summaryrefslogtreecommitdiff
path: root/drivers/net/wireless
AgeCommit message (Collapse)Author
2015-05-29wlcore: add initial device tree support to the sdio moduleLuciano Coelho
If platform data is not available, try to get the required information from the device tree. Register an OF match table and parse the appropriate device tree nodes. Parse interrupt property only, for now. Signed-off-by: Luciano Coelho <coelho@ti.com>
2015-03-06MLK-10210 WIFI: ath6kl: Fixed the issue that warning messages were printed ↵Shenwei Wang
when uninstalling ath6kl_sdio after iperf test. When handing the command "ifconfig wlan0 down", the driver handler did not notify the disconnected event to the upper layer stack cfg80211, which would cause the relating resources unable to be released. A notification of disconnet event to cfg80211 was added when the driver was changed to the disconnect state. Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com> (cherry picked from commit 0b7b203a563ac98f5f0c5695a5149ec80d2114b4)
2015-01-22ath6kl: fix struct hif_scatter_req list handlingKalle Valo
Jason noticed that with Yocto GCC 4.8.1 ath6kl crashes with this iperf command: iperf -c $TARGET_IP -i 5 -t 50 -w 1M The crash was: Unable to handle kernel paging request at virtual address 1a480000 pgd = 80004000 [1a480000] *pgd=00000000 Internal error: Oops: 805 [#1] SMP ARM Modules linked in: ath6kl_sdio ath6kl_core [last unloaded: ath6kl_core] CPU: 0 PID: 1953 Comm: kworker/u4:0 Not tainted 3.10.9-1.0.0_alpha+dbf364b #1 Workqueue: ath6kl ath6kl_sdio_write_async_work [ath6kl_sdio] task: dcc9a680 ti: dc9ae000 task.ti: dc9ae000 PC is at v7_dma_clean_range+0x20/0x38 LR is at dma_cache_maint_page+0x50/0x54 pc : [<8001a6f8>] lr : [<800170fc>] psr: 20000093 sp : dc9afcf8 ip : 8001a748 fp : 00000004 r10: 00000000 r9 : 00000001 r8 : 00000000 r7 : 00000001 r6 : 00000000 r5 : 80cb7000 r4 : 03f9a480 r3 : 0000001f r2 : 00000020 r1 : 1a480000 r0 : 1a480000 Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 6cc5004a DAC: 00000015 Process kworker/u4:0 (pid: 1953, stack limit = 0xdc9ae238) Stack: (0xdc9afcf8 to 0xdc9b0000) fce0: 80c9b29c 00000000 fd00: 00000000 80017134 8001a748 dc302ac0 00000000 00000000 dc454a00 80c12ed8 fd20: dc115410 80017238 00000000 dc454a10 00000001 80017588 00000001 00000000 fd40: 00000000 dc302ac0 dc9afe38 dc9afe68 00000004 80c12ed8 00000000 dc454a00 fd60: 00000004 80436f88 00000000 00000000 00000600 0000ffff 0000000c 80c113c4 fd80: 80c9b29c 00000001 00000004 dc115470 60000013 dc302ac0 dc46e000 dc302800 fda0: dc9afe10 dc302b78 60000013 dc302ac0 dc46e000 00000035 dc46e5b0 80438c90 fdc0: dc9afe10 dc302800 dc302800 dc9afe68 dc9afe38 80424cb4 00000005 dc9afe10 fde0: dc9afe20 80424de8 dc9afe10 dc302800 dc46e910 80424e90 dc473c00 dc454f00 fe00: 000001b5 7f619d64 dcc7c830 00000000 00000000 dc9afe38 dc9afe68 00000000 fe20: 00000000 00000000 dc9afe28 dc9afe28 80424d80 00000000 00000035 9cac0034 fe40: 00000000 00000000 00000000 00000000 000001b5 00000000 00000000 00000000 fe60: dc9afe68 dc9afe10 3b9aca00 00000000 00000080 00000034 00000000 00000100 fe80: 00000000 00000000 dc9afe10 00000004 dc454a00 00000000 dc46e010 dc46e96c fea0: dc46e000 dc46e964 00200200 00100100 dc46e910 7f619ec0 00000600 80c0e770 fec0: dc15a900 dcc7c838 00000000 dc46e954 8042d434 dcc44680 dc46e954 dc004400 fee0: dc454500 00000000 00000000 dc9ae038 dc004400 8003c450 dcc44680 dc004414 ff00: dc46e954 dc454500 00000001 dcc44680 dc004414 dcc44698 dc9ae000 dc9ae030 ff20: 00000001 dc9ae000 dc004400 8003d158 8003d020 00000000 00000000 80c53941 ff40: dc9aff64 dcb71ea0 00000000 dcc44680 8003d020 00000000 00000000 00000000 ff60: 00000000 80042480 00000000 00000000 000000f8 dcc44680 00000000 00000000 ff80: dc9aff80 dc9aff80 00000000 00000000 dc9aff90 dc9aff90 dc9affac dcb71ea0 ffa0: 800423cc 00000000 00000000 8000e018 00000000 00000000 00000000 00000000 ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [<8001a6f8>] (v7_dma_clean_range+0x20/0x38) from [<800170fc>] (dma_cache_maint_page+0x50/0x54) [<800170fc>] (dma_cache_maint_page+0x50/0x54) from [<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c) [<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c) from [<80017238>] (arm_dma_map_page+0x64/0x68) [<80017238>] (arm_dma_map_page+0x64/0x68) from [<80017588>] (arm_dma_map_sg+0x7c/0xf4) [<80017588>] (arm_dma_map_sg+0x7c/0xf4) from [<80436f88>] (sdhci_send_command+0x894/0xe00) [<80436f88>] (sdhci_send_command+0x894/0xe00) from [<80438c90>] (sdhci_request+0xc0/0x1ec) [<80438c90>] (sdhci_request+0xc0/0x1ec) from [<80424cb4>] (mmc_start_request+0xb8/0xd4) [<80424cb4>] (mmc_start_request+0xb8/0xd4) from [<80424de8>] (__mmc_start_req+0x60/0x84) [<80424de8>] (__mmc_start_req+0x60/0x84) from [<80424e90>] (mmc_wait_for_req+0x10/0x20) [<80424e90>] (mmc_wait_for_req+0x10/0x20) from [<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio]) [<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio]) from [<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio]) [<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio]) from [<8003c450>] (process_one_work+0x10c/0x370) [<8003c450>] (process_one_work+0x10c/0x370) from [<8003d158>] (worker_thread+0x138/0x3fc) [<8003d158>] (worker_thread+0x138/0x3fc) from [<80042480>] (kthread+0xb4/0xb8) [<80042480>] (kthread+0xb4/0xb8) from [<8000e018>] (ret_from_fork+0x14/0x3c) Code: e1a02312 e2423001 e1c00003 f57ff04f (ee070f3a) ---[ end trace 0c038f0b8e0b67a3 ]--- Kernel panic - not syncing: Fatal exception Jason's analysis: "The GCC 4.8.1 compiler will not do the for-loop till scat_entries, instead, it only run one round loop. This may be caused by that the GCC 4.8.1 thought that the scat_list only have one item and then no need to do full iteration, but this is simply wrong by looking at the assebly code. This will cause the sg buffer not get set when scat_entries > 1 and thus lead to kernel panic. Note: This issue not observed with GCC 4.7.2, only found on the GCC 4.8.1)" Fix this by using the normal [0] style for defining unknown number of list entries following the struct. This also fixes corruption with scat_q_depth, which was mistankely added to the end of struct and overwritten if there were more than item in the scat list. Reported-by: Jason Liu <r64343@freescale.com> Tested-by: Jason Liu <r64343@freescale.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-06rt2x00: do not align payload on modern H/WStanislaw Gruszka
commit cfd9167af14eb4ec21517a32911d460083ee3d59 upstream. RT2800 and newer hardware require padding between header and payload if header length is not multiple of 4. For historical reasons we also align payload to to 4 bytes boundary, but such alignment is not needed on modern H/W. Patch fixes skb_under_panic problems reported from time to time: https://bugzilla.kernel.org/show_bug.cgi?id=84911 https://bugzilla.kernel.org/show_bug.cgi?id=72471 http://marc.info/?l=linux-wireless&m=139108549530402&w=2 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591 Panic happened because we eat 4 bytes of skb headroom on each (re)transmission when sending frame without the payload and the header length not being multiple of 4 (i.e. QoS header has 26 bytes). On such case because paylad_aling=2 is bigger than header_align=0 we increase header_align by 4 bytes. To prevent that we could change the check to: if (payload_length && payload_align > header_align) header_align += 4; but not aligning payload at all is more effective and alignment is not really needed by H/W (that has been tested on OpenWrt project for few years now). Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi> Debugged-by: Antti S. Lankila <alankila@bel.fi> Reported-by: Henrik Asp <solenskiner@gmail.com> Originally-From: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06ath9k: Fix RTC_DERIVED_CLK usageMiaoqing Pan
commit 4e6ce4dc7ce71d0886908d55129d5d6482a27ff9 upstream. Based on the reference clock, which could be 25MHz or 40MHz, AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550. But, when a chip reset is done, processing the initvals sets the register back to the default value. Fix this by moving the code in ath9k_hw_init_pll() to ar9003_hw_override_ini(). Also, do this override for AR9531. Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-21iwlwifi: configure the LTREmmanuel Grumbach
commit 9180ac50716a097a407c6d7e7e4589754a922260 upstream. The LTR is the handshake between the device and the root complex about the latency allowed when the bus exits power save. This configuration was missing and this led to high latency in the link power up. The end user could experience high latency in the network because of this. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-21mac80211_hwsim: release driver when ieee80211_register_hw failsJunjie Mao
commit 805dbe17d1c832ad341f14fae8cedf41b67ca6fa upstream. The driver is not released when ieee80211_register_hw fails in mac80211_hwsim_create_radio, leading to the access to the unregistered (and possibly freed) device in platform_driver_unregister: [ 0.447547] mac80211_hwsim: ieee80211_register_hw failed (-2) [ 0.448292] ------------[ cut here ]------------ [ 0.448854] WARNING: CPU: 0 PID: 1 at ../include/linux/kref.h:47 kobject_get+0x33/0x50() [ 0.449839] CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00001-gdd46990-dirty #2 [ 0.450813] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 0.451512] 00000000 00000000 78025e38 7967c6c6 78025e68 7905e09b 7988b480 00000000 [ 0.452579] 00000001 79887d62 0000002f 79170bb3 79170bb3 78397008 79ac9d74 00000001 [ 0.453614] 78025e78 7905e15d 00000009 00000000 78025e84 79170bb3 78397000 78025e8c [ 0.454632] Call Trace: [ 0.454921] [<7967c6c6>] dump_stack+0x16/0x18 [ 0.455453] [<7905e09b>] warn_slowpath_common+0x6b/0x90 [ 0.456067] [<79170bb3>] ? kobject_get+0x33/0x50 [ 0.456612] [<79170bb3>] ? kobject_get+0x33/0x50 [ 0.457155] [<7905e15d>] warn_slowpath_null+0x1d/0x20 [ 0.457748] [<79170bb3>] kobject_get+0x33/0x50 [ 0.458274] [<7925824f>] get_device+0xf/0x20 [ 0.458779] [<7925b5cd>] driver_detach+0x3d/0xa0 [ 0.459331] [<7925a3ff>] bus_remove_driver+0x8f/0xb0 [ 0.459927] [<7925bf80>] ? class_unregister+0x40/0x80 [ 0.460660] [<7925bad7>] driver_unregister+0x47/0x50 [ 0.461248] [<7925c033>] ? class_destroy+0x13/0x20 [ 0.461824] [<7925d07b>] platform_driver_unregister+0xb/0x10 [ 0.462507] [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9 [ 0.463161] [<79b30c58>] do_one_initcall+0x106/0x1a9 [ 0.463758] [<79b517b8>] ? if_spi_init_module+0xac/0xac [ 0.464393] [<79b517b8>] ? if_spi_init_module+0xac/0xac [ 0.465001] [<79071935>] ? parse_args+0x2f5/0x480 [ 0.465569] [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50 [ 0.466345] [<79b30dd9>] kernel_init_freeable+0xde/0x17d [ 0.466972] [<79b304d6>] ? do_early_param+0x7a/0x7a [ 0.467546] [<79677b1b>] kernel_init+0xb/0xe0 [ 0.468072] [<79075f42>] ? schedule_tail+0x12/0x40 [ 0.468658] [<79686580>] ret_from_kernel_thread+0x20/0x30 [ 0.469303] [<79677b10>] ? rest_init+0xc0/0xc0 [ 0.469829] ---[ end trace ad8ac403ff8aef5c ]--- [ 0.470509] ------------[ cut here ]------------ [ 0.471047] WARNING: CPU: 0 PID: 1 at ../kernel/locking/lockdep.c:3161 __lock_acquire.isra.22+0x7aa/0xb00() [ 0.472163] DEBUG_LOCKS_WARN_ON(id >= MAX_LOCKDEP_KEYS) [ 0.472774] CPU: 0 PID: 1 Comm: swapper Tainted: G W 3.17.0-00001-gdd46990-dirty #2 [ 0.473815] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 0.474492] 78025de0 78025de0 78025da0 7967c6c6 78025dd0 7905e09b 79888931 78025dfc [ 0.475515] 00000001 79888a93 00000c59 7907f33a 7907f33a 78028000 fffe9d09 00000000 [ 0.476519] 78025de8 7905e10e 00000009 78025de0 79888931 78025dfc 78025e24 7907f33a [ 0.477523] Call Trace: [ 0.477821] [<7967c6c6>] dump_stack+0x16/0x18 [ 0.478352] [<7905e09b>] warn_slowpath_common+0x6b/0x90 [ 0.478976] [<7907f33a>] ? __lock_acquire.isra.22+0x7aa/0xb00 [ 0.479658] [<7907f33a>] ? __lock_acquire.isra.22+0x7aa/0xb00 [ 0.480417] [<7905e10e>] warn_slowpath_fmt+0x2e/0x30 [ 0.480479] [<7907f33a>] __lock_acquire.isra.22+0x7aa/0xb00 [ 0.480479] [<79078aa5>] ? sched_clock_cpu+0xb5/0xf0 [ 0.480479] [<7907fd06>] lock_acquire+0x56/0x70 [ 0.480479] [<7925b5e8>] ? driver_detach+0x58/0xa0 [ 0.480479] [<79682d11>] mutex_lock_nested+0x61/0x2a0 [ 0.480479] [<7925b5e8>] ? driver_detach+0x58/0xa0 [ 0.480479] [<7925b5e8>] ? driver_detach+0x58/0xa0 [ 0.480479] [<7925b5e8>] driver_detach+0x58/0xa0 [ 0.480479] [<7925a3ff>] bus_remove_driver+0x8f/0xb0 [ 0.480479] [<7925bf80>] ? class_unregister+0x40/0x80 [ 0.480479] [<7925bad7>] driver_unregister+0x47/0x50 [ 0.480479] [<7925c033>] ? class_destroy+0x13/0x20 [ 0.480479] [<7925d07b>] platform_driver_unregister+0xb/0x10 [ 0.480479] [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9 [ 0.480479] [<79b30c58>] do_one_initcall+0x106/0x1a9 [ 0.480479] [<79b517b8>] ? if_spi_init_module+0xac/0xac [ 0.480479] [<79b517b8>] ? if_spi_init_module+0xac/0xac [ 0.480479] [<79071935>] ? parse_args+0x2f5/0x480 [ 0.480479] [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50 [ 0.480479] [<79b30dd9>] kernel_init_freeable+0xde/0x17d [ 0.480479] [<79b304d6>] ? do_early_param+0x7a/0x7a [ 0.480479] [<79677b1b>] kernel_init+0xb/0xe0 [ 0.480479] [<79075f42>] ? schedule_tail+0x12/0x40 [ 0.480479] [<79686580>] ret_from_kernel_thread+0x20/0x30 [ 0.480479] [<79677b10>] ? rest_init+0xc0/0xc0 [ 0.480479] ---[ end trace ad8ac403ff8aef5d ]--- [ 0.495478] BUG: unable to handle kernel paging request at 00200200 [ 0.496257] IP: [<79682de5>] mutex_lock_nested+0x135/0x2a0 [ 0.496923] *pde = 00000000 [ 0.497290] Oops: 0002 [#1] [ 0.497653] CPU: 0 PID: 1 Comm: swapper Tainted: G W 3.17.0-00001-gdd46990-dirty #2 [ 0.498659] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 0.499321] task: 78028000 ti: 78024000 task.ti: 78024000 [ 0.499955] EIP: 0060:[<79682de5>] EFLAGS: 00010097 CPU: 0 [ 0.500620] EIP is at mutex_lock_nested+0x135/0x2a0 [ 0.501145] EAX: 00200200 EBX: 78397434 ECX: 78397460 EDX: 78025e70 [ 0.501816] ESI: 00000246 EDI: 78028000 EBP: 78025e8c ESP: 78025e54 [ 0.502497] DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068 [ 0.503076] CR0: 8005003b CR2: 00200200 CR3: 01b9d000 CR4: 00000690 [ 0.503773] Stack: [ 0.503998] 00000000 00000001 00000000 7925b5e8 78397460 7925b5e8 78397474 78397460 [ 0.504944] 00200200 11111111 78025e70 78397000 79ac9d74 00000001 78025ea0 7925b5e8 [ 0.505451] 79ac9d74 fffffffe 00000001 78025ebc 7925a3ff 7a251398 78025ec8 7925bf80 [ 0.505451] Call Trace: [ 0.505451] [<7925b5e8>] ? driver_detach+0x58/0xa0 [ 0.505451] [<7925b5e8>] ? driver_detach+0x58/0xa0 [ 0.505451] [<7925b5e8>] driver_detach+0x58/0xa0 [ 0.505451] [<7925a3ff>] bus_remove_driver+0x8f/0xb0 [ 0.505451] [<7925bf80>] ? class_unregister+0x40/0x80 [ 0.505451] [<7925bad7>] driver_unregister+0x47/0x50 [ 0.505451] [<7925c033>] ? class_destroy+0x13/0x20 [ 0.505451] [<7925d07b>] platform_driver_unregister+0xb/0x10 [ 0.505451] [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9 [ 0.505451] [<79b30c58>] do_one_initcall+0x106/0x1a9 [ 0.505451] [<79b517b8>] ? if_spi_init_module+0xac/0xac [ 0.505451] [<79b517b8>] ? if_spi_init_module+0xac/0xac [ 0.505451] [<79071935>] ? parse_args+0x2f5/0x480 [ 0.505451] [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50 [ 0.505451] [<79b30dd9>] kernel_init_freeable+0xde/0x17d [ 0.505451] [<79b304d6>] ? do_early_param+0x7a/0x7a [ 0.505451] [<79677b1b>] kernel_init+0xb/0xe0 [ 0.505451] [<79075f42>] ? schedule_tail+0x12/0x40 [ 0.505451] [<79686580>] ret_from_kernel_thread+0x20/0x30 [ 0.505451] [<79677b10>] ? rest_init+0xc0/0xc0 [ 0.505451] Code: 89 d8 e8 cf 9b 9f ff 8b 4f 04 8d 55 e4 89 d8 e8 72 9d 9f ff 8d 43 2c 89 c1 89 45 d8 8b 43 30 8d 55 e4 89 53 30 89 4d e4 89 45 e8 <89> 10 8b 55 dc 8b 45 e0 89 7d ec e8 db af 9f ff eb 11 90 31 c0 [ 0.505451] EIP: [<79682de5>] mutex_lock_nested+0x135/0x2a0 SS:ESP 0068:78025e54 [ 0.505451] CR2: 0000000000200200 [ 0.505451] ---[ end trace ad8ac403ff8aef5e ]--- [ 0.505451] Kernel panic - not syncing: Fatal exception Fixes: 9ea927748ced ("mac80211_hwsim: Register and bind to driver") Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Junjie Mao <eternal.n08@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-14Revert "iwlwifi: mvm: treat EAPOLs like mgmt frames wrt rate"Emmanuel Grumbach
commit 1ffde699aae127e7abdb98dbdedc2cc6a973a1a1 upstream. This reverts commit aa11bbf3df026d6b1c6b528bef634fd9de7c2619. This commit was causing connection issues and is not needed if IWL_MVM_RS_RSSI_BASED_INIT_RATE is set to false by default. Regardless of the issues mentioned above, this patch added the following WARNING: WARNING: CPU: 0 PID: 3946 at drivers/net/wireless/iwlwifi/mvm/tx.c:190 iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]() Got an HT rate for a non data frame 0x8 CPU: 0 PID: 3946 Comm: wpa_supplicant Tainted: G O 3.17.0+ #6 Hardware name: LENOVO 20ANCTO1WW/20ANCTO1WW, BIOS GLET71WW (2.25 ) 07/02/2014 0000000000000009 ffffffff814fa911 ffff8804288db8f8 ffffffff81064f52 0000000000001808 ffff8804288db948 ffff88040add8660 ffff8804291b5600 0000000000000000 ffffffff81064fb7 ffffffffa07b73d0 0000000000000020 Call Trace: [<ffffffff814fa911>] ? dump_stack+0x41/0x51 [<ffffffff81064f52>] ? warn_slowpath_common+0x72/0x90 [<ffffffff81064fb7>] ? warn_slowpath_fmt+0x47/0x50 [<ffffffffa07a39ea>] ? iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm] [<ffffffffa07a3cf8>] ? iwl_mvm_tx_skb+0x48/0x3c0 [iwlmvm] [<ffffffffa079cb9b>] ? iwl_mvm_mac_tx+0x7b/0x180 [iwlmvm] [<ffffffffa0746ce9>] ? __ieee80211_tx+0x2b9/0x3c0 [mac80211] [<ffffffffa07492f3>] ? ieee80211_tx+0xb3/0x100 [mac80211] [<ffffffffa0749c49>] ? ieee80211_subif_start_xmit+0x459/0xca0 [mac80211] [<ffffffff814116e7>] ? dev_hard_start_xmit+0x337/0x5f0 [<ffffffff81430d46>] ? sch_direct_xmit+0x96/0x1f0 [<ffffffff81411ba3>] ? __dev_queue_xmit+0x203/0x4f0 [<ffffffff8142f670>] ? ether_setup+0x70/0x70 [<ffffffff814e96a1>] ? packet_sendmsg+0xf81/0x1110 [<ffffffff8140625c>] ? skb_free_datagram+0xc/0x40 [<ffffffff813f7538>] ? sock_sendmsg+0x88/0xc0 [<ffffffff813f7274>] ? move_addr_to_kernel.part.20+0x14/0x60 [<ffffffff811c47c2>] ? __inode_wait_for_writeback+0x62/0xb0 [<ffffffff813f7a91>] ? SYSC_sendto+0xf1/0x180 [<ffffffff813f88f9>] ? __sys_recvmsg+0x39/0x70 [<ffffffff8150066d>] ? system_call_fastpath+0x1a/0x1f ---[ end trace cc19a150d311fc63 ]--- which was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=85691 Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-14wireless: rt2x00: add new rt2800usb deviceCyril Brulebois
commit 664d6a792785cc677c2091038ce10322c8d04ae1 upstream. 0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle References: https://bugs.debian.org/766802 Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz> Signed-off-by: Cyril Brulebois <kibi@debian.org> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-14wireless: rt2x00: add new rt2800usb devicesXose Vazquez Perez
commit 6a06e554daef86c4e8d290284927b081fedb249e upstream. 0x0b05 0x17e8 RT5372 USB 2.0 bgn 2x2 ASUS USB-N14 0x0411 0x0253 RT5572 USB 2.0 abgn 2x2 BUFFALO WLP-U2-300D 0x0df6 0x0078 RT???? Sitecom N300 Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-14rt2x00: support Ralink 5362.Canek Peláez Valdés
commit ac0372abf8524a7572a9cdaac6495eb2eba20457 upstream. Signed-off-by: Canek Peláez Valdés <canek@ciencias.unam.mx> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-30rt2800: correct BBP1_TX_POWER_CTRL maskStanislaw Gruszka
commit 01f7feeaf4528bec83798316b3c811701bac5d3e upstream. Two bits control TX power on BBP_R1 register. Correct the mask, otherwise we clear additional bit on BBP_R1 register, what can have unknown, possible negative effect. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-30iwlwifi: Add missing PCI IDs for the 7260 seriesOren Givon
commit 4f08970f5284dce486f0e2290834aefb2a262189 upstream. Add 4 missing PCI IDs for the 7260 series. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05brcmfmac: handle IF event for P2P_DEVICE interfaceArend van Spriel
commit 87c4790330810fe5caf0172d9320cf24ef19cebe upstream. The firmware notifies about interface changes through the IF event which has a NO_IF flag that means host can ignore the event. This behaviour was introduced in the driver by: commit 2ee8382fc6c763c76396a6aaff77a27089eed3aa Author: Arend van Spriel <arend@broadcom.com> Date: Sat Aug 10 12:27:24 2013 +0200 brcmfmac: ignore IF event if firmware indicates it It turns out that the IF event for the P2P_DEVICE also has this flag set, but the event should not be ignored in this scenario. The mentioned commit caused a regression in 3.12 kernel in creation of the P2P_DEVICE interface. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05rtlwifi: rtl8192cu: Add new IDLarry Finger
commit c66517165610b911e4c6d268f28d8c640832dbd1 upstream. The Sitecom WLA-2102 adapter uses this driver. Reported-by: Nico Baggus <nico-linux@noci.xs4all.nl> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Nico Baggus <nico-linux@noci.xs4all.nl> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05iwlwifi: mvm: treat EAPOLs like mgmt frames wrt rateEyal Shapira
commit aa11bbf3df026d6b1c6b528bef634fd9de7c2619 upstream. Using the LQ table which is initially set according to the rssi could lead to EAPOLs being sent in high legacy rates like 54mbps. It's better to avoid sending EAPOLs in high rates as it reduces the chances of a successful 4-Way handshake. Avoid this and treat them like other mgmt frames which would initially get sent at the basic rate. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05iwlwifi: increase DEFAULT_MAX_TX_POWEREliad Peller
commit 22d059a5c7c5de61e53c88e30b65e55fbfd91e91 upstream. The chip is able to transmit up to 22dBm, so set the constant appropriately. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05iwlwifi: mvm: fix endianity issues with Smart Fifo commandsEmmanuel Grumbach
commit 86974bff066dd8b98be46d7c7d3aba89034f0833 upstream. This code was broken on big endian systems. Sparse didn't catch the bug since the firmware command was not tagged as little endian. Fix the bug for big endian systems and tag the field in the firmware command to prevent such issues in the future. Fixes: 1f3b0ff8ec ("iwlwifi: mvm: Add Smart FIFO support") Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05Revert "iwlwifi: dvm: don't enable CTS to self"Emmanuel Grumbach
commit f47f46d7b09cf1d09e4b44b6cc4dd7d68a08028c upstream. This reverts commit 43d826ca5979927131685cc2092c7ce862cb91cd. This commit caused packet loss. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05carl9170: fix sending URBs with wrong type when using full-speedRonald Wahl
commit 671796dd96b6cd85b75fba9d3007bcf7e5f7c309 upstream. The driver assumes that endpoint 4 is always an interrupt endpoint. Unfortunately the type differs between high-speed and full-speed configurations while in the former case it is indeed an interrupt endpoint this is not true for the latter case - here it is a bulk endpoint. When sending URBs with the wrong type the kernel will generate a warning message including backtrace. In this specific case there will be a huge amount of warnings which can bring the system to freeze. To fix this we are now sending URBs to endpoint 4 using the type found in the endpoint descriptor. A side note: The carl9170 firmware currently specifies endpoint 4 as interrupt endpoint even in the full-speed configuration but this has no relevance because before this firmware is loaded the endpoint type is as described above and after the firmware is running the stick is not reenumerated and so the old descriptor is used. Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-07ath9k: fix aggregation session lockupFelix Fietkau
commit c01fac1c77a00227f706a1654317023e3f4ac7f0 upstream. If an aggregation session fails, frames still end up in the driver queue with IEEE80211_TX_CTL_AMPDU set. This causes tx for the affected station/tid to stall, since ath_tx_get_tid_subframe returning packets to send. Fix this by clearing IEEE80211_TX_CTL_AMPDU as long as no aggregation session is running. Reported-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28iwlwifi: mvm: disable CTS to SelfEmmanuel Grumbach
commit dc271ee0d04d12d6bfabacbec803289a7072fbd9 upstream. Firmware folks seem say that this flag can make trouble. Drop it. The advantage of CTS to self is that it slightly reduces the cost of the protection, but make the protection less reliable. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28mwifiex: fix Tx timeout issueAmitkumar Karwar
commit d76744a93246eccdca1106037e8ee29debf48277 upstream. https://bugzilla.kernel.org/show_bug.cgi?id=70191 https://bugzilla.kernel.org/show_bug.cgi?id=77581 It is observed that sometimes Tx packet is downloaded without adding driver's txpd header. This results in firmware parsing garbage data as packet length. Sometimes firmware is unable to read the packet if length comes out as invalid. This stops further traffic and timeout occurs. The root cause is uninitialized fields in tx_info(skb->cb) of packet used to get garbage values. In this case if MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd header was skipped. This patch makes sure that tx_info is correctly initialized to fix the problem. Reported-by: Andrew Wiley <wiley.andrew.j@gmail.com> Reported-by: Linus Gasser <list@markas-al-nour.org> Reported-by: Michael Hirsch <hirsch@teufel.de> Tested-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Maithili Hinge <maithili@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28iwlwifi: dvm: don't enable CTS to selfEmmanuel Grumbach
commit 43d826ca5979927131685cc2092c7ce862cb91cd upstream. We should always prefer to use full RTS protection. Using CTS to self gives a meaningless improvement, but this flow is much harder for the firmware which is likely to have issues with it. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28iwlwifi: update the 7265 series HW IDsOren Givon
commit b3c063ae7279981f7161e63b44f214c62f122b32 upstream. Add one more 7265 series HW ID. Edit one existing 7265 series HW ID. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09brcmfmac: Fix brcmf_chip_ai_coredisable not applying reset bits to BCMA_IOCTLHans de Goede
commit ffa216bb5eecfce0f01b0b2a95d5c320dde90005 upstream. brcmfmac has been broken on my cubietruck with a BCM43362: brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1 brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d since commit 53036261033: "brcmfmac: update core reset and disable routines". The problem is that since this commit brcmf_chip_ai_resetcore no longer sets BCMA_IOCTL itself before bringing the core out of reset, instead relying on brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable to always set BCMA_IOCTL even if the core is already in reset. This fixes brcmfmac hanging in firmware loading on my board. Cc: stable@vger.kernel.org # v3.14 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> [arend@broadcom.com: rebase patch on linux-3.14.y branch] Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09b43: fix frequency reported on G-PHY with /new/ firmwareRafał Miłecki
commit 2fc68eb122c7ea6cd5be1fe7d6650c0beb2f4f40 upstream. Support for firmware rev 508+ was added years ago, but we never noticed it reports channel in a different way for G-PHY devices. Instead of offset from 2400 MHz it simply passes channel id (AKA hw_value). So far it was (most probably) affecting monitor mode users only, but the following recent commit made it noticeable for quite everybody: commit 3afc2167f60a327a2c1e1e2600ef209a3c2b75b7 Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Date: Tue Mar 4 16:50:13 2014 +0200 cfg80211/mac80211: ignore signal if the frame was heard on wrong channel Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09iwlwifi: pcie: try to get ownership several timesEmmanuel Grumbach
commit 501fd9895c1d7d8161ed56698ae2fccb10ef14f5 upstream. Some races with the hardware can happen when we take ownership of the device. Don't give up after the first try. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09rt2x00: fix rfkill regression on rt2500pciStanislaw Gruszka
commit 616a8394b5df8c88f4dd416f4527439a4e365034 upstream. As reported by Niels, starting rfkill polling during device probe (commit e2bc7c5, generally sane change) broke rfkill on rt2500pci device. I considered that bug as some initalization issue, which should be fixed on rt2500pci specific code. But after several attempts (see bug report for details) we fail to find working solution. Hence I decided to revert to old behaviour on rt2500pci to fix regression. Additionally patch also unregister rfkill on device remove instead of ifconfig down, what was another issue introduced by bad commit. Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=73821 Fixes: e2bc7c5f3cb8 ("rt2x00: Fix rfkill_polling register function.") Bisected-by: Niels <nille0386@googlemail.com> Reported-and-tested-by: Niels <nille0386@googlemail.com> Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09rt2x00: disable TKIP on USBStanislaw Gruszka
commit 8edcb0ba0d56f5914eef11eda6db8bfe74eb9ca8 upstream. On USB we can not get atomically TKIP key. We have to disable support for TKIP acceleration on USB hardware to avoid bug as showed bellow. [ 860.827243] BUG: scheduling while atomic: hostapd/3397/0x00000002 <snip> [ 860.827280] Call Trace: [ 860.827282] [<ffffffff81682ea6>] dump_stack+0x4d/0x66 [ 860.827284] [<ffffffff8167eb9b>] __schedule_bug+0x47/0x55 [ 860.827285] [<ffffffff81685bb3>] __schedule+0x733/0x7b0 [ 860.827287] [<ffffffff81685c59>] schedule+0x29/0x70 [ 860.827289] [<ffffffff81684f8a>] schedule_timeout+0x15a/0x2b0 [ 860.827291] [<ffffffff8105ac50>] ? ftrace_raw_event_tick_stop+0xc0/0xc0 [ 860.827294] [<ffffffff810c13c2>] ? __module_text_address+0x12/0x70 [ 860.827296] [<ffffffff81686823>] wait_for_completion_timeout+0xb3/0x140 [ 860.827298] [<ffffffff81080fc0>] ? wake_up_state+0x20/0x20 [ 860.827301] [<ffffffff814d5b3d>] usb_start_wait_urb+0x7d/0x150 [ 860.827303] [<ffffffff814d5cd5>] usb_control_msg+0xc5/0x110 [ 860.827305] [<ffffffffa02fb0c6>] rt2x00usb_vendor_request+0xc6/0x160 [rt2x00usb] [ 860.827307] [<ffffffffa02fb215>] rt2x00usb_vendor_req_buff_lock+0x75/0x150 [rt2x00usb] [ 860.827309] [<ffffffffa02fb393>] rt2x00usb_vendor_request_buff+0xa3/0xe0 [rt2x00usb] [ 860.827311] [<ffffffffa023d1a3>] rt2x00usb_register_multiread+0x33/0x40 [rt2800usb] [ 860.827314] [<ffffffffa05805f9>] rt2800_get_tkip_seq+0x39/0x50 [rt2800lib] [ 860.827321] [<ffffffffa0480f88>] ieee80211_get_key+0x218/0x2a0 [mac80211] [ 860.827322] [<ffffffff815cc68c>] ? __nlmsg_put+0x6c/0x80 [ 860.827329] [<ffffffffa051b02e>] nl80211_get_key+0x22e/0x360 [cfg80211] Reported-and-tested-by: Peter Wu <lekensteyn@gmail.com> Reported-and-tested-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: rs: clear per rate stats when aggregation changesEyal Shapira
commit b804eeb6649d75caeccbeae9f5623fc7b8bdfdfa upstream. The per rate stats should be cleared when aggregation state changes to avoid making rate scale decisions based on throughput figures which were collected prior to the aggregation state change and are now stale. While at it make sure any clearing of the per rate stats will get logged. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: add rs_rate_scale_clear_tbl_windows helper functionEliad Peller
commit 3ca71f603bb1a0f55e1ba24618ba45617bc36f70 upstream. instead of duplicating the same loop multiple times, use a new function for it. this will be later used also for clearing other windows in the table. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: disable beacon filteringEmmanuel Grumbach
commit 7bacc782270ff7db3b9f29fa5d24ad2ee1e8e81d upstream. This feature has been causing trouble - disable it for now. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: BT Coex - fix Look Up TableEmmanuel Grumbach
commit a6bc92803e7f765e02c923cf37c8e280e729642a upstream. A few entries were wrong and this caused throughput issues. Fixes: dac94da8dba3 ("iwlwifi: mvm: new BT Coex API") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: fix setting channel in monitor modeEmmanuel Grumbach
commit 1c4abec0baf25ffb92a28cc99d4231feeaa4d3f3 upstream. There was a deadlock in monitor mode when we were setting the channel if the channel was not 1. ====================================================== [ INFO: possible circular locking dependency detected ] 3.14.3 #4 Not tainted ------------------------------------------------------- iw/3323 is trying to acquire lock: (&local->chanctx_mtx){+.+.+.}, at: [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211] but task is already holding lock: (&local->iflist_mtx){+.+...}, at: [<ffffffffa0609e0a>] ieee80211_set_monitor_channel+0x5a/0x1b0 [mac80211] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&local->iflist_mtx){+.+...}: [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa0518189>] iwl_mvm_recalc_multicast+0x49/0xa0 [iwlmvm] [<ffffffffa051822e>] iwl_mvm_configure_filter+0x4e/0x70 [iwlmvm] [<ffffffffa05e6d43>] ieee80211_configure_filter+0x153/0x5f0 [mac80211] [<ffffffffa05e71f5>] ieee80211_reconfig_filter+0x15/0x20 [mac80211] [snip] -> #1 (&mvm->mutex){+.+.+.}: [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa0517246>] iwl_mvm_add_chanctx+0x56/0xe0 [iwlmvm] [<ffffffffa062ca1e>] ieee80211_new_chanctx+0x13e/0x410 [mac80211] [<ffffffffa062d953>] ieee80211_vif_use_channel+0x1c3/0x5a0 [mac80211] [<ffffffffa06035ab>] ieee80211_add_virtual_monitor+0x1ab/0x6b0 [mac80211] [<ffffffffa06052ea>] ieee80211_do_open+0xe6a/0x15a0 [mac80211] [<ffffffffa0605a79>] ieee80211_open+0x59/0x60 [mac80211] [snip] -> #0 (&local->chanctx_mtx){+.+.+.}: [<ffffffff810d6cb7>] check_prevs_add+0x977/0x980 [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211] [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211] [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211] [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211] [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211] [snip] other info that might help us debug this: Chain exists of: &local->chanctx_mtx --> &mvm->mutex --> &local->iflist_mtx Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&local->iflist_mtx); lock(&mvm->mutex); lock(&local->iflist_mtx); lock(&local->chanctx_mtx); *** DEADLOCK *** This deadlock actually occurs: INFO: task iw:3323 blocked for more than 120 seconds. Not tainted 3.14.3 #4 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. iw D ffff8800c8afcd80 4192 3323 3322 0x00000000 ffff880078fdb7e0 0000000000000046 ffff8800c8afcd80 ffff880078fdbfd8 00000000001d5540 00000000001d5540 ffff8801141b0000 ffff8800c8afcd80 ffff880078ff9e38 ffff880078ff9e38 ffff880078ff9e40 0000000000000246 Call Trace: [<ffffffff817ea841>] schedule_preempt_disabled+0x31/0x80 [<ffffffff817ebaed>] mutex_lock_nested+0x19d/0x4f0 [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa052a680>] ? iwl_mvm_power_mac_update_mode+0xc0/0xc0 [iwlmvm] [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa0529357>] _iwl_mvm_power_update_binding+0x27/0x80 [iwlmvm] [<ffffffffa0516eb1>] iwl_mvm_unassign_vif_chanctx+0x81/0xc0 [iwlmvm] [<ffffffffa062d3ff>] __ieee80211_vif_release_channel+0xdf/0x470 [mac80211] [<ffffffffa062e2fa>] ieee80211_vif_release_channel+0x4a/0xb0 [mac80211] [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211] [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211] [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211] [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211] This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75541 Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: pcie: disable interrupts upon PCIe allocEmmanuel Grumbach
commit 83f7a85f1134c6e914453f5747435415a23d516b upstream. In case RFKILL is in KILL position, the NIC will issue an interrupt straight away. This interrupt won't be sent because it is masked in the hardware. But if our interrupt service routine is called for another reason (SHARED_IRQ), then we'll look at the interrupt cause and service it. This can cause bad things if we are not ready yet. Explicitly clean the interrupt cause register to make sure we won't service anything before we are ready to. Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07brcmsmac: fix deadlock on missing firmwareEmil Goode
commit 8fc1e8c240aab968db658b2d8d079b4391207a36 upstream. When brcm80211 firmware is not installed networking hangs. A deadlock happens because we call ieee80211_unregister_hw() from the .start callback of struct ieee80211_ops. When .start is called we are under rtnl lock and ieee80211_unregister_hw() tries to take it again. Function call stack: dev_change_flags() __dev_change_flags() __dev_open() ASSERT_RTNL() <-- Assert rtnl lock ops->ndo_open() .ndo_open = ieee80211_open, ieee80211_open() ieee80211_do_open() drv_start() local->ops->start() .start = brcms_ops_start, brcms_ops_start() brcms_remove() ieee80211_unregister_hw() rtnl_lock() <-- Here we deadlock Introduced by: commit 25b5632fb35ca61b8ae3eee235edcdc2883f7a5e ("brcmsmac: request firmware in .start() callback") This patch fixes the bug by removing the call to brcms_remove() and moves the brcms_request_fw() call to the top of the .start callback to not initiate anything unless firmware is installed. Signed-off-by: Emil Goode <emilgoode@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07rtl8192cu: Fix unbalanced irq enable in error path of rtl92cu_hw_init()Ben Hutchings
commit 3234f5b06fc3094176a86772cc64baf3decc98fc upstream. Fixes: a53268be0cb9 ('rtlwifi: rtl8192cu: Fix too long disable of IRQs') Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07rt2x00: fix beaconing on USBStanislaw Gruszka
commit 8834d3608cc516f13e2e510f4057c263f3d2ce42 upstream. When disable beaconing we clear register with beacon and newer set it back, what make we stop send beacons infinitely. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: delay enabling smart FIFO until after beacon RXJohannes Berg
commit 0229cdafb6f67064a217591d48b0f6abf14e8385 upstream. If we have no beacon data before association, delay smart FIFO enablement until after we have this data. Not doing so can cause association failures in extremely silent environments (usually only a shielded box/room) as beacon RX is not sent to the host immediately, and then the association time event ends without the host receiving any beacon even though it was on the air - it's just stuck on the FIFO. Fixes: 1f3b0ff8ecce ("iwlwifi: mvm: Add Smart FIFO support") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: 7000: bump API to 9Emmanuel Grumbach
commit 431031851ea72a25abb9ad4df56a0f3b997e3026 upstream. This will allow to load the new firmware. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: rs: reinit rs if no tx for a long timeEyal Shapira
commit 87d5e4155c0088e6766b4f0193b63fa0eab71220 upstream. After being idle for a long time (>5sec) the rs statistics will be stale so we prefer to reset rs and start from legacy rates again. This gives better results when the attenuation increased signficantly (e.g. we got further from the AP) and after a while we start Tx Note that the first Tx after the idle period will still go out in the old modulation and rate but this seemed a simpler approach compared to adding a timer or modifying mac80211 for this. The negative impact is negligble as we'll recover quickly. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: rs: fix and cleanup rs_get_rate_actionEyal Shapira
commit e53839eb9882c99d3781eab0fe1b2d4369a6a2cc upstream. Change the down/upscale decision logic a bit to be based on different success ratio thresholds. This fixes the implementation compared to the rate scale algorithm which was planned to yield optimal results. Also fix a case where a lower rate wasn't explored despite being a potential for better throughput. While at it rewrite rs_get_rate_action to be more clear and clean. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: avoid searching unnecessary columnsEyal Shapira
commit d8fff919ecd7820084675c2814913445e95640ac upstream. Don't search columns which are unlikely to succeed as previous columns searched with less aggressive modulation failed. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: rs: fallback to legacy Tx columnsEyal Shapira
commit fd7dbee51b3d98402edb11fec0c93d96476e0ae1 upstream. Allow switching back to legacy Tx columns so we'll stop doing HT/VHT in case we're far from the AP. Stop active aggregation when making a deciding to stay in a legacy column. Despite having low legacy rates in the LQ table lower entries it doesn't help much in case we're doing aggregations as the aggregation was being transmitted in the initial rate of the table. This should help traffic stalls when far from the AP. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: add new 7265 HW IDsOren Givon
commit 80f2679e589503bd6cbaaa1f9c1cd9dd7dfae032 upstream. Add 2 new HW IDs for the 7265 series. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: mvm: rs: fix mimo delimiter in LQ cmdEyal Shapira
commit d9088f60425e0acd8a8f05fdfcfdd288d3258641 upstream. mimo_delim was always set to 0 instead of pointing to the first SISO entry after MIMO rates. This can cause keep transmitting in MIMO even when we shouldn't. For example when the peer is requesting static SMPS. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-07iwlwifi: add MODULE_FIRMWARE for 7265Emmanuel Grumbach
commit 08a732f4e4a842f0101e5ea03d79e9d613ffadbe upstream. It was missing. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-31wl18xx: align event mailbox with current fwEliad Peller
commit c0da71ff4d2cbf113465bff9a7c413154be25a89 upstream. Some fields are missing from the event mailbox struct definitions, which cause issues when trying to handle some events. Add the missing fields in order to align the struct size (without adding actual support for the new fields). Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org> Fixes: 028e724 ("wl18xx: move to new firmware (wl18xx-fw-3.bin)") Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-13rtlwifi: rtl8188ee: initialize packet_beaconColin Ian King
commit 328e203fc35f0b4f6df1c4943f74cf553bcc04f8 upstream. static code analysis from cppcheck reports: [drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:322]: (error) Uninitialized variable: packet_beacon packet_beacon is not initialized and hence packet_beacon contains garbage from the stack, so set it to false. Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2025-01-09 18:57:57 +0000