summaryrefslogtreecommitdiff
path: root/drivers/mtd
AgeCommit message (Collapse)Author
2012-10-11ENGR00181390-2: qspi: Add Quad SPI driver support for VybridAlison Wang
Add Quad SPI driver support for Vybrid. Signed-off-by: Alison Wang <b18965@freescale.com> Xiaochun Li <b41219@freescale.com>
2012-08-10ENGR00181374-2: nfc: add NFC driver support for FaradayAlison Wang
Add NFC driver support for Faraday. Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2012-02-08ENGR00173947-1 mtd/gpmi : add BBT support to gpmi nand driverHuang Shijie
Add a new field to gpmi_nand_platform_data{}. Make the BBT support to board specific. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-02-07ENGR00173731-7 MX6Q/GPMI : add gpmi for mx6qHuang Shijie
add gpmi support to mx6q for the imx_3.0.15. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-02-07ENGR00173731-3 mxs-dma : rewrite the last parameter of mxs_dma_prep_slave_sg()Huang Shijie
[1] Background : The GPMI does ECC read page operation with a DMA chain consist of three DMA Command Structures. The middle one of the chain is used to enable the BCH, and read out the NAND page. The WAIT4END(wait for command end) is a comunication signal between the GPMI and MXS-DMA. [2] The current DMA code sets the WAIT4END bit at the last one, such as: +-----+ +-----+ +-----+ | cmd | ------------> | cmd | ------------------> | cmd | +-----+ +-----+ +-----+ ^ | | set WAIT4END here This chain works fine in the mx23/mx28. [3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should be set not only at the last DMA Command Structure, but also at the middle one, such as: +-----+ +-----+ +-----+ | cmd | ------------> | cmd | ------------------> | cmd | +-----+ +-----+ +-----+ ^ ^ | | | | set WAIT4END here too set WAIT4END here If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state. In the next ECC write page operation, a DMA-timeout occurs. This has been catched in the MX6Q board. [4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(), and use the dma_ctrl_flags: --------------------------------------------------------- DMA_PREP_INTERRUPT : append a new DMA Command Structrue. DMA_CTRL_ACK : set the WAIT4END bit for this DMA Command Structure. --------------------------------------------------------- [5] changes to the relative drivers: For gpmi-nand driver: use the new flags. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-02-07ENGR00173731-2 mxs-dma : use the new mxs-dma.hHuang Shijie
use the new header : mxs-dma.h. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-31mtd: abstract last MTD partition parser argumentDmitry Eremin-Solenikov
Encapsulate last MTD partition parser argument into a separate structure. Currently it holds only 'origin' field for RedBoot parser, but will be extended in future to contain at least device_node for OF devices. Amended commentary to make kerneldoc happy Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2012-01-31mtd: add new API for handling MTD registrationDmitry Eremin-Solenikov
Lots (nearly all) mtd drivers contain nearly the similar code that calls parse_mtd_partitions, provides some platform-default values, if parsing fails, and registers mtd device. This is an aim to provide single implementation of this scenario: mtd_device_parse_register() which will handle all this parsing and defaults. Artem: amended comments Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2012-01-31net: remove mm.h inclusion from netdevice.hAlexey Dobriyan
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually). To prevent mm.h inclusion via other channels also extract "enum dma_data_direction" definition into separate header. This tiny piece is what gluing netdevice.h with mm.h via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h". Removal of mm.h from scatterlist.h was tried and was found not feasible on most archs, so the link was cutoff earlier. Hope people are OK with tiny include file. Note, that mm_types.h is still dragged in, but it is a separate story. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-31mtd: gpmi-lib: convert to clk_prepare/clk_unprepareShawn Guo
The patch converts gpmi nand driver to clk_prepare/clk_unprepare by using helper functions clk_prepare_enable/clk_disable_unprepare. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: Huang Shijie <b32955@freescale.com> Cc: Artem Bityutskiy <artem.bityutskiy@intel.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-01-31mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23Huang Shijie
In MX28, if we do not reset the BCH module. The BCH module may becomes unstable when the board reboots for several thousands times. This bug has been catched in customer's production. The patch adds some comments(some from Wolfram Sang), and fixes it now. Also change gpmi_reset_block() to static. Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-01-31mtd: gpmi-nand: move to dma_transfer_directionShawn Guo
This patch fixes usage of dma direction to adopt dma_transfer_direction. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-01-31mtd: gpmi: add missing include 'module.h'Wolfram Sang
Fixes: drivers/mtd/nand/gpmi-nand/gpmi-nand.c: In function 'gpmi_nfc_init': drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: error: 'THIS_MODULE' undeclared (first use in this function) drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: note: each undeclared identifier is reported only once for each function it appears in drivers/mtd/nand/gpmi-nand/gpmi-nand.c: At top level: drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:15: error: expected declaration specifiers or '...' before string constant drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: data definition has no type or storage class drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR' and some more... Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-30mtd: add the common code for GPMI-NAND controller driverHuang Shijie
These files contain the common code for the GPMI-NAND driver. Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Koen Beel <koen.beel@barco.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2012-01-30mtd: add GPMI-NAND driver in the config and MakefileHuang Shijie
add the GPMI-NAND driver in the relevant Kconfig and Makefile in the MTD. Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Koen Beel <koen.beel@barco.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2012-01-30mtd: add helper functions library and header files for GPMI NAND driverHuang Shijie
bch-regs.h : registers file for BCH module gpmi-regs.h: registers file for GPMI module gpmi-lib.c: helper functions library. Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Koen Beel <koen.beel@barco.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2012-01-19ENGR00172281 GPMI : fix the wrong flag for send_page()Huang Shijie
There is only one DMA command in the chain, So MXS_DMA_F_APPEND is not needed. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-19ENGR00169906-5 GPMI : change the code for new interfaceHuang Shijie
If we do not set the WAIT4END in the middle DMA command structure of the long DMA command chain, a DMA timeout may occurs. The reason of the DMA timeout is: [1] We do not set the WAIT4END in the DMA command structure which do the ECC READ PAGE by the BCH. [2] So the following DMA command structure (maybe in other DMA CHAIN)may disable the BCH module. [3] If the time delay between [2] and [1] is long enough, it's ok. But if the time delay is not long enough, the BCH module may become unnormal, so it can not finish its job. The DMA will timeout in this case. We have changed the DMA interface to fix the bug, now use the new interface. Acked-by: Jason Liu <r64343@freescale.com> Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-19ENGR00169906-2 GPMI : setup the TIMING1 for ready/busyHuang Shijie
The TIMING1 specifies the timeouts used when monitoring the NAND READY pin and IOWAIT signals. We should set a default value for it. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00162181-2 GPMI : select the MXS-DMA and MTD_CHARHuang Shijie
select the MXS-DMA and MTD_CHAR macros. The gpmi driver needs them to be enabled. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00162181-1 MX6Q/GPMI : init the GPMI blockHuang Shijie
The GPMI block SHOULD be initialized when the system starts. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00160936 GPMI : disable the DDR codeHuang Shijie
We do not support any ONFI or TOGGLE nand now. So disable the DDR code. If keep it enabled, the ECC chunk will be 1K for ONFI nand, this is not compatible with the kobs-ng which uses 512bytes for ECC chunk size. So disable it now. change it in future. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00139247-3 MTD : add GPMI driver for IMX6QHuang Shijie
add the gpmi driver for imx6q. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00143186 GPMI : add the kernel command parameter to disable/enable gpmiHuang Shijie
add the kernel command parameter to control whether we should enable the GPMI NAND driver. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00141558-9 MTD : add gpmi support for MX50Huang Shijie
add the gpmi support for mx50. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00141558-6 MTD : add GPMI driver in the config and MakefileHuang Shijie
add the GPMI driver in the relevant Kconfig and Makefile in the MTD. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00141558-5 MTD : add support for imx23 and imx28Huang Shijie
Add the implementation code for imx23 and imx28. The imx23 and imx28 share most of the same code. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09ENGR00141558-4 MTD : add the common code for GPMI controller driverHuang Shijie
These files contain the common code for the GPMI driver. Signed-off-by: Huang Shijie <b32955@freescale.com>
2012-01-09nand: add more nand devicesRob Herring
Signed-off-by: Rob Herring <r.herring@freescale.com>
2012-01-09nand: export symbols needed for stmp3xxx nand nand: increase max nand page ↵Rob Herring
and oob sizes Signed-off-by: Rob Herring <r.herring@freescale.com>
2011-11-11mtd: nand_base: always initialise oob_poi before writing OOB dataTHOMSON, Adam (Adam)
commit f722013ee9fd24623df31dec9a91a6d02c3e2f2f upstream. In nand_do_write_ops() code it is possible for a caller to provide ops.oobbuf populated and ops.mode == MTD_OOB_AUTO, which currently means that the chip->oob_poi buffer isn't initialised to all 0xFF. The nand_fill_oob() method then carries out the task of copying the provided OOB data to oob_poi, but with MTD_OOB_AUTO it skips areas marked as unavailable by the layout struct, including the bad block marker bytes. An example of this causing issues is when the last OOB data read was from the start of a bad block where the markers are not 0xFF, and the caller wishes to write new OOB data at the beginning of another block. In this scenario the caller would provide OOB data, but nand_fill_oob() would skip the bad block marker bytes in oob_poi before copying the OOB data provided by the caller. This means that when the OOB data is written back to NAND, the block is inadvertently marked as bad without the caller knowing. This has been witnessed when using YAFFS2 where tags are stored in the OOB. To avoid this oob_poi is always initialised to 0xFF to make sure no left over data is inadvertently written back to the OOB area. Credits to Brian Norris <computersforpeace@gmail.com> for fixing this patch. Signed-off-by: Adam Thomson <adam.thomson@alcatel-lucent.com> Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-11mtd: pxa3xx_nand: Fix blank page ECC mismatchDaniel Mack
commit 543e32d5ff165d0d68deedb0e3557478c7c36a4a upstream. This bug was introduced in f8155a40 ("mtd: pxa3xx_nand: rework irq logic") and causes the PXA3xx NAND controller fail to operate with NAND flash that has empty pages. According to the comment in this block, the hardware controller will report a double-bit error for empty pages, which can and must be ignored. This patch restores the original behaviour of the driver. Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Lei Wen <leiwen@marvell.com> Cc: Haojian Zhuang <haojian.zhuang@marvell.com> Cc: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-11mtd: pxa3xx_nand: fix nand detection issueLei Wen
commit 0fab028b77d714ad302404b23306cf7adb885223 upstream. When keep_config is set, the detection would goes different routine. That the driver would read out the setting which is set previously by bootloader. While most bootloader keep the irq mask as off, and current driver need all irq default open, keep_config behavior would lead to no irq at all. Signed-off-by: Lei Wen <leiwen@marvell.com> Tested-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-11mtd: provide an alias for the redboot module nameAndres Salomon
commit d5de1907d0af22e1a02de2b16a624148517a39c2 upstream. parse_mtd_partitions takes a list of partition types; if the driver isn't loaded, it attempts to load it, and then it grabs the partition parser. For redboot, the module name is "redboot.ko", while the parser name is "RedBoot". Since modprobe is case-sensitive, attempting to modprobe "RedBoot" will never work. I suspect the embedded systems that make use of redboot just always manually loaded redboot prior to loading their specific nand chip drivers (or statically compiled it in). Signed-off-by: Andres Salomon <dilinger@queued.net> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-11mtd: mtdchar: add missing initializer on raw writePeter Wippich
commit bf5140817b2d65faac9b32fc9057a097044ac35b upstream. On writes in MODE_RAW the mtd_oob_ops struct is not sufficiently initialized which may cause nandwrite to fail. With this patch it is possible to write raw nand/oob data without additional ECC (either for testing or when some sectors need different oob layout e.g. bootloader) like nandwrite -n -r -o /dev/mtd0 <myfile> Signed-off-by: Peter Wippich <pewi@gw-instruments.de> Tested-by: Ricard Wanderlof <ricardw@axis.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-06-22powerpc/85xx: fix NAND_CMD_READID read bytes numberShaohui Xie
when nand_get_flash_type() is called, it will read 8 bytes of ID instead of 5, but the driver only read 5 bytes, so kernel will dump error messages like: fsl-lbc ffe124000.localbus: read_byte beyond end of buffer fsl-lbc ffe124000.localbus: read_byte beyond end of buffer fsl-lbc ffe124000.localbus: read_byte beyond end of buffer Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-05-27Merge git://git.infradead.org/mtd-2.6Linus Torvalds
* git://git.infradead.org/mtd-2.6: (97 commits) mtd: kill CONFIG_MTD_PARTITIONS mtd: remove add_mtd_partitions, add_mtd_device and friends mtd: convert remaining users to mtd_device_register() mtd: samsung onenand: convert to mtd_device_register() mtd: omap2 onenand: convert to mtd_device_register() mtd: txx9ndfmc: convert to mtd_device_register() mtd: tmio_nand: convert to mtd_device_register() mtd: socrates_nand: convert to mtd_device_register() mtd: sharpsl: convert to mtd_device_register() mtd: s3c2410 nand: convert to mtd_device_register() mtd: ppchameleonevb: convert to mtd_device_register() mtd: orion_nand: convert to mtd_device_register() mtd: omap2: convert to mtd_device_register() mtd: nomadik_nand: convert to mtd_device_register() mtd: ndfc: convert to mtd_device_register() mtd: mxc_nand: convert to mtd_device_register() mtd: mpc5121_nfc: convert to mtd_device_register() mtd: jz4740_nand: convert to mtd_device_register() mtd: h1910: convert to mtd_device_register() mtd: fsmc_nand: convert to mtd_device_register() ... Fixed up trivial conflicts in - drivers/mtd/maps/integrator-flash.c: removed in ARM tree - drivers/mtd/maps/physmap.c: addition of afs partition probe type clashing with removal of CONFIG_MTD_PARTITIONS
2011-05-26mtd: Use platform_data to retrieve tmio_nand platform bitsSamuel Ortiz
With the addition of the platform device mfd_cell pointer, we can now cleanly pass the sub device drivers platform data pointers through the regular device platform_data one, and get rid of mfd_get_data(). Cc: Ian Molton <spyro@f2s.com> Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-05-25mtd: kill CONFIG_MTD_PARTITIONSJamie Iles
Now that none of the drivers use CONFIG_MTD_PARTITIONS we can remove it from Kconfig and the last remaining uses. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: remove add_mtd_partitions, add_mtd_device and friendsJamie Iles
These symbols are replaced with mtd_device_register() (and removal with mtd_device_unregister()) for public registration. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: convert remaining users to mtd_device_register()Jamie Iles
The older add_mtd_device()/add_mtd_partitions() and their removal counterparts will soon be gone. Replace uses with mtd_device_register() and mtd_device_unregister(). Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: samsung onenand: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: omap2 onenand: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: txx9ndfmc: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: tmio_nand: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: socrates_nand: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: sharpsl: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: s3c2410 nand: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: ppchameleonevb: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25mtd: orion_nand: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
generated by cgit v1.2.3 (git 2.0.4) at 2025-09-16 11:10:51 +0000