summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/rt2x00/rt2800lib.c
AgeCommit message (Collapse)Author
2012-05-08rt2x00: Add debugfs access for rfcsr registerAnisse Astier
RFCSR is only used in rt2800. For other chipsets, the debug struct for rfcsr should be zeroed, which isn't be an issue, since the code can now cope with that. Signed-off-by: Anisse Astier <anisse@astier.eu> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23rt2800: add chipset revision RT5390R supportAnisse Astier
About 70% of the chips with revision RT5390R initialize incorrectly, using the auxiliary antenna instead of the main one. The net result is that signal reception is very poor (no AP further than 1M). This chipset differs from RT5390 and RT5390F by its support of hardware antenna diversity. Therefore antenna selection should be done differently, by disabling software features and previously selected antenna. This changeset does just that, and makes all RT5390R work properly. This is based on Ralink's 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO driver. Signed-off-by: Anisse Astier <anisse@astier.eu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-13rt2800: initialize queues before giving up due to DMA errorJakub Kicinski
Don't immediately abort .start if DMA is busy before we initialize the queues. Some drivers do not deinitialize queues properly and we would fail to take over after them. This behaviour is consistent with legacy driver. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-13rt2800: add disabling of DMA before loading firmwareJakub Kicinski
Legacy driver disables DMA before loading firmware. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-13rt2800: introduce wpdma_disable functionJakub Kicinski
Introduce wpdma_disable function to simplify the code. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15rt2x00: Set IEEE80211_HW_REPORTS_TX_ACK_STATUS in rt2800Helmut Schaa
rt2800 already reports the tx ack status of each frame back to mac80211. Advertise this by setting IEEE80211_HW_REPORTS_TX_ACK_STATUS for rt2800. This allows some mac80211 features like frame loss notifications to work with rt2800. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27rt2x00:Add RT5372 chipset supportJohn Li
Signed-off-by: John Li <chen-yang.li@mediatek.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27rt2x00:Add VCO recalibrationJohn Li
Signed-off-by: John Li <chen-yang.li@mediatek.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22rt2x00:Add debug message for new chipsetJohn Li
Signed-off-by: John Li <chen-yang.li@mediatek.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-15Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: net/mac80211/debugfs_sta.c net/mac80211/sta_info.h
2012-02-08rt2x00: Correctly set txmixer_gain in RT3572 channel switching.Gertjan van Wingerde
Align with the v2.5.0.0 Ralink RT3572 driver. Save the EEPROM txmixer_gain values inside the rt2800 driver data structure and use it throughout the code. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-08rt2x00: Fix RT3572 channel switch RFCSR 7 programming.Gertjan van Wingerde
Align with the v2.5.0.0 Ralink RT3572 driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-08rt2x00: Align RT3572 channel switch RFCSR 1 programming with Ralink driver.Gertjan van Wingerde
Align with the v2.5.0.0 Ralink RT3572 driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-08rt2x00: Fix RFCSR 12 & 13 programming on RT3572 channel switching.Gertjan van Wingerde
Align with v2.5.0.0 Ralink RT3572 driver for 2.4GHz band channel switch. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-08rt2x00: Use saved BBP 25 and 26 values when configuring channel on RT3572.Gertjan van Wingerde
This brings the rt2800 channel switching code for RT3572 closer to the v2.5.0.0 Ralink RT3572 driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-08rt2x00: Use struct rt2x00_dev driver data in rt2800{pci,usb}.Gertjan van Wingerde
Start using the struct rt2x00_dev driver data in rt2800 for the calibration data. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-06rt2800: radio 3xxxx: channel switch RX/TX calibration fixesStanislaw Gruszka
Synchronize code with Ralink driver: 2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO Based on functions: RT30xx_ChipSwitchChannel RT33xx_ChipSwitchChannel NICInitRT3370RFRegisters and defines from: include/chip/rt33xx.h Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-06rt2800: radio 3xxx: add channel switch calibration routinesStanislaw Gruszka
Synchronize code with Ralink driver: 2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO Based on functions: RT33xx_ChipSwitchChannel RT30xx_ChipSwitchChannel Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-06rt2800: radio 3xxx: program RF_R1 during channel switchStanislaw Gruszka
Synchronize code with Ralink driver: 2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO Based on functions: RT33xx_ChipSwitchChannel RT30xx_ChipSwitchChannel RT33xx_Init Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-06rt2800: radio 3xxx: reprogram only lower bits of RF_R3Stanislaw Gruszka
Synchronize code with Ralink driver: 2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO (functions: RT33xx_ChipSwitchChannel() and RT30xx_ChipSwitchChannel()) Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-01rt2800lib: fix wrong -128dBm when signal is stronger than -12dBmLuigi Tarenga
This patch correct the type of variables containing the rssi values read from the rxwi. In function rt2800_agc_to_rssi() 3 variables (rssi0, rssi1, rss2) defined as int was assigned a 16bit signed values as unsigned. From a test with a hi-gain antenna I verified that the rxwi contains signed rssi values in the range -13/+81 (inclusive) with 0 as an error condition. In case of negative values a condition is triggered and the function return -128dBm while the signal is at its maximum. This patch correct the cast so negative values are not treated as very high positive values (ex. -13 does not become 243). Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-27rt2800: disable DMA after firmware loadStanislaw Gruszka
We can receive frames just after firmware load with current code, so disable DMA just after firmware is loaded, not before. Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-27rt2800usb: initialize H2M_INT_SRC registerStanislaw Gruszka
Ralink USB driver initialize H2M_INT_SRC to 0 after firmware load, and never touch this register later. It is not touched at all by Ralink PCI driver. Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00: Convert big if-statements to switch-statements.Gertjan van Wingerde
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00: Mark active channel's survey data as "in use"Helmut Schaa
This is just a cosmetical fix since we only return survey data for the active channel but it allows iw to show that the survey data is for the currently used channel. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-02Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/iwlwifi/iwl-agn.c drivers/net/wireless/libertas/cfg.c
2011-11-28rt2x00: Pass BlockAck and BlackAckReq frames to mac80211 in monitor modeHelmut Schaa
Previously BlockAcks were always dropped by the rt2800 hardware while BlockAckReqs were always accepted. However, both are only useful on monitor interfaces at the moment and both are control frames. So pass them up when mac80211 sets FIF_CONTROL. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-17rt2x00: Fix efuse EEPROM reading on PPC32.Gertjan van Wingerde
Fix __le32 to __le16 conversion of the first word of an 8-word block of EEPROM read via the efuse method. Reported-and-tested-by: Ingvar Hagelund <ingvar@redpill-linpro.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> CC: <stable@vger.kernel.org> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-03mac80211: pass vif param to conf_tx() callbackEliad Peller
tx params should be configured per interface. add ieee80211_vif param to the conf_tx callback, and change all the drivers that use this callback. The following spatch was used: @rule1@ struct ieee80211_ops ops; identifier conf_tx_op; @@ ops.conf_tx = conf_tx_op; @rule2@ identifier rule1.conf_tx_op; identifier hw, queue, params; @@ conf_tx_op ( - struct ieee80211_hw *hw, + struct ieee80211_hw *hw, struct ieee80211_vif *vif, u16 queue, const struct ieee80211_tx_queue_params *params) {...} Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27mac80211: add ieee80211_vif param to tsf functionsEliad Peller
TSF can be kept per vif. Add ieee80211_vif param to set/get/reset_tsf, and move the debugfs entries to the per-vif directory. Update all the drivers that implement these callbacks. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-20Merge branch 'master' of git://git.infradead.org/users/linville/wirelessJohn W. Linville
Conflicts: drivers/net/wireless/iwlwifi/iwl-pci.c drivers/net/wireless/iwlwifi/iwl-trans-pcie-tx.c drivers/net/wireless/rt2x00/rt2800usb.c drivers/net/wireless/wl12xx/main.c
2011-09-16rtl2800usb: Fix incorrect storage of MAC address on big-endian platformsLarry Finger
The eeprom data is stored in little-endian order in the rt2x00 library. As it was converted to cpu order in the read routines, the data need to be converted to LE on a big-endian platform. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-16rt2800pci: Fix compiler error on PowerPCLarry Finger
Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated if statement results in incorrect flow, whereas the equivalent switch statement works correctly. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14rt2x00: Use the available helper functions to initialize the WCID tableHelmut Schaa
Use rt2800_config_wcid and rt2800_delete_wcid_attr to initialize the WCID table instead of writing to the registers directly. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14rt2x00: Forbid aggregation for STAs not programmed into the hwHelmut Schaa
If a STA is not known by the hw (i.e. has no WCID assigned) don't allow aggregation since this might mess up tx status reports and we won't be able to distinguish the reports of multiple WCID-less STAs. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14rt2x00: Make use of sta_add/remove callbacks in rt2800Helmut Schaa
This allows us to assign a WCID to each STA even for STAs without crypto key. To achieve this search for an unused WCID in the HW WCID table and assign it to the according STA. When configuring a pairwise key for this STA we don't need to write the MAC address and BSSIDX anymore but just update the crypto related fields in the WCID_ATTR table. This has two advantages: 1) Setting a new key for an already available STA (PTK rekeying) is slightly less expensive and should improve performance in situations where a lot of rekeying happens (e.g. a huge number of stations and/or a small rekeying interval) 2) The TXWI now gets a WCID assigned for unencrypted frames which will be reflected in the corresponding tx status report. This should make tx status reports in unencrypted AP mode more reliable as we can distinguish between multiple key-less STAs. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14rt2x00: Remove incorrect led blinkHelmut Schaa
rt2800 devices are not capable of configuring arbitrary LED on/off periods. The LED_CFG register fields ON_PERIOD and OFF_PERIOD are only used by the hw when the LED mode is set to "blink upon TX". Hence, remove the blink callback. This will result in software emulation for LED blinking. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14rt2x00: Minor optimizazion in txdone pathHelmut Schaa
We can save an indirect function call + some instructions for fetching the actual function pointer by passing the driver specific txwi pointer directly from rt2800pci/rt2800usb to rt2800lib instead of using the rt2800_drv_get_txwi callback. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next ↵John W. Linville
into for-davem
2011-08-01rt2x00: rt2800: fix zeroing skb structureStanislaw Gruszka
We should clear skb->data not skb itself. Bug was introduced by: commit 0b8004aa12d13ec750d102ba4082a95f0107c649 "rt2x00: Properly reserve room for descriptors in skbs". Cc: stable@kernel.org # 2.6.36+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-08Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
2011-06-05drivers/net: Remove unnecessary semicolonsJoe Perches
Semicolons are not necessary after switch/while/for/if braces so remove them. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-01rt2x00: Move rt2800_txdone and rt2800_txdone_entry_check to rt2800usb.Gertjan van Wingerde
These two functions are only used by rt2800usb so they don't have to be in rt2800lib. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rt2x00: Add support for RT3572/RT3592/RT3592+Bluetooth combo cardGertjan van Wingerde
(based on an earlier patch submitted by Shiang) Add support for RT3572/RT3592/RT3592+Bluetooth combo card Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rt2x00: Don't disable G0 PA_PE bit in case of BT coexistence.Gertjan van Wingerde
(split off from the earlier RT35xx patch submitted by Shiang) Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rt2x00: Enable PA_PE bits in TX_PIN_CFG according to active band.Gertjan van Wingerde
(split off from the earlier RT35xx patch submitted by Shiang) There's no point in enabling the PA_PE bits for the bands that we are not active on. Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: drivers/net/wireless/iwlwifi/iwl-agn-tx.c net/mac80211/sta_info.h
2011-05-05rt2x00: Initial support for RT5370 USB devices.Gertjan van Wingerde
Add necessary RF chipset define and basic support for these devices. Tested-by: Juan Carlos Garza <juancarlosgarza@gmail.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-05Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: drivers/net/wireless/libertas/if_cs.c drivers/net/wireless/rtlwifi/pci.c net/bluetooth/l2cap_sock.c
2011-05-02rt2x00: Introduce capability flag for Bluetooth co-existence.Gertjan van Wingerde
Use flag instead of re-reading the eeprom every time. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-10 16:36:31 +0000