summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/netronome
AgeCommit message (Collapse)Author
2018-09-26nfp: avoid buffer leak when FW communication failsJakub Kicinski
[ Upstream commit 07300f774fec9519663a597987a4083225588be4 ] After device is stopped we reset the rings by moving all free buffers to positions [0, cnt - 2], and clear the position cnt - 1 in the ring. We then proceed to clear the read/write pointers. This means that if we try to reset the ring again the code will assume that the next to fill buffer is at position 0 and swap it with cnt - 1. Since we previously cleared position cnt - 1 it will lead to leaking the first buffer and leaving ring in a bad state. This scenario can only happen if FW communication fails, in which case the ring will never be used again, so the fact it's in a bad state will not be noticed. Buffer leak is the only problem. Don't try to move buffers in the ring if the read/write pointers indicate the ring was never used or have already been reset. nfp_net_clear_config_and_disable() is now fully idempotent. Found by code inspection, FW communication failures are very rare, and reconfiguring a live device is not common either, so it's unlikely anyone has ever noticed the leak. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-19nfp: TX time stamp packets before HW doorbell is rungJakub Kicinski
commit 46f1c52e66dbc0d7a99f7c2a3c9debb497fe7b7b upstream. TX completion may happen any time after HW queue was kicked. We can't access the skb afterwards. Move the time stamping before ringing the doorbell. Fixes: 4c3523623dc0 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-30nfp: fix infinite loop on umapping cleanupColin Ian King
[ Upstream commit eac2c68d663effb077210218788952b5a0c1f60e ] The while loop that performs the dma page unmapping never decrements index counter f and hence loops forever. Fix this with a pre-decrement on f. Detected by CoverityScan, CID#1357309 ("Infinite loop") Fixes: 4c3523623dc0 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-30nfp: bpf: zero extend 4 byte context loadsJakub Kicinski
Set upper 32 bits of destination register to zeros after load from the context structure. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-26nfp: bpf: improve handling for disabled BPF syscallArnd Bergmann
I stumbled over a new warning during randconfig testing, with CONFIG_BPF_SYSCALL disabled: drivers/net/ethernet/netronome/nfp/nfp_net_offload.c: In function 'nfp_net_bpf_offload': drivers/net/ethernet/netronome/nfp/nfp_net_offload.c:263:3: error: '*((void *)&res+4)' may be used uninitialized in this function [-Werror=maybe-uninitialized] drivers/net/ethernet/netronome/nfp/nfp_net_offload.c:263:3: error: 'res.n_instr' may be used uninitialized in this function [-Werror=maybe-uninitialized] As far as I can tell, this is a false positive caused by the compiler getting confused about a function that is partially inlined, but it's easy to avoid while improving the code: The nfp_bpf_jit() stub helper for that configuration is unusual as it is defined in a header file but not marked 'static inline'. By moving the compile-time check into the caller using the IS_ENABLED() macro, we can remove that stub and simplify the nfp_net_bpf_offload_prepare() function enough to unconfuse the compiler. Fixes: 7533fdc0f77f ("nfp: bpf: add hardware bpf offload") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2016-09-21nfp: bpf: add offload of TC direct action modeJakub Kicinski
Add offload of TC in direct action mode. We just need to provide appropriate checks in the verifier and a new outro block to translate the exit codes to what data path expects Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-21nfp: bpf: add support for legacy redirect actionJakub Kicinski
Data path has redirect support so expressing redirect to the port frame came from is a trivial matter of setting the right result code. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-21nfp: bpf: add packet marking supportJakub Kicinski
Add missing ABI defines and eBPF instructions to allow mark to be passed on and extend prepend parsing on the RX path to pick it up from packet metadata. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-21nfp: bpf: allow offloaded filters to update statsJakub Kicinski
Periodically poll stats and call into offloaded actions to update them. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-21nfp: bpf: add hardware bpf offloadJakub Kicinski
Add hardware bpf offload on our smart NICs. Detect if capable firmware is loaded and use it to load the code JITed with just added translator onto programmable engines. This commit only supports offloading cls_bpf in legacy mode (non-direct action). Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-21nfp: add BPF to NFP code translatorJakub Kicinski
Add translator for JITing eBPF to operations which can be executed on NFP's programmable engines. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-16nfp: fix error return code in nfp_net_netdev_open()Wei Yongjun
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 73725d9dfd99 ("nfp: allocate ring SW structs dynamically") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-08nfp: don't pad frames on receiveJakub Kicinski
There is no need to pad frames to ETH_ZLEN on RX. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-08nfp: drop support for old firmware ABIsJakub Kicinski
Be more strict about FW versions. Drop support for old transitional revisions which were never used in production. Dropping support for FW ABI version 0.0.0.0 is particularly useful because 0 could just be uninitialized memory. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-08nfp: remove linux/version.h includesJakub Kicinski
Remove unnecessary version.h includes. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-11nfp: check idx is -ENOSPC before using it is an indexColin Ian King
idx can be returned as -ENOSPC, so we should check for this first before using it as an index into nn->vxlan_usecnt[] to avoid an out of bounds array offset read. Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-30nfp: implement ethtool .get_link() callbackJakub Kicinski
Point the ethtool .get_link() callback to the standard ethtool_op_get_link() implementation. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-30nfp: remove unused parameter from nfp_net_write_mac_addr()Jakub Kicinski
nfp_net_write_mac_addr() always writes to the BAR the current device address taken from netdev struct. The address given as parameter is actually ignored. Since all callers pass netdev->dev_addr simply remove the parameter. While at it improve the function's kdoc a bit. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-30nfp: correct name of control BAR defineJakub Kicinski
Spell abbreviation of control as ctrl not crtl. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Several cases of overlapping changes, except the packet scheduler conflicts which deal with the addition of the free list parameter to qdisc_enqueue(). Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-17nfp: Replace ndo_add/del_vxlan_port with ndo_add/del_udp_enc_portAlexander Duyck
This change replaces the network device operations for adding or removing a VXLAN port with operations that are more generically defined to be used for any UDP offload port but provide a type. As such by just adding a line to verify that the offload type is VXLAN we can maintain the same functionality. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-16nfp: use correct index to mask link state irqJakub Kicinski
We were using an incorrect define to get the irq vector number. NFP_NET_CFG_LSC is a control BAR offset, LSC interrupt vector index is called NFP_NET_IRQ_LSC_IDX. For machines with less than 30 CPUs this meant that we were disabling/enabling IRQ 0. For bigger hosts we were just playing with the 31st RX/TX interrupt. Fixes: 0ba40af963f0 ("nfp: move link state interrupt request/free calls") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-16nfp: add async reconfiguration mechanismJakub Kicinski
Some callers of nfp_net_reconfig() are in atomic context so we used to busy wait for commands to complete. In worst case scenario that means locking up a core for up to 5 seconds when a command times out. Lets add a timer-based mechanism of asynchronously checking whether reconfiguration completed successfully for atomic callers to use. Non-atomic callers can now just sleep. The approach taken is quite simple because (1) synchronous reconfigurations always happen under RTNL (or before device is registered); (2) we can coalesce pending reconfigs. There is no need for request queues, timer which eventually takes a look at reconfiguration result to report errors is good enough. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-16nfp: remove buggy RX buffer length validationJakub Kicinski
Meaning of data_len and meta_len RX WB descriptor fields is slightly confusing. Add a comment with a diagram clarifying the layout. Also remove the buffer length validation: (a) it's imprecise for static rx-offsets; (b) if firmware is buggy enough to DMA past the end of the buffer WARN_ON_ONCE() doesn't seem like a strong enough response. skb_put() will do the checking for us anyway. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-16nfp: remove unused suspicious mask definesJakub Kicinski
NFP_NET_RXR_MASK sounds like a mask which could be used on NFP_NET_CFG_RXRS_ENABLE register but its value is quite strange. In fact there are no users of this define so let's just remove it. Same for TX rings. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-16nfp: correct names of constants in commentsJakub Kicinski
Documentation in comments lacks CFG in some names. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-16nfp: remove unnecessary staticJakub Kicinski
There is no reason for those local variables to be static. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-16nfp: check the right pointer for errorsJakub Kicinski
Correct checking error condition on wrong pointer - copy/paste mistake most likely. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: allow ring size reconfiguration at runtimeJakub Kicinski
Since much of the required changes have already been made for changing MTU at runtime let's use it for ring size changes as well. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: pass ring count as function parameterJakub Kicinski
Soon ring resize will call this functions with values different than the current configuration we need to explicitly pass the ring count as parameter. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: convert .ndo_change_mtu() to prepare/commit paradigmJakub Kicinski
When changing MTU on running device first allocate new rings and buffers and once it succeeds proceed with changing MTU. Allocation of new rings is not really necessary for this operation - it's done to keep the code simple and because size of the extra ring memory is quite small compared to the size of buffers. Operation can still fail midway through if FW communication times out. In that case we retry with old MTU (rings). Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: propagate list buffer size in struct rx_ringJakub Kicinski
Free list buffer size needs to be propagated to few functions as a parameter and added to struct nfp_net_rx_ring since soon some of the functions will be reused to manage rings with buffers of size different than nn->fl_bufsz. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: sync ring state during FW reconfigurationJakub Kicinski
FW reconfiguration in .ndo_open()/.ndo_stop() should reset/ restore queue state. Since we need IRQs to be disabled when filling rings on RX path we have to move disable_irq() from .ndo_open() all the way up to IRQ allocation. nfp_net_start_vec() becomes trivial now so it's inlined. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: slice .ndo_open() and .ndo_stop() upJakub Kicinski
Divide .ndo_open() and .ndo_stop() into logical, callable chunks. No functional changes. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: move filling ring information to FW configJakub Kicinski
nfp_net_[rt]x_ring_{alloc,free} should only allocate or free ring resources without touching the device. Move setting parameters in the BAR to separate functions. This will make it possible to reuse alloc/free functions to allocate new rings while the device is running. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: preallocate RX buffers early in .ndo_openJakub Kicinski
We want the .ndo_open() to have following structure: - allocate resources; - configure HW/FW; - enable the device from stack perspective. Therefore filling RX rings needs to be moved to the beginning of .ndo_open(). Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: reorganize initial filling of RX ringsJakub Kicinski
Separate allocation of buffers from giving them to FW, thanks to this it will be possible to move allocation earlier on .ndo_open() path and reuse buffers during runtime reconfiguration. Similar to TX side clean up the spill of functionality from flush to freeing the ring. Unlike on TX side, RX ring reset does not free buffers from the ring. Ring reset means only that FW pointers are zeroed and buffers on the ring must be placed in [0, cnt - 1) positions. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: cleanup tx ring flush and rename to resetJakub Kicinski
Since we never used flush without freeing the ring later the functionality of the two operations is mixed. Rename flush to ring reset and move there all the things which have to be done after FW ring state is cleared. While at it do some clean-ups. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: allocate ring SW structs dynamicallyJakub Kicinski
To be able to switch rings more easily on config changes allocate them dynamically, separately from nfp_net structure. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: make *x_ring_init do all the initJakub Kicinski
nfp_net_[rt]x_ring_init functions used to be called from probe path only and some of their functionality was spilled to the call site. In order to reuse them for ring reconfiguration we need them to do all the init. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: break up nfp_net_{alloc|free}_ringsJakub Kicinski
nfp_net_{alloc|free}_rings contained strange mix of allocations and vector initialization. Remove it, declare vector init as a separate function and handle allocations explicitly. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: move link state interrupt request/free callsJakub Kicinski
We need to be able to disable the link state interrupt when the device is brought down. We used to just free the IRQ at the beginning of .ndo_stop(). As we now move towards more ordered .ndo_open()/.ndo_stop() paths LSC allocation should be placed in the "allocate resource" section. Since the IRQ can't be freed early in .ndo_stop(), it is disabled instead. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-08nfp: correct RX buffer length calculationJakub Kicinski
When calculating the RX buffer length we need to account for up to 2 VLAN tags. Rounding up to 1k is an relic of a distant past and can be removed. While at it also remove trivial print statement. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01asm-generic: remove old nonatomic-io wrapper filesArnd Bergmann
The two header files got moved to include/linux, and most users were already converted, this changes the remaining drivers and removes the files. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Vinod Koul <vinod.koul@intel.com> Acked-by: Simon Horman <simon.horman@netronome.com> Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
2015-12-18nfp: call netif_carrier_off() during initJakub Kicinski
Netdevs default to carrier on, we should call netif_carrier_off() during initialization since we handle carrier state changes in the driver. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Rolf Neugebauer <rolf.neugebauer@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-17nfp: clear ring delayed kick countersJakub Kicinski
We need to clear delayed kick counters when we free rings otherwise after ndo_close()/ndo_open() we could kick HW by more entries than actually written to rings. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Rolf Neugebauer <rolf.neugebauer@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15net: Rename NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASKTom Herbert
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the set of features for offloading all checksums. This is a mask of the checksum offload related features bits. It is incorrect to set both NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for features of a device. This patch: - Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where NETIF_F_ALL_CSUM is being used as a mask). - Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-03net: add driver for Netronome NFP4000/NFP6000 NIC VFsJakub Kicinski
Add driver for Virtual Functions for the Netronome's NFP-4000 and NFP-6000 based NICs. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Rolf Neugebauer <rolf.neugebauer@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-03 07:01:20 +0000