summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel
AgeCommit message (Collapse)Author
2018-11-10igb: Remove superfluous reset to PHY and page 0 selectionChristian Grönke
[ Upstream commit 2a83fba6cae89dd9c0625e68ff8ffff791c67ac0 ] This patch reverts two previous applied patches to fix an issue that appeared when using SGMII based SFP modules. In the current state the driver will try to reset the PHY before obtaining the phy_addr of the SGMII attached PHY. That leads to an error in e1000_write_phy_reg_sgmii_82575. Causing the initialization to fail: igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k igb: Copyright (c) 2007-2014 Intel Corporation. igb: probe of ????:??:??.? failed with error -3 The patches being reverted are: commit 182785335447957409282ca745aa5bc3968facee Author: Aaron Sierra <asierra@xes-inc.com> Date: Tue Nov 29 10:03:56 2016 -0600 igb: reset the PHY before reading the PHY ID commit 440aeca4b9858248d8f16d724d9fa87a4f65fa33 Author: Matwey V Kornilov <matwey@sai.msu.ru> Date: Thu Nov 24 13:32:48 2016 +0300 igb: Explicitly select page 0 at initialization The first reverted patch directly causes the problem mentioned above. In case of SGMII the phy_addr is not known at this point and will only be obtained by 'igb_get_phy_id_82575' further down in the code. The second removed patch selects forces selection of page 0 in the PHY. Something that the reset tries to address as well. As pointed out by Alexander Duzck, the patch below fixes the same issue but in the proper location: commit 4e684f59d760a2c7c716bb60190783546e2d08a1 Author: Chris J Arges <christopherarges@gmail.com> Date: Wed Nov 2 09:13:42 2016 -0500 igb: Workaround for igb i210 firmware issue Reverts: 440aeca4b9858248d8f16d724d9fa87a4f65fa33. Reverts: 182785335447957409282ca745aa5bc3968facee. Signed-off-by: Christian Grönke <c.groenke@infodas.de> Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2018-10-03e1000: ensure to free old tx/rx rings in set_ringparam()Bo Chen
[ Upstream commit ee400a3f1bfe7004a3e14b81c38ccc5583c26295 ] In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value and the old tx/rx rings are freed only when the device is up. There are resource leaks on old tx/rx rings when the device is not up. This bug is reported by COD, a tool for testing kernel module binaries I am building. This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in 'e1000_set_ringparam()'. Signed-off-by: Bo Chen <chenbo@pdx.edu> Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-03e1000: check on netif_running() before calling e1000_up()Bo Chen
[ Upstream commit cf1acec008f8d7761aa3fd7c4bca7e17b2d2512d ] When the device is not up, the call to 'e1000_up()' from the error handling path of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer dereference. The null-pointer dereference is triggered in function 'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'. This bug was reported by COD, a tool for testing kernel module binaries I am building. This bug was also detected by KFI from Dr. Kai Cong. This patch fixes the bug by checking on 'netif_running()' before calling 'e1000_up()' in 'e1000_set_ringparam()'. Signed-off-by: Bo Chen <chenbo@pdx.edu> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26e1000e: Fix link check race conditionBenjamin Poirier
commit e2710dbf0dc1e37d85368e2404049dadda848d5a upstream. Alex reported the following race condition: /* link goes up... interrupt... schedule watchdog */ \ e1000_watchdog_task \ e1000e_has_link \ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link \ e1000e_phy_has_link_generic(..., &link) link = true /* link goes down... interrupt */ \ e1000_msix_other hw->mac.get_link_status = true /* link is up */ mac->get_link_status = false link_active = true /* link_active is true, wrongly, and stays so because * get_link_status is false */ Avoid this problem by making sure that we don't set get_link_status = false after having checked the link. It seems this problem has been present since the introduction of e1000e. Link: https://lkml.org/lkml/2018/1/29/338 Reported-by: Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Yanhui He <yanhuih@vmware.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26Revert "e1000e: Separate signaling for link check/link up"Benjamin Poirier
commit 3016e0a0c91246e55418825ba9aae271be267522 upstream. This reverts commit 19110cfbb34d4af0cdfe14cd243f3b09dc95b013. This reverts commit 4110e02eb45ea447ec6f5459c9934de0a273fb91. This reverts commit d3604515c9eda464a92e8e67aae82dfe07fe3c98. Commit 19110cfbb34d ("e1000e: Separate signaling for link check/link up") changed what happens to the link status when there is an error which happens after "get_link_status = false" in the copper check_for_link callbacks. Previously, such an error would be ignored and the link considered up. After that commit, any error implies that the link is down. Revert commit 19110cfbb34d ("e1000e: Separate signaling for link check/link up") and its followups. After reverting, the race condition described in the log of commit 19110cfbb34d is reintroduced. It may still be triggered by LSC events but this should keep the link down in case the link is electrically unstable, as discussed. The race may no longer be triggered by RXO events because commit 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts") restored reading icr in the Other handler. Link: https://lkml.org/lkml/2018/3/1/789 Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Yanhui He <yanhuih@vmware.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26e1000e: Avoid missed interrupts following ICR readBenjamin Poirier
commit 116f4a640b3197401bc93b8adc6c35040308ceff upstream. The 82574 specification update errata 12 states that interrupts may be missed if ICR is read while INT_ASSERTED is not set. Avoid that problem by setting all bits related to events that can trigger the Other interrupt in IMS. The Other interrupt is raised for such events regardless of whether or not they are set in IMS. However, only when they are set is the INT_ASSERTED bit also set in ICR. By doing this, we ensure that INT_ASSERTED is always set when we read ICR in e1000_msix_other() and steer clear of the errata. This also ensures that ICR will automatically be cleared on read, therefore we no longer need to clear bits explicitly. Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [bwh: Backported to 4.9: adjust context] Cc: Yanhui He <yanhuih@vmware.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26e1000e: Fix queue interrupt re-raising in Other interruptBenjamin Poirier
commit 361a954e6a7215de11a6179ad9bdc07d7e394b04 upstream. Restores the ICS write for Rx/Tx queue interrupts which was present before commit 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1) but was not restored in commit 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1). This re-raises the queue interrupts in case the txq or rxq bits were set in ICR and the Other interrupt handler read and cleared ICR before the queue interrupt was raised. Fixes: 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Yanhui He <yanhuih@vmware.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26Partial revert "e1000e: Avoid receiver overrun interrupt bursts"Benjamin Poirier
commit 1f0ea19722ef9dfa229a9540f70b8d1c34a98a6a upstream. This partially reverts commit 4aea7a5c5e940c1723add439f4088844cd26196d. We keep the fix for the first part of the problem (1) described in the log of that commit, that is to read ICR in the other interrupt handler. We remove the fix for the second part of the problem (2), Other interrupt throttling. Bursts of "Other" interrupts may once again occur during rxo (receive overflow) traffic conditions. This is deemed acceptable in the interest of avoiding unforeseen fallout from changes that are not strictly necessary. As discussed, the e1000e driver should be in "maintenance mode". Link: https://www.spinics.net/lists/netdev/msg480675.html Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Yanhui He <yanhuih@vmware.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-26e1000e: Remove Other from EIACBenjamin Poirier
commit 745d0bd3af99ccc8c5f5822f808cd133eadad6ac upstream. It was reported that emulated e1000e devices in vmware esxi 6.5 Build 7526125 do not link up after commit 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1). Some tracing shows that after e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other() on emulated e1000e devices. In comparison, on real e1000e 82574 hardware, icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation. Some experimentation showed that this flaw in vmware e1000e emulation can be worked around by not setting Other in EIAC. This is how it was before 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1). Fixes: 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [bwh: Backported to 4.9: adjust context] Cc: Yanhui He <yanhuih@vmware.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-24ixgbe: Be more careful when modifying MAC filtersAlexander Duyck
[ Upstream commit d14c780c11fbc10f66c43e7b64eefe87ca442bd3 ] This change makes it so that we are much more explicit about the ordering of updates to the receive address register (RAR) table. Prior to this patch I believe we may have been updating the table while entries were still active, or possibly allowing for reordering of things since we weren't explicitly flushing writes to either the lower or upper portion of the register prior to accessing the other half. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-03ixgbevf: fix MAC address changes through ixgbevf_set_mac()Emil Tantilov
[ Upstream commit 6e7d0ba1e59b1a306761a731e67634c0f2efea2a ] Set hw->mac.perm_addr in ixgbevf_set_mac() in order to avoid losing the custom MAC on reset. This can happen in the following case: >ip link set $vf address $mac >ethtool -r $vf Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-30e1000e: allocate ring descriptors with dma_zalloc_coherentPierre-Yves Kerbrat
[ Upstream commit aea3fca005fb45f80869f2e8d56fd4e64c1d1fdb ] Descriptor rings were not initialized at zero when allocated When area contained garbage data, it caused skb_over_panic in e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set) This patch makes use of dma_zalloc_coherent to make sure the ring is memset at 0 to prevent the area from containing garbage. Following is the signature of the panic: IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0 IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()! IODDR0@0.0: Kernel panic - not syncing: BUG! IODDR0@0.0: IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0) IODDR0@0.0: SP = <815a1c0c> IODDR0@0.0: Stack: 00000001 IODDR0@0.0: b2d89800 815e33ac IODDR0@0.0: ea73c040 00000001 IODDR0@0.0: 60040003 0000fa0a IODDR0@0.0: 00000002 IODDR0@0.0: IODDR0@0.0: 804540c0 815a1c70 IODDR0@0.0: b2744000 602ac070 IODDR0@0.0: 815a1c44 b2d89800 IODDR0@0.0: 8173cc00 815a1c08 IODDR0@0.0: IODDR0@0.0: 00000006 IODDR0@0.0: 815a1b50 00000000 IODDR0@0.0: 80079434 00000001 IODDR0@0.0: ab46df40 b2744000 IODDR0@0.0: b2d89800 IODDR0@0.0: IODDR0@0.0: 0000fa0a 8045745c IODDR0@0.0: 815a1c88 0000fa0a IODDR0@0.0: 80407b20 b2789f80 IODDR0@0.0: 00000005 80407b20 IODDR0@0.0: IODDR0@0.0: IODDR0@0.0: Call Trace: IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8 IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0 IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0 IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8 IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8 IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8 IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8 IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8 IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288 IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8 IODDR0@0.0: ... IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace) IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG! Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu> Signed-off-by: Marius Gligor <mgligor@kalray.eu> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-30e1000e: Fix check_for_link return value with autoneg offBenjamin Poirier
[ Upstream commit 4e7dc08e57c95673d2edaba8983c3de4dd1f65f5 ] When autoneg is off, the .check_for_link callback functions clear the get_link_status flag and systematically return a "pseudo-error". This means that the link is not detected as up until the next execution of the e1000_watchdog_task() 2 seconds later. Fixes: 19110cfbb34d ("e1000e: Separate signaling for link check/link up") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-30fm10k: fix "failed to kill vid" message for VFNgai-Mint Kwan
[ Upstream commit cf315ea596ec26d7aa542a9ce354990875a920c0 ] When a VF is under PF VLAN assignment: ip link set <pf> vf <#> vlan <vid> This will remove all previous entries in the VLAN table including those generated by VLAN interfaces created on the VF. The issue arises when the VF is under PF VLAN assignment and one or more of these VLAN interfaces of the VF are deleted. When deleting these VLAN interfaces, the following message will be generated in "dmesg": failed to kill vid 0081/<vid> for device <vf> This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error. The handler for this ndo is "fm10k_update_vid". Any calls to this function while under PF VLAN management will exit prematurely and, thus, it will generate the failure message. Additionally, since "fm10k_update_vid" exits prematurely, none of the VLAN update is performed. So, even though the actual VLAN interfaces of the VF will be deleted, the active_vlans bitmask is not cleared. When the VF is no longer under PF VLAN assignment, the driver mistakenly restores the previous entries of the VLAN table based on an unsynchronized list of active VLANs. The solution to this issue involves checking the VLAN update action type before exiting "fm10k_update_vid". If the VLAN update action type is to "add", this action will not be permitted while the VF is under PF VLAN assignment and the VLAN update is abandoned like before. However, if the VLAN update action type is to "kill", then we need to also clear the active_vlans bitmask. However, we don't need to actually queue any messages to the PF, because the MAC and VLAN tables have already been cleared, and the PF would silently ignore these requests anyways. Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-13e1000e: Undo e1000e_pm_freeze if __e1000_shutdown failsChris Wilson
[ Upstream commit 833521ebc65b1c3092e5c0d8a97092f98eec595d ] An error during suspend (e100e_pm_suspend), [ 429.994338] ACPI : EC: event blocked [ 429.994633] e1000e: EEE TX LPI TIMER: 00000011 [ 430.955451] pci_pm_suspend(): e1000e_pm_suspend+0x0/0x30 [e1000e] returns -2 [ 430.955454] dpm_run_callback(): pci_pm_suspend+0x0/0x140 returns -2 [ 430.955458] PM: Device 0000:00:19.0 failed to suspend async: error -2 [ 430.955581] PM: Some devices failed to suspend, or early wake event detected [ 430.957709] ACPI : EC: event unblocked lead to complete failure: [ 432.585002] ------------[ cut here ]------------ [ 432.585013] WARNING: CPU: 3 PID: 8372 at kernel/irq/manage.c:1478 __free_irq+0x9f/0x280 [ 432.585015] Trying to free already-free IRQ 20 [ 432.585016] Modules linked in: cdc_ncm usbnet x86_pkg_temp_thermal intel_powerclamp coretemp mii crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep lpc_ich snd_hda_core snd_pcm mei_me mei sdhci_pci sdhci i915 mmc_core e1000e ptp pps_core prime_numbers [ 432.585042] CPU: 3 PID: 8372 Comm: kworker/u16:40 Tainted: G U 4.10.0-rc8-CI-Patchwork_3870+ #1 [ 432.585044] Hardware name: LENOVO 2356GCG/2356GCG, BIOS G7ET31WW (1.13 ) 07/02/2012 [ 432.585050] Workqueue: events_unbound async_run_entry_fn [ 432.585051] Call Trace: [ 432.585058] dump_stack+0x67/0x92 [ 432.585062] __warn+0xc6/0xe0 [ 432.585065] warn_slowpath_fmt+0x4a/0x50 [ 432.585070] ? _raw_spin_lock_irqsave+0x49/0x60 [ 432.585072] __free_irq+0x9f/0x280 [ 432.585075] free_irq+0x34/0x80 [ 432.585089] e1000_free_irq+0x65/0x70 [e1000e] [ 432.585098] e1000e_pm_freeze+0x7a/0xb0 [e1000e] [ 432.585106] e1000e_pm_suspend+0x21/0x30 [e1000e] [ 432.585113] pci_pm_suspend+0x71/0x140 [ 432.585118] dpm_run_callback+0x6f/0x330 [ 432.585122] ? pci_pm_freeze+0xe0/0xe0 [ 432.585125] __device_suspend+0xea/0x330 [ 432.585128] async_suspend+0x1a/0x90 [ 432.585132] async_run_entry_fn+0x34/0x160 [ 432.585137] process_one_work+0x1f4/0x6d0 [ 432.585140] ? process_one_work+0x16e/0x6d0 [ 432.585143] worker_thread+0x49/0x4a0 [ 432.585145] kthread+0x107/0x140 [ 432.585148] ? process_one_work+0x6d0/0x6d0 [ 432.585150] ? kthread_create_on_node+0x40/0x40 [ 432.585154] ret_from_fork+0x2e/0x40 [ 432.585156] ---[ end trace 6712df7f8c4b9124 ]--- The unwind failures stems from commit 2800209994f8 ("e1000e: Refactor PM flows"), but it may be a later patch that introduced the non-recoverable behaviour. Fixes: 2800209994f8 ("e1000e: Refactor PM flows") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99847 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-13igb: fix race condition with PTP_TX_IN_PROGRESS bitsJacob Keller
[ Upstream commit 4ccdc013b0ae04755a8f7905e0525955d52a77d0 ] Hardware related to the igb driver has a limitation of only handling one Tx timestamp at a time. Thus, the driver uses a state bit lock to enforce that only one timestamp request is honored at a time. Unfortunately this suffers from a simple race condition. The bit lock is not cleared until after skb_tstamp_tx() is called notifying the stack of a new Tx timestamp. Even a well behaved application which sends only one timestamp request at once and waits for a response might wake up and send a new packet before the bit lock is cleared. This results in needlessly dropping some Tx timestamp requests. We can fix this by unlocking the state bit as soon as we read the Timestamp register, as this is the first point at which it is safe to unlock. To avoid issues with the skb pointer, we'll use a copy of the pointer and set the global variable in the driver structure to NULL first. This ensures that the next timestamp request does not modify our local copy of the skb pointer. This ensures that well behaved applications do not accidentally race with the unlock bit. Obviously an application which sends multiple Tx timestamp requests at once will still only timestamp one packet at a time. Unfortunately there is nothing we can do about this. Reported-by: David Mirabito <davidm@metamako.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-13e1000e: fix race condition around skb_tstamp_tx()Jacob Keller
[ Upstream commit 5012863b7347866764c4a4e58b62fb05346b0d06 ] The e1000e driver and related hardware has a limitation on Tx PTP packets which requires we limit to timestamping a single packet at once. We do this by verifying that we never request a new Tx timestamp while we still have a tx_hwtstamp_skb pointer. Unfortunately the driver suffers from a race condition around this. The tx_hwtstamp_skb pointer is not set to NULL until after skb_tstamp_tx() is called. This function notifies the stack and applications of a new timestamp. Even a well behaved application that only sends a new request when the first one is finished might be woken up and possibly send a packet before we can free the timestamp in the driver again. The result is that we needlessly ignore some Tx timestamp requests in this corner case. Fix this by assigning the tx_hwtstamp_skb pointer prior to calling skb_tstamp_tx() and use a temporary pointer to hold the timestamped skb until that function finishes. This ensures that the application is not woken up until the driver is ready to begin timestamping a new packet. This ensures that well behaved applications do not accidentally race with condition to skip Tx timestamps. Obviously an application which sends multiple Tx timestamp requests at once will still only timestamp one packet at a time. Unfortunately there is nothing we can do about this. Reported-by: David Mirabito <davidm@metamako.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-13i40evf: fix merge error in older patchJesse Brandeburg
[ Upstream commit 155b0f690051345deefc653774b739c786067d61 ] This patch fixes a missing line that was missed while merging, which results in a driver feature in the VF not working to enable RSS as a negotiated feature. Fixes: 43a3d9ba34c9c ("i40evf: Allow PF driver to configure RSS") Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24ixgbevf: fix size of queue stats lengthEmil Tantilov
[ Upstream commit f87fc44770f54ff1b54d44ae9cec11f10efeca02 ] IXGBEVF_QUEUE_STATS_LEN is based on ixgebvf_stats, not ixgbe_stats. This change fixes a bug where ethtool -S displayed some empty fields. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24e1000e: fix timing for 82579 Gigabit Ethernet controllerBernd Faust
[ Upstream commit 5313eeccd2d7f486be4e5c7560e3e2be239ec8f7 ] After an upgrade to Linux kernel v4.x the hardware timestamps of the 82579 Gigabit Ethernet Controller are different than expected. The values that are being read are almost four times as big as before the kernel upgrade. The difference is that after the upgrade the driver sets the clock frequency to 25MHz, where before the upgrade it was set to 96MHz. Intel confirmed that the correct frequency for this network adapter is 96MHz. Signed-off-by: Bernd Faust <berndfaust@gmail.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22i40e: only register client on iWarp-capable devicesMitch Williams
[ Upstream commit 004eb614c4d2fcc12a98714fd887a860582f203a ] The client interface is only intended for use on devices that support iWarp. Only register with the client if this is the case. This fixes a panic when loading i40iw on X710 devices. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Reported-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22fm10k: correctly check if interface is removedPhil Turnbull
[ Upstream commit 540fca35e38d15777b310f450f63f056e63039f5 ] FM10K_REMOVED expects a hardware address, not a 'struct fm10k_hw'. Fixes: 5cb8db4a4cbc ("fm10k: Add support for VF") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22i40e/i40evf: Fix use after free in Rx cleanup pathAlexander Duyck
[ Upstream commit 741b8b832a57402380be79d7d11a59eaf57fff3b ] We need to reset skb back to NULL when we have freed it in the Rx cleanup path. I found one spot where this wasn't occurring so this patch fixes it. Change-ID: Iaca68934200732cd4a63eb0bd83b539c95f8c4dd Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22i40e: fix ethtool to get EEPROM data from X722 interfaceLihong Yang
[ Upstream commit c271dd6c391b535226cf1a81aaad9f33cb5899d3 ] Currently ethtool -e will error out with a X722 interface as its EEPROM has a scope limit at offset 0x5B9FFF. This patch fixes the issue by setting the EEPROM length to the scope limit to avoid NVM read failure beyond that. Change-ID: I0b7d4dd6c7f2a57cace438af5dffa0f44c229372 Signed-off-by: Lihong Yang <lihong.yang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22i40e: Acquire NVM lock before reads on all devicesAaron Salter
[ Upstream commit 96a39aed25e6559b160786117df124084feb9080 ] Acquire NVM lock before reads on all devices. Previously, locks were only used for X722 and later. Fixes an issue where simultaneous X710 NVM accesses were interfering with each other. Change-ID: If570bb7acf958cef58725ec2a2011cead6f80638 Signed-off-by: Aaron Salter <aaron.k.salter@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-03i40e/i40evf: Account for frags split over multiple descriptors in check ↵Alexander Duyck
linearize [ Upstream commit 248de22e638f10bd5bfc7624a357f940f66ba137 ] The original code for __i40e_chk_linearize didn't take into account the fact that if a fragment is 16K in size or larger it has to be split over 2 descriptors and the smaller of those 2 descriptors will be on the trailing edge of the transmit. As a result we can get into situations where we didn't catch requests that could result in a Tx hang. This patch takes care of that by subtracting the length of all but the trailing edge of the stale fragment before we test for sum. By doing this we can guarantee that we have all cases covered, including the case of a fragment that spans multiple descriptors. We don't need to worry about checking the inner portions of this since 12K is the maximum aligned DMA size and that is larger than any MSS will ever be since the MTU limit for jumbos is something on the order of 9K. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-03e1000: fix disabling already-disabled warningTushar Dave
[ Upstream commit 0b76aae741abb9d16d2c0e67f8b1e766576f897d ] This patch adds check so that driver does not disable already disabled device. [ 44.637743] advantechwdt: Unexpected close, not stopping watchdog! [ 44.997548] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6 [ 45.013419] e1000 0000:00:03.0: disabling already-disabled device [ 45.013447] ------------[ cut here ]------------ [ 45.014868] WARNING: CPU: 1 PID: 71 at drivers/pci/pci.c:1641 pci_disable_device+0xa1/0x105: pci_disable_device at drivers/pci/pci.c:1640 [ 45.016171] CPU: 1 PID: 71 Comm: rcu_perf_shutdo Not tainted 4.14.0-01330-g3c07399 #1 [ 45.017197] task: ffff88011bee9e40 task.stack: ffffc90000860000 [ 45.017987] RIP: 0010:pci_disable_device+0xa1/0x105: pci_disable_device at drivers/pci/pci.c:1640 [ 45.018603] RSP: 0000:ffffc90000863e30 EFLAGS: 00010286 [ 45.019282] RAX: 0000000000000035 RBX: ffff88013a230008 RCX: 0000000000000000 [ 45.020182] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000203 [ 45.021084] RBP: ffff88013a3f31e8 R08: 0000000000000001 R09: 0000000000000000 [ 45.021986] R10: ffffffff827ec29c R11: 0000000000000002 R12: 0000000000000001 [ 45.022946] R13: ffff88013a230008 R14: ffff880117802b20 R15: ffffc90000863e8f [ 45.023842] FS: 0000000000000000(0000) GS:ffff88013fd00000(0000) knlGS:0000000000000000 [ 45.024863] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 45.025583] CR2: ffffc900006d4000 CR3: 000000000220f000 CR4: 00000000000006a0 [ 45.026478] Call Trace: [ 45.026811] __e1000_shutdown+0x1d4/0x1e2: __e1000_shutdown at drivers/net/ethernet/intel/e1000/e1000_main.c:5162 [ 45.027344] ? rcu_perf_cleanup+0x2a1/0x2a1: rcu_perf_shutdown at kernel/rcu/rcuperf.c:627 [ 45.027883] e1000_shutdown+0x14/0x3a: e1000_shutdown at drivers/net/ethernet/intel/e1000/e1000_main.c:5235 [ 45.028351] device_shutdown+0x110/0x1aa: device_shutdown at drivers/base/core.c:2807 [ 45.028858] kernel_power_off+0x31/0x64: kernel_power_off at kernel/reboot.c:260 [ 45.029343] rcu_perf_shutdown+0x9b/0xa7: rcu_perf_shutdown at kernel/rcu/rcuperf.c:637 [ 45.029852] ? __wake_up_common_lock+0xa2/0xa2: autoremove_wake_function at kernel/sched/wait.c:376 [ 45.030414] kthread+0x126/0x12e: kthread at kernel/kthread.c:233 [ 45.030834] ? __kthread_bind_mask+0x8e/0x8e: kthread at kernel/kthread.c:190 [ 45.031399] ? ret_from_fork+0x1f/0x30: ret_from_fork at arch/x86/entry/entry_64.S:443 [ 45.031883] ? kernel_init+0xa/0xf5: kernel_init at init/main.c:997 [ 45.032325] ret_from_fork+0x1f/0x30: ret_from_fork at arch/x86/entry/entry_64.S:443 [ 45.032777] Code: 00 48 85 ed 75 07 48 8b ab a8 00 00 00 48 8d bb 98 00 00 00 e8 aa d1 11 00 48 89 ea 48 89 c6 48 c7 c7 d8 e4 0b 82 e8 55 7d da ff <0f> ff b9 01 00 00 00 31 d2 be 01 00 00 00 48 c7 c7 f0 b1 61 82 [ 45.035222] ---[ end trace c257137b1b1976ef ]--- [ 45.037838] ACPI: Preparing to enter system sleep state S5 Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com> Tested-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-03igb: Free IRQs when device is hotpluggedLyude Paul
commit 888f22931478a05bc81ceb7295c626e1292bf0ed upstream. Recently I got a Caldigit TS3 Thunderbolt 3 dock, and noticed that upon hotplugging my kernel would immediately crash due to igb: [ 680.825801] kernel BUG at drivers/pci/msi.c:352! [ 680.828388] invalid opcode: 0000 [#1] SMP [ 680.829194] Modules linked in: igb(O) thunderbolt i2c_algo_bit joydev vfat fat btusb btrtl btbcm btintel bluetooth ecdh_generic hp_wmi sparse_keymap rfkill wmi_bmof iTCO_wdt intel_rapl x86_pkg_temp_thermal coretemp crc32_pclmul snd_pcm rtsx_pci_ms mei_me snd_timer memstick snd pcspkr mei soundcore i2c_i801 tpm_tis psmouse shpchp wmi tpm_tis_core tpm video hp_wireless acpi_pad rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci mfd_core xhci_pci xhci_hcd i2c_hid i2c_core [last unloaded: igb] [ 680.831085] CPU: 1 PID: 78 Comm: kworker/u16:1 Tainted: G O 4.15.0-rc3Lyude-Test+ #6 [ 680.831596] Hardware name: HP HP ZBook Studio G4/826B, BIOS P71 Ver. 01.03 06/09/2017 [ 680.832168] Workqueue: kacpi_hotplug acpi_hotplug_work_fn [ 680.832687] RIP: 0010:free_msi_irqs+0x180/0x1b0 [ 680.833271] RSP: 0018:ffffc9000030fbf0 EFLAGS: 00010286 [ 680.833761] RAX: ffff8803405f9c00 RBX: ffff88033e3d2e40 RCX: 000000000000002c [ 680.834278] RDX: 0000000000000000 RSI: 00000000000000ac RDI: ffff880340be2178 [ 680.834832] RBP: 0000000000000000 R08: ffff880340be1ff0 R09: ffff8803405f9c00 [ 680.835342] R10: 0000000000000000 R11: 0000000000000040 R12: ffff88033d63a298 [ 680.835822] R13: ffff88033d63a000 R14: 0000000000000060 R15: ffff880341959000 [ 680.836332] FS: 0000000000000000(0000) GS:ffff88034f440000(0000) knlGS:0000000000000000 [ 680.836817] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 680.837360] CR2: 000055e64044afdf CR3: 0000000001c09002 CR4: 00000000003606e0 [ 680.837954] Call Trace: [ 680.838853] pci_disable_msix+0xce/0xf0 [ 680.839616] igb_reset_interrupt_capability+0x5d/0x60 [igb] [ 680.840278] igb_remove+0x9d/0x110 [igb] [ 680.840764] pci_device_remove+0x36/0xb0 [ 680.841279] device_release_driver_internal+0x157/0x220 [ 680.841739] pci_stop_bus_device+0x7d/0xa0 [ 680.842255] pci_stop_bus_device+0x2b/0xa0 [ 680.842722] pci_stop_bus_device+0x3d/0xa0 [ 680.843189] pci_stop_and_remove_bus_device+0xe/0x20 [ 680.843627] trim_stale_devices+0xf3/0x140 [ 680.844086] trim_stale_devices+0x94/0x140 [ 680.844532] trim_stale_devices+0xa6/0x140 [ 680.845031] ? get_slot_status+0x90/0xc0 [ 680.845536] acpiphp_check_bridge.part.5+0xfe/0x140 [ 680.846021] acpiphp_hotplug_notify+0x175/0x200 [ 680.846581] ? free_bridge+0x100/0x100 [ 680.847113] acpi_device_hotplug+0x8a/0x490 [ 680.847535] acpi_hotplug_work_fn+0x1a/0x30 [ 680.848076] process_one_work+0x182/0x3a0 [ 680.848543] worker_thread+0x2e/0x380 [ 680.848963] ? process_one_work+0x3a0/0x3a0 [ 680.849373] kthread+0x111/0x130 [ 680.849776] ? kthread_create_worker_on_cpu+0x50/0x50 [ 680.850188] ret_from_fork+0x1f/0x30 [ 680.850601] Code: 43 14 85 c0 0f 84 d5 fe ff ff 31 ed eb 0f 83 c5 01 39 6b 14 0f 86 c5 fe ff ff 8b 7b 10 01 ef e8 b7 e4 d2 ff 48 83 78 70 00 74 e3 <0f> 0b 49 8d b5 a0 00 00 00 e8 62 6f d3 ff e9 c7 fe ff ff 48 8b [ 680.851497] RIP: free_msi_irqs+0x180/0x1b0 RSP: ffffc9000030fbf0 As it turns out, normally the freeing of IRQs that would fix this is called inside of the scope of __igb_close(). However, since the device is already gone by the point we try to unregister the netdevice from the driver due to a hotplug we end up seeing that the netif isn't present and thus, forget to free any of the device IRQs. So: make sure that if we're in the process of dismantling the netdev, we always allow __igb_close() to be called so that IRQs may be freed normally. Additionally, only allow igb_close() to be called from __igb_close() if it hasn't already been called for the given adapter. Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: 9474933caf21 ("igb: close/suspend race in netif_device_detach") Cc: Todd Fujinaka <todd.fujinaka@intel.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-17e1000e: Fix e1000_check_for_copper_link_ich8lan return value.Benjamin Poirier
commit 4110e02eb45ea447ec6f5459c9934de0a273fb91 upstream. e1000e_check_for_copper_link() and e1000_check_for_copper_link_ich8lan() are the two functions that may be assigned to mac.ops.check_for_link when phy.media_type == e1000_media_type_copper. Commit 19110cfbb34d ("e1000e: Separate signaling for link check/link up") changed the meaning of the return value of check_for_link for copper media but only adjusted the first function. This patch adjusts the second function likewise. Reported-by: Christian Hesse <list@eworm.de> Reported-by: Gabriel C <nix.or.die@gmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=198047 Fixes: 19110cfbb34d ("e1000e: Separate signaling for link check/link up") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Tested-by: Christian Hesse <list@eworm.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-25fm10k: ensure we process SM mbx when processing VF mbxJacob Keller
[ Upstream commit 17a91809942ca32c70026d2d5ba3348a2c4fdf8f ] When we process VF mailboxes, the driver is likely going to also queue up messages to the switch manager. This process merely queues up the FIFO, but doesn't actually begin the transmission process. Because we hold the mailbox lock during this VF processing, the PF<->SM mailbox is not getting processed at this time. Ensure that we actually process the PF<->SM mailbox in between each PF<->VF mailbox. This should ensure prompt transmission of the messages queued up after each VF message is received and handled. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-25fm10k: fix mis-ordered parameters in declaration for .ndo_set_vf_bwJacob Keller
[ Upstream commit 3e256ac5b1ec307e5dd5a4c99fbdbc651446c738 ] We've had support for setting both a minimum and maximum bandwidth via .ndo_set_vf_bw since commit 883a9ccbae56 ("fm10k: Add support for SR-IOV to driver", 2014-09-20). Likely because we do not support minimum rates, the declaration mis-ordered the "unused" parameter, which causes warnings when analyzed with cppcheck. Fix this warning by properly declaring the min_rate and max_rate variables in the declaration and definition (rather than using "unused"). Also rename "rate" to max_rate so as to clarify that we only support setting the maximum rate. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-25ixgbe: fix use of uninitialized paddingEmil Tantilov
[ Upstream commit dcfd6b839c998bc9838e2a47f44f37afbdf3099c ] This patch is resolving Coverity hits where padding in a structure could be used uninitialized. - Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum() - Initialize buffer.pad2/3 before ixgbe_hic_unlocked() Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-25igb: check memory allocation failureChristophe JAILLET
[ Upstream commit 18eb86362a52f0af933cc0fd5e37027317eb2d1c ] Check memory allocation failures and return -ENOMEM in such cases, as already done for other memory allocations in this function. This avoids NULL pointers dereference. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-25i40e: Do not enable NAPI on q_vectors that have no ringsAlexander Duyck
[ Upstream commit 13a8cd191a2b470cfd435b3b57dbd21aa65ff78c ] When testing the epoll w/ busy poll code I found that I could get into a state where the i40e driver had q_vectors w/ active NAPI that had no rings. This was resulting in a divide by zero error. To correct it I am updating the driver code so that we only support NAPI on q_vectors that have 1 or more rings allocated to them. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30e1000e: Avoid receiver overrun interrupt burstsBenjamin Poirier
commit 4aea7a5c5e940c1723add439f4088844cd26196d upstream. When e1000e_poll() is not fast enough to keep up with incoming traffic, the adapter (when operating in msix mode) raises the Other interrupt to signal Receiver Overrun. This is a double problem because 1) at the moment e1000_msix_other() assumes that it is only called in case of Link Status Change and 2) if the condition persists, the interrupt is repeatedly raised again in quick succession. Ideally we would configure the Other interrupt to not be raised in case of receiver overrun but this doesn't seem possible on this adapter. Instead, we handle the first part of the problem by reverting to the practice of reading ICR in the other interrupt handler, like before commit 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt"). Thanks to commit 0a8047ac68e5 ("e1000e: Fix msi-x interrupt automask") which cleared IAME from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts anymore. We handle the second part of the problem by not re-enabling the Other interrupt right away when there is overrun. Instead, we wait until traffic subsides, napi polling mode is exited and interrupts are re-enabled. Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Fixes: 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30e1000e: Separate signaling for link check/link upBenjamin Poirier
commit 19110cfbb34d4af0cdfe14cd243f3b09dc95b013 upstream. Lennart reported the following race condition: \ e1000_watchdog_task \ e1000e_has_link \ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link /* link is up */ mac->get_link_status = false; /* interrupt */ \ e1000_msix_other hw->mac.get_link_status = true; link_active = !hw->mac.get_link_status /* link_active is false, wrongly */ This problem arises because the single flag get_link_status is used to signal two different states: link status needs checking and link status is down. Avoid the problem by using the return value of .check_for_link to signal the link status to e1000e_has_link(). Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30e1000e: Fix return value testBenjamin Poirier
commit d3509f8bc7b0560044c15f0e3ecfde1d9af757a6 upstream. All the helpers return -E1000_ERR_PHY. Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30e1000e: Fix error path in link detectionBenjamin Poirier
commit c4c40e51f9c32c6dd8adf606624c930a1c4d9bbb upstream. In case of error from e1e_rphy(), the loop will exit early and "success" will be set to true erroneously. Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30ixgbe: Fix skb list corruption on Power systemsBrian King
commit 0a9a17e3bb4564caf4bfe2a6783ae1287667d188 upstream. This patch fixes an issue seen on Power systems with ixgbe which results in skb list corruption and an eventual kernel oops. The following is what was observed: CPU 1 CPU2 ============================ ============================ 1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq 2: first->skb = skb eop_desc = tx_buffer->next_to_watch 3: ixgbe_tx_map read_barrier_depends() 4: wmb check adapter written status bit 5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..); 6: writel(i, tx_ring->tail); The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not get loaded prior to tx_buffer->next_to_watch, which then results in loading a stale skb pointer. This patch replaces the read_barrier_depends with smp_rmb to ensure loads are ordered with respect to the load of tx_buffer->next_to_watch. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30fm10k: Use smp_rmb rather than read_barrier_dependsBrian King
commit 7b8edcc685b5e2c3c37aa13dc50a88e84a5bfef8 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with fm10k as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30i40evf: Use smp_rmb rather than read_barrier_dependsBrian King
commit f72271e2a0ae4277d53c4053f5eed8bb346ba38a upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with i40evf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30ixgbevf: Use smp_rmb rather than read_barrier_dependsBrian King
commit ae0c585d93dfaf923d2c7eb44b2c3ab92854ea9b upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with ixgbevf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30igbvf: Use smp_rmb rather than read_barrier_dependsBrian King
commit 1e1f9ca546556e508d021545861f6b5fc75a95fe upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with igbvf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30igb: Use smp_rmb rather than read_barrier_dependsBrian King
commit c4cb99185b4cc96c0a1c70104dc21ae14d7e7f28 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with igb as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-30i40e: Use smp_rmb rather than read_barrier_dependsBrian King
commit 52c6912fde0133981ee50ba08808f257829c4c93 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with i40e as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-21ixgbe: do not disable FEC from the driverEmil Tantilov
[ Upstream commit 1fe954b2097bb907b4578e6a74e4c1d23785a601 ] FEC is configured by the NVM and the driver should not be overriding it. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-21ixgbe: add mask for 64 RSS queuesEmil Tantilov
[ Upstream commit 2bf1a87b903bd81b1448a1cef73de59fb6c4d340 ] The indirection table was reported incorrectly for X550 and newer where we can support up to 64 RSS queues. Reported-by Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-21ixgbe: Reduce I2C retry count on X550 devicesTony Nguyen
[ Upstream commit 3f0d646b720d541309b11e190db58086f446f41e ] A retry count of 10 is likely to run into problems on X550 devices that have to detect and reset unresponsive CS4227 devices. So, reduce the I2C retry count to 3 for X550 and above. This should avoid any possible regressions in existing devices. Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-21ixgbe: Fix reporting of 100Mb capabilityTony Nguyen
[ Upstream commit f215266470dfe86196a31fe0725a86cea77f9a18 ] BaseT adapters that are capable of supporting 100Mb are not reporting this capability. This patch corrects the reporting so that 100Mb is shown as supported on those adapters. Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-21ixgbe: handle close/suspend race with netif_device_detach/presentEmil Tantilov
[ Upstream commit f7f37e7ff2b9b7eff7fbd035569cab35896869a3 ] When an interface is part of a namespace it is possible that ixgbe_close() may be called while __ixgbe_shutdown() is running which ends up in a double free WARN and/or a BUG in free_msi_irqs(). To handle this situation we extend the rtnl_lock() to protect the call to netif_device_detach() and ixgbe_clear_interrupt_scheme() in __ixgbe_shutdown() and check for netif_device_present() to avoid clearing the interrupts second time in ixgbe_close(); Also extend the rtnl lock in ixgbe_resume() to netif_device_attach(). Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-16 15:31:25 +0000