| Age | Commit message (Collapse) | Author |
|---|
|
commit d01552a76d71f9879af448e9142389ee9be6e95b upstream.
This reverts commit 7eb418851f3278de67126ea0c427641ab4792c57.
This commit is poorly justified, I can find not discusison in email,
and it clearly causes a problem.
If a device which is being recovered fails and is subsequently
re-added to an array, there could easily have been changes to the
array *before* the point where the recovery was up to. So the
recovery must start again from the beginning.
If a spare is being recovered and fails, then when it is re-added we
really should do a bitmap-based recovery up to the recovery-offset,
and then a full recovery from there. Before this reversion, we only
did the "full recovery from there" which is not corect. After this
reversion with will do a full recovery from the start, which is safer
but not ideal.
It will be left to a future patch to arrange the two different styles
of recovery.
Reported-and-tested-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: 7eb418851f32 ("md: allow a partially recovered device to be hot-added to an array.")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8a9d66d043ffac116100775a469f05f5158c16f upstream.
After commit 566c09c53455 ("raid5: relieve lock contention in get_active_stripe()")
__find_stripe() is called under conf->hash_locks + hash.
But handle_stripe_clean_event() calls remove_hash() under
conf->device_lock.
Under some cirscumstances the hash chain can be circuited,
and we get an infinite loop with disabled interrupts and locked hash
lock in __find_stripe(). This leads to hard lockup on multiple CPUs
and following system crash.
I was able to reproduce this behavior on raid6 over 6 ssd disks.
The devices_handle_discard_safely option should be set to enable trim
support. The following script was used:
for i in `seq 1 32`; do
dd if=/dev/zero of=large$i bs=10M count=100 &
done
neilb: original was against a 3.x kernel. I forward-ported
to 4.3-rc. This verison is suitable for any kernel since
Commit: 59fc630b8b5f ("RAID5: batch adjacent full stripe write")
(v4.1+). I'll post a version for earlier kernels to stable.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Fixes: 566c09c53455 ("raid5: relieve lock contention in get_active_stripe()")
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 681ab4696062f5aa939c9e04d058732306a97176 upstream.
This was introduced with 9e882242c6193ae6f416f2d8d8db0d9126bd996b
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 203d27b0226a05202438ddb39ef0ef1acb14a759 upstream.
This was introduced with 9e882242c6193ae6f416f2d8d8db0d9126bd996b
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4dcb8b57df3593dcb20481d9d6cf79d1dc1534be upstream.
btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.
Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2871c69e025e8bc507651d5a9cf81a8a7da9d24b upstream.
Commit 4c7e309340ff ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().
The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them. If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.
Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.
Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.c
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba30670f4d5292c4e7f7980bbd5071f7c4794cdd upstream.
Fixes: ac8c3f3df ("dm thin: generate event when metadata threshold passed")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2bffa1503c5c06192eb1459180fac4416575a966 upstream.
The cleaner policy doesn't make use of the per cache block hint space in
the metadata (unlike the other policies). When switching from the
cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block)
was observed. The crash was caused by bugs in dm-cache-metadata.c
when trying to skip creation of the hint btree.
The minimal fix is to change hint size for the cleaner policy to 4 bytes
(only hint size supported).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a708cff93f1845b9239bc7d6310aef54e716c6a upstream.
__dm_destroy() takes io_barrier SRCU lock (dm_get_live_table) and
suspend_lock in reverse order. Doing so can cause AB-BA deadlock:
__dm_destroy dm_swap_table
---------------------------------------------------
mutex_lock(suspend_lock)
dm_get_live_table()
srcu_read_lock(io_barrier)
dm_sync_table()
synchronize_srcu(io_barrier)
.. waiting for dm_put_live_table()
mutex_lock(suspend_lock)
.. waiting for suspend_lock
Fix this by taking the locks in proper order.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Fixes: ab7c7bb6f4ab ("dm: hold suspend_lock while suspending device during device deletion")
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da6fb7a9e5bd6f04f7e15070f630bdf1ea502841 upstream.
Passing -1 to bitmap_storage_alloc() causes page->index to be set to
-1, which is quite problematic.
So only pass ->cluster_slot if mddev_is_clustered().
Fixes: b97e92574c0b ("Use separate bitmaps for each nodes in the cluster")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 042745ee53a0a7c1f5aff191a4a24213c6dcfb52 upstream.
Commit 3a0f9aaee028 ("dm raid: round region_size to power of two")
intended to make sure that the default region size is a power of two.
However, the logic in that commit is incorrect and sets the variable
region_size to 0 or 1, depending on whether min_region_size is a power
of two.
Fix this logic, using roundup_pow_of_two(), so that region_size is
properly rounded up to the next power of two.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 3a0f9aaee028 ("dm raid: round region_size to power of two")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66eefe5de11db1e0d8f2edc3880d50e7c36a9d43 upstream.
Calling e.g. blk_queue_max_hw_sectors() after calls to
disk_stack_limits() discards the settings determined by
disk_stack_limits().
So we need to make those calls first.
Fixes: 199dc6ed5179 ("md/raid0: update queue parameter in a safer location.")
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 199dc6ed5179251fa6158a461499c24bdd99c836 upstream.
When a (e.g.) RAID5 array is reshaped to RAID0, the updating
of queue parameters (e.g. max number of sectors per bio) is
done in the wrong place.
It should be part of ->run, but it is actually part of ->takeover.
This means it happens before level_store() calls:
blk_set_stacking_limits(&mddev->queue->limits);
and so it ineffective. This can lead to errors from underlying
devices.
So move all the relevant settings out of create_stripe_zones()
and into raid0_run().
As this can lead to a bug-on it is suitable for any -stable
kernel which supports reshape to RAID0. So 2.6.35 or later.
As the bug has been present for five years there is no urgency,
so no need to rush into -stable.
Fixes: 9af204cf720c ("md: Add support for Raid5->Raid0 and Raid10->Raid0 takeover")
Reported-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0dc3c8bc157c60b1d470163882be8c13e1950af upstream.
When using nested btrees, the top leaves of the top levels contain
block addresses for the root of the next tree down. If we shadow a
shared leaf node the leaf values (sub tree roots) should be incremented
accordingly.
This is only an issue if there is metadata sharing in the top levels.
Which only occurs if metadata snapshots are being used (as is possible
with dm-thinp). And could result in a block from the thinp metadata
snap being reused early, thus corrupting the thinp metadata snap.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 586b286b110e94eb31840ac5afc0c24e0881fe34 upstream.
Setting the dm-crypt device's max_segment_size to PAGE_SIZE is an
unfortunate constraint that is required to avoid the potential for
exceeding dm-crypt's underlying device's max_segments limits -- due to
crypt_alloc_buffer() possibly allocating pages for the encryption bio
that are not as physically contiguous as the original bio.
It is interesting to note that this problem was already fixed back in
2007 via commit 91e106259 ("dm crypt: use bio_add_page"). But Linux 4.0
commit cf2f1abfb ("dm crypt: don't allocate pages for a partial
request") regressed dm-crypt back to _not_ using bio_add_page(). But
given dm-crypt's cpu parallelization changes all depend on commit
cf2f1abfb's abandoning of the more complex io fragments processing that
dm-crypt previously had we cannot easily go back to using
bio_add_page().
So all said the cleanest way to resolve this issue is to fix dm-crypt to
properly constrain the original bios entering dm-crypt so the encryption
bios that dm-crypt generates from the original bios are always
compatible with the underlying device's max_segments queue limits.
It should be noted that technically Linux 4.3 does _not_ need this fix
because of the block core's new late bio-splitting capability. But, it
is reasoned, there is little to be gained by having the block core split
the encrypted bio that is composed of PAGE_SIZE segments. That said, in
the future we may revert this change.
Fixes: cf2f1abfb ("dm crypt: don't allocate pages for a partial request")
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=104421
Suggested-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee5d004fd0591536a061451eba2b187092e9127c upstream.
The 'event_work' worker used by dm-raid may still be running
when the array is stopped. This can result in an oops.
So flush the workqueue on which it is run after detaching
and before destroying the device.
Reported-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: 9d09e663d550 ("dm: raid456 basic support")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 299b0685e31c9f3dcc2d58ee3beca761a40b44b3 upstream.
'reshape_position' tracks where in the reshape we have reached.
'reshape_safe' tracks where in the reshape we have safely recorded
in the metadata.
These are compared to determine when to update the metadata.
So it is important that reshape_safe is initialised properly.
Currently it isn't. When starting a reshape from the beginning
it usually has the correct value by luck. But when reducing the
number of devices in a RAID10, it has the wrong value and this leads
to the metadata not being updated correctly.
This can lead to corruption if the reshape is not allowed to complete.
This patch is suitable for any -stable kernel which supports RAID10
reshape, which is 3.5 and later.
Fixes: 3ea7daa5d7fd ("md/raid10: add reshape support")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49895bcc7e566ba455eb2996607d6fbd3447ce16 upstream.
I have a report of drop_one_stripe() called from
raid5_cache_scan() apparently finding ->max_nr_stripes == 0.
This should not be allowed.
So add a test to keep max_nr_stripes above min_nr_stripes.
Also use a 'mask' rather than a 'mod' in drop_one_stripe
to ensure 'hash' is valid even if max_nr_stripes does reach zero.
Fixes: edbe83ab4c27 ("md/raid5: allow the stripe_cache to grow and shrink.")
Reported-by: Tomas Papan <tomas.papan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d5b569b665ea6d0b15c52529ff06300de81a7ce upstream.
Cache size can grow or shrink due to various pressures at
any time. So when we resize the cache as part of a 'grow'
operation (i.e. change the size to allow more devices) we need
to blocks that automatic growing/shrinking.
So introduce a mutex. auto grow/shrink uses mutex_trylock()
and just doesn't bother if there is a blockage.
Resizing the whole cache holds the mutex to ensure that
the correct number of new stripes is allocated.
This bug can result in some stripes not being freed when an
array is stopped. This leads to the kmem_cache not being
freed and a subsequent array can try to use the same kmem_cache
and get confused.
Fixes: edbe83ab4c27 ("md/raid5: allow the stripe_cache to grow and shrink.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f518ad0a212e2a6fd68630e176af1de395070a7 upstream.
The device details and mapping trees were just being decremented
before. Now btree_del() is called to do a deep delete.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd4aaf8f9b85d6b2df3231fd62b219ebb75d3568 upstream.
A DM regression on 32 bit systems was reported against v4.2-rc3 here:
https://lkml.org/lkml/2015/7/29/401
Fix this by reverting both commit 1c220c69 ("dm: fix casting bug in
dm_merge_bvec()") and 148e51ba ("dm: improve documentation and code
clarity in dm_merge_bvec"). This combined revert is done to eliminate
the possibility of a partial revert in stable@ kernels.
In hindsight the correct fix, at the time 1c220c69 was applied to fix
the regression that 148e51ba introduced, should've been to simply revert
148e51ba.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Tested-by: Adam Williamson <awilliam@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
inconsistencies
commit 423f04d63cf421ea436bcc5be02543d549ce4b28 upstream.
raid1_end_read_request() assumes that the In_sync bits are consistent
with the ->degaded count.
raid1_spare_active updates the In_sync bit before the ->degraded count
and so exposes an inconsistency, as does error()
So extend the spinlock in raid1_spare_active() and error() to hide those
inconsistencies.
This should probably be part of
Commit: 34cab6f42003 ("md/raid1: fix test for 'was read error from
last working device'.")
as it addresses the same issue. It fixes the same bug and should go
to -stable for same reasons.
Fixes: 76073054c95b ("md/raid1: clean up read_balance.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b6878d9e03043695dbf3fa1caa6dfc09db225b16 upstream.
In drivers/md/md.c get_bitmap_file() uses kmalloc() for creating a
mdu_bitmap_file_t called "file".
5769 file = kmalloc(sizeof(*file), GFP_NOIO);
5770 if (!file)
5771 return -ENOMEM;
This structure is copied to user space at the end of the function.
5786 if (err == 0 &&
5787 copy_to_user(arg, file, sizeof(*file)))
5788 err = -EFAULT
But if bitmap is disabled only the first byte of "file" is initialized
with zero, so it's possible to read some bytes (up to 4095) of kernel
space memory from user space. This is an information leak.
5775 /* bitmap disabled, zero the first byte and copy out */
5776 if (!mddev->bitmap_info.file)
5777 file->pathname[0] = '\0';
Signed-off-by: Benjamin Randazzo <benjamin@randazzo.fr>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34cab6f42003cb06f48f86a86652984dec338ae9 upstream.
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 76073054c95b ("md/raid1: clean up read_balance.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pending"
commit 621739b00e16ca2d80411dc9b111cb15b91f3ba9 upstream.
This reverts commit 9a0e609e3fd8a95c96629b9fbde6b8c5b9a1456a.
(Resolved a conflict during revert due to commit bfebd1cdb4 that came
after)
This revert is motivated by a couple failure reports on request-based DM
multipath testbeds:
1) Netapp reported that their multipath fault injection test under heavy
IO load can stall longer than 300 seconds.
2) IBM reported elevated lock contention in their testbed (likely due to
increased back pressure due to IO not being dispatched as quickly):
https://www.redhat.com/archives/dm-devel/2015-July/msg00057.html
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e023612325a9034a542bfab79f78b1fe5ebb841 upstream.
Warning like this:
drivers/md/md.c: In function "update_array_info":
drivers/md/md.c:6394:26: warning: logical not is only applied
to the left hand side of comparison [-Wlogical-not-parentheses]
!mddev->persistent != info->not_persistent||
Fix it as Neil Brown said:
mddev->persistent != !info->not_persistent ||
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3b178adb3a3adf54ecf77758138b654c3ee7f09 upstream.
There is a bug that the bitmap superblock isn't initialised properly for
dm-raid, so a new field can have garbage in new fields.
(dm-raid does initialisation in the kernel - md initialised the
superblock in mdadm).
This means that for dm-raid we cannot currently trust the new ->nodes
field. So:
- use __GFP_ZERO to initialise the superblock properly for all new
arrays
- initialise all fields in bitmap_info in bitmap_new_disk_sb
- ignore ->nodes for dm arrays (yes, this is a hack)
This bug exposes dm-raid to bug in the (still experimental) md-cluster
code, so it is suitable for -stable. It does cause crashes.
References: https://bugzilla.kernel.org/show_bug.cgi?id=100491
Signed-off-By: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a8c0fa861e4db60409b4dda254cef5e17e4d43c upstream.
This error path retuns while still holding the lock - bad.
Fixes: 6791875e2e53 ("md: make reconfig_mutex optional for writes to md sysfs files.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd6919228d7e1867ae9e24ab27e3e4a366c87d21 upstream.
If ->private is set when ->run is called, it is assumed to be
a 'config' prepared as part of 'reshape'.
So it is important when we free that config, that we also clear ->private.
This is not often a problem as the mddev will normally be discarded
shortly after the config us freed.
However if an 'assemble' races with a final close, the assemble can use
the old mddev which has a stale ->private. This leads to any of
various sorts of crashes.
So clear ->private after calling ->free().
Reported-by: Nate Clark <nate@neworld.us>
Fixes: afa0f557cb15 ("md: rename ->stop to ->free")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c7518794a3647eb345d59ee52844e8a40405198 upstream.
Allocate memory using GFP_NOIO when deleting a btree. dm_btree_del()
can be called via an ioctl and we don't want to recurse into the FS or
block layer.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a822c83e47d97cdef38c4352e1ef62d9f46cfe98 upstream.
Given the pool's cell_sort_array holds 8192 pointers it triggers an
order 5 allocation via kmalloc. This order 5 allocation is prone to
failure as system memory gets more fragmented over time.
Fix this by allocating the cell_sort_array using vmalloc.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4c7e309340ff85072e96f529582d159002c36734 upstream.
redistribute3() shares entries out across 3 nodes. Some entries were
being moved the wrong way, breaking the ordering. This manifested as a
BUG() in dm-btree-remove.c:shift() when entries were removed from the
btree.
For additional context see:
https://www.redhat.com/archives/dm-devel/2015-May/msg00113.html
Signed-off-by: Dennis Yang <shinrairis@gmail.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6096d91af0b65a3967139b32d5adbb3647858a26 upstream.
The metadata space map has a simplified 'bootstrap' mode that is
operational when extending the space maps. Whilst in this mode it's
possible for some refcount decrement operations to become queued (eg, as
a result of shadowing one of the bitmap indexes). These decrements were
not being applied when switching out of bootstrap mode.
The effect of this bug was the leaking of a 4k metadata block. This is
detected by the latest version of thin_check as a non fatal error.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd4c1b7d0c95be1c9245118a3accc41a16f1db67 upstream.
If the number_of_areas argument was zero the kernel would crash on
div-by-zero. Add better input validation.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb4100ae7f312c3d614b37621c2b17b3b7cf65f8 upstream.
There is a race between a policy deciding to replace a cache entry,
the core target writing back any dirty data from this block, and other
IO threads doing IO to the same block.
This sort of problem is avoided most of the time by the core target
grabbing a bio prison cell before making the request to the policy.
But for a demotion the core target doesn't know which block will be
demoted, so can't do this in advance.
Fix this demotion race by introducing a callback to the policy interface
that allows the policy to grab the cell on behalf of the core target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MD_RECOVERY_DONE is normally cleared by md_check_recovery after a
resync etc finished. However it is possible for raid5_start_reshape
to race and start a reshape before MD_RECOVERY_DONE is cleared. This
can lean to multiple reshapes running at the same time, which isn't
good.
To make sure it is cleared before starting a reshape, and also clear
it when reaping a thread, just to be safe.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Checking ->sync_thread without holding the mddev_lock()
isn't really safe, even after flushing the workqueue which
ensures md_start_sync() has been run.
While this code is waiting for the lock, md_check_recovery could reap
the thread itself, and then start another thread (e.g. recovery might
finish, then reshape starts). When this thread gets the lock
md_start_sync() hasn't run so it doesn't get reaped, but
MD_RECOVERY_RUNNING gets cleared. This allows two threads to start
which leads to confusion.
So don't both if MD_RECOVERY_RUNNING isn't set, but if it is do
the flush and the test and the reap all under the mddev_lock to
avoid any race with md_check_recovery.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 6791875e2e53 ("md: make reconfig_mutex optional for writes to md sysfs files.")
Cc: stable@vger.kernel.org (v4.0+)
|
|
Returning zero from a 'store' function is bad.
The return value should be either len length of the string
or an error.
So use 'len' if 'err' is zero.
Fixes: 6791875e2e53 ("md: make reconfig_mutex optional for writes to md sysfs files.")
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel (v4.0+)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"Quite a few fixes for DM's blk-mq support thanks to extra DM multipath
testing from Junichi Nomura and Bart Van Assche.
Also fix a casting bug in dm_merge_bvec() that could cause only a
single page to be added to a bio (Joe identified this while testing
dm-cache writeback)"
* tag 'dm-4.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix casting bug in dm_merge_bvec()
dm: fix reload failure of 0 path multipath mapping on blk-mq devices
dm: fix false warning in free_rq_clone() for unmapped requests
dm: requeue from blk-mq dm_mq_queue_rq() using BLK_MQ_RQ_QUEUE_BUSY
dm mpath: fix leak of dm_mpath_io structure in blk-mq .queue_rq error path
dm: fix NULL pointer when clone_and_map_rq returns !DM_MAPIO_REMAPPED
dm: run queue on re-queue
|
|
dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn"). In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int. This code made
assumptions about the value of BIO_MAX_SECTORS.
A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors(). At
this point the cast from sector_t to int resulted in a zero value. The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.
This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.19+
|
|
dm-multipath accepts 0 path mapping.
# echo '0 2097152 multipath 0 0 0 0' | dmsetup create newdev
Such a mapping can be used to release underlying devices while still
holding requests in its queue until working paths come back.
However, once the multipath device is created over blk-mq devices,
it rejects reloading of 0 path mapping:
# echo '0 2097152 multipath 0 0 1 1 queue-length 0 1 1 /dev/sda 1' \
| dmsetup create mpath1
# echo '0 2097152 multipath 0 0 0 0' | dmsetup load mpath1
device-mapper: reload ioctl on mpath1 failed: Invalid argument
Command failed
With following kernel message:
device-mapper: ioctl: can't change device type after initial table load.
DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.
Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.
Fixes: 65803c205983 ("dm table: train hybrid target type detection to select blk-mq if appropriate")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Pull m,ore md bugfixes gfrom Neil Brown:
"Assorted fixes for new RAID5 stripe-batching functionality.
Unfortunately this functionality was merged a little prematurely. The
necessary testing and code review is now complete (or as complete as
it can be) and to code passes a variety of tests and looks quite
sensible.
Also a fix for some recent locking changes - a race was introduced
which causes a reshape request to sometimes fail. No data safety
issues"
* tag 'md/4.1-rc5-fixes' of git://neil.brown.name/md:
md: fix race when unfreezing sync_action
md/raid5: break stripe-batches when the array has failed.
md/raid5: call break_stripe_batch_list from handle_stripe_clean_event
md/raid5: be more selective about distributing flags across batch.
md/raid5: add handle_flags arg to break_stripe_batch_list.
md/raid5: duplicate some more handle_stripe_clean_event code in break_stripe_batch_list
md/raid5: remove condition test from check_break_stripe_batch_list.
md/raid5: Ensure a batch member is not handled prematurely.
md/raid5: close race between STRIPE_BIT_DELAY and batching.
md/raid5: ensure whole batch is delayed for all required bitmap updates.
|
|
When stacking request-based dm device on non blk-mq device and
device-mapper target could not map the request (error target is used,
multipath target with all paths down, etc), the WARN_ON_ONCE() in
free_rq_clone() will trigger when it shouldn't.
The warning was added by commit aa6df8d ("dm: fix free_rq_clone() NULL
pointer when requeueing unmapped request"). But free_rq_clone() with
clone->q == NULL is valid usage for the case where
dm_kill_unmapped_request() initiates request cleanup.
Fix this false warning by just removing the WARN_ON -- it only generated
false positives and was never useful in catching the intended case
(completing clone request not being mapped e.g. clone->q being NULL).
Fixes: aa6df8d ("dm: fix free_rq_clone() NULL pointer when requeueing unmapped request")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
A recent change removed the need for locking around writing
to "sync_action" (and various other places), but introduced a
subtle race.
When e.g. setting 'reshape' on a 'frozen' array, the 'frozen'
flag is cleared before 'reshape' is set, so the md thread can
get in and start trying recovery - which isn't wanted.
So instead of clearing MD_RECOVERY_FROZEN for any command
except 'frozen', only clear it when each specific command
is parsed. This allows the handling of 'reshape' to clear
the bit while a lock is held.
Also remove some places where we set MD_RECOVERY_NEEDED,
as it is always set on non-error exit of the function.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 6791875e2e53 ("md: make reconfig_mutex optional for writes to md sysfs files.")
|
|
Once the array has too much failure, we need to break
stripe-batches up so they can all be dealt with.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Now that the code in break_stripe_batch_list() is nearly identical
to the end of handle_stripe_clean_event, replace the later
with a function call.
The only remaining difference of any interest is the masking that is
applieds to dev[i].flags copied from head_sh.
R5_WriteError certainly isn't wanted as it is set per-stripe, not
per-patch. R5_Overlap isn't wanted as it is explicitly handled.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When a batch of stripes is broken up, we keep some of the flags
that were per-stripe, and copy other flags from the head to all
others.
This only happens while a stripe is being handled, so many of the
flags are irrelevant.
The "SYNC_FLAGS" (which I've renamed to make it clear there are
several) and STRIPE_DEGRADED are set per-stripe and so need to be
preserved. STRIPE_INSYNC is the only flag that is set on the head
that needs to be propagated to all others.
For safety, add a WARN_ON if others are set, except:
STRIPE_HANDLE - this is safe and per-stripe and we are going to set
in several cases anyway
STRIPE_INSYNC
STRIPE_IO_STARTED - this is just a hint and doesn't hurt.
STRIPE_ON_PLUG_LIST
STRIPE_ON_RELEASE_LIST - It is a point pointless for a batched
stripe to be on one of these lists, but it can happen
as can be safely ignored.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When we break a stripe_batch_list we sometimes want to set
STRIPE_HANDLE on the individual stripes, and sometimes not.
So pass a 'handle_flags' arg. If it is zero, always set STRIPE_HANDLE
(on non-head stripes). If not zero, only set it if any of the given
flags are present.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
break_stripe_batch_list
break_stripe_batch list didn't clear head_sh->batch_head.
This was probably a bug.
Also clear all R5_Overlap flags and if any were cleared, wake up
'wait_for_overlap'.
This isn't always necessary but the worst effect is a little
extra checking for code that is waiting on wait_for_overlap.
Also, don't use wake_up_nr() because that does the wrong thing
if 'nr' is zero, and it number of flags cleared doesn't
strongly correlate with the number of threads to wake.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
handle_stripe_clean_event() contains a chunk of code very
similar to check_break_stripe_batch_list().
If we make the latter more like the former, we can end up
with just one copy of this code.
This first step removed the condition (and the 'check_') part
of the name. This has the added advantage of making it clear
what check is being performed at the point where the function is
called.
Signed-off-by: NeilBrown <neilb@suse.de>
|
