summaryrefslogtreecommitdiff
path: root/drivers/net/usb
AgeCommit message (Collapse)Author
2014-10-31r8152: stop submitting intr for -EPROTOhayeswang
For Renesas USB 3.0 host controller, when unplugging the usb hub which has the RTL8153 plugged, the driver would get -EPROTO for interrupt transfer. There is high probability to get the information of "HC died; cleaning up", if the driver continues to submit the interrupt transfer before the disconnect() is called. [ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71 [ 1024.383097] usb 9-1: USB disconnect, device number 2 [ 1024.383103] usb 9-1.4: USB disconnect, device number 6 [ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command. [ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host. [ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up [ 1029.421480] usb 8-1: USB disconnect, device number 2 Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30r8152: check WORK_ENABLE in suspend functionhayeswang
Avoid unnecessary behavior when autosuspend occurs during open(). The relative processes should only be run after finishing open(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30r8152: reset tp->speed before autoresuming in open functionhayeswang
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume() would call rtl_start_rx() before enabling the tx/rx. Avoid this by resetting it to zero. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30r8152: clear SELECTIVE_SUSPEND when autoresuminghayeswang
The flag of SELECTIVE_SUSPEND should be cleared when autoresuming. Otherwise, when the system suspend and resume occur, it may have the wrong flow. Besides, because the flag of SELECTIVE_SUSPEND couldn't be used to check if the hw enables the relative feature, it should alwayes be disabled in close(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-28cdc-ether: handle promiscuous mode with a set_rx_mode callbackOlivier Blin
Promiscuous mode was not supported anymore with my Lenovo adapters (RTL8153) since commit c472ab68ad67db23c9907a27649b7dc0899b61f9 (cdc-ether: clean packet filter upon probe). It was not possible to use them in a bridge anymore. Signed-off-by: Olivier Blin <olivier.blin@softathome.com> Also-analyzed-by: Loïc Yhuel <loic.yhuel@softathome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-28cdc-ether: extract usbnet_cdc_update_filter functionOlivier Blin
This will be used by the set_rx_mode callback. Also move a comment about multicast filtering in this new function. Signed-off-by: Olivier Blin <olivier.blin@softathome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-28usbnet: add a callback for set_rx_modeOlivier Blin
To delegate promiscuous mode and multicast filtering to the subdriver. Signed-off-by: Olivier Blin <olivier.blin@softathome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-20ax88179_178a: fix bonding failureIan Morgan
The following patch fixes a bug which causes the ax88179_178a driver to be incapable of being added to a bond. When I brought up the issue with the bonding maintainers, they indicated that the real problem was with the NIC driver which must return zero for success (of setting the MAC address). I see that several other NIC drivers follow that pattern by either simply always returing zero, or by passing through a negative (error) result while rewriting any positive return code to zero. With that same philisophy applied to the ax88179_178a driver, it allows it to work correctly with the bonding driver. I believe this is suitable for queuing in -stable, as it's a small, simple, and obvious fix that corrects a defect with no other known workaround. This patch is against vanilla 3.17(.0). Signed-off-by: Ian Morgan <imorgan@primordial.ca> drivers/net/usb/ax88179_178a.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-17r8152: return -EBUSY for runtime suspendhayeswang
Remove calling cancel_delayed_work_sync() for runtime suspend, because it would cause dead lock. Instead, return -EBUSY to avoid the device enters suspending if the net is running and the delayed work is pending or running. The delayed work would try to wake up the device later, so the suspending is not necessary. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-09r8152: add mutex for hw settingshayeswang
Use the mutex to avoid the settings are interrupted by other ones. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-09r8152: adjust usb_autopm_xxxhayeswang
Add usb_autopm_xxx for rtl8152_get_settings() ,and remove usb_autopm_xxx from read_mii_word() and write_mii_word(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-09r8152: autoresume before setting featurehayeswang
Resume the device before setting the feature. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: "Most notable changes in here: 1) By far the biggest accomplishment, thanks to a large range of contributors, is the addition of multi-send for transmit. This is the result of discussions back in Chicago, and the hard work of several individuals. Now, when the ->ndo_start_xmit() method of a driver sees skb->xmit_more as true, it can choose to defer the doorbell telling the driver to start processing the new TX queue entires. skb->xmit_more means that the generic networking is guaranteed to call the driver immediately with another SKB to send. There is logic added to the qdisc layer to dequeue multiple packets at a time, and the handling mis-predicted offloads in software is now done with no locks held. Finally, pktgen is extended to have a "burst" parameter that can be used to test a multi-send implementation. Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4, virtio_net Adding support is almost trivial, so export more drivers to support this optimization soon. I want to thank, in no particular or implied order, Jesper Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann, David Tat, Hannes Frederic Sowa, and Rusty Russell. 2) PTP and timestamping support in bnx2x, from Michal Kalderon. 3) Allow adjusting the rx_copybreak threshold for a driver via ethtool, and add rx_copybreak support to enic driver. From Govindarajulu Varadarajan. 4) Significant enhancements to the generic PHY layer and the bcm7xxx driver in particular (EEE support, auto power down, etc.) from Florian Fainelli. 5) Allow raw buffers to be used for flow dissection, allowing drivers to determine the optimal "linear pull" size for devices that DMA into pools of pages. The objective is to get exactly the necessary amount of headers into the linear SKB area pre-pulled, but no more. The new interface drivers use is eth_get_headlen(). From WANG Cong, with driver conversions (several had their own by-hand duplicated implementations) by Alexander Duyck and Eric Dumazet. 6) Support checksumming more smoothly and efficiently for encapsulations, and add "foo over UDP" facility. From Tom Herbert. 7) Add Broadcom SF2 switch driver to DSA layer, from Florian Fainelli. 8) eBPF now can load programs via a system call and has an extensive testsuite. Alexei Starovoitov and Daniel Borkmann. 9) Major overhaul of the packet scheduler to use RCU in several major areas such as the classifiers and rate estimators. From John Fastabend. 10) Add driver for Intel FM10000 Ethernet Switch, from Alexander Duyck. 11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric Dumazet. 12) Add Datacenter TCP congestion control algorithm support, From Florian Westphal. 13) Reorganize sk_buff so that __copy_skb_header() is significantly faster. From Eric Dumazet" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits) netlabel: directly return netlbl_unlabel_genl_init() net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers net: description of dma_cookie cause make xmldocs warning cxgb4: clean up a type issue cxgb4: potential shift wrapping bug i40e: skb->xmit_more support net: fs_enet: Add NAPI TX net: fs_enet: Remove non NAPI RX r8169:add support for RTL8168EP net_sched: copy exts->type in tcf_exts_change() wimax: convert printk to pr_foo() af_unix: remove 0 assignment on static ipv6: Do not warn for informational ICMP messages, regardless of type. Update Intel Ethernet Driver maintainers list bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING tipc: fix bug in multicast congestion handling net: better IFF_XMIT_DST_RELEASE support net/mlx4_en: remove NETDEV_TX_BUSY 3c59x: fix bad split of cpu_to_le32(pci_map_single()) net: bcmgenet: fix Tx ring priority programming ...
2014-10-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2014-10-08Merge tag 'usb-3.18-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB updates from Greg KH: "Here's the big USB patchset for 3.18-rc1. Also in here is the PHY tree, as it seems to fit well with the USB tree for various reasons... Anyway, lots of little changes in here, all over the place, full details in the changelog All have been in the linux-next tree for a while with no issues" * tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits) USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST' uas: Reduce number of function arguments for uas_alloc_foo functions xhci: Allow xHCI drivers to be built as separate modules xhci: Export symbols used by host-controller drivers xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold xhci: Introduce xhci_init_driver() usb: hcd: add generic PHY support usb: rename phy to usb_phy in HCD usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo USB: host: st: fix ehci/ohci driver selection usb: host: ehci-exynos: Remove unnecessary usb-phy support usb: core: return -ENOTSUPP for all targeted hosts USB: Remove .owner field for driver usb: core: log higher level message on malformed LANGID descriptor usb: Add LED triggers for USB activity usb: Rename usb-common.c usb: gadget: Refactor request completion usb: gadget: Introduce usb_gadget_giveback_request() usb: dwc2/gadget: move phy bus legth initialization phy: remove .owner field for drivers using module_platform_driver ...
2014-10-06r8152: nway reset after setting eeehayeswang
Restart autonegotiation is necessary after setting EEE. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-03r8152: autoresume before setting MAC addresshayeswang
Resume the device before setting the MAC address. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-03asix: Don't reset PHY on if_up for ASIX 88772Michel Stam
I've noticed every time the interface is set to 'up,', the kernel reports that the link speed is set to 100 Mbps/Full Duplex, even when ethtool is used to set autonegotiation to 'off', half duplex, 10 Mbps. It can be tested by: ifconfig eth0 down ethtool -s eth0 autoneg off speed 10 duplex half ifconfig eth0 up Then checking 'dmesg' for the link speed. Signed-off-by: Michel Stam <m.stam@fugro.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/usb/r8152.c net/netfilter/nfnetlink.c Both r8152 and nfnetlink conflicts were simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-01r8152: disable power cut for RTL8153hayeswang
The firmware would be clear when the power cut is enabled for RTL8153. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-01r8152: remove clearing bphayeswang
The xxx_clear_bp() is used to halt the firmware. It only necessary for updating the new firmware. Besides, depend on the version of the current firmware, it may have problem to halt the firmware directly. Finally, halt the firmware would let the firmware code useless, and the bugs which are fixed by the firmware would occur. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-30r8152: fix setting RTL8152_UNPLUGhayeswang
The flag of RTL8152_UNPLUG should only be set when the device is unplugged, not each time the rtl8152_disconnect() is called. Otherwise, the device wouldn't be stopped normally. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-28r8152: support ethtool eeehayeswang
Support get_eee() and set_eee() of ethtool_ops. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-28r8152: add functions to set EEEhayeswang
Add functions to enable EEE and set EEE advertisement. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-28r8152: change the EEE definitionhayeswang
Replace the EEE definitions with the ones which is declared in "mdio.h". Chage some definitions to make them readable. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-26r8152: fix the carrier off when autoresuminghayeswang
netif_carrier_off would be called when autoresuming, even though the cable is plugged. This causes some applications do relative actions when detecting the carrier off. Keep the status of the carrier, and let it be modified when the linking change occurs. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-25Merge tag 'phy-for_3.18' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next Kishon writes: Adds 3 new PHY drivers stih407, stih41x and rcar gen2 PHY. It also includes miscellaneous cleanup of other PHY drivers. Conflicts: MAINTAINERS
2014-09-23usb: hub: rename khubd to hub_wq in documentation and commentsPetr Mladek
USB hub has started to use a workqueue instead of kthread. Let's update the documentation and comments here and there. This patch mostly just replaces "khubd" with "hub_wq". There are only few exceptions where the whole sentence was updated. These more complicated changes can be found in the following files: Documentation/usb/hotplug.txt drivers/net/usb/usbnet.c drivers/usb/core/hcd.c drivers/usb/host/ohci-hcd.c drivers/usb/host/xhci.c Signed-off-by: Petr Mladek <pmladek@suse.cz> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: arch/mips/net/bpf_jit.c drivers/net/can/flexcan.c Both the flexcan and MIPS bpf_jit conflicts were cases of simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-22r8152: disable ALDPShayeswang
If the hw is in ALDPS mode, the hw may have no response for accessing the most registers. Therefore, the ALDPS should be disabled before accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(), and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw wouldn't enter ALDPS mode when linking on. The hw would enter the ALDPS mode after several seconds when link down occurs and the ALDPS is enabled. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13r8152: support VLANhayeswang
Support hw VLAN for tx and rx. And enable them by default. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-09r8152: use usleep_rangehayeswang
Replace mdelay with usleep_range to avoid busy loop. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-05r8152: use eth_hw_addr_randomhayeswang
If the hw doesn't have a valid MAC address, give a random one and set it to the hw. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-05r8152: change the location of rtl8152_set_mac_addresshayeswang
Exchange the location of rtl8152_set_mac_address() and set_ethernet_addr(). Then, the set_ethernet_addr() could set the MAC address by calling rtl8152_set_mac_address() later. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01r8152: rename rx_buf_szhayeswang
The variable "rx_buf_sz" is used by both tx and rx buffers. Replace it with "agg_buf_sz". Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01r8152: reduce the number of Txhayeswang
Because the Tx has the features of stopping queue and aggregation, We don't need many tx buffers. Change the tx number from 10 to 4 to reduce the usage of the memory. This could save 16K * 6 bytes memory. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-27r8152: replace strncpy with strlcpyhayeswang
Replace the strncpy with strlcpy, and use sizeof to determine the length. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-25r8152: check code with checkpatch.plhayeswang
626: CHECK: Alignment should match open parenthesis 646: CHECK: Alignment should match open parenthesis 655: CHECK: Alignment should match open parenthesis 695: CHECK: Alignment should match open parenthesis 729: CHECK: Alignment should match open parenthesis 739: CHECK: Alignment should match open parenthesis 976: WARNING: externs should be avoided in .c files 1314: CHECK: Alignment should match open parenthesis 1358: WARNING: networking block comments don't use an empty /* line, use /* Comment... 1402: WARNING: networking block comments don't use an empty /* line, use /* Comment... 1521: CHECK: multiple assignments should be avoided 1775: CHECK: Alignment should match open parenthesis 1838: CHECK: multiple assignments should be avoided 1843: CHECK: multiple assignments should be avoided 1847: CHECK: multiple assignments should be avoided 1850: WARNING: Missing a blank line after declarations 1864: CHECK: Alignment should match open parenthesis 1872: CHECK: braces {} should be used on all arms of this statement 1906: CHECK: usleep_range is preferred over udelay 2865: WARNING: networking block comments don't use an empty /* line, use /* Comment... 3088: CHECK: Alignment should match open parenthesis total: 0 errors, 5 warnings, 16 checks, 3567 lines checked Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-06net: fix USB network driver config option.Francois Romieu
It must be tristate to avoid broken dependencies with kernel built-in usb network drivers when usb support is module only. When net config option is set, least surprize default should match usb. Wireless RNDIS USB driver used to select USB_USBNET. USB_USBNET now depends on USB_NET_DRIVERS so the latter should be selected as well. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/Makefile net/ipv6/sysctl_net_ipv6.c Two ipv6_table_template[] additions overlap, so the index of the ipv6_table[x] assignments needed to be adjusted. In the drivers/net/Makefile case, we've gotten rid of the garbage whereby we had to list every single USB networking driver in the top-level Makefile, there is just one "USB_NETWORKING" that guards everything. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-05net: reduce USB network driver config options.Francois Romieu
USB network drivers are already handled in drivers/net/usb/Kconfig. Let's save the maintenance burden of dependencies in drivers/net/Makefile. The newly introduced USB_NET_DRIVERS umbrella config option defaults to 'y' so as to minimize the changes of behavior. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-05net/usb/hso: Add support for Option GTM671WFSRicardo Ribalda
After this patch: [ 32.985530] hso: drivers/net/usb/hso.c: Option Wireless [ 33.000452] hso 2-1.4:1.7: Not our interface [ 33.001849] usbcore: registered new interface driver hso root@qt5022:~# ls /dev/ttyHS* /dev/ttyHS0 /dev/ttyHS1 /dev/ttyHS2 /dev/ttyHS3 /dev/ttyHS4 /dev/ttyHS5 root@qt5022:~# lsusb -d 0af0: -vvv Bus 002 Device 003: ID 0af0:9200 Option Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0af0 Option idProduct 0x9200 bcdDevice 0.00 iManufacturer 3 Option N.V. iProduct 2 Globetrotter HSUPA Modem iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 200 bNumInterfaces 8 bConfigurationValue 1 iConfiguration 1 Option Configuration bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 4 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 5 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 6 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x88 EP 8 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x07 EP 7 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 7 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk-Only iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x08 EP 8 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x89 EP 9 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-02cdc_subset: deal with a device that needs reset for timeoutOliver Neukum
This device needs to be reset to recover from a timeout. Unfortunately this can be handled only at the level of the subdrivers. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-31AX88179_178A: Add ethtool ops for EEE supportFreddy Xin
Add functions to support ethtool EEE manipulating, and the EEE is disabled in default setting to enhance the compatibility with certain switch. Signed-off-by: Freddy Xin <freddy@asix.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30Revert "cdc_subset: deal with a device that needs reset for timeout"Linus Torvalds
This reverts commit 20fbe3ae990fd54fc7d1f889d61958bc8b38f254. As reported by Stephen Rothwell, it causes compile failures in certain configurations: drivers/net/usb/cdc_subset.c:360:15: error: 'dummy_prereset' undeclared here (not in a function) .pre_reset = dummy_prereset, ^ drivers/net/usb/cdc_subset.c:361:16: error: 'dummy_postreset' undeclared here (not in a function) .post_reset = dummy_postreset, ^ Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: David Miller <davem@davemloft.net> Cc: Oliver Neukum <oneukum@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-07-29cdc-ether: clean packet filter upon probeOliver Neukum
There are devices that don't do reset all the way. So the packet filter should be set to a sane initial value. Failure to do so leads to intermittent failures of DHCP on some systems under some conditions. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-29cdc_subset: deal with a device that needs reset for timeoutOliver Neukum
This device needs to be reset to recover from a timeout. Unfortunately this can be handled only at the level of the subdrivers. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-24r8152: fix the checking of the usb speedhayeswang
When the usb speed of the RTL8152 is not high speed, the USB_DEV_STAT[2:1] should be equal to [0 1]. That is, the STAT_SPEED_FULL should be equal to 2. There is a easy way to check the usb speed by the speed field of the struct usb_device. Use it to replace the original metheod. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Spotted-by: Andrey Utkin <andrey.krieger.utkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/infiniband/hw/cxgb4/device.c The cxgb4 conflict was simply overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-06 08:58:24 +0000