| Age | Commit message (Collapse) | Author |
|---|
|
commit 0ba4581c84cfb39fd527f6b3457f1c97f6356c04 upstream.
The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8beb02343e7582980c6705816cd957cf4f74c7a upstream.
The tda1004x was updating the properties cache before locking.
If the device is not locked, the data at the registers are just
random values with no real meaning.
This caused the driver to fail with libdvbv5, as such library
calls GET_PROPERTY from time to time, in order to return the
DVB stats.
Tested with a saa7134 card 78:
ASUSTeK P7131 Dual, vendor PCI ID: 1043:4862
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4623e5967448444a4ea1e77beb58898c4af48693 upstream.
In the 3.17 kernel the poll() behavior changed for output streams:
as long as not all buffers were queued up poll() would return that
userspace can write. This is fine for the write() call, but when
using stream I/O this changed the behavior since the expectation
was that it would wait for buffers to become available for dequeuing.
This patch only enables the check whether you can queue buffers
for file I/O only, and skips it for stream I/O.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcc7fdbec53a960588f2c40232db2c6466c09917 upstream.
v4l2-compliance sends a zeroed struct v4l2_streamparm in
v4l2-test-formats.cpp::testParmType(), and this results in a division by
0 in some gspca subdrivers:
divide error: 0000 [#1] SMP
Modules linked in: gspca_ov534 gspca_main ...
CPU: 0 PID: 17201 Comm: v4l2-compliance Not tainted 4.3.0-rc2-ao2 #1
Hardware name: System manufacturer System Product Name/M2N-E SLI, BIOS
ASUS M2N-E SLI ACPI BIOS Revision 1301 09/16/2010
task: ffff8800818306c0 ti: ffff880095c4c000 task.ti: ffff880095c4c000
RIP: 0010:[<ffffffffa079bd62>] [<ffffffffa079bd62>] sd_set_streamparm+0x12/0x60 [gspca_ov534]
RSP: 0018:ffff880095c4fce8 EFLAGS: 00010296
RAX: 0000000000000000 RBX: ffff8800c9522000 RCX: ffffffffa077a140
RDX: 0000000000000000 RSI: ffff880095e0c100 RDI: ffff8800c9522000
RBP: ffff880095e0c100 R08: ffffffffa077a100 R09: 00000000000000cc
R10: ffff880067ec7740 R11: 0000000000000016 R12: ffffffffa07bb400
R13: 0000000000000000 R14: ffff880081b6a800 R15: 0000000000000000
FS: 00007fda0de78740(0000) GS:ffff88012fc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000014630f8 CR3: 00000000cf349000 CR4: 00000000000006f0
Stack:
ffffffffa07a6431 ffff8800c9522000 ffffffffa077656e 00000000c0cc5616
ffff8800c9522000 ffffffffa07a5e20 ffff880095e0c100 0000000000000000
ffff880067ec7740 ffffffffa077a140 ffff880067ec7740 0000000000000016
Call Trace:
[<ffffffffa07a6431>] ? v4l_s_parm+0x21/0x50 [videodev]
[<ffffffffa077656e>] ? vidioc_s_parm+0x4e/0x60 [gspca_main]
[<ffffffffa07a5e20>] ? __video_do_ioctl+0x280/0x2f0 [videodev]
[<ffffffffa07a5ba0>] ? video_ioctl2+0x20/0x20 [videodev]
[<ffffffffa07a59b9>] ? video_usercopy+0x319/0x4e0 [videodev]
[<ffffffff81182dc1>] ? page_add_new_anon_rmap+0x71/0xa0
[<ffffffff811afb92>] ? mem_cgroup_commit_charge+0x52/0x90
[<ffffffff81179b18>] ? handle_mm_fault+0xc18/0x1680
[<ffffffffa07a15cc>] ? v4l2_ioctl+0xac/0xd0 [videodev]
[<ffffffff811c846f>] ? do_vfs_ioctl+0x28f/0x480
[<ffffffff811c86d4>] ? SyS_ioctl+0x74/0x80
[<ffffffff8154a8b6>] ? entry_SYSCALL_64_fastpath+0x16/0x75
Code: c7 93 d9 79 a0 5b 5d e9 f1 f3 9a e0 0f 1f 00 66 2e 0f 1f 84 00
00 00 00 00 66 66 66 66 90 53 31 d2 48 89 fb 48 83 ec 08 8b 46 10 <f7>
76 0c 80 bf ac 0c 00 00 00 88 87 4e 0e 00 00 74 09 80 bf 4f
RIP [<ffffffffa079bd62>] sd_set_streamparm+0x12/0x60 [gspca_ov534]
RSP <ffff880095c4fce8>
---[ end trace 279710c2c6c72080 ]---
Following what the doc says about a zeroed timeperframe (see
http://www.linuxtv.org/downloads/v4l-dvb-apis/vidioc-g-parm.html):
...
To reset manually applications can just set this field to zero.
fix the issue by resetting the frame rate to a default value in case of
an unusable timeperframe.
The fix is done in the subdrivers instead of gspca.c because only the
subdrivers have notion of a default frame rate to reset the camera to.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2cc2f0b35465951eaaf0387fd55e29835ed7ea6 upstream.
A previous patch added a check if the firmware is too big, but it didn't
set the return error code with the right value.
[mchehab@osg.samsung.com: I ended by applying a v1 of Laura's patch, without
the proper return code. This patch contains the difference between v2 and v1 of
the Laura's "si2157: Bounds check firmware" patch]
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
commit c9d57de6103e343f2d4e04ea8d9e417e10a24da7 upstream.
When in FE_TUNE_MODE_ONESHOT the frontend must report
the actual capabilities so user can take appropriate
action.
With frontends that can't do auto inversion this is done
by dvb-core automatically so CAN_INVERSION_AUTO is valid.
However, when in FE_TUNE_MODE_ONESHOT this is not true.
So only set FE_CAN_INVERSION_AUTO in modes other than
FE_TUNE_MODE_ONESHOT
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 768acf46e1320d6c41ed1b7c4952bab41c1cde79 upstream.
The driver allocates the spinlock but fails to initialize it correctly.
The kernel reports a BUG indicating bad spinlock magic when spinlock
debugging is enabled.
Call spin_lock_init() on it to initialize it correctly.
Fixes: b4e3e59fb59c ("[media] rc: add sunxi-ir driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac75fe5d8fe4a0bf063be18fb29684405279e79e upstream.
That prevents this bug:
[ 2382.269496] BUG: unable to handle kernel NULL pointer dereference at 0000000000000540
[ 2382.270013] IP: [<ffffffffa01fe616>] snd_card_free+0x36/0x70 [snd]
[ 2382.270013] PGD 0
[ 2382.270013] Oops: 0002 [#1] SMP
[ 2382.270013] Modules linked in: saa7134_alsa(-) tda1004x saa7134_dvb videobuf2_dvb dvb_core tda827x tda8290 tuner saa7134 tveeprom videobuf2_dma_sg videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc tun bridge stp llc ebtables ip6table_filter ip6_tables nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack it87 hwmon_vid snd_hda_codec_idt snd_hda_codec_generic iTCO_wdt iTCO_vendor_support snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_seq pcspkr i2c_i801 snd_seq_device snd_pcm snd_timer lpc_ich snd mfd_core soundcore binfmt_misc i915 video i2c_algo_bit drm_kms_helper drm r8169 ata_generic serio_raw pata_acpi mii i2c_core [last unloaded: videobuf2_memops]
[ 2382.270013] CPU: 0 PID: 4899 Comm: rmmod Not tainted 4.5.0-rc1+ #4
[ 2382.270013] Hardware name: PCCHIPS P17G/P17G, BIOS 080012 05/14/2008
[ 2382.270013] task: ffff880039c38000 ti: ffff88003c764000 task.ti: ffff88003c764000
[ 2382.270013] RIP: 0010:[<ffffffffa01fe616>] [<ffffffffa01fe616>] snd_card_free+0x36/0x70 [snd]
[ 2382.270013] RSP: 0018:ffff88003c767ea0 EFLAGS: 00010286
[ 2382.270013] RAX: ffff88003c767eb8 RBX: 0000000000000000 RCX: 0000000000006260
[ 2382.270013] RDX: ffffffffa020a060 RSI: ffffffffa0206de1 RDI: ffff88003c767eb0
[ 2382.270013] RBP: ffff88003c767ed8 R08: 0000000000019960 R09: ffffffff811a5412
[ 2382.270013] R10: ffffea0000d7c200 R11: 0000000000000000 R12: ffff88003c767ea8
[ 2382.270013] R13: 00007ffe760617f7 R14: 0000000000000000 R15: 0000557625d7f1e0
[ 2382.270013] FS: 00007f80bb1c0700(0000) GS:ffff88003f400000(0000) knlGS:0000000000000000
[ 2382.270013] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 2382.270013] CR2: 0000000000000540 CR3: 000000003c00f000 CR4: 00000000000006f0
[ 2382.270013] Stack:
[ 2382.270013] 000000003c767ed8 ffffffff00000000 ffff880000000000 ffff88003c767eb8
[ 2382.270013] ffff88003c767eb8 ffffffffa049a890 00007ffe76060060 ffff88003c767ef0
[ 2382.270013] ffffffffa049889d ffffffffa049a500 ffff88003c767f48 ffffffff8111079c
[ 2382.270013] Call Trace:
[ 2382.270013] [<ffffffffa049889d>] saa7134_alsa_exit+0x1d/0x780 [saa7134_alsa]
[ 2382.270013] [<ffffffff8111079c>] SyS_delete_module+0x19c/0x1f0
[ 2382.270013] [<ffffffff8170fc2e>] entry_SYSCALL_64_fastpath+0x12/0x71
[ 2382.270013] Code: 20 a0 48 c7 c6 e1 6d 20 a0 48 89 e5 41 54 53 4c 8d 65 d0 48 89 fb 48 83 ec 28 c7 45 d0 00 00 00 00 49 8d 7c 24 08 e8 7a 55 ed e0 <4c> 89 a3 40 05 00 00 48 89 df e8 eb fd ff ff 85 c0 75 1a 48 8d
[ 2382.270013] RIP [<ffffffffa01fe616>] snd_card_free+0x36/0x70 [snd]
[ 2382.270013] RSP <ffff88003c767ea0>
[ 2382.270013] CR2: 0000000000000540
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 329d88da4df9a96da43018aceabd3a06e6a7e7ae upstream.
This is a partial revert of commit ed8d1cf07cb16d ("[media] Export I2C
module alias information in missing drivers") that exported the module
aliases for the I2C drivers that were missing to make autoload to work.
But there is a bug report [0] that auto load of the ir-kbd-i2c driver
cause the Hauppauge HD-PVR driver to not behave correctly.
This is a hdpvr latent bug that was just exposed by ir-kbd-i2c module
autoloading working and will also happen if the I2C driver is built-in
or a user calls modprobe to load the module and register the driver.
But there is a regression experimented by users so until the real bug
is fixed, let's not export the module alias for the ir-kbd-i2c driver
even when this just masks the actual issue.
[0]: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=810726
Fixes: ed8d1cf07cb1 ("[media] Export I2C module alias information in missing drivers")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab.
* tag 'media/v4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] airspy: increase USB control message buffer size
[media] hackrf: move RF gain ctrl enable behind module parameter
[media] hackrf: fix possible null ptr on debug printing
[media] Revert "[media] ivtv: avoid going past input/audio array"
|
|
Driver requested device firmware version string during probe using
only 24 byte long buffer. That buffer is too small for newer firmware
versions, which causes device firmware hang - device stops responding
to any commands after that. Increase buffer size to 128 which should
be enough for any current and future version strings.
Link: https://github.com/airspy/host/issues/27
Cc: <stable@vger.kernel.org> # 3.17+
Reported-by: Benjamin Vernoux <bvernoux@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Used Avago MGA-81563 RF amplifier could be destroyed pretty easily
with too strong signal or transmitting to bad antenna.
Add module parameter 'enable_rf_gain_ctrl' which allows enabling
RF gain control - otherwise, default without the module parameter,
RF gain control is set to 'grabbed' state which prevents setting
value to the control.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
drivers/media/usb/hackrf/hackrf.c:1533 hackrf_probe()
error: we previously assumed 'dev' could be null (see line 1366)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch broke ivtv logic, as reported at
https://bugzilla.redhat.com/show_bug.cgi?id=1278942
This reverts commit 09290cc885937cab3b2d60a6d48fe3d2d3e04061.
Cc: stable@vger.kernel.org # for v4.1 and upper
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
pci_set_dma_mask returns a negative errno value, not a bool like
pci_dma_supported. This of course was just a giant test for attention :)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jongman Heo <jongman.heo@samsung.com>
Tested-by: Jongman Heo <jongman.heo@samsung.com> [pcnet32]
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Sergey Kozlov <serjk@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sleep and avoiding waking kswapd
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
|
|
'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next
|
|
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.
Fixes: 478932b16052f5ded74685d096ae920cd17d6424
Cc: <stable@kernel.org> # 4.2+
Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add lock to prevent concurrent access for control message as control
message function uses shared buffer. Without the lock there may be
remote control polling which messes the buffer causing IO errors.
Increase buffer size and add check for maximum supported message
length.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=103391
Fixes: c56222a6b25c ("[media] rtl28xxu: move usb buffers to state")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Antti Palosaari <crope@iki.fi>
|
|
Fixes the following randconfig problem:
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x12204f): undefined reference to `v4l2_async_unregister_subdev'
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x122057): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_close':
v4l2-flash-led-class.c:(.text+0x12208f): undefined reference to `v4l2_fh_is_singular'
v4l2-flash-led-class.c:(.text+0x1220c8): undefined reference to `__v4l2_ctrl_s_ctrl'
drivers/built-in.o: In function `v4l2_flash_open':
v4l2-flash-led-class.c:(.text+0x12227f): undefined reference to `v4l2_fh_is_singular'
drivers/built-in.o: In function `v4l2_flash_init_controls':
v4l2-flash-led-class.c:(.text+0x12274e): undefined reference to `v4l2_ctrl_handler_init_class'
v4l2-flash-led-class.c:(.text+0x122797): undefined reference to `v4l2_ctrl_new_std_menu'
v4l2-flash-led-class.c:(.text+0x1227e0): undefined reference to `v4l2_ctrl_new_std'
v4l2-flash-led-class.c:(.text+0x122826): undefined reference to `v4l2_ctrl_handler_setup'
v4l2-flash-led-class.c:(.text+0x122839): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x1228e2): undefined reference to `v4l2_subdev_init'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x12293b): undefined reference to `v4l2_async_register_subdev'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x122949): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o:(.rodata+0x20ef8): undefined reference to `v4l2_subdev_queryctrl'
drivers/built-in.o:(.rodata+0x20f10): undefined reference to `v4l2_subdev_querymenu'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
|
|
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:
si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa085708f
Add the proper check.
Cc: stable@kernel.org
Reported-by: Stuart Auchterlonie <sauchter@redhat.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
When reading the firmware and sending commands, the length
must be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the
expected format. Add the proper check.
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The variable err was never initialized, that means we had been checking
a garbage value in the for loop. Moreover if the segment is not outside
the firmware file then also we have been returning the garbage.
Initialize it to 0 so that on success we return the value and no need to
check in the for loop also as it is initially 0 and whenever that value
changes we have done a break from the loop.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
static analysis with cppcheck detected the following error:
[drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:1210]:
(error) Uninitialized variable: ret
ret is never initialised, so garbage is being returned. Instead
return the error return from the call of request_firmware_nowait
Signed-off-by: Colin Ian King <colin.king@canonical.com>
|
|
If CONFIG_DVB_LNBH25 is disabled, a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function return type was wrong which caused a build error.
Fixes: e025273b86fb ("[media] lnbh25: LNBH25 SEC controller driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
If CONFIG_DVB_HORUS3A is disabled a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function parameters were wrong which caused a build error.
Fixes: a5d32b358254f ("[media] horus3a: Sony Horus3A DVB-S/S2 tuner driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
c8sectpfe driver selects CONFIG_FW_LOADER_USER_HELPER_FALLBACK by some
reason, but this option is known to be harmful, leading to minutes of
stalls at boot time. The option was intended for only compatibility
for an old exotic system that mandates the udev interaction, and not a
thing a driver selects by itself. Let's remove it.
Fixes: 850a3f7d5911 ('[media] c8sectpfe: Add Kconfig and Makefile for the driver')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Convert ivtv_yuv_prep_user_dma() to use get_user_pages_unlocked() so
that we don't unnecessarily leak knowledge about mm locking into drivers
code.
CC: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Since commit 5d0360a4f027576e5419d4a7c711c9ca0f1be8ca it's not possible
anymore to set auto clusters from auto to manual using VIDIOC_S_CTRL.
For example, setting autogain to manual with gspca/ov534 driver and this
sequence of commands does not work:
v4l2-ctl --set-ctrl=gain_automatic=1
v4l2-ctl --list-ctrls | grep gain_automatic
# The following does not work
v4l2-ctl --set-ctrl=gain_automatic=0
v4l2-ctl --list-ctrls | grep gain_automatic
Changing the value using VIDIOC_S_EXT_CTRLS (like qv4l2 does) works
fine.
The apparent cause by looking at the changes in 5d0360a and comparing
with the code path for VIDIOC_S_EXT_CTRLS seems to be that the code in
v4l2-ctrls.c::set_ctrl() is not calling user_to_new() anymore after
calling update_from_auto_cluster(master).
However the root cause of the problem is that calling
update_from_auto_cluster(master) overrides also the _master_ control
state calling cur_to_new() while it was supposed to only update the
volatile controls.
Calling user_to_new() after update_from_auto_cluster(master) was just
masking the original bug by restoring the correct new value of the
master control before making the changes permanent.
Fix the original bug by making update_from_auto_cluster() not override
the new master control value.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: <stable@vger.kernel.org> # for v3.17 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Format names are set by core nowadays. Remove name from driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
HackRF SDR device has both receiver and transmitter. There is limitation
that receiver and transmitter cannot be used at the same time
(half-duplex operation). That patch implements transmitter support to
existing receiver only driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
[hans.verkuil@cisco.com: fix krobot unused variable warning]
[hans.verkuil@cisco.com: add back s_modulator from PATCHv4]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Implement single funtion, hackrf_set_params(), which handles all
needed settings. Controls and other IOCTLs are just wrappers to that
function. That way we can get easily better control what we could do
on different device states - sleeping, receiving, transmitting.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
There is Avago MGA-81563 amplifier just right after antenna connector.
It could be turned on/off and its gain is around 12dB.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add type field to that struct like it counterpart v4l2_tuner
already has. We need type field to distinguish different tuner
types from each others for transmitter too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
New IOCTL ops:
vidioc_enum_fmt_sdr_out
vidioc_g_fmt_sdr_out
vidioc_s_fmt_sdr_out
vidioc_try_fmt_sdr_out
New vb2 buffertype:
V4L2_BUF_TYPE_SDR_OUTPUT
New v4l2 capability:
V4L2_CAP_SDR_OUTPUT
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add new RF tuner gain control named RF Gain. That is aimed for first
amplifier chip right after antenna connector.
There is existing LNA Gain control, which is quite same, but it is
aimed for cases amplifier is integrated to tuner chip. Some designs
have both, as almost all recent tuner silicons has integrated LNA/RF
amplifier in any case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
SDR receiver has ADC (Analog-to-Digital Converter) and SDR transmitter
has DAC (Digital-to-Analog Converter). Originally I though it could
be good idea to have own type for receiver and transmitter, but now I
feel one common type for SDR is enough. So lets rename it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: this was added in 4.4, so update 4.2 to 4.4]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
