| Age | Commit message (Collapse) | Author |
|---|
|
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change limits the PF/VF driver to 9.5K max jumbo frame size in order
prevent a possible Tx hang in the adapter when sending frames between
pools.
All of the parts in ixgbe support a maximum frame of 15.5K for standard
traffic, however with SR-IOV or DCB enabled they should be limiting the
MTU size to 9.5K. Instead of adding extra checks which would have to
change the MTU when we go into or out of these modes it is preferred to
just use a standard 9.5K MTU limit for all modes so that this extra
overhead can be avoided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds device support for Ethernet Controller X540-AT1.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The loop in ixgbe_reinit_fdir_tables_82599() only polls for up to 100us
resulting in failures to update the FDIR filter table at 1Gbps and 10Gbps
when under load.
The poll times for FDIRCTRL.INIT_DONE are 55us, 550us and 5.5ms for 10Gbps,
1Gbps and 100Mbps respectively.
This patch sets the wait time to be the same as in ixgbe_fdir_enable_82599()
Reported-by: Bhushan <shashi-sm@users.sf.net>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes a development issue that occurred due to invalid modes reported
in the ethtool get_ts_info function. The issue is resolved by removing
unsupported modes from the Rx supported list.
CC: stable <stable@vger.kernel.org> [3.5]
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Driver was enabling PPS interrupt even when user wasn't enabling it via the
ptp core. This patch fixes the PPS so that it is only enabled explicitly, and
moves the interrupt enabling code into the correct location in the driver
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes a bug in the method used for calculating the trigger
alignment for SDP0 when enabling a PPS output on the X540. The alignment math
wasn't properly taking into account the overflow cyclecounter, and was
misaligning the pin triggers so that two X540 devices synced properly had
mis-aligned SDP pins. This patch fixes the math to calculate the correct
seconds alignment for the PPS signal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
|
|
Later changes need to be able to refer to neighbour attributes
when doing fdb_add.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The counter is not valid unless the controller is running in IOV mode.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal functions for add/deleting addresses don't change
their argument.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Noticed that the byte and packet count statistics are under-
counting traffic handled by the DDP offload when there is more
than one DDP completion processed in a single call to
ixgbe_clean_rx_irq. This patch fixes that.
I tried to optimize the setting of the rss value so that it
only would have to be computed once, and only when there is
a DDP completion present.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Added the reg_ops file to debugfs with commands to read and write
a register to give users the ability to read and write individual
registers on the fly.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Added the netdev_ops file to debugfs with a command to call the
ndo_tx_timeout function to give users the ability to simulate a
tx_timeout call made by the kernel.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds debugfs support to the ixgbe driver to give
users the ability to access kernel information and to
simulate kernel events.
The filesystem is set up in the following driver/PCI-instance
hierarchy:
<debugfs>
|-- ixgbe
|-- PCI instance
| |-- attribute files
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use %u instead of %d to display u32 variable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change fixes the assumptions of the rate limiting code that previously
assumed that each VF would only ever have 2 queues. This update makes it
so that we now use a queues per pool value that is determined based on the
VMDq feature mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-By: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The PF was not correctly registering any of its VLANs. As a result any
VLAN tagged traffic from the VF would not be delivered to the PF because
the VLAN was never assigned to the PF pool.
In addition the VF was not allowed to receive traffic from VLAN 0 if it was
allowed to receive untagged frames. This change corrects that so that it
will correctly receive traffic from VLAN 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
|
|
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove a for loop that does nothing in ixgbe_probe().
This is a remnant from when we had IO bars (compare to the ixgb code).
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Introduce an inline function pci_pcie_type(dev) to extract PCIe
device type from pci_dev->pcie_flags_reg field, and prepare for
removing pci_dev->pcie_type.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
|
|
This change updates the code related to configuring the transmit frame
checksum. Specifically I have updated the code so that we can only skip
inserting the checksum in the case that we are not performing some other
offload that will modify the frame data.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This change moves the RSC code into the non-EOP descriptor handling
function. The main motivation behind this change is to help reduce the
overhead in the non-RSC case. Previously the non-RSC path code would
always be checking for append count even if RSC had been disabled. Now
this code is completely skipped in a single conditional check instead of
having to make two separate checks.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This patch creates a function named ixgbe_fetch_rx_buffer. The sole
purpose of this function is to retrieve a single buffer off of the ring and
to place it in an skb.
The advantage to doing this is that it helps improve the readability since
I can decrease the indentation and for the code in this section.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This change makes it so that if only the first 256 bytes of a buffer are
used we just copy the data out and leave the offset and page count
unchanged. There are multiple advantages to this. First it allows us to
reuse the page much more in the case of pages larger than 4K. It also
allows us to avoid some expensive atomic operations in the form of
get_page/put_page. In perf I have seen CPU utilization for put_page drop
from 3.5% to 1.8% as a result of this patch when doing small packet routing,
and packet rates increased by about 3%.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This change creates a separate function for functionality similar to
pskb_pull_tail. The main motivation for moving it to a separate function
is so that later I can just skip this function in the case where we have
already copied the buffer into skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This patch makes it so that we will always have ownership of the buffers by
the time we get to ixgbe_add_rx_frag. This is necessary as I am planning to
add a copy-break to ixgbe_add_rx_frag and in order for that to function
correctly we need the CPU to have ownership of the buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This change makes it so that we do not use double buffering if the page
size is larger than 4K. Instead we will simply walk through the page using
up to 3K per receive, and if we receive less than we only move the offset
by that amount. We will free the page when there is no longer any space
left that we can use instead of checking the page count to see if we can
cycle back to the start.
The main motivation behind this is to avoid the unnecessary truesize cost
for using a half page when most packets are 2K or smaller. With this new
approach the largest possible truesize for a page fragment will be 3K when
PAGE_SIZE is larger than 4K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This patch combines ixgbe_add_rx_frag and ixgbe_can_reuse_page into a
single function. The main motivation behind this is to make better use of
the values so that we don't have to load them from memory and into
registers twice.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This change reverts an earlier patch that introduced
ixgbe_init_rx_page_offset. The idea behind the function was to provide
some variation in the starting offset for the page in order to reduce
hot-spots in the cache. However it doesn't appear to provide any
significant benefit in the testing I have done. It has however been a
source of several bugs, and it blocks us from being able to use 2K
fragments on larger page sizes. So the decision I made was to remove it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This patch adds missing braces around the 10gig link check to include the check for KR support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Sascha Wildner <saw@online.de>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used. If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.
It works by reintroducing and expanding the skb_alloc_page() API to take
an skb. If the page was allocated from pfmemalloc reserves, it is
automatically copied. If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.
Failure to do so is not critical. The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.
[davem@davemloft.net: API rename and consistency]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch makes use of skb->data on Tx and the virtual address of the pages
allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change makes it so that we can use 1TC DCB in the case of MSI and
legacy interrupts. The advantage to this is that it allows us to fully
support FCoE w/ DCB instead of having to drop to link flow control only
when using these interrupt modes.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for a new 82599 device that supports WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
With DCB and FCoE configured extra queues may be allocated and
never used. After this patch we calculate the max correctly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Do RAR entry accounting correctly so that errors are reported and
promisc mode is set correctly when the number of entries exceeds
the hardware limits.
This can happen with many macvlan devices attached to the PF or
by adding many fdb entries in SR-IOV modes.
Also this includes a small refactor to fdb_add() to avoid having so
many nested if/else statements after adding a check for the number
or RAR entries.
The max entries for the PF is currently 16 we allow 15 additional
entries to account for the defined MAC.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so the function ixgbe_dcb_get_tc_from_up will use the
num_tcs.pg_tcs to determine the starting value for determining a traffic
class based on a user priority. The main motivation for this change is to
address possible bad configurations in which more TCs worth of data are
populated then there are actual TCs. By limiting this value we can at
least make certain we are not providing a map with values that are out of
range.
As a result any user priorities that are setup in the configuration with a
traffic class mapping higher than what the hardware supports will be
reported as being on TC 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The recent changes to netdev_alloc_skb actually make it so that the size of
the buffer now actually has a more direct input on the truesize. So in
order to make best use of the piece of a page we are allocated I am
reducing the IXGBE_RX_HDR_SIZE to 256 so that our truesize will be reduced
by 256 bytes as well.
This should result in performance improvements since the number of uses per
page should increase from 4 to 6 in the case of a 4K page. In addition we
should see socket performance improvements due to the truesize dropping
to less than 1K for buffers less than 256 bytes.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that we can use the atr_sample_rate to determine if
we are capable of supporting ATR. The advantage to this approach is that it
allows us to now determine the setting of the IXGBE_FLAG_FDIR_HASH_CAPABLE
based on the queueing scheme, instead of the queueing scheme being based on
the flag.
Using this approach there are essentially 5 conditions that must be checked
prior to trying to enable ATR:
1. Is SR-IOV disabled?
2. Are the number of TCs <= 1?
3. Is RSS queueing limit greater than 1?
4. Is atr_sample_rate set?
5. Is Flow Director perfect filtering disabled?
If any of these conditions are enabled they should disable ATR filtering.
Note that in the case of conditions 1 through 4 being met we will set
things up for ATR queueing, however if test 5 fails we will still leave the
queues allocated for use by perfect filters. The reason for this is to
allow for us to switch back and forth between ntuple and ATR without
needing to reallocate the descriptor rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch does two things. First it drops the unnecessary work of
searching for enabled VFs when we first bring up the adapter and instead
just uses pci_num_vf to determine how many VFs are enabled on the adapter.
The second thing it does is drop the use of vfdev from the vf_data_storage
structure. Instead we just search the entire system for a VF that has us
as it's PF, and then if that VF is assigned we indicate that the VFs are
assigned. This allows us to still check for assigned VFs even if the
vfinfo allocation has failed, or vfinfo has been freed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is meant to fix a bug in which we were not checking for pre-existing
VFs if we were not setting the max_vfs value at driver load. What happens
now is that we always call ixgbe_enable_sriov and this checks for
pre-existing VFs ore requested VFs prior to deciding on no SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jerr Kirsher says:
====================
This series contains updates to ixgbe.
...
Alexander Duyck (9):
ixgbe: Use VMDq offset to indicate the default pool
ixgbe: Fix memory leak when SR-IOV VFs are direct assigned
ixgbe: Drop references to deprecated pci_ DMA api and instead use
dma_ API
ixgbe: Cleanup configuration of FCoE registers
ixgbe: Merge all FCoE percpu values into a single structure
ixgbe: Make FCoE allocation and configuration closer to how rings
work
ixgbe: Correctly set SAN MAC RAR pool to default pool of PF
ixgbe: Only enable anti-spoof on VF pools
ixgbe: Enable FCoE FSO and CRC offloads based on CAPABLE instead of
ENABLED flag
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use PCI_VENDOR_ID_INTEL from pci_ids.h instead of creating its own
vendor ID #define.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of only setting the FCOE segmentation offload and CRC offload flags
if we enable FCoE, we could just set them always since there are no
modifications needed to the hardware or adapter FCoE structure in order to
use these features.
The advantage to this is that if FCoE enablement fails, for example because
SR-IOV was enabled on 82599, we will still have use of the FCoE
segmentation offload and Tx/Rx CRC offloads which should still help to
improve the FCoE performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
