| Age | Commit message (Collapse) | Author |
|---|
|
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
|
|
Pull TTY/serial patches from Greg KH:
"tty and serial merge for 3.4-rc1
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty
layer, and a number of patches from Alan to help try to wrestle the vt
layer into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog."
* tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (132 commits)
serial: pxa: add clk_prepare/clk_unprepare calls
TTY: Wrong unicode value copied in con_set_unimap()
serial: PL011: clear pending interrupts
serial: bfin-uart: Don't access tty circular buffer in TX DMA interrupt after it is reset.
vt: NULL dereference in vt_do_kdsk_ioctl()
tty: serial: vt8500: fix annotations for probe/remove
serial: remove back and forth conversions in serial_out_sync
serial: use serial_port_in/out vs serial_in/out in 8250
serial: introduce generic port in/out helpers
serial: reduce number of indirections in 8250 code
serial: delete useless void casts in 8250.c
serial: make 8250's serial_in shareable to other drivers.
serial: delete last unused traces of pausing I/O in 8250
pch_uart: Add module parameter descriptions
pch_uart: Use existing default_baud in setup_console
pch_uart: Add user_uartclk parameter
pch_uart: Add Fish River Island II uart clock quirks
pch_uart: Use uartclk instead of base_baud
mpc5200b/uart: select more tolerant uart prescaler on low baudrates
tty: moxa: fix bit test in moxa_start()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches for 3.4-rc1 from Greg KH:
"Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink
breakage reverted), dynamic debugging updates, w1 drivers, hyperv
driver updates, and a variety of other bits and pieces, full
information in the shortlog."
* tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (78 commits)
Tools: hv: Support enumeration from all the pools
Tools: hv: Fully support the new KVP verbs in the user level daemon
Drivers: hv: Support the newly introduced KVP messages in the driver
Drivers: hv: Add new message types to enhance KVP
regulator: Support driver probe deferral
Revert "sysfs: Kill nlink counting."
uevent: send events in correct order according to seqnum (v3)
driver core: minor comment formatting cleanups
driver core: move the deferred probe pointer into the private area
drivercore: Add driver probe deferral mechanism
DS2781 Maxim Stand-Alone Fuel Gauge battery and w1 slave drivers
w1_bq27000: Only one thread can access the bq27000 at a time.
w1_bq27000 - remove w1_bq27000_write
w1_bq27000: remove unnecessary NULL test.
sysfs: Fix memory leak in sysfs_sd_setsecdata().
intel_idle: Revert change of auto_demotion_disable_flags for Nehalem
w1: Fix w1_bq27000
driver-core: documentation: fix up Greg's email address
powernow-k6: Really enable auto-loading
powernow-k7: Fix CPU family number
...
|
|
ZTE have yet to discover the magic of USB descriptors. These
devices use ff/ff/ff for class/subclass/protocol regardless of
function, except for usb-storage. Use an interface number
whitelist to force the driver to bind only to the QMI/wwan
interface.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.
In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.
In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK
Also increments tx_dropped counter
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.
This is mostly a revert of commit bf769375c (staging: hv: fix the return
status of netvsc_start_xmit())
In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.
In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
network drivers should reserve some headroom on incoming skbs so that we
dont need expensive reallocations, eg forwarding packets in tunnels.
This NET_SKB_PAD padding is done in various helpers, like
__netdev_alloc_skb_ip_align() in this patch, combining NET_SKB_PAD and
NET_IP_ALIGN magic.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When cycling the interface down and up, bnx2x_init_firmware() knows that
the firmware is already loaded, but nevertheless it allocates certain
arrays anew (init_data, init_ops, init_ops_offsets, iro_arr). The old
arrays are leaked.
Fix the leaks by returning early if the firmware was already loaded.
Because if the firmware is loaded, so are the arrays.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the requested firmware is deemed corrupt and then released, reset the
pointer to NULL in order to avoid double-freeing it in
bnx2x_release_firmware() or dereferencing it in bnx2x_init_firmware().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
v3: added previously removed sock_put() to the tun_release() callback, because
sk_release_kernel() doesn't drop the socket reference.
v2: sk_release_kernel() used for socket release. Dummy tun_release() is
required for sk_release_kernel() ---> sock_release() ---> sock->ops->release()
call.
TUN was designed to destroy it's socket on network namesapce shutdown. But this
will never happen for persistent device, because it's socket holds network
namespace.
This patch removes of holding network namespace by TUN socket and replaces it
by creating socket in init_net and then changing it's net it to desired one. On
shutdown socket is moved back to init_net prior to final put.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FCoE statistics ids were distinguished from the L2's statistics ids.
However, not all of the change was committed. This causes a possible
collision of indices when FCoE is present.
This patch fixes the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DCB flags were updated using the flags' bit offsets instead of
the actual bits. This is now fixed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed endianess issue when passing arguments to FW.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When pfc statistics were counted, the delta change from last count
was summed twice. This fixes the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Is possible that we stop queue and then do not wake up it again,
especially when packets are transmitted fast. That can be easily
reproduced with modified tx queue entry_num to some small value e.g. 16.
If mac80211 already hold local->queue_stop_reason_lock, then we can wait
on that lock in both rt2x00queue_pause_queue() and
rt2x00queue_unpause_queue(). After drooping ->queue_stop_reason_lock
is possible that __ieee80211_wake_queue() will be performed before
__ieee80211_stop_queue(), hence we stop queue and newer wake up it
again.
Another race condition is possible when between rt2x00queue_threshold()
check and rt2x00queue_pause_queue() we will process all pending tx
buffers on different cpu. This might happen if for example interrupt
will be triggered on cpu performing rt2x00mac_tx().
To prevent race conditions serialize pause/unpause by queue->tx_lock.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On il3945_down procedure we free tx queue data and nullify il->txq
pointer. After that we drop mutex and then cancel delayed works. There
is possibility, that after drooping mutex and before the cancel, some
delayed work will start and crash while trying to send commands to
the device. For example, here is reported crash in
il3945_bg_reg_txpower_periodic():
https://bugzilla.kernel.org/show_bug.cgi?id=42766#c10
Patch fix problem by adding il->txq check on works that send commands,
hence utilize tx queue.
Reported-by: Clemens Eisserer <linuxhippy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip.
Added USB id to find correct driver for AX88178 1000 Ethernet adapter.
Signed-off-by: Joerg Neikes <j.neikes@midlandgate.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding the Pantech UML290 and all non-QDL Gobi device IDs from the
qcserial driver now that we have support for shared net/QMI USB
interfaces. Most of these are not yet tested with this driver, but
should be mostly identical to tested devices, except for device IDs.
Gobi devices provide several different interfaces (serial/net/other)
using the exact same class, subclass and protocol values. This driver
will only support the net/QMI function while there are other drivers
supporting other device functions. The net/QMI interface number may
also differ from device to device. It has been noted that all the
other interfaces have additional functional descriptors, so we use that
to detect the interface supported by this driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the new cdc-wdm subdriver interface to create a device management
device even for USB devices having a single combined QMI/wwan USB
interface with three endpoints (int, bulk in, bulk out) instead of
separate data and control interfaces.
Some Huawei devices can be switched to a single interface mode for
use with other operating systems than Linux. This adds support
for these devices when they run in such non-Linux modes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces. The Huawei E392/E398 are examples of such devices.
These typically cannot be fully configured using AT commands
over a serial interface. It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.
The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function. This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.
Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver. To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.
You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This was done to resolve a conflict in the drivers/base/cpu.c file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <olaf@aepfle.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Again, no need to do that from the pci probe function.
Hmm, I noticed this driver is marked as BROKEN. Won't touch it more,
it has to be converted to dynamic tty driver allocation first.
Perhaps it is time to move it to staging?
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
They are in .bss which is initialized to zeros when the module is
loaded/kernel booted.
What a strange way to do the initialization once in the pci probe
routine...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|kernel BUG at kernel/rtmutex.c:724!
|[<c029599c>] (rt_spin_lock_slowlock+0x108/0x2bc) from [<c01c2330>] (defer_bh+0x1c/0xb4)
|[<c01c2330>] (defer_bh+0x1c/0xb4) from [<c01c3afc>] (rx_complete+0x14c/0x194)
|[<c01c3afc>] (rx_complete+0x14c/0x194) from [<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0)
|[<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0) from [<c01e1ff4>] (musb_giveback+0x34/0x40)
|[<c01e1ff4>] (musb_giveback+0x34/0x40) from [<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0)
|[<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0) from [<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c)
|[<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c) from [<c01e2ed0>] (musb_urb_dequeue+0xec/0x108)
|[<c01e2ed0>] (musb_urb_dequeue+0xec/0x108) from [<c01cbb90>] (unlink1+0xbc/0xcc)
|[<c01cbb90>] (unlink1+0xbc/0xcc) from [<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8)
|[<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8) from [<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58)
|[<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58) from [<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c)
|[<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c) from [<c01c2d68>] (usbnet_stop+0x100/0x15c)
|[<c01c2d68>] (usbnet_stop+0x100/0x15c) from [<c020f718>] (__dev_close_many+0x94/0xc8)
defer_bh() takes the lock which is hold during unlink_urbs(). The safe
walk suggest that the skb will be removed from the list and this is done
by defer_bh() so it seems to be okay to drop the lock here.
Cc: stable@kernel.org
Reported-by: AnÃbal Almeida Pinto <anibal.pinto@efacec.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The actual FW command is called in procedure "handle_resize".
Code incorrectly invoked the FW command again (in good flow), in
the modify_cq wrapper function.
Fix by skipping second FW invocation unconditionally for resize.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop. The
intent was to set the zero bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 239c562c94d (ehea: Add 64bit statistics) added a regression,
since we no longer report multicast & rx_errors fields, taken from
port->stats structure. These fields are updated in ehea_update_stats()
every second.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
Default MTU for CAIF HSI was wrongly set to 15 * 4092 bytes.
The patch sets default MTU size to 4096.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes a bug introduced by commit fe9a2603c, where the priority bits
in the schedule queue field were masked out.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With runtime PM, if the ethernet cable is disconnected, the device is
transitioned to D3 state to conserve energy. If the system is shutdown
in this state, any register accesses in rtl_shutdown are dropped on
the floor. As the device was programmed by .runtime_suspend() to wake
on link changes, it is thus brought back up as soon as the link recovers.
Resuming every suspended device through the driver core would slow things
down and it is not clear how many devices really need it now.
Original report and D0 transition patch by Sameer Nanda. Patch has been
changed to comply with advices by Rafael J. Wysocki and the PM folks.
Reported-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Fix tg3 to use BQL multi queue related netdev interfaces since the
device supports multi queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Reported-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In 'ql_adapter_initialize'
the first call for 'spin_unlock_irqrestore()' is with hw_flags = 0,
which is as good as 'spin_unlock_irq()' (unconditional interrupt
enabling). If this is intended, then for better performance
'spin_unlock_irqrestore()' can be replaced with 'spin_unlock_irq()'
and 'spin_lock_irqsave()' can be replaced by 'spin_lock_irq()
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was broken by the commit 023ca58f1
"iwlwifi: Move the core suspend function to iwl-agn-lib"
where for some reason the code changed while moving,
from
.len[0] = sizeof(*key_data.rsc_tsc),
to
.len[0] = sizeof(key_data.rsc_tsc),
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Noticed with the 8168d (-vb-gr, aka RTL_GIGA_MAC_VER_26).
ConfigX registers should only be written while the Config9346 lock
is held.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the big network driver reorg, each vendor directory defaults to
yes, so that older config's can migrate correctly. Looks like this one
got missed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix transport header size
Fix the transpoert header size for UDP packets.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"num_vfs" is a u32 but we only use the high 16 bits and the low 16bits
are left as zero. That isn't a problem for little endian systems but it
will break on big endian ones.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pch_gbe_validate_option() modifies 32 bits of memory but we pass
&hw->phy.autoneg_advertised which only has 16 bits and &hw->mac.fc
which only has 8 bits.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3_get_stats64() takes tp->lock when dealing with non-serdes bcm5700
and bcm5701 devices. However, functions that call tg3_halt() have
already acquired tp->lock. When tg3_get_stats64() is called in
tg3_halt(), deadlock will occur.
This patch fixes the problem by separating the stat gathering code into
a new tg3_get_nstats() function. tg3_get_stats64() is recoded to call
this function and take tp->lock. The code that takes tp->lock in
tg3_calc_crc_errors() has been removed. Function signatures have been
cleaned up too.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent commit
"mwifiex: clear previous security setting during association"
fixes association failure problems observed in some corner cases
by clearing previous security setting before each association.
We should reset encryption mode flag as well. This patch takes care
of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Nicolas Cavallari discovered that carl9170 has some
serious problems delivering data to sleeping stations.
It turns out that the driver was not honoring two
important flags (IEEE80211_TX_CTL_POLL_RESPONSE and
IEEE80211_TX_CTL_CLEAR_PS_FILT) which are set on
frames that should be sent although the receiving
station is still in powersave mode.
Cc: stable <stable@vger.kernel.org>
Reported-by: Nicolas Cavallari <Nicolas.Cavallari@lri.fr>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On Access Point mode, when transmitting a packet, if the destination
station is in powersave mode, we abort transmitting the packet to the
device queue, but we do not reclaim the allocated memory. Given enough
packets, we can go in a state where there is no packet on the device
queue, but we think the device has no memory left, so no packet gets
transmitted, connections breaks and the AP stops working.
This undo the allocation done in the TX path when the station is in
power-save mode.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
