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The ITS driver sometime mixes up the use of GICR_PROPBASE bitfields
for the GICR_PENDBASE register, and GITS_BASER for GICR_CBASE.
This does not lead to any observable bug because similar bits are
at the same location, but this just make the code even harder to
understand...
This patch provides the required #defines and fixes the mixup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When building ITS commands which have the device ID in it, we
should mask off the whole upper 32 bits of the first command word
before inserting the new value in there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
With a monolithic GICv3, redistributors are addressed using a linear
number, while a distributed implementation uses physical addresses.
When encoding a target address into a command, we strip the lower
16 bits, as redistributors are always 64kB aligned. This works
perfectly well with a distributed implementation, but has the
silly effect of always encoding target 0 in the monolithic case
(unless you have more than 64k CPUs, of course).
The obvious fix is to shift the linear target number by 16 when
computing the target address, so that we don't loose any precious
bit.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The code deployed to implement GSI linux IRQ numbers mapping on arm64 turns
out to be generic enough so that it can be moved to ACPI core code along
with its respective config option ACPI_GENERIC_GSI selectable on
architectures that can reuse the same code.
Current ACPI IRQ mapping code is not integrated in the kernel IRQ domain
infrastructure, in particular there is no way to look-up the
IRQ domain associated with a particular interrupt controller, so this
first version of GSI generic code carries out the GSI<->IRQ mapping relying
on the IRQ default domain which is supposed to be always set on a
specific architecture in case the domain structure passed to
irq_create/find_mapping() functions is missing.
This patch moves the arm64 acpi functions that implement the gsi mappings:
acpi_gsi_to_irq()
acpi_register_gsi()
acpi_unregister_gsi()
to ACPI core code. Since the generic GSI<->domain mapping is based on IRQ
domains, it can be extended as soon as a way to map an interrupt
controller to an IRQ domain is implemented for ACPI in the IRQ domain
layer.
x86 and ia64 code for GSI mappings cannot rely on the generic GSI
layer at present for legacy reasons, so they do not select the
ACPI_GENERIC_GSI config options and keep relying on their arch
specific GSI mapping layer.
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
ACPI kernel uses MADT table for proper GIC initialization. It needs to
parse GIC related subtables, collect CPU interface and distributor
addresses and call driver initialization function (which is hardware
abstraction agnostic). In a similar way, FDT initialize GICv1/2.
NOTE: This commit allow to initialize GICv1/2 basic functionality.
While now simple GICv2 init call is used, any further GIC features
require generic infrastructure for proper ACPI irqchip initialization.
That mechanism and stacked irqdomains to support GICv2 MSI/virtualization
extension, GICv3/4 and its ITS are considered as next steps.
CC: Jason Cooper <jason@lakedaemon.net>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
