Age | Commit message (Collapse) | Author |
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
net: Fix routing tables with id > 255 for legacy software
sky2: Hold RTNL while calling dev_close()
s2io iomem annotations
atl1: fix suspend regression
qeth: start dev queue after tx drop error
qeth: Prepare-function to call s390dbf was wrong
qeth: reduce number of kernel messages
qeth: Use ccw_device_get_id().
qeth: layer 3 Oops in ip event handler
virtio: use callback on empty in virtio_net
virtio: virtio_net free transmit skbs in a timer
virtio: Fix typo in virtio_net_hdr comments
virtio_net: Fix skb->csum_start computation
ehea: set mac address fix
sfc: Recover from RX queue flush failure
add missing lance_* exports
ixgbe: fix typo
forcedeth: msi interrupts
ipsec: pfkey should ignore events when no listeners
pppoe: Unshare skb before anything else
...
|
|
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
dev_close() must be called holding the RTNL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Using vendor magic to force the PHY into power save mode breaks
suspend. It isn't needed anyway, so remove it.
Tested-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
virtio_net uses a timer to free old transmitted packets, rather than
leaving callbacks enabled all the time. If the host promises to
always notify us when the transmit ring is empty, we can free packets
at that point and avoid the timer.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
virtio_net currently only frees old transmit skbs just
before queueing new ones. If the queue is full, it then
enables interrupts and waits for notification that more
work has been performed.
However, a side-effect of this scheme is that there are
always xmit skbs left dangling when no new packets are
sent, against the Documentation/networking/driver.txt
guideline:
"... it is not allowed for your TX mitigation scheme
to let TX packets "hang out" in the TX ring unreclaimed
forever if no new TX packets are sent."
Add a timer to ensure that any time we queue new TX
skbs, we will shortly free them again.
This fixes an easily reproduced hang at shutdown where
iptables attempts to unload nf_conntrack and nf_conntrack
waits for an skb it is tracking to be freed, but virtio_net
never frees it.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
hdr->csum_start is the offset from the start of the ethernet
header to the transport layer checksum field. skb->csum_start
is the offset from skb->head.
skb_partial_csum_set() assumes that skb->data points to the
ethernet header - i.e. it computes skb->csum_start by adding
the headroom to hdr->csum_start.
Since eth_type_trans() skb_pull()s the ethernet header,
skb_partial_csum_set() should be called before
eth_type_trans().
(Without this patch, GSO packets from a guest to the world outside the
host are corrupted).
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
eHEA has to call firmware functions in order to change the mac address
of a logical port. This patch checks if the logical port is up
when calling the register / deregister mac address calls. If the port
is down these firmware calls would fail and are therefore not executed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
RX queue flush can fail if traffic continues to arrive. Recover by
performing an invisible reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch fixes the following build error:
<-- snip -->
...
Building modules, stage 2.
MODPOST 1203 modules
ERROR: "lance_open" [drivers/net/mvme147.ko] undefined!
ERROR: "lance_close" [drivers/net/mvme147.ko] undefined!
ERROR: "lance_tx_timeout" [drivers/net/mvme147.ko] undefined!
ERROR: "lance_set_multicast" [drivers/net/mvme147.ko] undefined!
ERROR: "lance_start_xmit" [drivers/net/mvme147.ko] undefined!
...
make[2]: *** [__modpost] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Define names were accidently transposed.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add a workaround for lost MSI interrupts. There is a race condition in
the HW in which future interrupts could be missed. The workaround is to
toggle the MSI irq mask.
Added cleanup based on comments from Andrew Morton.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
We need to unshare the skb first as otherwise pskb_may_pull may
write to a shared skb which could be bad.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The length field in the PPPOE header wasn't checked completely.
This patch causes all packets shorter than the declared length
to be dropped.
It also changes the memcpy_toiovec call to skb_copy_datagram_iovec
so that paged packets (rare for PPPOE) are handled properly.
Thanks to Ilja of the Netric Security Team for discovering and
reporting this bug, and Chris Wright for the total_len check.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a potential memory corruption in
pppol2tp_recvmsg(). If skb->len is bigger than the caller's buffer
length, memcpy_toiovec() will go into unintialized data on the kernel
heap, interpret it as an iovec and start modifying memory.
The fix is to change the memcpy_toiovec() call to
skb_copy_datagram_iovec() so that paged packets (rare for PPPOL2TP)
are handled properly. Also check that the caller's buffer is big
enough for the data and set the MSG_TRUNC flag if it is not so.
Reported-by: Ilja <ilja@netric.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
-tip testing found the following build error:
drivers/built-in.o: In function `mcs_receive_irq':
mcs7780.c:(.text+0x4e429): undefined reference to `crc32_le'
drivers/built-in.o: In function `mcs_hard_xmit':
mcs7780.c:(.text+0x4e9af): undefined reference to `crc32_le'
with:
http://redhat.com/~mingo/misc/config-Sun_Jun__8_22_56_14_CEST_2008.bad
the reason is a missing enablement of the CRC32 library in the Kconfig.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch increments the version to 3.92.1.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 5761 non-e devices, two problems prevent the administrator from
overriding the WOL settings in the device's NVRAM.
The first problem is that GPIO 0 and GPIO 2 have been swapped. This
change prevented the administrator from turning on WOL when it is
disabled in NVRAM. The fix is to add a new path for the 5761 that
swaps the two GPIOs in the code as well.
The second problem is that GPIO 1 could not be toggled by the driver
because the GPIO is shared with the debug UART GPIO. This will prevent
the administrator from being able to turn WOL off if it was enabled in
NVRAM. The fix is to always disable the debug UART after a GRC reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a problem where the TG3_FLAG_10_100_ONLY flag was
testing against the wrong flags variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The git commit ef167e27039eeaea6d3cdd5c547b082e89840bdd entitled
"Fix supporting flowctrl code" introduced a bug that prevents 5714S,
5715S and 5780S devices from falling back to a forced link mode. The
problem is that the added flow control check will always fail if flow
control is set to autoneg and either RX or TX (or both) flow control
is enabled. The driver defaults to setting flow control to autoneg
and advertises both RX and TX flow control.
The fix is to remove the errant check.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix race between:
ieee80211_open->ieee80211_led_radio->led_trigger_event->led_set_brightness->iwl3945_led_brightness_set
(which assumes that "led->priv" is not NULL)
and
iwl3945_pci_probe->iwl3945_setup_deferred_work->(...)->iwl3945_bg_alive_start->iwl3945_alive_start->iwl3945_led_register->iwl3945_led_register_led
which sets priv field in struct iwl3945_led
after
led->led_dev.brightness_set = iwl3945_led_brightness_set;
(...)
led_classdev_register(device, &led->led_dev);
http://kerneloops.org/guilty.php?guilty=iwl3945_led_brightness_set&version=2.6.25-release&start=1671168&end=1703935&class=oops
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: ipw3945-devel@lists.sourceforge.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a data alignment issue in the zd1211rw driver.
The IEEE80211_STYPE_QOS_DATA bit should be used as a bitwise test
to test for the presence of the 2 byte QoS control field.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes an issus that made "iwconfig eth1 power on" non-working.
When we get a "PS sleep" event, we have to confirm this to the firmware.
The confirm happens with a command, but this command is special: the
firmware won't send us a response. if_cs_host_to_card() is setting
priv->dnld_sent anyway, so this variable stayed at DNLD_DATA_SENT and
was never cleared back.
Now I put the special knowledge that the CMD_802_11_PS_MODE with
CMD_SUBCMD_SLEEP_CONFIRMED doesn't need to need a response by directly
clearing the dnld_sent state in lbs_send_confirmsleep().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When another scan is in progress, a direct scan gets dropped on the
floor. However, that direct scan is usually the scan that's really
needed by userspace, and gets stomped on by all the broadcast scans the
ipw2200 driver issues internally. Make sure the direct scan happens
eventually, and as a bonus ensure that the passive scan worker is
cleaned up when appropriate.
The change of request_passive_scan form a struct work to struct
delayed_work is only to make the set_wx_scan() code a bit simpler, it's
still only used with a delay of 0 to match previous behavior.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Now that walk_memory_resource() is available regardless of
MEMORY_HOTPLUG's setting, this dependency is not needed.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
l2tp: Fix possible oops if transmitting or receiving when tunnel goes down
tcp: Fix for race due to temporary drop of the socket lock in skb_splice_bits.
tcp: Increment OUTRSTS in tcp_send_active_reset()
raw: Raw socket leak.
lt2p: Fix possible WARN_ON from socket code when UDP socket is closed
USB ID for Philips CPWUA054/00 Wireless USB Adapter 11g
ssb: Fix context assertion in ssb_pcicore_dev_irqvecs_enable
libertas: fix command size for CMD_802_11_SUBSCRIBE_EVENT
ipw2200: expire and use oldest BSS on adhoc create
airo warning fix
b43legacy: Fix controller restart crash
sctp: Fix ECN markings for IPv6
sctp: Flush the queue only once during fast retransmit.
sctp: Start T3-RTX timer when fast retransmitting lowest TSN
sctp: Correctly implement Fast Recovery cwnd manipulations.
sctp: Move sctp_v4_dst_saddr out of loop
sctp: retran_path update bug fix
tcp: fix skb vs fack_count out-of-sync condition
sunhme: Cleanup use of deprecated calls to save_and_cli and restore_flags.
xfrm: xfrm_algo: correct usage of RIPEMD-160
...
|
|
Some problems have been experienced in the field which cause an oops
in the pppol2tp driver if L2TP tunnels fail while passing data.
The pppol2tp driver uses private data that is referenced via the
sk->sk_user_data of its UDP and PPPoL2TP sockets. This patch makes
sure that the driver uses sock_hold() when it holds a reference to the
sk pointer. This affects its sendmsg(), recvmsg(), getname(),
[gs]etsockopt() and ioctl() handlers.
Tested by ISP where problem was seen. System has been up 10 days with
no oops since running this patch. Without the patch, an oops would
occur every 1-2 days.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an L2TP daemon closes a tunnel socket while packets are queued in
the tunnel's reorder queue, a kernel warning is logged because the
socket is closed while skbs are still referencing it. The fix is to
purge the queue in the socket's release handler.
WARNING: at include/net/sock.h:351 udp_lib_unhash+0x41/0x68()
Pid: 12998, comm: openl2tpd Not tainted 2.6.25 #8
[<c0423c58>] warn_on_slowpath+0x41/0x51
[<c05d33a7>] udp_lib_unhash+0x41/0x68
[<c059424d>] sk_common_release+0x23/0x90
[<c05d16be>] udp_lib_close+0x8/0xa
[<c05d8684>] inet_release+0x42/0x48
[<c0592599>] sock_release+0x14/0x60
[<c059299f>] sock_close+0x29/0x30
[<c046ef52>] __fput+0xad/0x15b
[<c046f1d9>] fput+0x17/0x19
[<c046c8c4>] filp_close+0x50/0x5a
[<c046da06>] sys_close+0x69/0x9f
[<c04048ce>] syscall_call+0x7/0xb
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Enable the Philips CPWUA054/00 in p54usb.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The size was two small by two bytes.
Signed-off-by: Holger Schurig
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If there are no networks on the free list, expire the oldest one when
creating a new adhoc network. Because ipw2200 and the ieee80211 stack
don't actually cull old networks and place them back on the free list
unless they are needed for new probe responses, over time the free list
would become empty and creating an adhoc network would fail due to the !
list_empty(...) check.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
WARNING: space prohibited between function name and open parenthesis '('
#22: FILE: drivers/net/wireless/airo.c:2907:
+ while ((IN4500 (ai, COMMAND) & COMMAND_BUSY) && (delay < 10000)) {
total: 0 errors, 1 warnings, 8 lines checked
./patches/wireless-airo-waitbusy-wont-delay.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Dan Williams <dcbw@redhat.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Make use of local_irq_save and local_irq_restore rather then the
deprecated save_and_cli and restore_flags calls.
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following patch is seems to fix the tulip suspend/resume panic:
http://bugzilla.kernel.org/show_bug.cgi?id=8952#c46
My attempts at a cleaner patch failed and Pavel thinks this is OK.
Original from: kernelbugs@tap.homeip.net
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When using 4+ GB RAM and SWIOTLB is active, the driver corrupts
memory by writing an skb after the relevant DMA page has been
unmapped. Although this doesn't happen when *not* using bounce
buffers, clearing the pointer to the DMA page after unmapping
it fixes the problem.
http://marc.info/?t=120861317000005&r=2&w=2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Because we cache the last failed-to-xmit packet, if there are no
packets queued behind that one we may never send it (reproduced here
as TCP stalls, "cured" by an outgoing ping).
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
If we fail to transmit a packet, we assume the queue is full and put
the skb into last_xmit_skb. However, if more space frees up before we
xmit it, we loop, and the result can be transmitting the same skb twice.
Fix is simple: set skb to NULL if we've used it in some way, and check
before sending.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Update myri10ge version to 1.3.99-1.347.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 5a0a92e67b5009a71e011658da04fb92dad8961f mentions len < ETH_ZLEN
is true for ARP packets. This obviously is not unlikely.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
After request_dma() succeeding, any error path should do free_dma().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This is normal when the external link is down so don't report it as an error.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
llc: Fix double accounting of received packets
netfilter: nf_conntrack_expect: fix error path unwind in nf_conntrack_expect_init()
bluetooth: fix locking bug in the rfcomm socket cleanup handling
mac80211: fix alignment issue with compare_ether_addr()
mac80211: Fix for NULL pointer dereference in sta_info_get()
mac80211: fix a typo in ieee80211_handle_filtered_frame comment
rndis_wlan: add missing range check for power_output modparam
iwlwifi: fix rate scale TLC column selection bug
iwlwifi: fix exit from stay_in_table state
rndis_wlan: Make connections to TKIP PSK networks work
mac80211 : Fixes the status message for iwconfig
rt2x00: Use atomic interface iteration in irq context
rt2x00: Reset antenna RSSI after switch
rt2x00: Don't count retries as failure
rt2x00: Fix memleak in tx() path
mac80211: reorder channel and freq reporting in wext scan report
b43: Fix controller restart crash
mac80211: fix ieee80211_rx_bss_put/get imbalance
net/mac80211: always true conditionals
b43: Upload both beacon templates on initial load
...
|