| Age | Commit message (Collapse) | Author |
|---|
|
commit 5523d11cc46393a1e61b7ef4a0b2d4e7ed9521e4 upstream.
We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere. In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.
Remove the color increment to use always zero and avoid reaching 255.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd66fc1cafd72ddf27dbec3a5e29e99839d1bc84 upstream.
When iwl_mvm_power_update_mac() is called, we have already added the
mac context, so if this call fails we should remove the mac.
Fixes: commit e5e7aa8e2561 ('iwlwifi: mvm: refactor power code')
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2cee4762c528a9bd2cdff793197bf591a2196c11 upstream.
These are coming from the FW and are used to access arrays.
Bad values can cause an out of bounds access so discard
such ba_notifs and warn.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd8f438405032ac8ff88bd8f2eca5e0c0063b14b upstream.
The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e2a4800e75780ccf4e6c2487f82b688ba736eb18 ]
When we've run out of space in the output buffer to store more data, we
will call zlib_deflate with a NULL output buffer until we've consumed
remaining input.
When this happens, olen contains the size the output buffer would have
consumed iff we'd have had enough room.
This can later cause skb_over_panic when ppp_generic skb_put()s
the returned length.
Reported-by: Iain Douglas <centos@1n6.org.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6088beef3f7517717bd21d90b379714dd0837079 ]
NAPI poll logic now enforces that a poller returns exactly the budget
when it wants to be called again.
If a driver limits TX completion, it has to return budget as well when
the limit is hit, not the number of received packets.
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade567f ("net: less interrupt masking in NAPI")
Cc: Manish Chopra <manish.chopra@qlogic.com>
Acked-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 02a54164c52ed6eca3089a0d402170fbf34d6cf5 upstream.
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Fixes: d9ba8f9e6298 (driver: net: ethernet: cpsw: dual emac interface implementation)
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e638642b08c170d2021b706f0b1c4f4ae93d8cbd upstream.
While being in an ERROR_WARNING state, and receiving further
bus error events with error counters still in the ERROR_WARNING
range of 97-127 inclusive, the state handling code erroneously
reverts back to ERROR_ACTIVE.
Per the CAN standard, only revert to ERROR_ACTIVE when the
error counters are less than 96.
Moreover, in certain Kvaser models, the BUS_ERROR flag is
always set along with undefined bits in the M16C status
register. Thus use bitwise operators instead of full equality
for checking that register against bus errors.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 14c10c2a1dd8eb8e00b750b521753260befa2789 upstream.
On some x86 laptops, plugging a Kvaser device again after an
unplug makes the firmware always ignore the very first command.
For such a case, provide some room for retries instead of
completely exiting the driver init code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3803fa6977f1de15fda4e8646c8fec97c8045cae upstream.
Send expected argument to the URB completion hander: a CAN
netdevice instead of the network interface private context
`kvaser_usb_net_priv'.
This was discovered by having some garbage in the kernel
log in place of the netdevice names: can0 and can1.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ded5006667318c06df875609535176bd33f243a1 upstream.
Upon receiving a hardware event with the BUS_RESET flag set,
the driver kills all of its anchored URBs and resets all of
its transmit URB contexts.
Unfortunately it does so under the context of URB completion
handler `kvaser_usb_read_bulk_callback()', which is often
called in an atomic context.
While the device is flooded with many received error packets,
usb_kill_urb() typically sleeps/reschedules till the transfer
request of each killed URB in question completes, leading to
the sleep in atomic bug. [3]
In v2 submission of the original driver patch [1], it was
stated that the URBs kill and tx contexts reset was needed
since we don't receive any tx acknowledgments later and thus
such resources will be locked down forever. Fortunately this
is no longer needed since an earlier bugfix in this patch
series is now applied: all tx URB contexts are reset upon CAN
channel close. [2]
Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF
event, which is the recommended handling method advised by
the device manufacturer.
[1] http://article.gmane.org/gmane.linux.network/239442
http://www.webcitation.org/6Vr2yagAQ
[2] can: kvaser_usb: Reset all URB tx contexts upon channel close
889b77f7fd2bcc922493d73a4c51d8a851505815
[3] Stacktrace:
<IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57
[<ffffffff8158b60c>] __schedule_bug+0x41/0x4f
[<ffffffff815904b1>] __schedule+0x5f1/0x700
[<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10
[<ffffffff81590684>] schedule+0x24/0x70
[<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0
[<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110
[<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80
[<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb]
[<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb]
[<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20
[<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb]
[<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0
[<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110
[<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd]
[<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20
[<ffffffff81069f65>] ? local_clock+0x15/0x30
[<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd]
[<ffffffff814fbb31>] ? process_backlog+0xb1/0x130
[<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd]
[<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30
[<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120
[<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60
[<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110
[<ffffffff81004dfd>] handle_irq+0x1d/0x30
[<ffffffff81004727>] do_IRQ+0x57/0x100
[<ffffffff8159482a>] common_interrupt+0x6a/0x6a
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9b1087aa5e86448fe6ad40a58964e35f3ba423d5 upstream.
When changing flags in the CAN drivers ctrlmode the provided new content has to
be checked whether the bits are allowed to be changed. The bits that are to be
changed are given as a bitfield in cm->mask. Therefore checking against
cm->flags is wrong as the content can hold any kind of values.
The iproute2 tool sets the bits in cm->mask and cm->flags depending on the
detected command line options. To be robust against bogus user space
applications additionally sanitize the provided flags with the provided mask.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e7e6e0c9b47a45576c38b4a72d67927a5e049f7 upstream.
Recent Leaf firmware versions (>= 3.1.557) do not allow to send
commands for non-existing channels. If a command is sent for a
non-existing channel, the firmware crashes.
Reported-by: Christopher Storah <Christopher.Storah@invetech.com.au>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 889b77f7fd2bcc922493d73a4c51d8a851505815 upstream.
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in very high frequency (*), closing the CAN channel while
all the transmissions are on (#), opening the device again (@),
then sending a small number of packets would make the driver
enter an almost infinite loop of:
[....]
[15959.853988] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853990] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853991] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853993] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853994] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853995] kvaser_usb 4-3:1.0 can0: cannot find free context
[....]
_dragging the whole system down_ in the process due to the
excessive logging output.
Initially, this has caused random panics in the kernel due to a
buggy error recovery path. That got fixed in an earlier commit.(%)
This patch aims at solving the root cause. -->
16 tx URBs and contexts are allocated per CAN channel per USB
device. Such URBs are protected by:
a) A simple atomic counter, up to a value of MAX_TX_URBS (16)
b) A flag in each URB context, stating if it's free
c) The fact that ndo_start_xmit calls are themselves protected
by the networking layers higher above
After grabbing one of the tx URBs, if the driver noticed that all
of them are now taken, it stops the netif transmission queue.
Such queue is worken up again only if an acknowedgment was received
from the firmware on one of our earlier-sent frames.
Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP
to the firmware, effectively closing all further communication. In
the high traffic case, the atomic counter remains at MAX_TX_URBS,
and all the URB contexts remain marked as active. While opening
the channel again (@), it cannot send any further frames since no
more free tx URB contexts are available.
Reset all tx URB contexts upon CAN channel close.
(*) 50 parallel instances of `cangen0 -g 0 -ix`
(#) `ifconfig can0 down`
(@) `ifconfig can0 up`
(%) "can: kvaser_usb: Don't free packets when tight on URBs"
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b442723fcec445fb0ae1104888dd22cd285e0a91 upstream.
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in high frequency caused seemingly-random panics in the
kernel.
On further inspection, it seems the driver erroneously freed the
to-be-transmitted packet upon getting tight on URBs and returning
NETDEV_TX_BUSY, leading to invalid memory writes and double frees
at a later point in time.
Note:
Finding no more URBs/transmit-contexts and returning NETDEV_TX_BUSY
is a driver bug in and out of itself: it means that our start/stop
queue flow control is broken.
This patch only fixes the (buggy) error handling code; the root
cause shall be fixed in a later commit.
Acked-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 17e96834fd35997ca7cdfbf15413bcd5a36ad448 ]
Hardware always provides compliment of IP pseudo checksum. Stack expects
whole packet checksum without pseudo checksum if CHECKSUM_COMPLETE is set.
This causes checksum error in nf & ovs.
kernel: qg-19546f09-f2: hw csum failure
kernel: CPU: 9 PID: 0 Comm: swapper/9 Tainted: GF O-------------- 3.10.0-123.8.1.el7.x86_64 #1
kernel: Hardware name: Cisco Systems Inc UCSB-B200-M3/UCSB-B200-M3, BIOS B200M3.2.2.3.0.080820141339 08/08/2014
kernel: ffff881218f40000 df68243feb35e3a8 ffff881237a43ab8 ffffffff815e237b
kernel: ffff881237a43ad0 ffffffff814cd4ca ffff8829ec71eb00 ffff881237a43af0
kernel: ffffffff814c6232 0000000000000286 ffff8829ec71eb00 ffff881237a43b00
kernel: Call Trace:
kernel: <IRQ> [<ffffffff815e237b>] dump_stack+0x19/0x1b
kernel: [<ffffffff814cd4ca>] netdev_rx_csum_fault+0x3a/0x40
kernel: [<ffffffff814c6232>] __skb_checksum_complete_head+0x62/0x70
kernel: [<ffffffff814c6251>] __skb_checksum_complete+0x11/0x20
kernel: [<ffffffff8155a20c>] nf_ip_checksum+0xcc/0x100
kernel: [<ffffffffa049edc7>] icmp_error+0x1f7/0x35c [nf_conntrack_ipv4]
kernel: [<ffffffff814cf419>] ? netif_rx+0xb9/0x1d0
kernel: [<ffffffffa040eb7b>] ? internal_dev_recv+0xdb/0x130 [openvswitch]
kernel: [<ffffffffa04c8330>] nf_conntrack_in+0xf0/0xa80 [nf_conntrack]
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffffa049e302>] ipv4_conntrack_in+0x22/0x30 [nf_conntrack_ipv4]
kernel: [<ffffffff815005ca>] nf_iterate+0xaa/0xc0
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffff81500664>] nf_hook_slow+0x84/0x140
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffff81509dd4>] ip_rcv+0x344/0x380
Hardware verifies IP & tcp/udp header checksum but does not provide payload
checksum, use CHECKSUM_UNNECESSARY. Set it only if its valid IP tcp/udp packet.
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Stefan Assmann <sassmann@redhat.com>
Reported-by: Sunil Choudhary <schoudha@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7a05dc64e2e4c611d89007b125b20c0d2a4d31a5 ]
Commit d75b1ade567f ("net: less interrupt masking in NAPI") uncovered
wrong alx_poll() behavior.
A NAPI poll() handler is supposed to return exactly the budget when/if
napi_complete() has not been called.
It is also supposed to return number of frames that were received, so
that netdev_budget can have a meaning.
Also, in case of TX pressure, we still have to dequeue received
packets : alx_clean_rx_irq() has to be called even if
alx_clean_tx_irq(alx) returns false, otherwise device is half duplex.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade567f ("net: less interrupt masking in NAPI")
Reported-by: Oded Gabbay <oded.gabbay@amd.com>
Bisected-by: Oded Gabbay <oded.gabbay@amd.com>
Tested-by: Oded Gabbay <oded.gabbay@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 05b0aa579397b734f127af58e401a30784a1e315 ]
During driver load in tg3_init_one, if the driver detects DMA activity before
intializing the chip tg3_halt is called. As part of tg3_halt interrupts are
disabled using routine tg3_disable_ints. This routine was using mailbox value
which was not initialized (default value is 0). As a result driver was writing
0x00000001 to pci config space register 0, which is the vendor id / device id.
This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only
the Vendor ID to identify Configuration Request Retry). Also this issue is only
seen in older generation chipsets like 5722 because config space write to offset
0 from driver is possible. The newer generation chips ignore writes to offset 0.
Also without commit a7877b17a667, for these older chips when a GRC reset is
issued the Bootcode would reprogram the vendor id/device id, which is the reason
this bug was masked earlier.
Fixed by initializing the interrupt mailbox registers before calling tg3_halt.
Please queue for -stable.
Reported-by: Nils Holland <nholland@tisys.org>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e4982f6a51a2442f1bb588fee42521b44b4531c upstream.
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc50ddcd4c58a5a0226038307d6ef884bec9f8c2 upstream.
This patchs fixes a misplaced call to memset() that fills the request
buffer with 0. The problem was with sending PCAN_USBPRO_REQ_FCT
requests, the content set by the caller was thus lost.
With this patch, the memory area is zeroed only when requesting info
from the device.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af35d0f1cce7a990286e2b94c260a2c2d2a0e4b0 upstream.
This patch sets the correct reverse sequence order to the instructions
set to run, when any failure occurs during the initialization steps.
It also adds the missing unregistration call of the can device if the
failure appears after having been registered.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78063d81d353e10cbdd279c490593113b8fdae1c upstream.
Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ad8fdccf9c197a89e2d2fa78c453283dcc2c343f upstream.
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Reported-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aec653c43b0c55667355e26d7de1236bda9fb4e3 upstream.
Call igb_setup_link() when the PHY is powered up.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aebea2ba0f7495e1a1c9ea5e753d146cb2f6b845 ]
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2d5c57d7fbfaa642fb7f0673df24f32b83d9066c ]
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a620a6bc1c94c22d6c312892be1e0ae171523125 ]
If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.
This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d609725d4357f499e2103e46011308b32f53513 upstream.
These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.
Fixes: f36c374782e4 ("xen/netfront: handle compound page fragments on transmit")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cfd9167af14eb4ec21517a32911d460083ee3d59 upstream.
RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.
For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.
Patch fixes skb_under_panic problems reported from time to time:
https://bugzilla.kernel.org/show_bug.cgi?id=84911
https://bugzilla.kernel.org/show_bug.cgi?id=72471
http://marc.info/?l=linux-wireless&m=139108549530402&w=2
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi>
Debugged-by: Antti S. Lankila <alankila@bel.fi>
Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5247a589c24022ab34e780039cc8000c48f2035e upstream.
ikfree_skb() is Called in can_free_echo_skb(), which might be called from (TX
Error) interrupt, which triggers the folloing warning:
[ 1153.360705] ------------[ cut here ]------------
[ 1153.360715] WARNING: CPU: 0 PID: 31 at net/core/skbuff.c:563 skb_release_head_state+0xb9/0xd0()
[ 1153.360772] Call Trace:
[ 1153.360778] [<c167906f>] dump_stack+0x41/0x52
[ 1153.360782] [<c105bb7e>] warn_slowpath_common+0x7e/0xa0
[ 1153.360784] [<c158b909>] ? skb_release_head_state+0xb9/0xd0
[ 1153.360786] [<c158b909>] ? skb_release_head_state+0xb9/0xd0
[ 1153.360788] [<c105bc42>] warn_slowpath_null+0x22/0x30
[ 1153.360791] [<c158b909>] skb_release_head_state+0xb9/0xd0
[ 1153.360793] [<c158be90>] skb_release_all+0x10/0x30
[ 1153.360795] [<c158bf06>] kfree_skb+0x36/0x80
[ 1153.360799] [<f8486938>] ? can_free_echo_skb+0x28/0x40 [can_dev]
[ 1153.360802] [<f8486938>] can_free_echo_skb+0x28/0x40 [can_dev]
[ 1153.360805] [<f849a12c>] esd_pci402_interrupt+0x34c/0x57a [esd402]
[ 1153.360809] [<c10a75b5>] handle_irq_event_percpu+0x35/0x180
[ 1153.360811] [<c10a7623>] ? handle_irq_event_percpu+0xa3/0x180
[ 1153.360813] [<c10a7731>] handle_irq_event+0x31/0x50
[ 1153.360816] [<c10a9c7f>] handle_fasteoi_irq+0x6f/0x120
[ 1153.360818] [<c10a9c10>] ? handle_edge_irq+0x110/0x110
[ 1153.360822] [<c1011b61>] handle_irq+0x71/0x90
[ 1153.360823] <IRQ> [<c168152c>] do_IRQ+0x3c/0xd0
[ 1153.360829] [<c1680b6c>] common_interrupt+0x2c/0x34
[ 1153.360834] [<c107d277>] ? finish_task_switch+0x47/0xf0
[ 1153.360836] [<c167c27b>] __schedule+0x35b/0x7e0
[ 1153.360839] [<c10a5334>] ? console_unlock+0x2c4/0x4d0
[ 1153.360842] [<c13df500>] ? n_tty_receive_buf_common+0x890/0x890
[ 1153.360845] [<c10707b6>] ? process_one_work+0x196/0x370
[ 1153.360847] [<c167c723>] schedule+0x23/0x60
[ 1153.360849] [<c1070de1>] worker_thread+0x161/0x460
[ 1153.360852] [<c1090fcf>] ? __wake_up_locked+0x1f/0x30
[ 1153.360854] [<c1070c80>] ? rescuer_thread+0x2f0/0x2f0
[ 1153.360856] [<c1074f01>] kthread+0xa1/0xc0
[ 1153.360859] [<c1680401>] ret_from_kernel_thread+0x21/0x30
[ 1153.360861] [<c1074e60>] ? kthread_create_on_node+0x110/0x110
[ 1153.360863] ---[ end trace 5ff83639cbb74b35 ]---
This patch replaces the kfree_skb() by dev_kfree_skb_any().
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efbd50d2f62fc1f69a3dcd153e63ba28cc8eb27f upstream.
It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds
the missing deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a5f6fc28d6e6cc379c6839f21820e62262419584 ]
pptp_getname() only partially initializes the stack variable sa,
particularly only fills the pptp part of the sa_addr union. The code
thereby discloses 16 bytes of kernel stack memory via getsockname().
Fix this by memset(0)'ing the union before.
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bb2bdeb83fb125c95e47fc7eca2a3e8f868e2a74 ]
Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e)
Signed-off-by: Martin Hauke <mardnh@gmx.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c2dd54485ccee7fc4086611e188478584758c8d ]
In case of any failure ieee802154fake_probe() just calls unregister_netdev().
But it does not look safe to unregister netdevice before it was registered.
The patch implements straightforward resource deallocation in case of
failure in ieee802154fake_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d4b646613d6b12175b017aca18113945af1faf3 upstream.
Fix a race between BlueFlame flow and stamping in post send flow.
Example:
SW: Build WQE 0 on the TX buffer, except the ownership bit
SW: Set ownership for WQE 0 on the TX buffer
SW: Ring doorbell for WQE 0
SW: Build WQE 1 on the TX buffer, except the ownership bit
SW: Set ownership for WQE 1 on the TX buffer
HW: Read WQE 0 and then WQE 1, before doorbell was rung/BF was done for WQE 1
HW: Produce CQEs for WQE 0 and WQE 1
SW: Process the CQEs, and stamp WQE 0 and WQE 1 accordingly (on the TX buffer)
SW: Copy WQE 1 from the TX buffer to the BF register - ALREADY STAMPED!
HW: CQE error with index 0xFFFF - the BF WQE's control segment is STAMPED,
so the BF index is 0xFFFF. Error: Invalid Opcode.
As a result QP enters the error state and no traffic can be sent.
Solution:
When stamping - do not stamp last completed wqe.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ce9b20f1971690b8b3b620e735ec99431573b39 upstream.
When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place. The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN tags are
detected.
Fixes: f09e2249c4f5 ("macvtap: restore vlan header on user read")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 9180ac50716a097a407c6d7e7e4589754a922260 upstream.
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d0aedcd4f14a22e23b313f42b7e6e6ebfc0fbc31 ]
vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.
The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.
Orabug: 19441666
OraBZ: 14983
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 664d6a792785cc677c2091038ce10322c8d04ae1 upstream.
0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle
References: https://bugs.debian.org/766802
Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24dff96a37a2ca319e75a74d3929b2de22447ca6 upstream.
we used to check for "nobody else could start doing anything with
that opened file" by checking that refcount was 2 or less - one
for descriptor table and one we'd acquired in fget() on the way to
wherever we are. That was race-prone (somebody else might have
had a reference to descriptor table and do fget() just as we'd
been checking) and it had become flat-out incorrect back when
we switched to fget_light() on those codepaths - unlike fget(),
it doesn't grab an extra reference unless the descriptor table
is shared. The same change allowed a race-free check, though -
we are safe exactly when refcount is less than 2.
It was a long time ago; pre-2.6.12 for ioctl() (the codepath leading
to ppp one) and 2.6.17 for sendmsg() (netlink one). OTOH,
netlink hadn't grown that check until 3.9 and ppp used to live
in drivers/net, not drivers/net/ppp until 3.1. The bug existed
well before that, though, and the same fix used to apply in old
location of file.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit de11b0e8c569b96c2cf6a811e3805b7aeef498a3 ]
These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled. However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: f43798c27684 ("tun: Allow GSO using virtio_net_hdr")
Fixes: b9fb9ee07e67 ("macvtap: add GSO/csum offload support")
Fixes: 5188cd44c55d ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 95ff88688781db2f64042e69bd499e518bbb36e5 ]
The following patch fixes a bug which causes the ax88179_178a driver to be
incapable of being added to a bond.
When I brought up the issue with the bonding maintainers, they indicated
that the real problem was with the NIC driver which must return zero for
success (of setting the MAC address). I see that several other NIC drivers
follow that pattern by either simply always returing zero, or by passing
through a negative (error) result while rewriting any positive return code
to zero. With that same philisophy applied to the ax88179_178a driver, it
allows it to work correctly with the bonding driver.
I believe this is suitable for queuing in -stable, as it's a small, simple,
and obvious fix that corrects a defect with no other known workaround.
This patch is against vanilla 3.17(.0).
Signed-off-by: Ian Morgan <imorgan@primordial.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 01f7feeaf4528bec83798316b3c811701bac5d3e upstream.
Two bits control TX power on BBP_R1 register. Correct the mask,
otherwise we clear additional bit on BBP_R1 register, what can have
unknown, possible negative effect.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f08970f5284dce486f0e2290834aefb2a262189 upstream.
Add 4 missing PCI IDs for the 7260 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dedb845ded56ded1c62f5398a94ffa8615d4592d ]
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Long Li <longli@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7d3083ee36b51e425b6abd76778a2046906b0fd3 ]
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 476c18850c6cbaa3f2bb661ae9710645081563b9 ]
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 10545937e866ccdbb7ab583031dbdcc6b14e4eb4 ]
On IOMMU systems DMA mapping can fail, we need to check for
that possibility.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c66517165610b911e4c6d268f28d8c640832dbd1 upstream.
The Sitecom WLA-2102 adapter uses this driver.
Reported-by: Nico Baggus <nico-linux@noci.xs4all.nl>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nico Baggus <nico-linux@noci.xs4all.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f47f46d7b09cf1d09e4b44b6cc4dd7d68a08028c upstream.
This reverts commit 43d826ca5979927131685cc2092c7ce862cb91cd.
This commit caused packet loss.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
