| Age | Commit message (Collapse) | Author |
|---|
|
We sometimes hit a "failed to flush" timeout on some TX queues, but the
flushes have completed and the flush completion events seem to go missing.
In this case, we can check the TX_DESC_PTR_TBL register and drain the
queues if the flushes had finished.
[bwh: Minor fixes to coding style]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Currently we initialise the newly allocated buffer to all-1s, which is
important for event queues but not for descriptor queues. And since
we also do that in efx_nic_init_eventq(), it is completely pointless
to do it here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
efx_writed_table() uses a step of 16 bytes but efx_readd_table() uses
a step of 4 bytes. Why are they different?
Firstly, register access is asymmetric:
- The EVQ_RPTR table and RX_INDIRECTION_TBL can (or must?) be written
as dwords even though they have a step size of 16 bytes, unlike
most other CSRs.
- In general, a read of any width is valid for registers, so long as
it does not cross register boundaries. There is also no latching
behaviour in the BIU, contrary to rumour.
We write to the EVQ_RPTR table with efx_writed_table() but never read
it back as it's write-only. We write to the RX_INDIRECTION_TBL with
efx_writed_table(), but only read it back for the register dump, where
we use efx_reado_table() as for any other table with step size of 16.
We read MC_TREG_SMEM with efx_readd_table() for the register dump, but
normally read and write it with efx_readd() and efx_writed() using
offsets calculated in bytes.
Since these functions are trivial and have few callers, it's clearer
to open-code them at the call sites. While we're at it, update the
comments on the BIU behaviour again.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Receiving pause frames can block TX queue flushes. Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
There are now standard functions for dealing with little-endian bit
arrays, so use them instead of our own implementations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
TSO header buffers contain a control structure immediately followed by
the packet headers, and are kept on a free list when not in use. This
complicates buffer management and tends to result in cache read misses
when we recycle such buffers (particularly if DMA-coherent memory
requires caches to be disabled).
Replace the free list with a simple mapping by descriptor index. We
know that there is always a payload descriptor between any two
descriptors with TSO header buffers, so we can allocate only one
such buffer for each two descriptors.
While we're at it, use a standard error code for allocation failure,
not -1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Add a flags field to struct efx_tx_buffer, replacing the
continuation and map_single booleans.
Since a single descriptor cannot be both a TSO header and the last
descriptor for an skb, unionise efx_tx_buffer::{skb,tsoh} and add
flags for validity of these fields.
Clear all flags in free buffers (whereas previously the continuation
flag would be set).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.
On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again. So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.
In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting. Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Generate a test event on each event queue whenever the interface is
brought up, then after 1 second check that we have either handled a
test event or handled another IRQ for each event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Cleanup in preparation for doing an event test on ifup.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
RX and TX completions on the same event queue are generally not associated
with the same flows. The inclusion of TX completions in the adaptive IRQ
score is more of a source of noise rather than useful feedback. Therefore,
do not include them in the score, and adjust the default threshold scores
down.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register. These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.
We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.
There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF. Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.
The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.
This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Each port has a block of 64-bit SRAM that is divided between buffer
table and descriptor cache regions at initialisation time. Currently
we use a fixed allocation, but it needs to be changed to support
larger numbers of queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The TX DMA engine issues upstream read requests when there is room in
the TX FIFO for the completion. However, the fetches for the rest of
the packet might be delayed by any back pressure. Since a flush must
wait for an EOP, the entire flush may be delayed by back pressure.
Mitigate this by disabling flow control before the flushes are
started. Since PF and VF flushes run in parallel introduce
fc_disable, a reference count of the number of flushes outstanding.
The same principle could be applied to Falcon, but that
would bring with it its own testing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
For SR-IOV we will need to send events to event queues that belong to
VFs serviced by other drivers. Change the parameters of
efx_generate_event() to allow this and declare it extern.
While we're at it, remove the existing declaration under the wrong
name efx_nic_generate_event().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
When SR-IOV is enabled we may receive FLR (Function-Level Reset)
events, associated queue flush events and requests from VF drivers at
any time. Therefore we need to keep event queues and interrupts
enabled whenever possible.
Currently we stop interrupt-driven event processing before flushing RX
and TX queues; efx_nic_flush_queues() then polls event queues for
flush events and discards any others it finds. Change it to work with
the regular event handling functions.
Currently efx_start_channel() fills RX queues synchronously when a
device is brought up. This could now race with NAPI, so change it to
send fill events.
This was almost entirely written by Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This makes it harder to accidentally send such events to TX-only
channels.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The 'page size' for PCIe DMA, i.e. the alignment of boundaries at
which DMA must be broken, is 4KB. Name this value as EFX_PAGE_SIZE
and use it in efx_max_tx_len(). Redefine EFX_BUF_SIZE as
EFX_PAGE_SIZE since its value is also a result of that requirement,
and use it in efx_init_special_buffer().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Replace checksummed and discard booleans from efx_handle_rx_event()
with a bitmask, added to the flags field.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The out-of-tree version of the sfc driver used to run a self-test on
each device before registering it. Although this was never included
in-tree, some functions have checks for this special case which is not
really possible.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Interrupts are normally generated by the event queues, moderated by
timers. However, they may also be triggered by detection of a 'fatal'
error condition (e.g. memory parity error) or by the host writing to
certain CSR fields as part of a self-test.
The IRQ level/index used for these on Falcon rev B0 and Siena is set
by the KER_INT_LEVE_SEL field and cached by the driver in
efx_nic::fatal_irq_level. Since this value is also relevant to
self-tests rename the field to just 'irq_level'.
Avoid unnecessary cache traffic by using a per-channel 'last_irq_cpu'
field and only writing to the per-controller field when the interrupt
matches efx_nic::irq_level. Remove the volatile qualifier and use
ACCESS_ONCE in the places we read these fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The netif_dbg() macro is defined in <linux/netdevice.h>. If the DEBUG
macro is defined, it logs a message at 'debug' level, otherwise it
does nothing.
In net_driver.h we define DEBUG if EFX_ENABLE_DEBUG is defined, but
this is too late for those source files that already got a
definition of netif_dbg() by including <linux/netdevice.h>
Get rid of EFX_ENABLE_DEBUG, and only define and test DEBUG.
In mtd.c, we do not use DEBUG as a condition flag but are forced to
use the DEBUG macro-function from <linux/mtd/mtd.h>. Undefine DEBUG
before including it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Fix the following errors and warnings:
ERROR: trailing whitespace
ERROR: spaces required around that '=' (ctx:VxV)
WARNING: please, no space before tabs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Conflicts:
MAINTAINERS
drivers/net/Kconfig
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
drivers/net/ethernet/broadcom/tg3.c
drivers/net/wireless/iwlwifi/iwl-pci.c
drivers/net/wireless/iwlwifi/iwl-trans-tx-pcie.c
drivers/net/wireless/rt2x00/rt2800usb.c
drivers/net/wireless/wl12xx/main.c
|
|
Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.
CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
