| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 51302f77bedab8768b761ed1899c08f89af9e4e2 ]
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes: 870915feabdc ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9737cc99dd14b5b8b9d267618a6061feade8ea68 ]
After flushing all mcast entries from the table, the ones contained in
mc list of ndev are not restored when promisc mode is toggled off,
because they are considered as synched with ALE, thus, in order to
restore them after promisc mode - reset syncing info. This fix
touches only switch mode devices, including single port boards
like Beagle Bone.
Fixes: commit 5da1948969bc
("net: ethernet: ti: cpsw: fix lost of mcast packets while rx_mode update")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5e5add172ea81152d518b161ec5706503ad3d799 ]
In dual_mac mode packets arrived on one port should not be forwarded by
switch hw to another port. Only Linux Host can forward packets between
ports. The below test case (reported in [1]) shows that packet arrived on
one port can be leaked to anoter (reproducible with dual port evms):
- connect port 1 (eth0) to linux Host 0 and run tcpdump or Wireshark
- connect port 2 (eth1) to linux Host 1 with vlan 1 configured
- ping <IPx> from Host 1 through vlan 1 interface.
ARP packets will be seen on Host 0.
Issue happens because dual_mac mode is implemnted using two vlans: 1 (Port
1+Port 0) and 2 (Port 2+Port 0), so there are vlan records created for for
each vlan. By default, the ALE will find valid vlan record in its table
when vlan 1 tagged packet arrived on Port 2 and so forwards packet to all
ports which are vlan 1 members (like Port.
To avoid such behaviorr the ALE VLAN ID Ingress Check need to be enabled
for each external CPSW port (ALE_PORTCTLn.VID_INGRESS_CHECK) so ALE will
drop ingress packets if Rx port is not VLAN member.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5e391dc5a8d801a2410d0032ad4a428d1d61800c ]
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b747 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 48f5bccc60675f8426a6159935e8636a1fd89f56 ]
When users set flow control using ethtool the bits are set properly in the
CPGMAC_SL MACCONTROL register, but the FIFO depth in the respective Port n
Maximum FIFO Blocks (Pn_MAX_BLKS) registers remains set to the minimum size
reset value. When receive flow control is enabled on a port, the port's
associated FIFO block allocation must be adjusted. The port RX allocation
must increase to accommodate the flow control runout. The TRM recommends
numbers of 5 or 6.
Hence, apply required Port FIFO configuration to
Pn_MAX_BLKS.Pn_TX_MAX_BLKS=0xF and Pn_MAX_BLKS.Pn_RX_MAX_BLKS=0x5 during
interface initialization.
Cc: Schuyler Patton <spatton@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
interface
[ Upstream commit f9db50691db4a7d860fce985f080bb3fc23a7ede ]
According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and
DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only
available when PHY is configured in RGMII mode with 10Mbps speed. It will
cause some networking issues without RGMII mode, such as carrier sense
errors and low throughput. TI also mentioned this issue in their forum[4].
This patch adds the check mechanism for PHY interface with RGMII interface
type, the in-band mode can only be set in RGMII mode with 10Mbps speed.
References:
[1]: https://www.ti.com/lit/ug/spruh73p/spruh73p.pdf
[2]: http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf
[3]: http://www.ti.com/lit/ug/spruic2b/spruic2b.pdf
[4]: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/640765/2392155
Suggested-by: Holsety Chen (陳憲輝) <Holsety.Chen@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a60ced990e309666915d21445e95347d12406694 ]
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f39939595a4d4540406bfc11f265b2036af6d
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
netif_set_real_num_tx/rx_queues() are required to be called with rtnl_lock
taken, otherwise ASSERT_RTNL() warning will be triggered - which happens
now during System resume from suspend:
cpsw_resume()
|- cpsw_ndo_open()
|- netif_set_real_num_tx/rx_queues()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_open() by rtnl_lock/unlock() calls.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: commit e05107e6b747 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helper to deregister fixed-link PHYs registered using
of_phy_register_fixed_link().
Convert the two drivers that care to deregister their fixed-link PHYs to
use the new helper, but note that most drivers currently fail to do so.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to propagate errors from of_phy_register_fixed_link() which
can fail with -EPROBE_DEFER.
Fixes: 1f71e8c96fc6 ("drivers: net: cpsw: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to check for allocation failures before dereferencing a
NULL-pointer during probe.
Fixes: 649a1688c960 ("net: ethernet: ti: cpsw: create common struct to
hold shared driver data")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister the primary device in case the secondary emac
fails to probe.
kernel BUG at /home/johan/work/omicron/src/linux/net/core/dev.c:7743!
...
[<c05b3dec>] (free_netdev) from [<c04fe6c0>] (cpsw_probe+0x9cc/0xe50)
[<c04fe6c0>] (cpsw_probe) from [<c047b28c>] (platform_drv_probe+0x5c/0xc0)
Fixes: d9ba8f9e6298 ("driver: net: ethernet: cpsw: dual emac interface
implementation")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop references taken and deregister devices registered
during probe on probe errors (including deferred probe) and driver
unbind.
Specifically, PHY of-node references were never released and fixed-link
PHY devices were never deregistered.
Fixes: 9e42f715264f ("drivers: net: cpsw: add phy-handle parsing")
Fixes: 1f71e8c96fc6 ("drivers: net: cpsw: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister all child devices also on probe errors to avoid
leaks and to fix probe deferral:
cpsw 4a100000.ethernet: omap_device: omap_device_enable() called from invalid state 1
cpsw 4a100000.ethernet: use pm_runtime_put_sync_suspend() in driver?
cpsw: probe of 4a100000.ethernet failed with error -22
Add generic helper to undo the effects of cpsw_probe_dt(), which will
also be used in a follow-on patch to fix further leaks that have been
introduced more recently.
Note that the platform device is now runtime-resumed before registering
any child devices in order to make sure that it is synchronously
suspended after having deregistered the children in the error path.
Fixes: 1fb19aa730e4 ("net: cpsw: Add parent<->child relation support
between cpsw and mdio")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by of_find_device_by_node() when
looking up an mdio device from a phy_id property during probe.
Fixes: 549985ee9c72 ("cpsw: simplify the setup of the register
pointers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to keep the platform device runtime-resumed throughout probe
to avoid accessing the CPSW registers in the error path (e.g. for
deferred probe) with clocks disabled:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0872d08
...
[<c04fabcc>] (cpsw_ale_control_set) from [<c04fb8b4>] (cpsw_ale_destroy+0x2c/0x44)
[<c04fb8b4>] (cpsw_ale_destroy) from [<c04fea58>] (cpsw_probe+0xbd0/0x10c4)
[<c04fea58>] (cpsw_probe) from [<c047b2a0>] (platform_drv_probe+0x5c/0xc0)
Fixes: df828598a755 ("netdev: driver: ethernet: Add TI CPSW driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from the cpsw_fill_rx_channels()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ce52c744574b ("net: ethernet: ti: cpsw: add ethtool channels support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These ops allow to control number of channels driver is allowed to
work with at cpdma level. The maximum number of channels is 8 for
rx and 8 for tx. In dual_emac mode the h/w channels are shared
between two interfaces and changing number on one interface changes
number of channels on another.
How many channels are supported and enabled:
$ ethtool -l ethX
Change number of channels (up to 8)
$ ethtool -L ethX rx 6 tx 6
Per-channel statistic:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
internals
Keep the driver internals in C file. Currently it's not required for
drivers to know rx or tx a channel is, except create function.
So correct "channel create" function, and use all channel struct
macroses only for internal use.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw h/w supports up to 8 tx and 8 rx channels. This patch adds
multi-queue support to the driver only, shaper configuration will
be added with separate patch series. Default shaper mode, as
before, priority mode, but with corrected priority order, 0 - is
highest priority, 7 - lowest.
The poll function handles all unprocessed channels, till all of
them are free, beginning from hi priority channel.
In dual_emac mode the channels are shared between two network devices,
as it's with single-queue default mode.
The statistic for every channel can be read with:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx channels share same pool of descriptors. Thus one channel can
block another if pool is emptied by one. But, the shaper should
decide which channel is allowed to send packets. To avoid such
impact of one channel on another, let every channel to have its
own piece of pool.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ale, cpts, version, rx_packet_max, bus_freq, interrupt pacing
parameters are common per net device that uses the same h/w. So,
move them to common driver structure.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The napi structs are common for both net devices in dual_emac
mode, In order to not hold duplicate links to them, move to
cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These data are common for net devs in dual_emac mode. No need to hold
it for every priv instance, so move them under cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The irq data are common for net devs in dual_emac mode. So no need to
hold these data in every priv struct, move them under cpsw_common.
Also delete irq_num var, as after optimization it's not needed.
Correct number of irqs to 2, as anyway, driver is using only 2,
at least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every net device private struct holds links to shared cpdma resources.
No need to save and every time synchronize these resources per net dev.
So, move it to common driver struct.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pointers on h/w registers are common for every cpsw_private
instance, so no need to hold them for every ndev.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to hold pdev link when only dev is needed.
This allows to simplify a bunch of cpsw->pdev->dev now and farther.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch simply create holder for common data and as a start moves
pdev var to it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to check const slave num in runtime for every packet,
and ndev for slaves w/o ndev is anyway NULL. So remove redundant
check and macro.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to hold link to clk, it's used only once
while probe.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need in priv here.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At poll handler no possibility to figure out which network device is
handling packets, as cpdma channels are common for both network
devices in dual_emac mode. Currently, the messages are printed only
for one device, in fact, there is two. This print msg is incorrect
and seems is not very useful, so drop it from poll handler.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As second net dev is created only in case of dual_emac mode, port
number can be figured out in simpler way. Also no need to pass
redundant ndev struct.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kmemleak reports following false positive memory leaks for each sk
buffers allocated by CPSW (__netdev_alloc_skb_ip_align()) in
cpsw_ndo_open() and cpsw_rx_handler():
unreferenced object 0xea915000 (size 2048):
comm "systemd-network", pid 713, jiffies 4294938323 (age 102.180s)
hex dump (first 32 bytes):
00 58 91 ea ff ff ff ff ff ff ff ff ff ff ff ff .X..............
ff ff ff ff ff ff fd 0f 00 00 00 00 00 00 00 00 ................
backtrace:
[<c0108680>] __kmalloc_track_caller+0x1a4/0x230
[<c0529eb4>] __alloc_skb+0x68/0x16c
[<c052c884>] __netdev_alloc_skb+0x40/0x104
[<bf1ad29c>] cpsw_ndo_open+0x374/0x670 [ti_cpsw]
[<c053c3d4>] __dev_open+0xb0/0x114
[<c053c690>] __dev_change_flags+0x9c/0x14c
[<c053c760>] dev_change_flags+0x20/0x50
[<c054bdcc>] do_setlink+0x2cc/0x78c
[<c054c358>] rtnl_setlink+0xcc/0x100
[<c054b34c>] rtnetlink_rcv_msg+0x184/0x224
[<c056467c>] netlink_rcv_skb+0xa8/0xc4
[<c054b1c0>] rtnetlink_rcv+0x2c/0x34
[<c0564018>] netlink_unicast+0x16c/0x1f8
[<c0564498>] netlink_sendmsg+0x334/0x348
[<c052015c>] sock_sendmsg+0x1c/0x2c
[<c05213e0>] SyS_sendto+0xc0/0xe8
unreferenced object 0xec861780 (size 192):
comm "softirq", pid 0, jiffies 4294938759 (age 109.540s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 b0 5a ed 00 00 00 00 00 00 00 00 ......Z.........
backtrace:
[<c0107830>] kmem_cache_alloc+0x190/0x208
[<c052c768>] __build_skb+0x30/0x98
[<c052c8fc>] __netdev_alloc_skb+0xb8/0x104
[<bf1abc54>] cpsw_rx_handler+0x68/0x1e4 [ti_cpsw]
[<bf11aa30>] __cpdma_chan_free+0xa8/0xc4 [davinci_cpdma]
[<bf11ab98>] __cpdma_chan_process+0x14c/0x16c [davinci_cpdma]
[<bf11abfc>] cpdma_chan_process+0x44/0x5c [davinci_cpdma]
[<bf1adc78>] cpsw_rx_poll+0x1c/0x9c [ti_cpsw]
[<c0539180>] net_rx_action+0x1f0/0x2ec
[<c003881c>] __do_softirq+0x134/0x258
[<c0038a00>] do_softirq+0x68/0x70
[<c0038adc>] __local_bh_enable_ip+0xd4/0xe8
[<c0640994>] _raw_spin_unlock_bh+0x30/0x34
[<c05f4e9c>] igmp6_group_added+0x4c/0x1bc
[<c05f6600>] ipv6_dev_mc_inc+0x398/0x434
[<c05dba74>] addrconf_dad_work+0x224/0x39c
This happens because CPSW allocates SK buffers and then passes
pointers on them in CPDMA where they stored in internal CPPI RAM
(SRAM) which belongs to DEV MMIO space. Kmemleak does not scan IO
memory and so reports memory leaks.
Hence, mark allocated sk buffers as false positive explicitly.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of_platform_depopulate() in cpsw_remove() instead of
of_device_unregister(), because CSPW child devices will not be
recreated otherwise on next insmod. of_platform_depopulate() is
correct way now as it will ensure that all steps done in
of_platform_populate() are reverted, including cleaning up of
OF_POPULATED flag.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L3 error will be generated and system will crash during unloading
of CPSW driver if CPSW is used as module and ethX devices are down.
This happens because CPSW can be power off by PM runtime now when ethX
devices are down.
Hence, ensure that CPSW powered up by PM runtime before performing any
deinitialization actions which require CPSW registers access. In case
of PM runtime error just leave cpsw_remove() as we can't do anything
anymore.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through net_device_ops interfce. In
this case net_device_ops operations requiring registers access will
cause L3 errors and CPSW crash.
Hence, fix it by adding RPM get/put calls in net_device_ops callbacks
which need to access CPSW registers: .ndo_set_mac_address(),
.ndo_vlan_rx_add_vid(), .ndo_vlan_rx_kill_vid().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through ethtool interfce. In this case
ethtool operations, requiring registers access, will cause L3 errors and
CPSW crash.
ethtool callbcaks which need to access CPSW registers now:
.set_coalesce(), .get_ethtool_stats(), .set_pauseparam(), .get_regs()
Hence, fix it by adding .begin()/.complete() ethtool callbacks, which
will be called before/after each ethtool operation runs, and do CPSW
RPM handling in these callbacks. That way CPSW will be active while
handling ethtool requests.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PM runtime is properly handled in cpsw_ndo_open/stop(), as result it
isn't required to duplicate these calls in .suspend()/.resume()
callbacks. Moreover, it might cause unnecessary RPM resume of CPSW
during System suspend in the case it's already suspended because
all ethX interfaces are down already, before System suspend started.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missed check of return code from PM runtime get() calls.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw_suspend() could trigger L3 error and CPSW will stop
functioning if System enters suspend when all ethX net-devices are
down - in this case CPSW could be already suspended by PM runtime, but
cpsw_suspend() will try to call soft_reset_slave() unconditionally
and access CPSW registers.
Hence, fix it by moving soft_reset_slave() from cpsw_suspend() to
cpsw_slave_stop(). This way slave ports will be reset when CPSW is
active and will be in proper state during Suspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dual MAC devices don't necessarily have both MACs wired up, so ignore
those that are disabled.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason in rx_descs property because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels.
That is, if number of descriptors 256, 128 of them are for rx
channels. While receiving, the descriptor is freed to the pool and
then allocated with new skb. And if in DT the "rx_descs" is set to
64, then 128 - 64 = 64 descriptors are always in the pool and cannot
be used, for tx, for instance. It's not correct resource usage,
better to set it to half of pool, then the rx pool can be used in
full. It will not have any impact on performance, as anyway, the
"redundant" descriptors were unused.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason to destroy channels that are destroyed while
cpdma_ctlr destroy. In this case no need to remember how much
channels where created and destroy them by one, as cpdma_ctlr
destroys all of them.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason in this lock. At least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rx-usecs shouldn't be changed while interface down/up.
Currently, for instance, if it's set to 100us, after interface
down/up it's 500us. It's a hidden bug that can lead to lavish
interrupt pacing time increasing while "down/up" up to max value.
Steps to reproduce:
- set rx-usecs to be 100us
- down/up interface
- read new unexpected rx-usecs
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
