summaryrefslogtreecommitdiff
path: root/drivers/net/wireless
AgeCommit message (Collapse)Author
2018-09-19ath10k: disable bundle mgmt tx completion event supportSurabhi Vishnoi
[ Upstream commit 673bc519c55843c68c3aecff71a4101e79d28d2b ] The tx completion of multiple mgmt frames can be bundled in a single event and sent by the firmware to host, if this capability is not disabled explicitly by the host. If the host cannot handle the bundled mgmt tx completion, this capability support needs to be disabled in the wmi init cmd, sent to the firmware. Add the host capability indication flag in the wmi ready command, to let firmware know the features supported by the host driver. This field is ignored if it is not supported by firmware. Set the host capability indication flag(i.e. host_capab) to zero, for disabling the support of bundle mgmt tx completion. This will indicate the firmware to send completion event for every mgmt tx completion, instead of bundling them together and sending in a single event. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-19ath10k: prevent active scans on potential unusable channelsSven Eckelmann
[ Upstream commit 3f259111583801013cb605bb4414aa529adccf1c ] The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the scan. This results in transmission (probe requests) on channels which are not "available" for transmissions. Since the firmware is closed source and nothing can be done from our side to fix the problem in it, the driver has to work around this problem. The WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not scan actively on a channel unless an AP was detected on it. Simple probe requests will then be transmitted by the STA on the channel. ath10k must therefore also use this flag when it queues a radar channel for scanning. This should reduce the chance of an active scan when the channel might be "unusable" for transmissions. Fixes: e8a50f8ba44b ("ath10k: introduce DFS implementation") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-24brcmfmac: stop watchdog before detach and free everythingMichael Trimarchi
[ Upstream commit 373c83a801f15b1e3d02d855fad89112bd4ccbe0 ] Using built-in in kernel image without a firmware in filesystem or in the kernel image can lead to a kernel NULL pointer deference. Watchdog need to be stopped in brcmf_sdio_remove The system is going down NOW! [ 1348.110759] Unable to handle kernel NULL pointer dereference at virtual address 000002f8 Sent SIGTERM to all processes [ 1348.121412] Mem abort info: [ 1348.126962] ESR = 0x96000004 [ 1348.130023] Exception class = DABT (current EL), IL = 32 bits [ 1348.135948] SET = 0, FnV = 0 [ 1348.138997] EA = 0, S1PTW = 0 [ 1348.142154] Data abort info: [ 1348.145045] ISV = 0, ISS = 0x00000004 [ 1348.148884] CM = 0, WnR = 0 [ 1348.151861] user pgtable: 4k pages, 48-bit VAs, pgdp = (____ptrval____) [ 1348.158475] [00000000000002f8] pgd=0000000000000000 [ 1348.163364] Internal error: Oops: 96000004 [#1] PREEMPT SMP [ 1348.168927] Modules linked in: ipv6 [ 1348.172421] CPU: 3 PID: 1421 Comm: brcmf_wdog/mmc0 Not tainted 4.17.0-rc5-next-20180517 #18 [ 1348.180757] Hardware name: Amarula A64-Relic (DT) [ 1348.185455] pstate: 60000005 (nZCv daif -PAN -UAO) [ 1348.190251] pc : brcmf_sdiod_freezer_count+0x0/0x20 [ 1348.195124] lr : brcmf_sdio_watchdog_thread+0x64/0x290 [ 1348.200253] sp : ffff00000b85be30 [ 1348.203561] x29: ffff00000b85be30 x28: 0000000000000000 [ 1348.208868] x27: ffff00000b6cb918 x26: ffff80003b990638 [ 1348.214176] x25: ffff0000087b1a20 x24: ffff80003b94f800 [ 1348.219483] x23: ffff000008e620c8 x22: ffff000008f0b660 [ 1348.224790] x21: ffff000008c6a858 x20: 00000000fffffe00 [ 1348.230097] x19: ffff80003b94f800 x18: 0000000000000001 [ 1348.235404] x17: 0000ffffab2e8a74 x16: ffff0000080d7de8 [ 1348.240711] x15: 0000000000000000 x14: 0000000000000400 [ 1348.246018] x13: 0000000000000400 x12: 0000000000000001 [ 1348.251324] x11: 00000000000002c4 x10: 0000000000000a10 [ 1348.256631] x9 : ffff00000b85bc40 x8 : ffff80003be11870 [ 1348.261937] x7 : ffff80003dfc7308 x6 : 000000078ff08b55 [ 1348.267243] x5 : 00000139e1058400 x4 : 0000000000000000 [ 1348.272550] x3 : dead000000000100 x2 : 958f2788d6618100 [ 1348.277856] x1 : 00000000fffffe00 x0 : 0000000000000000 Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06rsi: Fix 'invalid vdd' warning in mmcSiva Rebbagondla
[ Upstream commit 78e450719c702784e42af6da912d3692fd3da0cb ] While performing cleanup, driver is messing with card->ocr value by not masking rocr against ocr_avail. Below panic is observed with some of the SDIO host controllers due to this. Issue is resolved by reverting incorrect modifications to vdd. [ 927.423821] mmc1: Invalid vdd 0x1f [ 927.423925] Modules linked in: rsi_sdio(+) cmac bnep arc4 rsi_91x mac80211 cfg80211 btrsi rfcomm bluetooth ecdh_generic [ 927.424073] CPU: 0 PID: 1624 Comm: insmod Tainted: G W 4.15.0-1000-caracalla #1 [ 927.424075] Hardware name: Dell Inc. Edge Gateway 3003/ , BIOS 01.00.06 01/22/2018 [ 927.424082] RIP: 0010:sdhci_set_power_noreg+0xdd/0x190[sdhci] [ 927.424085] RSP: 0018:ffffac3fc064b930 EFLAGS: 00010282 [ 927.424107] Call Trace: [ 927.424118] sdhci_set_power+0x5a/0x60 [sdhci] [ 927.424125] sdhci_set_ios+0x360/0x3b0 [sdhci] [ 927.424133] mmc_set_initial_state+0x92/0x120 [ 927.424137] mmc_power_up.part.34+0x33/0x1d0 [ 927.424141] mmc_power_up+0x17/0x20 [ 927.424147] mmc_sdio_runtime_resume+0x2d/0x50 [ 927.424151] mmc_runtime_resume+0x17/0x20 [ 927.424156] __rpm_callback+0xc4/0x200 [ 927.424161] ? idr_alloc_cyclic+0x57/0xd0 [ 927.424165] ? mmc_runtime_suspend+0x20/0x20 [ 927.424169] rpm_callback+0x24/0x80 [ 927.424172] ? mmc_runtime_suspend+0x20/0x20 [ 927.424176] rpm_resume+0x4b3/0x6c0 [ 927.424181] __pm_runtime_resume+0x4e/0x80 [ 927.424188] driver_probe_device+0x41/0x490 [ 927.424192] __driver_attach+0xdf/0xf0 [ 927.424196] ? driver_probe_device+0x490/0x490 [ 927.424201] bus_for_each_dev+0x6c/0xc0 [ 927.424205] driver_attach+0x1e/0x20 [ 927.424209] bus_add_driver+0x1f4/0x270 [ 927.424217] ? rsi_sdio_ack_intr+0x50/0x50 [rsi_sdio] [ 927.424221] driver_register+0x60/0xe0 [ 927.424227] ? rsi_sdio_ack_intr+0x50/0x50 [rsi_sdio] [ 927.424231] sdio_register_driver+0x20/0x30 [ 927.424237] rsi_module_init+0x16/0x40 [rsi_sdio] Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06brcmfmac: Add support for bcm43364 wireless chipsetSean Lanigan
[ Upstream commit 9c4a121e82634aa000a702c98cd6f05b27d6e186 ] Add support for the BCM43364 chipset via an SDIO interface, as used in e.g. the Murata 1FX module. The BCM43364 uses the same firmware as the BCM43430 (which is already included), the only difference is the omission of Bluetooth. However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place triggers the brcmfmac driver to load, and then correctly use the firmware file 'brcmfmac43430-sdio.bin'. Signed-off-by: Sean Lanigan <sean@lano.id.au> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06mwifiex: correct histogram data with appropriate indexXinming Hu
[ Upstream commit 30bfce0b63fa68c14ae1613eb9d259fa18644074 ] Correct snr/nr/rssi data index to avoid possible buffer underflow. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for BahamasSven Eckelmann
[ Upstream commit 699e2302c286a14afe7b7394151ce6c4e1790cc1 ] The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for BermudaSven Eckelmann
[ Upstream commit 9c790f2d234f65697e3b0948adbfdf36dbe63dd7 ] The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: FCC * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for SerbiaSven Eckelmann
[ Upstream commit 2a3169a54bb53717928392a04fb84deb765b51f1 ] The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for TanzaniaSven Eckelmann
[ Upstream commit 667ddac5745fb9fddfe8f7fd2523070f50bd4442 ] The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for UgandaSven Eckelmann
[ Upstream commit 1ea3986ad2bc72081c69f3fbc1e5e0eeb3c44f17 ] The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for APL2_FCCASven Eckelmann
[ Upstream commit 4f183687e3fad3ce0e06e38976cad81bc4541990 ] The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: FCC * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for APL13_WORLDSven Eckelmann
[ Upstream commit 9ba8df0c52b3e6baa436374b429d3d73bd09a320 ] The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for ETSI8_WORLDSven Eckelmann
[ Upstream commit 45faf6e096da8bb80e1ddf8c08a26a9601d9469e ] The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06ath: Add regulatory mapping for FCC3_ETSICSven Eckelmann
[ Upstream commit 01fb2994a98dc72c8818c274f7b5983d5dd885c7 ] The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06wlcore: sdio: check for valid platform device data before suspendEyal Reizer
[ Upstream commit 6e91d48371e79862ea2c05867aaebe4afe55a865 ] the wl pointer can be null In case only wlcore_sdio is probed while no WiLink module is successfully probed, as in the case of mounting a wl12xx module while using a device tree file configured with wl18xx related settings. In this case the system was crashing in wl1271_suspend() as platform device data is not set. Make sure wl the pointer is valid before using it. Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06mwifiex: handle race during mwifiex_usb_disconnectGanapathi Bhat
[ Upstream commit b817047ae70c0bd67b677b65d0d69d72cd6e9728 ] Race condition is observed during rmmod of mwifiex_usb: 1. The rmmod thread will call mwifiex_usb_disconnect(), download SHUTDOWN command and do wait_event_interruptible_timeout(), waiting for response. 2. The main thread will handle the response and will do a wake_up_interruptible(), unblocking rmmod thread. 3. On getting unblocked, rmmod thread will make rx_cmd.urb = NULL in mwifiex_usb_free(). 4. The main thread will try to resubmit rx_cmd.urb in mwifiex_usb_submit_rx_urb(), which is NULL. To fix, wait for main thread to complete before calling mwifiex_usb_free(). Signed-off-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06iwlwifi: pcie: fix race in Rx buffer allocatorShaul Triebitz
[ Upstream commit 0f22e40053bd5378ad1e3250e65c574fd61c0cd6 ] Make sure the rx_allocator worker is canceled before running the rx_init routine. rx_init frees and re-allocates all rxb's pages. The rx_allocator worker also allocates pages for the used rxb's. Running rx_init and rx_allocator simultaniously causes a kernel panic. Fix that by canceling the work in rx_init. Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-22rtlwifi: rtl8821ae: fix firmware is not ready to runPing-Ke Shih
commit 9a98302de19991d51e067b88750585203b2a3ab6 upstream. Without this patch, firmware will not run properly on rtl8821ae, and it causes bad user experience. For example, bad connection performance with low rate, higher power consumption, and so on. rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and each firmware has firmware data buffer and size individually. Original code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and this mismatch causes firmware checksum error, then firmware can't start. In this situation, driver gives message "Firmware is not ready to run!". Fixes: fe89707f0afa ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware") Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Cc: Stable <stable@vger.kernel.org> # 4.0+ Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-11ath10k: fix rfc1042 header retrieval in QCA4019 with eth decap modeVasanthakumar Thiagarajan
commit 2f38c3c01de945234d23dd163e3528ccb413066d upstream. Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future) rx_hdr_status is not padded to align in 4-byte boundary. Define a new hw_params field to handle different alignment behaviour between different hw. This patch fixes improper retrieval of rfc1042 header with QCA4019. This patch along with "ath10k: Properly remove padding from the start of rx payload" will fix traffic failure in ethernet decap mode for QCA4019. Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> [bwh: This just adds the part that was left out of the previous backport, commit b88fb9ea475a.] Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-13brcmfmac: Fix check for ISO3166 codeStefan Wahren
commit 9b9322db5c5a1917a66c71fe47c3848a9a31227e upstream. The commit "regulatory: add NUL to request alpha2" increases the length of alpha2 to 3. This causes a regression on brcmfmac, because brcmf_cfg80211_reg_notifier() expect valid ISO3166 codes in the complete array. So fix this accordingly. Fixes: 657308f73e67 ("regulatory: add NUL to request alpha2") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> [bwh: Backported to 4.4: adjust filename] Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-06rtlwifi: rtl8192cu: Remove variable self-assignment in rf.cMatthias Kaehlcke
commit fb239c1209bb0f0b4830cc72507cc2f2d63fadbd upstream. In _rtl92c_get_txpower_writeval_by_regulatory() the variable writeVal is assigned to itself in an if ... else statement, apparently only to document that the branch condition is handled and that a previously read value should be returned unmodified. The self-assignment causes clang to raise the following warning: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:304:13: error: explicitly assigning value of variable of type 'u32' (aka 'unsigned int') to itself [-Werror,-Wself-assign] writeVal = writeVal; Delete the branch with the self-assignment. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by: Guenter Roeck <groeck@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-30ath10k: Fix kernel panic while using worker (ath10k_sta_rc_update_wk)Karthikeyan Periyasamy
[ Upstream commit 8b2d93dd22615cb7f3046a5a2083a6f8bb8052ed ] When attempt to run worker (ath10k_sta_rc_update_wk) after the station object (ieee80211_sta) delete will trigger the kernel panic. This problem arise in AP + Mesh configuration, Where the current node AP VAP and neighbor node mesh VAP MAC address are same. When the current mesh node try to establish the mesh link with neighbor node, driver peer creation for the neighbor mesh node fails due to duplication MAC address. Already the AP VAP created with same MAC address. It is caused by the following scenario steps. Steps: 1. In above condition, ath10k driver sta_state callback (ath10k_sta_state) fails to do the state change for a station from IEEE80211_STA_NOTEXIST to IEEE80211_STA_NONE due to peer creation fails. Sta_state callback is called from ieee80211_add_station() to handle the new station (neighbor mesh node) request from the wpa_supplicant. 2. Concurrently ath10k receive the sta_rc_update callback notification from the mesh_neighbour_update() to handle the beacon frames of the above neighbor mesh node. since its atomic callback, ath10k driver queue the work (ath10k_sta_rc_update_wk) to handle rc update. 3. Due to driver sta_state callback fails (step 1), mac80211 free the station object. 4. When the worker (ath10k_sta_rc_update_wk) scheduled to run, it will access the station object which is already deleted. so it will trigger kernel panic. Added the peer exist check in sta_rc_update callback before queue the work. Kernel Panic log: Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = c0204000 [00000000] *pgd=00000000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM CPU: 1 PID: 1833 Comm: kworker/u4:2 Not tainted 3.14.77 #1 task: dcef0000 ti: d72b6000 task.ti: d72b6000 PC is at pwq_activate_delayed_work+0x10/0x40 LR is at pwq_activate_delayed_work+0xc/0x40 pc : [<c023f988>] lr : [<c023f984>] psr: 40000193 sp : d72b7f18 ip : 0000007a fp : d72b6000 r10: 00000000 r9 : dd404414 r8 : d8c31998 r7 : d72b6038 r6 : 00000004 r5 : d4907ec8 r4 : dcee1300 r3 : ffffffe0 r2 : 00000000 r1 : 00000001 r0 : 00000000 Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5787d Table: 595bc06a DAC: 00000015 ... Process kworker/u4:2 (pid: 1833, stack limit = 0xd72b6238) Stack: (0xd72b7f18 to 0xd72b8000) 7f00: 00000001 dcee1300 7f20: 00000001 c02410dc d8c31980 dd404400 dd404400 c0242790 d8c31980 00000089 7f40: 00000000 d93e1340 00000000 d8c31980 c0242568 00000000 00000000 00000000 7f60: 00000000 c02474dc 00000000 00000000 000000f8 d8c31980 00000000 00000000 7f80: d72b7f80 d72b7f80 00000000 00000000 d72b7f90 d72b7f90 d72b7fac d93e1340 7fa0: c0247404 00000000 00000000 c0208d20 00000000 00000000 00000000 00000000 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [<c023f988>] (pwq_activate_delayed_work) from [<c02410dc>] (pwq_dec_nr_in_flight+0x58/0xc4) [<c02410dc>] (pwq_dec_nr_in_flight) from [<c0242790>] (worker_thread+0x228/0x360) [<c0242790>] (worker_thread) from [<c02474dc>] (kthread+0xd8/0xec) [<c02474dc>] (kthread) from [<c0208d20>] (ret_from_fork+0x14/0x34) Code: e92d4038 e1a05000 ebffffbc[69210.619376] SMP: failed to stop secondary CPUs Rebooting in 3 seconds.. Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-30mac80211_hwsim: fix possible memory leak in hwsim_new_radio_nl()weiyongjun (A)
[ Upstream commit 0ddcff49b672239dda94d70d0fcf50317a9f4b51 ] 'hwname' is malloced in hwsim_new_radio_nl() and should be freed before leaving from the error handling cases, otherwise it will cause memory leak. Fixes: ff4dd73dd2b4 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-16ath10k: rebuild crypto header in rx data framesVasanthakumar Thiagarajan
commit 7eccb738fce57cbe53ed903ccf43f9ab257b15b3 upstream. Rx data frames notified through HTT_T2H_MSG_TYPE_RX_IND and HTT_T2H_MSG_TYPE_RX_FRAG_IND expect PN/TSC check to be done on host (mac80211) rather than firmware. Rebuild cipher header in every received data frames (that are notified through those HTT interfaces) from the rx_hdr_status tlv available in the rx descriptor of the first msdu. Skip setting RX_FLAG_IV_STRIPPED flag for the packets which requires mac80211 PN/TSC check support and set appropriate RX_FLAG for stripped crypto tail. Hw QCA988X, QCA9887, QCA99X0, QCA9984, QCA9888 and QCA4019 currently need the rebuilding of cipher header to perform PN/TSC check for replay attack. Please note that removing crypto tail for CCMP-256, GCMP and GCMP-256 ciphers in raw mode needs to be fixed. Since Rx with these ciphers in raw mode does not work in the current form even without this patch and removing crypto tail for these chipers needs clean up, raw mode related issues in CCMP-256, GCMP and GCMP-256 can be addressed in follow up patches. Tested-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-16ath10k: fix rfc1042 header retrieval in QCA4019 with eth decap modeVasanthakumar Thiagarajan
commit 2f38c3c01de945234d23dd163e3528ccb413066d upstream. Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future) rx_hdr_status is not padded to align in 4-byte boundary. Define a new hw_params field to handle different alignment behaviour between different hw. This patch fixes improper retrieval of rfc1042 header with QCA4019. This patch along with "ath10k: Properly remove padding from the start of rx payload" will fix traffic failure in ethernet decap mode for QCA4019. Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-16mac80211: allow not sending MIC up from driver for HW cryptoSara Sharon
commit f980ebc058c2fa2a552e495db1de0b330082ab70 upstream. When HW crypto is used, there's no need for the CCMP/GCMP MIC to be available to mac80211, and the hardware might have removed it already after checking. The MIC is also useless to have when the frame is already decrypted, so allow indicating that it's not present. Since we are running out of bits in mac80211_rx_flags, make the flags field a u64. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: Sriram R <srirrama@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-29Revert "ath10k: send (re)assoc peer command when NSS changed"Karthikeyan Periyasamy
commit 55cc11da69895a680940c1733caabc37be685f5e upstream. This reverts commit 55884c045d31a29cf69db8332d1064a1b61dd159. When Ath10k is in AP mode and an unassociated STA sends a VHT action frame (Operating Mode Notification for the NSS change) periodically to AP this causes ath10k to call ath10k_station_assoc() which sends WMI_PEER_ASSOC_CMDID during NSS update. Over the time (with a certain client it can happen within 15 mins when there are over 500 of these VHT action frames) continuous calls of WMI_PEER_ASSOC_CMDID cause firmware to assert due to resource exhaust. To my knowledge setting WMI_PEER_NSS peer param itself enough to handle NSS updates and no need to call ath10k_station_assoc(). So revert the original commit from 2014 as it's unclear why the change was really needed. Now the firmware assert doesn't happen anymore. Issue observed in QCA9984 platform with firmware version:10.4-3.5.3-00053. This Change tested in QCA9984 with firmware version: 10.4-3.5.3-00053 and QCA988x platform with firmware version: 10.2.4-1.0-00036. Firmware Assert log: ath10k_pci 0002:01:00.0: firmware crashed! (guid e61f1274-9acd-4c5b-bcca-e032ea6e723c) ath10k_pci 0002:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe ath10k_pci 0002:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 ath10k_pci 0002:01:00.0: firmware ver 10.4-3.5.3-00053 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast crc32 4c56a386 ath10k_pci 0002:01:00.0: board_file api 2 bmi_id 0:4 crc32 c2271344 ath10k_pci 0002:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1 ath10k_pci 0002:01:00.0: firmware register dump: ath10k_pci 0002:01:00.0: [00]: 0x0000000A 0x000015B3 0x00981E5F 0x00975B31 ath10k_pci 0002:01:00.0: [04]: 0x00981E5F 0x00060530 0x00000011 0x00446C60 ath10k_pci 0002:01:00.0: [08]: 0x0042F1FC 0x00458080 0x00000017 0x00000000 ath10k_pci 0002:01:00.0: [12]: 0x00000009 0x00000000 0x00973ABC 0x00973AD2 ath10k_pci 0002:01:00.0: [16]: 0x00973AB0 0x00960E62 0x009606CA 0x00000000 ath10k_pci 0002:01:00.0: [20]: 0x40981E5F 0x004066DC 0x00400000 0x00981E34 ath10k_pci 0002:01:00.0: [24]: 0x80983B48 0x0040673C 0x000000C0 0xC0981E5F ath10k_pci 0002:01:00.0: [28]: 0x80993DEB 0x0040676C 0x00431AB8 0x0045D0C4 ath10k_pci 0002:01:00.0: [32]: 0x80993E5C 0x004067AC 0x004303C0 0x0045D0C4 ath10k_pci 0002:01:00.0: [36]: 0x80994AAB 0x004067DC 0x00000000 0x0045D0C4 ath10k_pci 0002:01:00.0: [40]: 0x809971A0 0x0040681C 0x004303C0 0x00441B00 ath10k_pci 0002:01:00.0: [44]: 0x80991904 0x0040688C 0x004303C0 0x0045D0C4 ath10k_pci 0002:01:00.0: [48]: 0x80963AD3 0x00406A7C 0x004303C0 0x009918FC ath10k_pci 0002:01:00.0: [52]: 0x80960E80 0x00406A9C 0x0000001F 0x00400000 ath10k_pci 0002:01:00.0: [56]: 0x80960E51 0x00406ACC 0x00400000 0x00000000 ath10k_pci 0002:01:00.0: Copy Engine register dump: ath10k_pci 0002:01:00.0: index: addr: sr_wr_idx: sr_r_idx: dst_wr_idx: dst_r_idx: ath10k_pci 0002:01:00.0: [00]: 0x0004a000 15 15 3 3 ath10k_pci 0002:01:00.0: [01]: 0x0004a400 17 17 212 213 ath10k_pci 0002:01:00.0: [02]: 0x0004a800 21 21 20 21 ath10k_pci 0002:01:00.0: [03]: 0x0004ac00 25 25 27 25 ath10k_pci 0002:01:00.0: [04]: 0x0004b000 515 515 144 104 ath10k_pci 0002:01:00.0: [05]: 0x0004b400 28 28 155 156 ath10k_pci 0002:01:00.0: [06]: 0x0004b800 12 12 12 12 ath10k_pci 0002:01:00.0: [07]: 0x0004bc00 1 1 1 1 ath10k_pci 0002:01:00.0: [08]: 0x0004c000 0 0 127 0 ath10k_pci 0002:01:00.0: [09]: 0x0004c400 1 1 1 1 ath10k_pci 0002:01:00.0: [10]: 0x0004c800 0 0 0 0 ath10k_pci 0002:01:00.0: [11]: 0x0004cc00 0 0 0 0 ath10k_pci 0002:01:00.0: CE[1] write_index 212 sw_index 213 hw_index 0 nentries_mask 0x000001ff ath10k_pci 0002:01:00.0: CE[2] write_index 20 sw_index 21 hw_index 0 nentries_mask 0x0000007f ath10k_pci 0002:01:00.0: CE[5] write_index 155 sw_index 156 hw_index 0 nentries_mask 0x000001ff ath10k_pci 0002:01:00.0: DMA addr: nbytes: meta data: byte swap: gather: ath10k_pci 0002:01:00.0: [455]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [456]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [457]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [458]: 0x594a0038 0 0 0 1 ath10k_pci 0002:01:00.0: [459]: 0x580c0a42 0 0 0 0 ath10k_pci 0002:01:00.0: [460]: 0x594a0060 0 0 0 1 ath10k_pci 0002:01:00.0: [461]: 0x580c0c42 0 0 0 0 ath10k_pci 0002:01:00.0: [462]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [463]: 0x580c0c42 0 0 0 0 ath10k_pci 0002:01:00.0: [464]: 0x594a0038 0 0 0 1 ath10k_pci 0002:01:00.0: [465]: 0x580c0a42 0 0 0 0 ath10k_pci 0002:01:00.0: [466]: 0x594a0060 0 0 0 1 ath10k_pci 0002:01:00.0: [467]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [468]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [469]: 0x580c1c42 0 0 0 0 ath10k_pci 0002:01:00.0: [470]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [471]: 0x580c1c42 0 0 0 0 ath10k_pci 0002:01:00.0: [472]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [473]: 0x580c1c42 0 0 0 0 ath10k_pci 0002:01:00.0: [474]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [475]: 0x580c0642 0 0 0 0 ath10k_pci 0002:01:00.0: [476]: 0x594a0038 0 0 0 1 ath10k_pci 0002:01:00.0: [477]: 0x580c0842 0 0 0 0 ath10k_pci 0002:01:00.0: [478]: 0x594a0060 0 0 0 1 ath10k_pci 0002:01:00.0: [479]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [480]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [481]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [482]: 0x594a0038 0 0 0 1 ath10k_pci 0002:01:00.0: [483]: 0x580c0842 0 0 0 0 ath10k_pci 0002:01:00.0: [484]: 0x594a0060 0 0 0 1 ath10k_pci 0002:01:00.0: [485]: 0x580c0642 0 0 0 0 ath10k_pci 0002:01:00.0: [486]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [487]: 0x580c0642 0 0 0 0 ath10k_pci 0002:01:00.0: [488]: 0x594a0038 0 0 0 1 ath10k_pci 0002:01:00.0: [489]: 0x580c0842 0 0 0 0 ath10k_pci 0002:01:00.0: [490]: 0x594a0060 0 0 0 1 ath10k_pci 0002:01:00.0: [491]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [492]: 0x58174040 0 1 0 0 ath10k_pci 0002:01:00.0: [493]: 0x5a946040 0 1 0 0 ath10k_pci 0002:01:00.0: [494]: 0x59909040 0 1 0 0 ath10k_pci 0002:01:00.0: [495]: 0x5ae5a040 0 1 0 0 ath10k_pci 0002:01:00.0: [496]: 0x58096040 0 1 0 0 ath10k_pci 0002:01:00.0: [497]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [498]: 0x580c0642 0 0 0 0 ath10k_pci 0002:01:00.0: [499]: 0x5c1e0040 0 1 0 0 ath10k_pci 0002:01:00.0: [500]: 0x58153040 0 1 0 0 ath10k_pci 0002:01:00.0: [501]: 0x58129040 0 1 0 0 ath10k_pci 0002:01:00.0: [502]: 0x5952f040 0 1 0 0 ath10k_pci 0002:01:00.0: [503]: 0x59535040 0 1 0 0 ath10k_pci 0002:01:00.0: [504]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [505]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [506]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [507]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [508]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [509]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [510]: 0x594a0010 0 0 0 1 ath10k_pci 0002:01:00.0: [511]: 0x580c0042 0 0 0 0 ath10k_pci 0002:01:00.0: [512]: 0x5adcc040 0 1 0 0 ath10k_pci 0002:01:00.0: [513]: 0x5cf3d040 0 1 0 0 ath10k_pci 0002:01:00.0: [514]: 0x5c1e9040 64 1 0 0 ath10k_pci 0002:01:00.0: [515]: 0x00000000 0 0 0 0 Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-29ath9k_hw: check if the chip failed to wake upFelix Fietkau
commit a34d0a0da1abae46a5f6ebd06fb0ec484ca099d9 upstream. In an RFC patch, Sven Eckelmann and Simon Wunderlich reported: "QCA 802.11n chips (especially AR9330/AR9340) sometimes end up in a state in which a read of AR_CFG always returns 0xdeadbeef. This should not happen when when the power_mode of the device is ATH9K_PM_AWAKE." Include the check for the default register state in the existing MAC hang check. Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-24rtl8187: Fix NULL pointer dereference in priv->conf_mutexSudhir Sreedharan
commit 7972326a26b5bf8dc2adac575c4e03ee7e9d193a upstream. This can be reproduced by bind/unbind the driver multiple times in AM3517 board. Analysis revealed that rtl8187_start() was invoked before probe finishes(ie. before the mutex is initialized). INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250 Hardware name: Generic AM3517 (Flattened Device Tree) [<c010e0d8>] (unwind_backtrace) from [<c010beac>] (show_stack+0x10/0x14) [<c010beac>] (show_stack) from [<c017401c>] (register_lock_class+0x4f4/0x55c) [<c017401c>] (register_lock_class) from [<c0176fe0>] (__lock_acquire+0x74/0x1938) [<c0176fe0>] (__lock_acquire) from [<c0178cfc>] (lock_acquire+0xfc/0x23c) [<c0178cfc>] (lock_acquire) from [<c08aa2f8>] (mutex_lock_nested+0x50/0x3b0) [<c08aa2f8>] (mutex_lock_nested) from [<c05f5bf8>] (rtl8187_start+0x2c/0xd54) [<c05f5bf8>] (rtl8187_start) from [<c082dea0>] (drv_start+0xa8/0x320) [<c082dea0>] (drv_start) from [<c084d1d4>] (ieee80211_do_open+0x2bc/0x8e4) [<c084d1d4>] (ieee80211_do_open) from [<c069be94>] (__dev_open+0xb8/0x120) [<c069be94>] (__dev_open) from [<c069c11c>] (__dev_change_flags+0x88/0x14c) [<c069c11c>] (__dev_change_flags) from [<c069c1f8>] (dev_change_flags+0x18/0x48) [<c069c1f8>] (dev_change_flags) from [<c0710b08>] (devinet_ioctl+0x738/0x840) [<c0710b08>] (devinet_ioctl) from [<c067925c>] (sock_ioctl+0x164/0x2f4) [<c067925c>] (sock_ioctl) from [<c02883f8>] (do_vfs_ioctl+0x8c/0x9d0) [<c02883f8>] (do_vfs_ioctl) from [<c0288da8>] (SyS_ioctl+0x6c/0x7c) [<c0288da8>] (SyS_ioctl) from [<c0107760>] (ret_fast_syscall+0x0/0x1c) Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = cd1ec000 [00000000] *pgd=8d1de831, *pte=00000000, *ppte=00000000 Internal error: Oops: 817 [#1] PREEMPT ARM Modules linked in: CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250 Hardware name: Generic AM3517 (Flattened Device Tree) task: ce73eec0 task.stack: cd1ea000 PC is at mutex_lock_nested+0xe8/0x3b0 LR is at mutex_lock_nested+0xd0/0x3b0 Cc: stable@vger.kernel.org Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-13wl1251: check return from call to wl1251_acx_arp_ip_filterColin Ian King
[ Upstream commit ac1181c60822292176ab96912208ec9f9819faf8 ] Currently the less than zero error check on ret is incorrect as it is checking a far earlier ret assignment rather than the return from the call to wl1251_acx_arp_ip_filter. Fix this by adding in the missing assginment. Detected by CoverityScan, CID#1164835 ("Logically dead code") Fixes: 204cc5c44fb6 ("wl1251: implement hardware ARP filtering") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-13ray_cs: Avoid reading past end of bufferKees Cook
[ Upstream commit e48d661eb13f2f83861428f001c567fdb3f317e8 ] Using memcpy() from a buffer that is shorter than the length copied means the destination buffer is being filled with arbitrary data from the kernel rodata segment. In this case, the source was made longer, since it did not match the destination structure size. Additionally removes a needless cast. This was found with the future CONFIG_FORTIFY_SOURCE feature. Cc: Daniel Micay <danielmicay@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-13ath5k: fix memory leak on buf on failed eeprom readColin Ian King
[ Upstream commit 8fed6823e06e43ee9cf7c0ffecec2f9111ce6201 ] The AR5K_EEPROM_READ macro returns with -EIO if a read error occurs causing a memory leak on the allocated buffer buf. Fix this by explicitly calling ath5k_hw_nvram_read and exiting on the via the freebuf label that performs the necessary free'ing of buf when a read error occurs. Detected by CoverityScan, CID#1248782 ("Resource Leak") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-28rtlwifi: rtl8723be: Fix loss of signalLarry Finger
commit 78dc897b7ee67205423dbbc6b56be49fb18d15b5 upstream. In commit c713fb071edc ("rtlwifi: rtl8821ae: Fix connection lost problem correctly") a problem in rtl8821ae that caused loss of signal was fixed. That same problem has now been reported for rtl8723be. Accordingly, the ASPM L1 latency has been increased from 0 to 7 to fix the instability. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Tested-by: James Cameron <quozl@laptop.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-28brcmfmac: fix P2P_DEVICE ethernet address generationArend Van Spriel
commit 455f3e76cfc0d893585a5f358b9ddbe9c1e1e53b upstream. The firmware has a requirement that the P2P_DEVICE address should be different from the address of the primary interface. When not specified by user-space, the driver generates the MAC address for the P2P_DEVICE interface using the MAC address of the primary interface and setting the locally administered bit. However, the MAC address of the primary interface may already have that bit set causing the creation of the P2P_DEVICE interface to fail with -EBUSY. Fix this by using a random address instead to determine the P2P_DEVICE address. Cc: stable@vger.kernel.org # 3.10.y Reported-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24rtlwifi: rtl_pci: Fix the bug when inactiveps is enabled.Tsang-Shian Lin
[ Upstream commit b7573a0a27bfa8270dea9b145448f6884b7cacc1 ] Reset the driver current tx read/write index to zero when inactiveps nic out of sync with HW state. Wrong driver tx read/write index will cause Tx fail. Signed-off-by: Tsang-Shian Lin <thlin@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24rndis_wlan: add return value validationPan Bian
[ Upstream commit 9dc7efd3978aa67ae598129d2a3f240b390ce508 ] Function create_singlethread_workqueue() will return a NULL pointer if there is no enough memory, and its return value should be validated before using. However, in function rndis_wlan_bind(), its return value is not checked. This may cause NULL dereference bugs. This patch fixes it. Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24mt7601u: check return value of alloc_skbPan Bian
[ Upstream commit 5fb01e91daf84ad1e50edfcf63116ecbe31e7ba7 ] Function alloc_skb() will return a NULL pointer if there is no enough memory. However, in function mt7601u_mcu_msg_alloc(), its return value is not validated before it is used. This patch fixes it. Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-24ath: Fix updating radar flags for coutry code IndiaMohammed Shafi Shajakhan
[ Upstream commit c0c345d4cacc6a1f39d4856f37dcf6e34f51a5e4 ] As per latest regulatory update for India, channel 52, 56, 60, 64 is no longer restricted to DFS. Enabling DFS/no infra flags in driver results in applying all DFS related restrictions (like doing CAC etc before this channel moves to 'available state') for these channels even though the country code is programmed as 'India' in he hardware, fix this by relaxing the frequency range while applying RADAR flags only if the country code is programmed to India. If the frequency range needs to modified based on different country code, ath_is_radar_freq can be extended/modified dynamically. Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22mac80211_hwsim: enforce PS_MANUAL_POLL to be set after PS_ENABLEDAdiel Aloni
[ Upstream commit e16ea4bb516bc21ea2202f2107718b29218bea59 ] Enforce using PS_MANUAL_POLL in ps hwsim debugfs to trigger a poll, only if PS_ENABLED was set before. This is required due to commit c9491367b759 ("mac80211: always update the PM state of a peer on MGMT / DATA frames") that enforces the ap to check only mgmt/data frames ps bit, and then update station's power save accordingly. When sending only ps-poll (control frame) the ap will not be aware that the station entered power save. Setting ps enable before triggering ps_poll, will send NDP with PM bit enabled first. Signed-off-by: Adiel Aloni <adiel.aloni@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22ath10k: fix invalid STS_CAP_OFFSET_MASKBen Greear
[ Upstream commit 8cec57f5277ef0e354e37a0bf909dc71bc1f865b ] The 10.4 firmware defines this as a 3-bit field, as does the mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF at least in the firmware header I have seen. This patch fixes the ath10k wmi header to match the firmware. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22ath10k: update tdls teardown state to targetManikanta Pubbisetty
[ Upstream commit 424ea0d174e82365f85c6770225dba098b8f1d5f ] It is required to update the teardown state of the peer when a tdls link with that peer is terminated. This information is useful for the target to perform some cleanups wrt the tdls peer. Without proper cleanup, target assumes that the peer is connected and blocks future connection requests, updating the teardown state of the peer addresses the problem. Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version. Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22wil6210: fix memory access violation in wil_memcpy_from/toio_32Dedy Lansky
[ Upstream commit 0f6edfe2bbbb59d161580cb4870fcc46f5490f85 ] In case count is not multiple of 4, there is a read access in wil_memcpy_toio_32() from outside src buffer boundary. In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is a write access to outside dst io memory boundary. Fix these issues with proper handling of the last 1 to 4 copied bytes. Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22ath10k: disallow DFS simulation if DFS channel is not enabledMohammed Shafi Shajakhan
[ Upstream commit ca07baab0b1e627ae1d4a55d190fb1c9d32a3445 ] If DFS is not enabled in hostapd (ieee80211h=0) DFS channels shall not be available for use even though the hardware may have the capability to support DFS. With this configuration (DFS disabled in hostapd) trying to bring up ath10k device in DFS channel for AP mode fails and trying to simulate DFS in ath10k debugfs results in a warning in cfg80211 complaining invalid channel and this should be avoided in the driver itself rather than false propogating RADAR detection to mac80211/cfg80211. Fix this by checking for the first vif 'is_started' state(should work for client mode as well) as all the vifs shall be configured for the same channel sys/kernel/debug/ieee80211/phy1/ath10k# echo 1 > dfs_simulate_radar WARNING: at net/wireless/chan.c:265 cfg80211_radar_event+0x24/0x60 Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211] [<c022f2d4>] (warn_slowpath_null) from [<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211]) [<bf72dab8>] (cfg80211_radar_event [cfg80211]) from [<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211]) [<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from [<c0242320>] (process_one_work+0x20c/0x32c) WARNING: at net/wireless/nl80211.c:2488 nl80211_get_mpath+0x13c/0x4cc Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211] [<c022f2d4>] (warn_slowpath_null) from [<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211]) [<bf72dab8>] (cfg80211_radar_event [cfg80211]) from [<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211]) [<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from [<c0242320>] (process_one_work+0x20c/0x32c) Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22ath10k: fix a warning during channel switch with multiple vapsMohammed Shafi Shajakhan
[ Upstream commit c73f8c00330f59ce9b1ace9ff698aca83390d358 ] Doing a channel switch via hostapd_cli seems to update the new channel context for each VAP's appropriately as below in 'ath10k_mac_update_vif_chan', hence we can safely suppress the warning that shows up during this operation and dump the warning only if no vaps are available for channel switch hostapd_cli -i wlan0 chan_switch 5 5200 OK ath10k_pci : mac chanctx switch n_vifs 3 mode 1 ath10k_pci : mac chanctx switch vdev_id 2 freq 5180->5200 width 0->0 ath10k_pci : mac chanctx switch vdev_id 1 freq 5180->5200 width 0->0 ath10k_pci : mac chanctx switch vdev_id 0 freq 5180->5200 width 0->0 Call Trace: WARNING: backports-20161201-3.14.77-9ab3068/drivers/net/wireless/ath/ath10k/mac.c:7126 [<c022f2d4>] (warn_slowpath_null) from [<bf7f150c>] (ath10k_reconfig_complete+0xe4/0x25c [ath10k_core]) [<bf7f150c>] (ath10k_reconfig_complete [ath10k_core]) [<bf7f35f0>] (ath10k_mac_vif_ap_csa_work+0x214/0x370 [ath10k_core]) [<bf7f38b8>] (ath10k_mac_op_change_chanctx+0x108/0x128 [ath10k_core]) [<bf782ac0>] (ieee80211_recalc_chanctx_min_def+0x30c/0x430 [mac80211]) [<bf7830a4>] (ieee80211_recalc_smps_chanctx+0x2ec/0x840 [mac80211]) [<bf7843e8>] (ieee80211_vif_use_reserved_context+0x7c/0xf8 [mac80211]) [<bf7843e8>] (ieee80211_vif_use_reserved_context [mac80211]) [<bf76e5d4>] (ieee80211_csa_finalize_work+0x5c/0x88 [mac80211]) Fixes: d7bf4b4aba05 ("ath10k: fix ar->rx_channel updating logic") Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-25wireless: cw1200: use __maybe_unused to hide pm functions_Arnd Bergmann
commit 836856e3bd61d0644e5178a2c1b51d90459e2788 upstream. The cw1200 uses #ifdef to check for CONFIG_PM, but then uses SIMPLE_DEV_PM_OPS, which leaves the references out when CONFIG_PM_SLEEP is not defined, so we get a warning with PM=y && PM_SLEEP=n: drivers/net/wireless/st/cw1200/cw1200_spi.c:450:12: error: 'cw1200_spi_suspend' defined but not used [-Werror=unused-function] This removes the incorrect #ifdef and instead uses a __maybe_unused annotation to let the compiler know it can silently drop the function definition. For the DEV_PM_OPS definition, we can use an IS_ENABLED() check to avoid defining the structure when CONFIG_PM is not set without the #ifdef. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-25cw1200: fix bogus maybe-uninitialized warningArnd Bergmann
commit 7fc1503c906f0fac62d3506a6e993e49fb996248 upstream. On x86, the cw1200 driver produces a rather silly warning about the possible use of the 'ret' variable without an initialization presumably after being confused by the architecture specific definition of WARN_ON: drivers/net/wireless/st/cw1200/wsm.c: In function ‘wsm_handle_rx’: drivers/net/wireless/st/cw1200/wsm.c:1457:9: error: ‘ret’ may be used uninitialized in this function [-Werror=maybe-uninitialized] We have already checked that 'count' is larger than 0 here, so we know that 'ret' is initialized. Changing the 'for' loop into do/while also makes this clear to the compiler. Suggested-by: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-25rtlwifi: fix gcc-6 indentation warningArnd Bergmann
commit 2acd846485549655582ee379ceb966206f91e6f8 upstream. The rtl8821ae_dm_txpower_tracking_callback_thermalmeter function contains a call to RT_TRACE() that is indented in a misleading way, as pointed out by a gcc-6 warning: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c: In function 'rtl8821ae_dm_txpower_tracking_callback_thermalmeter': drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2491:4: error: statement is indented as if it were guarded by... RT_TRACE(rtlpriv, COMP_POWER_TRACKING, DBG_LOUD, ^~~~~~~~ drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2488:3: note: ...this 'for' clause, but it is not for (p = RF90_PATH_A; p < MAX_PATH_NUM_8821A; p++) ^~~ It is clear from the context that the call was not meant to be part of the loop and only the indentation is wrong, so this removes the extra tabs. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-22rtlwifi: rtl8821ae: Fix connection lost problem correctlyLarry Finger
commit c713fb071edc0efc01a955f65a006b0e1795d2eb upstream. There has been a coding error in rtl8821ae since it was first introduced, namely that an 8-bit register was read using a 16-bit read in _rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b75 ("rtlwifi: Fix alignment issues"); however, this change led to instability in the connection. To restore stability, this change was reverted in commit b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection lost problem"). Unfortunately, the unaligned access causes machine checks in ARM architecture, and we were finally forced to find the actual cause of the problem on x86 platforms. Following a suggestion from Pkshih <pkshih@realtek.com>, it was found that increasing the ASPM L1 latency from 0 to 7 fixed the instability. This parameter was varied to see if a smaller value would work; however, it appears that 7 is the safest value. A new symbol is defined for this quantity, thus it can be easily changed if necessary. Fixes: b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection lost problem") Cc: Stable <stable@vger.kernel.org> # 4.14+ Fix-suggested-by: Pkshih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3 Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-20ath9k: fix tx99 potential info leakMiaoqing Pan
[ Upstream commit ee0a47186e2fa9aa1c56cadcea470ca0ba8c8692 ] When the user sets count to zero the string buffer would remain completely uninitialized which causes the kernel to parse its own stack data, potentially leading to an info leak. In addition to that, the string might be not terminated properly when the user data does not contain a 0-terminator. Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Reviewed-by: Christoph Böhmwalder <christoph@boehmwalder.at> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2025-09-16 07:36:52 +0000