summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2013-09-26net: mvneta: properly disable HW PHY polling and ensure adjust_link() worksThomas Petazzoni
commit 714086029116b6b0a34e67ba1dd2f0d1cf26770c upstream. This commit fixes a long-standing bug that has been reported by many users: on some Armada 370 platforms, only the network interface that has been used in U-Boot to tftp the kernel works properly in Linux. The other network interfaces can see a 'link up', but are unable to transmit data. The reports were generally made on the Armada 370-based Mirabox, but have also been given on the Armada 370-RD board. The network MAC in the Armada 370/XP (supported by the mvneta driver in Linux) has a functionality that allows it to continuously poll the PHY and directly update the MAC configuration accordingly (speed, duplex, etc.). The very first versions of the driver submitted for review were using this hardware mechanism, but due to this, the driver was not integrated with the kernel phylib. Following reviews, the driver was changed to use the phylib, and therefore a software based polling. In software based polling, Linux regularly talks to the PHY over the MDIO bus, and sees if the link status has changed. If it's the case then the adjust_link() callback of the driver is called to update the MAC configuration accordingly. However, it turns out that the adjust_link() callback was not configuring the hardware in a completely correct way: while it was setting the speed and duplex bits correctly, it wasn't telling the hardware to actually take into account those bits rather than what the hardware-based PHY polling mechanism has concluded. So, in fact the adjust_link() callback was basically a no-op. However, the network happened to be working because on the network interfaces used by U-Boot for tftp on Armada 370 platforms because the hardware PHY polling was enabled by the bootloader, and left enabled by Linux. However, the second network interface not used for tftp (or both network interfaces if the kernel is loaded from USB, NAND or SD card) didn't had the hardware PHY polling enabled. This patch fixes this situation by: (1) Making sure that the hardware PHY polling is disabled by clearing the MVNETA_PHY_POLLING_ENABLE bit in the MVNETA_UNIT_CONTROL register in the driver ->probe() function. (2) Making sure that the duplex and speed selections made by the adjust_link() callback are taken into account by clearing the MVNETA_GMAC_AN_SPEED_EN and MVNETA_GMAC_AN_DUPLEX_EN bits in the MVNETA_GMAC_AUTONEG_CONFIG register. This patch has been tested on Armada 370 Mirabox, and now both network interfaces are usable after boot. [ Problem introduced by commit c5aff18 ("net: mvneta: driver for Marvell Armada 370/XP network unit") ] Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Jochen De Smet <jochen.armkernel@leahnim.org> Cc: Peter Sanford <psanford@nearbuy.io> Cc: Ethan Tuttle <ethan@ethantuttle.com> Cc: Chény Yves-Gael <yves@cheny.fr> Cc: Ryan Press <ryan@presslab.us> Cc: Simon Guinot <simon.guinot@sequanux.org> Cc: vdonnefort@lacie.com Acked-by: Jason Cooper <jason@lakedaemon.net> Tested-by: Vincent Donnefort <vdonnefort@gmail.com> Tested-by: Yves-Gael Cheny <yves@cheny.fr> Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-26ath9k: avoid accessing MRC registers on single-chain devicesFelix Fietkau
commit a1c781bb20ac1e03280e420abd47a99eb8bbdd3b upstream. They are not implemented, and accessing them might trigger errors Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-26ath9k: fix rx descriptor related race conditionFelix Fietkau
commit e96542e55a2aacf4bdeccfe2f17b77c4895b4df2 upstream. Similar to a race condition that exists in the tx path, the hardware might re-read the 'next' pointer of a descriptor of the last completed frame. This only affects non-EDMA (pre-AR93xx) devices. To deal with this race, defer clearing and re-linking a completed rx descriptor until the next one has been processed. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-26ath9k: always clear ps filter bit on new assocFelix Fietkau
commit 026d5b07c03458f9c0ccd19c3850564a5409c325 upstream. Otherwise in some cases, EAPOL frames might be filtered during the initial handshake, causing delays and assoc failures. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-26brcmsmac: Fix WARNING caused by lack of calls to dma_mapping_error()John W. Linville
commit 67d0cf50bd32b66eab709871714e55725ee30ce4 upstream. The driver fails to check the results of DMA mapping in twp places, which results in the following warning: [ 28.078515] ------------[ cut here ]------------ [ 28.078529] WARNING: at lib/dma-debug.c:937 check_unmap+0x47e/0x930() [ 28.078533] bcma-pci-bridge 0000:0e:00.0: DMA-API: device driver failed to check map error[device address=0x00000000b5d60d6c] [size=1876 bytes] [mapped as single] [ 28.078536] Modules linked in: bnep bluetooth vboxpci(O) vboxnetadp(O) vboxnetflt(O) vboxdrv(O) ipv6 b43 brcmsmac rtl8192cu rtl8192c_common rtlwifi mac802 11 brcmutil cfg80211 snd_hda_codec_conexant rng_core snd_hda_intel kvm_amd snd_hda_codec ssb kvm mmc_core snd_pcm snd_seq snd_timer snd_seq_device snd k8temp cordic joydev serio_raw hwmon sr_mod sg pcmcia pcmcia_core soundcore cdrom i2c_nforce2 i2c_core forcedeth bcma snd_page_alloc autofs4 ext4 jbd2 mbcache crc1 6 scsi_dh_alua scsi_dh_hp_sw scsi_dh_rdac scsi_dh_emc scsi_dh ata_generic pata_amd [ 28.078602] CPU: 1 PID: 2570 Comm: NetworkManager Tainted: G O 3.10.0-rc7-wl+ #42 [ 28.078605] Hardware name: Hewlett-Packard HP Pavilion dv2700 Notebook PC/30D6, BIOS F.27 11/27/2008 [ 28.078607] 0000000000000009 ffff8800bbb03ad8 ffffffff8144f898 ffff8800bbb03b18 [ 28.078612] ffffffff8103e1eb 0000000000000002 ffff8800b719f480 ffff8800b7b9c010 [ 28.078617] ffffffff824204c0 ffffffff81754d57 0000000000000754 ffff8800bbb03b78 [ 28.078622] Call Trace: [ 28.078624] <IRQ> [<ffffffff8144f898>] dump_stack+0x19/0x1b [ 28.078634] [<ffffffff8103e1eb>] warn_slowpath_common+0x6b/0xa0 [ 28.078638] [<ffffffff8103e2c1>] warn_slowpath_fmt+0x41/0x50 [ 28.078650] [<ffffffff8122d7ae>] check_unmap+0x47e/0x930 [ 28.078655] [<ffffffff8122de4c>] debug_dma_unmap_page+0x5c/0x70 [ 28.078679] [<ffffffffa04a808c>] dma64_getnextrxp+0x10c/0x190 [brcmsmac] [ 28.078691] [<ffffffffa04a9042>] dma_rx+0x62/0x240 [brcmsmac] [ 28.078707] [<ffffffffa0479101>] brcms_c_dpc+0x211/0x9d0 [brcmsmac] [ 28.078717] [<ffffffffa046d927>] ? brcms_dpc+0x27/0xf0 [brcmsmac] [ 28.078731] [<ffffffffa046d947>] brcms_dpc+0x47/0xf0 [brcmsmac] [ 28.078736] [<ffffffff81047dcc>] tasklet_action+0x6c/0xf0 --snip-- [ 28.078974] [<ffffffff813891bd>] SyS_sendmsg+0xd/0x20 [ 28.078979] [<ffffffff81455c24>] tracesys+0xdd/0xe2 [ 28.078982] ---[ end trace 6164d1a08148e9c8 ]--- [ 28.078984] Mapped at: [ 28.078985] [<ffffffff8122c8fd>] debug_dma_map_page+0x9d/0x150 [ 28.078989] [<ffffffffa04a9322>] dma_rxfill+0x102/0x3d0 [brcmsmac] [ 28.079001] [<ffffffffa047a13d>] brcms_c_init+0x87d/0x1100 [brcmsmac] [ 28.079010] [<ffffffffa046d851>] brcms_init+0x21/0x30 [brcmsmac] [ 28.079018] [<ffffffffa04786e0>] brcms_c_up+0x150/0x430 [brcmsmac] As the patch adds a new failure mechanism to dma_rxfill(). When I changed the comment at the start of the routine to add that information, I also polished the wording. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Brett Rudley <brudley@broadcom.com> Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com> Cc: Hante Meuleman <meuleman@broadcom.com> Cc: brcm80211-dev-list@broadcom.com Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-14mwifiex: do not create AP and P2P interfaces upon driver loadingBing Zhao
commit 1211c961170cedb21c30d5bb7e2033c8720b38db upstream. Bug 60747 - 1286:2044 [Microsoft Surface Pro] Marvell 88W8797 wifi show 3 interface under network https://bugzilla.kernel.org/show_bug.cgi?id=60747 This issue was also reported previously by OLPC and some folks from the community. There are 3 network interfaces with different types being created when mwifiex driver is loaded: 1. mlan0 (infra. STA) 2. uap0 (AP) 3. p2p0 (P2P_CLIENT) The Network Manager attempts to use all 3 interfaces above without filtering the managed interface type. As the result, 3 identical interfaces are displayed under network manager. If user happens to click on an entry under which its interface is uap0 or p2p0, the association will fail. Work around it by removing the creation of AP and P2P interfaces at driver loading time. These interfaces can be added with 'iw' or other applications manually when they are needed. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-30net: fec: fix time stamping logic after napi conversionRichard Cochran
Commit dc975382 "net: fec: add napi support to improve proformance" converted the fec driver to the napi model. However, that commit forgot to remove the call to skb_defer_rx_timestamp which is only needed in non-napi drivers. (The function napi_gro_receive eventually calls netif_receive_skb, which in turn calls skb_defer_rx_timestamp.) This patch should also be applied to the 3.9 and 3.10 kernels. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-28net: xilinx: fix memleakLibo Chen
decrease device_node refcount np1 in err case. Signed-off-by: Libo Chen <libo.chen@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-28net: usb: Add HP hs2434 device to ZLP exception tableRob Gardner
This patch adds another entry (HP hs2434 Mobile Broadband) to the list of exceptional devices that require a zero length packet in order to function properly. This list was added in commit 844e88f0. The hs2434 is manufactured by Sierra Wireless, who also produces the MC7710, which the ZLP exception list was created for in the first place. So hopefully it is just this one producer's devices that will need this workaround. Tested on a DM1-4310NR HP notebook, which does not function without this change. Signed-off-by: Rob Gardner <robmatic@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-28net: stmmac: fixed the pbl setting with DTByungho An
This patch fixed the pbl(programmable burst length) setting using DT. Even though the default pbl is 8, If there is no pbl property in device tree file, pbl is set 0 and it causes bandwidth degradation. Signed-off-by: Byungho An <bh74.an@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27bnx2x: Fix VF stats syncAriel Elior
Since the PF gathers statistics for the VF, when the VF is about to unload we must synchronize the release of its statistics buffer with the PF, so that no DMA operation will be made to that address after the buffer release. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27bnx2x: Fix VF memory leak unloadAriel Elior
Due to incorrect VF/PF conditions, when unloading a VF it will not release part of the memory it has previously allocated. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27bnx2x: Fix functionality of configuring vlan listAriel Elior
The check on return code of bnx2x_vfop_config_vlan0() would lead to error handling flow as the return value indicating an existing pending ramrod would be erroneously considered as an error. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27bnx2x: Fix move FP memory deallocationsYuval Mintz
If driver will fail to allocate all queues, it will shrink the number of queues and move the storage queue to its correct place (i.e., the last queue among the newly supported number). When changing the pointers of the new location of the FCoE queue, we need to pay special attention to the aggregations pointer - that memory is allocated during probe and released upon driver removal. Current implementation has 2 pointers pointing to the same chunk of allocated memory, meaning upon removal there will be two kfree() of the same chunk while the other won't be released. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27bnx2x: vf mark stats startedAriel Elior
Solve issue where no stats were being collected for VF devices due to missing configuration in the stats' atomic synchronization mechanism. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless John W. Linville says: ==================== This is one more set of fixes intended for the 3.11 stream... For the mac80211 bits, Johannes says: "I have three more patches for the 3.11 stream: Felix's fix for the fairly visible brcmsmac crash, a fix from Simon for an IBSS join bug I found and a fix for a channel context bug in IBSS I'd introduced." Along with those... Sujith Manoharan makes a minor change to not use a PLL hang workaroun for AR9550. This one-liner fixes a couple of bugs reported in the Red Hat bugzilla. Helmut Schaa addresses an ath9k_htc bug that mangles frame headers during Tx. This fix is small, tested by the bug reported and isolated to ath9k_htc. Stanislaw Gruszka reverts a recent iwl4965 change that broke rfkill notification to user space. Please let me know if there are problems! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27ps3_gelic: lower NAPI weightMichal Schmidt
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT") netif_napi_add() produces an error message if a NAPI poll weight greater than 64 is requested. GELIC_NET_NAPI_WEIGHT is defined to GELIC_NET_RX_DESCRIPTORS, which is 128. Use the standard NAPI weight. v2: proper reference to the related commit Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Acked-by: Geoff Levand <geoff@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27netxen: lower NAPI weightMichal Schmidt
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT") netif_napi_add() produces an error message if a NAPI poll weight greater than 64 is requested. Use the standard NAPI weight. v2: proper reference to the related commit Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27jme: lower NAPI weightMichal Schmidt
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT") netif_napi_add() produces an error message if a NAPI poll weight greater than 64 is requested. jme requests a quarter of the rx ring size as the NAPI weight. jme's rx ring size is 1 << 9 = 512. Use the standard NAPI weight. v2: proper reference to the related commit Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-26be2net: Check for POST state in suspend-resume sequenceSarveshwar Bandi
In suspend-resume sequence, the OS could attempt to initialize the controller before it is ready, check for POST state before going ahead. Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-23Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2013-08-22be2net: fix disabling TX in be_close()Sathya Perla
commit fba875591 ("disable TX in be_close()") disabled TX in be_close() to protect be_xmit() from touching freed up queues in the AER recovery flow. But, TX must be disabled *before* cleaning up TX completions in the close() path, not after. This allows be_tx_compl_clean() to free up all TX-req skbs that were notified to the HW. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-22Merge branch 'sfc-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfcDavid S. Miller
Merge in a fix for RX MAC address filter programming bug in the sfc driver. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-22ath9k: Enable PLL fix only for AR9340/AR9330Sujith Manoharan
The PLL hang workaround is required only for AR9330 and AR9340. This issue was first observed on an AP121 and the WAR is enabled for AR9340 also (DB120 etc.), since it uses a PLL design identical to AR9330. This is not required for AR9485 and AR9550. Various bugs have been reported regarding this: https://bugzilla.redhat.com/show_bug.cgi?id=997217 https://bugzilla.redhat.com/show_bug.cgi?id=994648 Cc: stable@vger.kernel.org Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-22ath9k_htc: Restore skb headroom when returning skb to mac80211Helmut Schaa
ath9k_htc adds padding between the 802.11 header and the payload during TX by moving the header. When handing the frame back to mac80211 for TX status handling the header is not moved back into its original position. This can result in a too small skb headroom when entering ath9k_htc again (due to a soft retransmission for example) causing an skb_under_panic oops. Fix this by moving the 802.11 header back into its original position before returning the frame to mac80211 as other drivers like rt2x00 or ath5k do. Reported-by: Marc Kleine-Budde <mkl@blackshift.org> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Tested-by: Marc Kleine-Budde <mkl@blackshift.org> Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-22iwl4965: fix rfkill set state regressionStanislaw Gruszka
My current 3.11 fix: commit 788f7a56fce1bcb2067b62b851a086fca48a0056 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Thu Aug 1 12:07:55 2013 +0200 iwl4965: reset firmware after rfkill off broke rfkill notification to user-space . I missed that bug, because I compiled without CONFIG_RFKILL, sorry about that. Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-22Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
2013-08-21hso: Fix stack corruption on some architecturesDaniel Gimpelevich
As Sergei Shtylyov explained in the #mipslinux IRC channel: [Mon 2013-08-19 12:28:21 PM PDT] <headless> guys, are you sure it's not "DMA off stack" case? [Mon 2013-08-19 12:28:35 PM PDT] <headless> it's a known stack corruptor on non-coherent arches [Mon 2013-08-19 12:31:48 PM PDT] <DonkeyHotei> headless: for usb/ehci? [Mon 2013-08-19 12:34:11 PM PDT] <DonkeyHotei> headless: explain [Mon 2013-08-19 12:35:38 PM PDT] <headless> usb_control_msg() (or other such func) should not use buffer on stack. DMA from/to stack is prohibited [Mon 2013-08-19 12:35:58 PM PDT] <headless> and EHCI uses DMA on control xfers (as well as all the others) Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-21hso: Earlier catch of error conditionDaniel Gimpelevich
There is no need to get an interface specification if we know it's the wrong one. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-21sfc: Fix lookup of default RX MAC filters when steered using ethtoolBen Hutchings
commit 385904f819e3 ('sfc: Don't use efx_filter_{build,hash,increment}() for default MAC filters') used the wrong name to find the index of default RX MAC filters at insertion/ update time. This could result in memory corruption and would in any case silently fail to update the filter. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
2013-08-21mac80211: add a flag to indicate CCK support for HT clientsFelix Fietkau
brcm80211 cannot handle sending frames with CCK rates as part of an A-MPDU session. Other drivers may have issues too. Set the flag in all drivers that have been tested with CCK rates. This fixes a reported brcmsmac regression introduced in commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6 "mac80211/minstrel_ht: fix cck rate sampling" Cc: stable@vger.kernel.org # 3.10 Reported-by: Tom Gundersen <teg@jklm.no> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-20Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless John W. Linville says: ==================== Regarding the iwlwifi bits, Johannes says: "We revert an rfkill bugfix that unfortunately caused more bugs, shuffle some code to avoid touching the PCIe device before it's enabled and disconnect if firmware fails to do our bidding. I also have Stanislaw's fix to not crash in some channel switch scenarios." As for the mac80211 bits, Johannes says: "This time, I have one fix from Dan Carpenter for users of nl80211hdr_put(), and one fix from myself fixing a regression with the libertas driver." Along with the above... Dan Carpenter fixes some incorrectly placed "address of" operators in hostap that caused copying of junk data. Jussi Kivilinna corrects zd1201 to use an allocated buffer rather than the stack for a URB operation. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20net: phy: rtl8211: fix interrupt on status link changeGiuseppe CAVALLARO
This is to fix a problem in the rtl8211 where the driver wasn't properly enabled the interrupt on link change status. it has to enable the ineterrupt on the bit 10 in the register 18 (INER). Reported-by: Sharma Bhupesh <B45370@freescale.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20r8169: remember WOL preferences on driver loadPeter Wu
Do not clear Broadcast/Multicast/Unicast Wake Flag or LanWake in Config5. This is necessary to preserve WOL state when the driver is loaded. Although the r8168 vendor driver does not write Config5 (it has been commented out), Hayes Wang from Realtek said that masking bits like this is more sensible. Signed-off-by: Peter Wu <lekensteyn@gmail.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20via-ircc: don't return zero if via_ircc_open() failedAlexey Khoroshilov
If via_ircc_open() fails, data structures of the driver left uninitialized, but probe (via_init_one()) returns zero. That can lead to null pointer dereference in via_remove_one(), since it does not check drvdata for NULL. The patch implements proper error code propagation. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20macvtap: Ignore tap features when VNET_HDR is offVlad Yasevich
When the user turns off VNET_HDR support on the macvtap device, there is no way to provide any offload information to the user. So, it's safer to ignore offload setting then depend on the user setting them correctly. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20macvtap: Correctly set tap features when IFF_VNET_HDR is disabled.Vlad Yasevich
When the user turns off IFF_VNET_HDR flag, attempts to change offload features via TUNSETOFFLOAD do not work. This could cause GSO packets to be delivered to the user when the user is not prepared to handle them. To solve, allow processing of TUNSETOFFLOAD when IFF_VNET_HDR is disabled. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20macvtap: simplify usage of tap_featuresVlad Yasevich
In macvtap, tap_features specific the features of that the user has specified via ioctl(). If we treat macvtap as a macvlan+tap then we could all the tap a pseudo-device and give it other features like SG and GSO. Then we can stop using the features of lower device (macvlan) when forwarding the traffic the tap. This solves the issue of possible checksum offload mismatch between tap feature and macvlan features. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20bnx2x: set VF DMAE when first function has 0 supported VFsAriel Elior
There are possible HW configurations in which PFs will have SR-IOV capability but will have Max VFs set to 0 - this happens when there are Multi-Function devices where the VFs are allocated to only some of the PFs. DMAE is configured to support VFs only if the configuring PF has supported VFs. In case the first PF to be loaded will be one without supported VFs, it will not configure DMAE to the VF-supporting mode. When VFs of other PFs will be loaded later on, they will not be able to communicate with their PF. This changes the requirement for configuring DMAE for VF-supporting mode; If the device has SR-IOV capabilities there must be some PF that has max supported VFs > 0, thus it will configure the DMAE for supporting VFs. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20bnx2x: Protect against VFs' ndos when SR-IOV is disabledAriel Elior
Since SR-IOV can be activated dynamically and iproute2 can be called asynchronously, the various callbacks need a robust sanity check before attempting to access the SR-IOV database and members since there are numerous states in which it can find the driver (e.g., PF is down, sriov was not enabled yet, VF is down, etc.). In many of the states the callback result will be null pointer dereference. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20bnx2x: prevent VF benign attentionsYuval Mintz
During probe, VFs might erroneously try to access the shared memory (which only PFs are capabale of accessing), causing benign attentions to appear. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20bnx2x: Consider DCBX remote errorDmitry Kravkov
When publishing information via getfeatcfg(), bnx2x driver didn't consider remote errors (e.g., switch that doesn't support DCBX) when setting the error flags. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20bnx2x: Change DCB context handlingDmitry Kravkov
After notification that DCBX configuration has ended arrived to the driver, the driver configured the FW/HW in sleepless context. As a result, it was possible to reach a race (mostly with CNIC registration) in which the configuration will return a timeout, failing to set the DCBX results correctly. This patch moves the configuration following the DCBX end into the slowpath RTNL task (i.e., sleepless context protected by the RTNL lock), allowing the configuration to cope with such races. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-20bnx2x: dropless flow control not always functionalDmitry Kravkov
Since commit 3deb816 "bnx2x: Add a periodic task for link PHY events" link state changes can be detected not only via the attention flow but also from the periodic task. If the link state will change in such a manner (i.e., via the periodic task), dropless flow-control will not be configured. This patch remedies the issue, adding the missing configuration to all required flows. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-19Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2013-08-15net/mlx5_core: Support MANAGE_PAGES and QUERY_PAGES firmware command changesMoshe Lazer
In the previous QUERY_PAGES command version we used one command to get the required amount of boot, init and post init pages. The new version uses the op_mod field to specify whether the query is for the required amount of boot, init or post init pages. In addition the output field size for the required amount of pages increased from 16 to 32 bits. In MANAGE_PAGES command the input_num_entries and output_num_entries fields sizes changed from 16 to 32 bits and the PAS tables offset changed to 0x10. In the pages request event the num_pages field also changed to 32 bits. In the HCA-capabilities-layout the size and location of max_qp_mcg field has been changed to support 24 bits. This patch isn't compatible with firmware versions < 5; however, it turns out that the first GA firmware we will publish will not support previous versions so this should be OK. Signed-off-by: Moshe Lazer <moshel@mellanox.com> Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-15tun: signedness bug in tun_get_user()Dan Carpenter
The recent fix d9bf5f1309 "tun: compare with 0 instead of total_len" is not totally correct. Because "len" and "sizeof()" are size_t type, that means they are never less than zero. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-15qlcnic: Fix diagnostic interrupt test for 83xx adaptersManish Chopra
o Do not allow interrupt test when adapter is resetting. Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-15qlcnic: Fix beacon state return status handlingSucheta Chakraborty
o Driver was misinterpreting the return status for beacon state query leading to incorrect interpretation of beacon state and logging an error message for successful status. Fixed the driver to properly interpret the return status. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-15qlcnic: Fix set driver version commandHimanshu Madhani
Driver was issuing set driver version command through all functions in the adapter. Fix the driver to issue set driver version once per adapter, through function 0. Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2026-05-23 13:29:57 +0000