| Age | Commit message (Collapse) | Author |
|---|
|
commit aec653c43b0c55667355e26d7de1236bda9fb4e3 upstream.
Call igb_setup_link() when the PHY is powered up.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 5f478b41033606d325e420df693162e2524c2b94 ]
mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.
Fixes: 71f6d1b31fb1 ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit aebea2ba0f7495e1a1c9ea5e753d146cb2f6b845 ]
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 2d5c57d7fbfaa642fb7f0673df24f32b83d9066c ]
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit a620a6bc1c94c22d6c312892be1e0ae171523125 ]
If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.
This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit d0aedcd4f14a22e23b313f42b7e6e6ebfc0fbc31 ]
vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.
The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.
Orabug: 19441666
OraBZ: 14983
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 9026968abe7ad102f4ac5c6d96d733643f75399c ]
This reverts commit 8ef29f8aae524bd51298fb10ac6a5ce6c4c5a3d8.
The driver core already calls pinctrl_get() and claims the default
state. There is no need to replicate this in the driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 7d3083ee36b51e425b6abd76778a2046906b0fd3 ]
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 476c18850c6cbaa3f2bb661ae9710645081563b9 ]
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 10545937e866ccdbb7ab583031dbdcc6b14e4eb4 ]
On IOMMU systems DMA mapping can fail, we need to check for
that possibility.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit cbd5228199d8be45d895d9d0cc2b8ce53835fc21 upstream.
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 68273712a19e9107a498a371532b3b3eb6dbb14c upstream.
This patch adds support for 57764, 57765, 57787, 57782 and 57786
devices.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit bd8e012b5d369933f50842294372ed580f5d9605 upstream.
Since commit 3fb43eb ("bnx2x: Change to D3hot only on removal") nvram
is accessible whenever the driver is loaded - Thus it is possible to
test it during self-test even if the interface is down
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 4710b2ba873692194c636811ceda398f95e02db2 upstream.
netxen_process_lro() contains two bounds checks. One for the ring number
against the number of rings, and one for the Rx buffer ID against the
array of receive buffers.
Both of these have off-by-one errors, using > instead of >=. The correct
versions are used in netxen_process_rcv(), they're just wrong in
netxen_process_lro().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 3e5480791e3b0e239d2cd4e5ecd43a7d2585484b upstream.
The fallback to 32-bit DMA mask is rather odd:
if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
!dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
*using_dac = true;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err)
goto release_regions;
}
This means we only try and set the coherent DMA mask if we failed to
set a 32-bit DMA mask, and only if both fail do we fail the driver.
Adjust this so that if either setting fails, we fail the driver - and
thereby end up properly setting both the DMA mask and the coherent
DMA mask in the fallback case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit de524681f88ff4ed293aa239f83c8cb04d59b47d upstream.
Add the missing iounmap() before return from igbvf_probe()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 3de9e65f011b95235a789b12abc4730570cdb737 upstream.
If new_mtu is very large then "new_mtu + ETH_HLEN + ETH_FCS_LEN" can
wrap and the check on the next line can underflow. This is one of those
bugs which can be triggered by the user if you have namespaces
configured.
Also since this is something the user can trigger then we don't want to
have dev_err() message.
This is a static checker fix and I'm not sure what the impact is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Sibai Li Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit c21b8ebc2f1613fd0a9d5aa0d0d1083aee8ca306 upstream.
The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev, "No usable DMA "
"configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 42ce4126d8bc2e128e1f207cf79bb0623fac498f upstream.
This patch fixes Wake on LAN being reported as supported on some Ethernet
ports, in contrary to Hardware capability.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit a71fc313c4f569be5788caff07ef1fe346842c5b upstream.
Don't let ethtool try to write to iNVM in i210/i211.
This fixes an issue seen by Marek Vasut.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 781798a11e2820ee35fa9142869bb8cec117dedc upstream.
commit fa44f2f185f7f9da19d331929bb1b56c1ccd1d93 broke reloading of igb, when
VFs are assigned to a guest, in several ways.
1. on module load adapter->vf_data does not get properly allocated,
resulting in a null pointer exception when accessing adapter->vf_data in
igb_reset() on module reload.
modprobe -r igb ; modprobe igb max_vfs=7
[ 215.215837] igb 0000:01:00.1: removed PHC on eth1
[ 216.932072] igb 0000:01:00.1: IOV Disabled
[ 216.937038] igb 0000:01:00.0: removed PHC on eth0
[ 217.127032] igb 0000:01:00.0: Cannot deallocate SR-IOV virtual functions while they are assigned - VFs will not be deallocated
[ 217.146178] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.5-k
[ 217.154050] igb: Copyright (c) 2007-2013 Intel Corporation.
[ 217.160688] igb 0000:01:00.0: Enabling SR-IOV VFs using the module parameter is deprecated - please use the pci sysfs interface.
[ 217.173703] igb 0000:01:00.0: irq 103 for MSI/MSI-X
[ 217.179227] igb 0000:01:00.0: irq 104 for MSI/MSI-X
[ 217.184735] igb 0000:01:00.0: irq 105 for MSI/MSI-X
[ 217.220082] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[ 217.228846] IP: [<ffffffffa007c5e5>] igb_reset+0xc5/0x4b0 [igb]
[ 217.235472] PGD 3607ec067 PUD 36170b067 PMD 0
[ 217.240461] Oops: 0002 [#1] SMP
[ 217.244085] Modules linked in: igb(+) igbvf mptsas mptscsih mptbase scsi_transport_sas [last unloaded: igb]
[ 217.255040] CPU: 4 PID: 4833 Comm: modprobe Not tainted 3.11.0+ #46
[...]
[ 217.390007] [<ffffffffa007fab2>] igb_probe+0x892/0xfd0 [igb]
[ 217.396422] [<ffffffff81470b3e>] local_pci_probe+0x1e/0x40
[ 217.402641] [<ffffffff81472029>] pci_device_probe+0xf9/0x110
[...]
2. A follow up issue, pci_enable_sriov() should only be called if no VFs were
still allocated on module unload. Otherwise pci_enable_sriov() gets called
multiple times in a row rendering the NIC unusable until reset.
3. simply calling igb_enable_sriov() in igb_probe_vfs() is not enough as the
interrupts need to be re-setup. Switching that to igb_pci_enable_sriov().
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit d1c17d806b6a52ff020322bec457717a91ea50a9 upstream.
This patch calls code to set the master/slave mode for all m88 gen 2
PHY's. This patch also removes the call to this function for I210 devices
only from the function that is not called by I210 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit a4e979a27db3eb77e286dbe484e96c0c9c986e83 upstream.
Add the ethtool offline tests for i354 devices.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit dc4ff9bb7534ebd153f8441ec0e9190964ad8944 upstream.
The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit c7bb417dbb8888cfd20824d54f9af9c92b9ff43d upstream.
Since we are already checking for read failure in check_link we don't need
to do it here. Instead just make sure the watchdog task gets scheduled, if
we are up, and it can be done there. This will better follow igbvf method
of handling a mailbox event and message timeout.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 53567aa4e00399aa59339bba81b285a5b95f425c upstream.
The fallback to 32-bit DMA mask is rather odd:
if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
!dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev, "No usable DMA "
"configuration, aborting\n");
goto err_dma;
}
}
pci_using_dac = 0;
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit cf78959c0d7afbde31498afc4212294c28e2c278 upstream.
This patch resolves an issue where the MTA table can be cleared when the
interface is reset while in promisc mode. As result IPv6 traffic between
VFs will be interrupted.
This patch makes the update of the MTA table unconditional to avoid the
inconsistent clearing on reset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 27d9ce4fd0e2e75c2907f6d3dc0487012a3e4298 upstream.
ixgbe_napi_disable_all calls napi_disable on each queue, however the busy
polling code introduced a local_bh_disable()d context around the napi_disable.
The original author did not realize that napi_disable might sleep, which would
cause a sleep while atomic BUG. In addition, on a single processor system, the
ixgbe_qv_lock_napi loop shouldn't have to mdelay. This patch adds an
ixgbe_qv_disable along with a new IXGBE_QV_STATE_DISABLED bit, which it uses to
indicate to the poll and napi routines that the q_vector has been disabled. Now
the ixgbe_napi_disable_all function will wait until all pending work has been
finished and prevent any future work from being started.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: Alexander Duyck <alexander.duyck@intel.com>
Cc: Hyong-Youb Kim <hykim@myri.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 2e0103810c6fed6a736c4a3af87b0f5c6bd8cd5b upstream.
This patch resolves an issue where the logic used to detect changes in rx-usecs
was incorrect and was masked by the call to ixgbe_update_rsc().
Setting rx-usecs between 0,2-9 and 1,10 and up requires a reset to allow
ixgbe_configure_tx_ring() to set the correct value for TXDCTL.WTHRESH in
order to avoid Tx hangs with BQL enabled.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit f5f2eda8049644a27af5fdf59c3766589358e435 upstream.
The fallback to 32-bit DMA mask is rather odd:
if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
!dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
pci_using_dac = 0;
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 74a1b1ea8a30b035aaad833bbd6b9263e72acfac upstream.
On e1000_down(), we should ensure every asynchronous work is canceled
before proceeding. Since the watchdog_task can schedule other works
apart from itself, it should be stopped first, but currently it is
stopped after the reset_task. This can result in the following race
leading to the reset_task running after the module unload:
e1000_down_and_stop(): e1000_watchdog():
---------------------- -----------------
cancel_work_sync(reset_task)
schedule_work(reset_task)
cancel_delayed_work_sync(watchdog_task)
The patch moves cancel_delayed_work_sync(watchdog_task) at the beginning
of e1000_down_and_stop() thus ensuring the race is impossible.
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 6a7d64e3e09e11181a07a2e8cd6af5d6355133be upstream.
This change is based on a similar change made to e1000e support in
commit bb9e44d0d0f4 ("e1000e: prevent oops when adapter is being closed
and reset simultaneously"). The same issue has also been observed
on the older e1000 cards.
Here, we have increased the RESET_COUNT value to 50 because there are too
many accesses to e1000 nic on stress tests to e1000 nic, it is not enough
to set RESET_COUT 25. Experimentation has shown that it is enough to set
RESET_COUNT 50.
Signed-off-by: yzhu1 <yanjun.zhu@windriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 49a45a0686cc2b43bcb3834a68416a201475dc77 upstream.
tx_ring and adapter->tx_ring are already of type "struct
e1000_tx_ring *"
Signed-off-by: Hong Zhiguo <zhiguohong@tencent.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 38a529b5d42e4cfc5ac94844e61335a00eb2d320 upstream.
Commit 7509963c703b (e1000e: Fix a compile flag mis-match for
suspend/resume) moved suspend and resume hooks to be available when
CONFIG_PM is set. However, it can be set even if CONFIG_PM_SLEEP is not set
causing following warnings to be emitted:
drivers/net/ethernet/intel/e1000e/netdev.c:6178:12: warning:
‘e1000_suspend’ defined but not used [-Wunused-function]
drivers/net/ethernet/intel/e1000e/netdev.c:6185:12: warning:
‘e1000_resume’ defined but not used [-Wunused-function]
To fix this make the hooks to be available only when CONFIG_PM_SLEEP is set
and remove CONFIG_PM wrapping from driver ops because this is already
handled by SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Aaron Brown <aaron.f.brown@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 7509963c703b71eebccc421585e7f48ebbbd3f38 upstream.
This patch addresses a mis-match between the declaration and usage of
the e1000_suspend and e1000_resume functions. Previously, these
functions were declared in a CONFIG_PM_SLEEP wrapper, and then utilized
within a CONFIG_PM wrapper. Both the declaration and usage will now be
contained within CONFIG_PM wrappers.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 718a39eb587e038f7ded076afcfd8d709879139f upstream.
The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit fe26566d8a05151ba1dce75081f6270f73ec4ae1 ]
When TSO packet is transmitted additional BD w/o mapping is used
to describe the packed. The BD needs special handling in tx
completion.
kernel: Call Trace:
kernel: <IRQ> [<ffffffff815e19ba>] dump_stack+0x19/0x1b
kernel: [<ffffffff8105dee1>] warn_slowpath_common+0x61/0x80
kernel: [<ffffffff8105df5c>] warn_slowpath_fmt+0x5c/0x80
kernel: [<ffffffff814a8c0d>] ? find_iova+0x4d/0x90
kernel: [<ffffffff814ab0e2>] intel_unmap_page.part.36+0x142/0x160
kernel: [<ffffffff814ad0e6>] intel_unmap_page+0x26/0x30
kernel: [<ffffffffa01f55d7>] bnx2x_free_tx_pkt+0x157/0x2b0 [bnx2x]
kernel: [<ffffffffa01f8dac>] bnx2x_tx_int+0xac/0x220 [bnx2x]
kernel: [<ffffffff8101a0d9>] ? read_tsc+0x9/0x20
kernel: [<ffffffffa01f8fdb>] bnx2x_poll+0xbb/0x3c0 [bnx2x]
kernel: [<ffffffff814d041a>] net_rx_action+0x15a/0x250
kernel: [<ffffffff81067047>] __do_softirq+0xf7/0x290
kernel: [<ffffffff815f3a5c>] call_softirq+0x1c/0x30
kernel: [<ffffffff81014d25>] do_softirq+0x55/0x90
kernel: [<ffffffff810673e5>] irq_exit+0x115/0x120
kernel: [<ffffffff815f4358>] do_IRQ+0x58/0xf0
kernel: [<ffffffff815e94ad>] common_interrupt+0x6d/0x6d
kernel: <EOI> [<ffffffff810bbff7>] ? clockevents_notify+0x127/0x140
kernel: [<ffffffff814834df>] ? cpuidle_enter_state+0x4f/0xc0
kernel: [<ffffffff81483615>] cpuidle_idle_call+0xc5/0x200
kernel: [<ffffffff8101bc7e>] arch_cpu_idle+0xe/0x30
kernel: [<ffffffff810b4725>] cpu_startup_entry+0xf5/0x290
kernel: [<ffffffff815cfee1>] start_secondary+0x265/0x27b
kernel: ---[ end trace 11aa7726f18d7e80 ]---
Fixes: a848ade408b ("bnx2x: add CSUM and TSO support for encapsulation protocols")
Reported-by: Yulong Pei <ypei@redhat.com>
Cc: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit a4b70a07ed12a71131cab7adce2ce91c71b37060 ]
Nothing cleans up the objects created by
vnet_new(), they are completely leaked.
vnet_exit(), after doing the vio_unregister_driver() to clean
up ports, should call a helper function that iterates over vnet_list
and cleans up those objects. This includes unregister_netdevice()
as well as free_netdev().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Reviewed-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 4cad9f3b61c7268fa89ab8096e23202300399b5d ]
On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 4d12bc63ab5e48c1d78fa13883cf6fefcea3afb1 ]
As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.
This problem exists since c5aff18204da0 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff18204da0 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 07b0f00964def8af9321cfd6c4a7e84f6362f728 ]
While it is legal to kfree(NULL), it is not wise to use :
put_page(virt_to_head_page(NULL))
BUG: unable to handle kernel paging request at ffffeba400000000
IP: [<ffffffffc01f5928>] virt_to_head_page+0x36/0x44 [bnx2x]
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Fixes: d46d132cc021 ("bnx2x: use netdev_alloc_frag()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 96dee024ca4799d6d21588951240035c21ba1c67 upstream.
Previous commit c3a0dce35af0 fixed an overrun for the RAR on i218 devices.
This commit also attempted to homogenize the RAR/SHRA access for all parts
accessed by the e1000e driver. This change introduced an error for
assigning MAC addresses to guest OS's for 82579 devices.
Only RAR[0] is accessible to the driver for 82579 parts, and additional
addresses must be placed into the SHRA[L|H] registers. The rar_entry_count
was changed in the previous commit to an inaccurate value that accounted
for all RAR and SHRA registers, not just the ones usable by the driver.
This patch fixes the count to the correct value and adjusts the
e1000_rar_set_pch2lan() function to user the correct index.
Cc: John Greene <jogreene@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "Alexander Y. Fomichev" <aleksandr.fomichev@x5.ru>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 76252723e88681628a3dbb9c09c963e095476f73 upstream.
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 948264879b6894dc389a44b99fae4f0b72932619 upstream.
On some devices, the internal PLL circuit occasionally provides the
wrong clock frequency after power up. The probability of failure is less
than one failure per 1000 power cycles. When the failure occurs, the
internal clock frequency is around 1/20 of the correct frequency.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit b91113282bf44df46aba374a0b8f88a75bfd4b3f upstream.
If the mdio probe function fails in emac_open, the interrupt we just requested
isn't freed. If emac_open is called again, for example because we try to set up
the interface again, the kernel will oops because the interrupt wasn't properly
released.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 6954cc1f238199e971ec905c5cc87120806ac981 upstream.
Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit d8b0426af5b67973585712c9af36b86f6ea97815 ]
Commit 4a55530f38e4 (net: sh_eth: modify the definitions of register) managed
to leave out the E-DMAC register entries in sh_eth_offset_fast_sh3_sh2[], thus
totally breaking SH7619/771x support. Add the missing entries using the data
from before that commit.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 530aa2d0d9d55ab2775d47621ddf4b5b15bc1110 ]
The current behaviour of the sh_eth driver is not to use the RNC bit
for the receive ring. This means that every packet recieved is not only
generating an IRQ but it also stops the receive ring DMA as well until
the driver re-enables it after unloading the packet.
This means that a number of the following errors are generated due to
the receive packet FIFO overflowing due to nowhere to put packets:
net eth0: Receive FIFO Overflow
Since feedback from Yoshihiro Shimoda shows that every supported LSI
for this driver should have the bit enabled it seems the best way is
to remove the RMCR default value from the per-system data and just
write it when initialising the RMCR value. This is discussed in
the message (http://www.spinics.net/lists/netdev/msg284912.html).
I have tested the 0x00000001 configuration with NFS root filesystem and
the driver has not failed yet. There are further test reports from
Sergei Shtylov and others for both the R8A7790 and R8A7791.
There is also feedback fron Cao Minh Hiep[1] which reports the
same issue in (http://comments.gmane.org/gmane.linux.network/316285)
showing this fixes issues with losing UDP datagrams under iperf.
Tested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 7df566bbdd0af0785542b89466a937e94257fcfb ]
This function is called from dcbnl_build_peer_app(). The "info"
struct isn't initialized at all so we disclose 2 bytes of uninitialized
stack data. We should clear it before passing it to the user.
Fixes: 48365e485275 ('qlcnic: dcb: Add support for CEE Netlink interface.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 1c3639005f48492e5f2d965779efd814e80f8b15 ]
If the sfc driver is in legacy interrupt mode (either explicitly by
using interrupt_mode module param or by falling back to it) it will
hit a warning at kernel/irq/manage.c because it will try to free an irq
which wasn't allocated by it in the first place because the MSI(X) irqs are
zero and it'll try to free them unconditionally. So fix it by checking if
we're in legacy mode and freeing the appropriate irqs.
CC: Zenghui Shi <zshi@redhat.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: David S. Miller <davem@davemloft.net>
Fixes: 1899c111a535 ("sfc: Fix IRQ cleanup in case of a probe failure")
Reported-by: Zenghui Shi <zshi@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
