summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2011-01-11ehea: Increase the skb array usageBreno Leitao
Currently the skb array is not fully allocated, and the allocation is done as it's requested, which is not the expected way. This patch just allocate the full skb array at driver initialization. Also, this patch increases ehea version to 107. Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-11net/fec: remove config FEC2 as it's used nowhereShawn Guo
Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-11pcnet_cs: add new_idKen Kawasaki
pcnet_cs: add another ID of "corega Ether CF-TD" 10Base-T PCMCIA card. Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10net/r8169: Update the function of parsing firmwarehayeswang
Update rtl_phy_write_fw function. The new function could parse the complex firmware which is used by RTL8111E and later. The new firmware may read data and do some operations, not just do writing only. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10net: ppp: use {get,put}_unaligned_be{16,32}Changli Gao
Signed-off-by: Changli Gao <xiaosuo@gmail.com> Reviewed-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10mlx4: Call alloc_etherdev to allocate RX and TX queuesTom Herbert
Changed driver to call alloc_etherdev_mqs so that the number of TX and RX queues can be set to correct values in the netdev device. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10cxgb4vf: fix mailbox data/control coherency domain raceCasey Leedom
For the VFs, the Mailbox Data "registers" are actually backed by T4's "MA" interface rather than PL Registers (as is the case for the PFs). Because these are in different coherency domains, the write to the VF's PL-register-backed Mailbox Control can race in front of the writes to the MA-backed VF Mailbox Data "registers". So we need to do a read-back on at least one byte of the VF Mailbox Data registers before doing the write to the VF Mailbox Control register. Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10qlcnic: change module parameter permissionsamit salecha
o Updating module parameter after driver load is not supported except auto_fw_reset parameter. Changing these parameter after driver load, can have weird result. o Update driver version to 5.0.15. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10qlcnic: fix ethtool diagnostics testSony Chacko
IRQ diag test was getting executed only when both register test and link test passed. The test should get executed if ETH_TEST_FL_OFFLINE flag is set. Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10qlcnic: fix flash fw version readamit salecha
Driver is reading flash fw version from defined address, this address may be invalid. Indeed Driver should read address for fw version through flash layout table. Flash layout table has defined region and address for fw version address should be read from fw image region. Driver has check for old firmware, this bug can cause driver load fail. This patch will try to read fw version from flash image region, if that fails, read from defined address. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10netdev: bfin_mac: let boards set vlan masksMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10netdev: bfin_mac: disable hardware checksum if writeback cache is enabledSonic Zhang
With writeback caches, corrupted RX packets will be sent up the stack without any error markings. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10netdev: bfin_mac: drop unused Mac dataMike Frysinger
We don't use this local "Mac" data anywhere (since we rely on the netdev's storage), so punt it. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10netdev: bfin_mac: mark setup_system_regs as staticMike Frysinger
No need for this to be exported since it is only used in this driver. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10netdev: bfin_mac: clean up printk messagesMike Frysinger
Use netdev_* and pr_* helper funcs for output rather than printk. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09ixgbe: update ntuple filter configurationAlexander Duyck
This change fixes several issues found in ntuple filtering while I was doing the ATR refactor. Specifically I updated the masks to work correctly with the latest version of ethtool, I cleaned up the exception handling and added detailed error output when a filter is rejected, and corrected several bits that were set incorrectly in ixgbe_type.h. The previous version of this patch included a printk that was left over from me fixing the filter setup. This patch does not include that printk. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09ixgbe: further flow director performance optimizationsAlexander Duyck
This change adds a compressed input type for atr signature hash computation. It also drops the use of the set functions when setting up the ATR input since we can then directly setup the hash input as two dwords that can be stored and passed as registers. With these changes the cost of computing the has is low enough that we can perform a hash computation on each TCP SYN flagged packet allowing us to drop the number of flow director misses considerably in tests such as netperf TCP_CRR. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09ixgbe: cleanup flow director hash computation to improve performanceAlexander Duyck
This change cleans up the layout of the flow director data, and the algorithm used to calculate the hash resulting in a 35x / 3500% performance increase versus the old flow director hash computation. The overall effect is only a 1% increase in transactions per second though due to the fact that only 1 packet in 20 are actually hashed upon. TCP_RR before: Socket Size Request Resp. Elapsed Trans. Send Recv Size Size Time Rate bytes Bytes bytes bytes secs. per sec 16384 87380 1 1 60.00 23059.27 16384 87380 TCP_RR after: Socket Size Request Resp. Elapsed Trans. Send Recv Size Size Time Rate bytes Bytes bytes bytes secs. per sec 16384 87380 1 1 60.00 23239.98 16384 87380 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09ixgbe: make sure per Rx queue is disabled before unmapping the receive bufferYi Zou
When disable the Rx logic globally, we would also want to disable the per Rx queue receive logic by per queue Rx control register RXDCTL so no more DMA is happening from the packet buffer to the receive buffer associated with the Rx ring, before we start unmapping Rx ring receive buffer. The hardware may take max of 100us before the corresponding Rx queue is really disabled. Added ixgbe_disable_rx_queue() for this purpose. Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09e1000: Add support for the CE4100 reference platformDirk Brandewie
This patch adds support for the gigabit phys present on the CE4100 reference platforms. Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09e1000e: add custom set_d[0|3]_lplu_state function pointer for 82574Bruce Allan
82574 needs to configure Low Power Link Up (or LPLU) differently than the other parts in the 8257x family supported by the driver. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09e1000e: power off PHY after reset when interface is downBruce Allan
Some Phys supported by the driver do not remain powered off across a reset of the device when the interface is down, e.g. on 82571, but not on 82574. This patch powers down (only when WoL is disabled) the PHY after a reset if the interface is down and the ethtool diagnostics are not currently running. The ethtool diagnostic function required a minor re-factor as a result, and the e1000_[get|put]_hw_control() functions are renamed since they are no longer static to netdev.c as they are needed by the ethtool diagnostics. A couple minor whitespace issues were cleaned up, too. Reported-by: Arthur Jones <ajones@riverbed.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09e1000e: use either_crc_le() rather than re-write itBruce Allan
For the 82579 jumbo frame workaround, there is no need to re-write the CRC calculation functionality already found in the kernel's ether_crc_le(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09e1000e: properly bounds-check string functionsBruce Allan
Use string functions with bounds checking rather than their non-bounds checking counterparts, and do not hard code these boundaries. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09e1000e: convert calls of ops.[read|write]_reg to e1e_[r|w]phyBruce Allan
Cleans up the code a bit by using the driver-specific e1e_rphy and e1e_wphy macros instead of the full function pointer variants. Fix a couple whitespace issue with two already existing calls to e1e_wphy. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09e1000e: cleanup variables set but not usedBruce Allan
The ICR register is clear on read and we don't care what the returned value is when resetting the hardware so the icr variable(s) can be removed. We should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and from e1000_get_phy_id_82571() (dump a debug message when it fails and when an unknown Phy id is returned). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09net offloading: Pass features into netif_needs_gso().Jesse Gross
Now that there is a single function that can compute the device features relevant to a packet, we don't want to run it for each offload. This converts netif_needs_gso() to take the features of the device, rather than computing them itself. Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09r8169: delay phy init until device opens.françois romieu
It workarounds the 60s firmware load failure timeout for the non-modular case. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09forcedeth: Do not use legacy PCI power managementRafael J. Wysocki
The forcedeth driver uses the legacy PCI power management, so it has to do PCI-specific things in its ->suspend() and ->resume() callbacks and some of them are not done correctly. Convert forcedeth to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions. Tested with nVidia Corporation MCP55 Ethernet (rev a2). Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09sky2: convert to new VLAN model (v0.2)Stephen Hemminger
This converts sky2 to new VLAN offload flags control via ethtool. It also allows for transmit offload of vlan tagged frames which was not possible before. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Reviewed-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09sky2: fix limited auto negotiationStephen Hemminger
The sky2 driver would always try all possible supported speeds even if the user only asked for a limited set of speed/duplex combinations. Reported-by: Mohsen Hariri <m.hariri@gmail.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09bnx2x: Fix the race on bp->stats_pending.Vladislav Zolotarov
Fix the race on bp->stats_pending between the timer and a LINK_UP event handler. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09bnx2x: Move to D0 before clearing MSI/MSI-X configuration.Vladislav Zolotarov
Move to D0 before clearing MSI/MSI-X configuration. Otherwise MSI/MSI-X won't be cleared. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09bnx2x: registers dump fixesVladislav Zolotarov
Fixes in registers dump: - Properly calculate dump length for 57712. - Prevent HW blocks parity attentions when dumping registers in order to prevent false parity errors handling. - Update the bnx2x_dump.h file: old one had a few bugs that could cause fatal HW error as a result of a registers dump. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09bnx2x: Don't prevent RSS configuration in INT#x and MSI interrupt modes.Vladislav Zolotarov
Don't prevent RSS configuration in INT#x and MSI interrupt modes. Otherwise Rx hash key won't be available. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09hamradio: Resolve memory leak due to missing firmware release in add_mcs()Jesper Juhl
Failure to release_firmware() in drivers/net/hamradio/yam.c::add_mcs() causes memory leak. This patch should fix it. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09net/fec: add dual fec support for mx28Shawn Guo
This patch is to add mx28 dual fec support. Here are some key notes for mx28 fec controller. - The mx28 fec controller naming ENET-MAC is a different IP from FEC used on other i.mx variants. But they are basically compatible on software interface, so it's possible to share the same driver. - ENET-MAC design on mx28 made an improper assumption that it runs on a big-endian system. As the result, driver has to swap every frame going to and coming from the controller. - The external phys can only be configured by fec0, which means fec1 can not work independently and both phys need to be configured by mii_bus attached on fec0. - ENET-MAC reset will get mac address registers reset too. - ENET-MAC MII/RMII mode and 10M/100M speed are configured differently FEC. - ETHER_EN bit must be set to get ENET-MAC interrupt work. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09net/fec: improve pm for better suspend/resumeShawn Guo
The following commit made a fix to use fec_enet_open/fec_enet_close over fec_enet_init/fec_stop for suspend/resume, because fec_enet_init does not allow to have a working network interface at resume. e3fe8558c7fc182972c3d947d88744482111f304 net/fec: fix pm to survive to suspend/resume This fix works for i.mx/mxc fec controller, but fails on mx28 fec which gets a different interrupt logic design. On i.mx fec, interrupt can be triggered even bit ETHER_EN of ECR register is not set. But on mx28 fec, ETHER_EN must be set to get interrupt work. Meanwhile, MII interrupt is mandatory to resume the driver, because MDIO read/write changed to interrupt mode by commit below. 97b72e4320a9aaa4a7f1592ee7d2da7e2c9bd349 fec: use interrupt for MDIO completion indication fec_restart/fec_stop comes out as the solution working for both cases. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09net/fec: add mac field into platform data and consolidate fec_get_macShawn Guo
Add mac field into fec_platform_data and consolidate function fec_get_mac to get mac address in following order. 1) module parameter via kernel command line fec.macaddr=0x00,0x04,... 2) from flash in case of CONFIG_M5272 or fec_platform_data mac field for others, which typically have mac stored in fuse 3) fec mac address registers set by bootloader Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09net/fec: remove the use of "index" which is legacyShawn Guo
The "index" becomes legacy since fep->pdev->id starts working to identify the instance. Moreover, the call of fec_enet_init(ndev, 0) always passes 0 to fep->index. This makes the following code in fec_get_mac buggy. /* Adjust MAC if using default MAC address */ if (iap == fec_mac_default) dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index; It may be the time to remove "index" and use fep->pdev->id instead. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09net/fec: fix MMFR_OP type in fec_enet_mdio_writeShawn Guo
FEC_MMFR_OP_WRITE should be used than FEC_MMFR_OP_READ in a mdio write operation. It's probably a typo introduced by commit: e6b043d512fa8d9a3801bf5d72bfa3b8fc3b3cc8 netdev/fec.c: add phylib supporting to enable carrier detection (v2) Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-07Merge branch 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wqLinus Torvalds
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits) usb: don't use flush_scheduled_work() speedtch: don't abuse struct delayed_work media/video: don't use flush_scheduled_work() media/video: explicitly flush request_module work ioc4: use static work_struct for ioc4_load_modules() init: don't call flush_scheduled_work() from do_initcalls() s390: don't use flush_scheduled_work() rtc: don't use flush_scheduled_work() mmc: update workqueue usages mfd: update workqueue usages dvb: don't use flush_scheduled_work() leds-wm8350: don't use flush_scheduled_work() mISDN: don't use flush_scheduled_work() macintosh/ams: don't use flush_scheduled_work() vmwgfx: don't use flush_scheduled_work() tpm: don't use flush_scheduled_work() sonypi: don't use flush_scheduled_work() hvsi: don't use flush_scheduled_work() xen: don't use flush_scheduled_work() gdrom: don't use flush_scheduled_work() ... Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c as per Tejun.
2011-01-07Merge branch 'usb-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6 * 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits) USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004) USB: serial: ftdi_sio: add support for TIOCSERGETLSR USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport USB: atmel_usba_udc: fix freeing irq in usba_udc_remove() usb: ehci-omap: fix tll channel enable mask usb: ohci-omap3: fix trivial typo USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096 USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's USB: gadget: update ci13xxx to work with g_ether USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers Revert "USB: musb: pm: don't rely fully on clock support" Revert "USB: musb: blackfin: pm: make it work" USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path USB: uas: Ensure we only bind to a UAS interface USB: uas: Rename sense pipe and sense urb to status pipe and status urb USB: uas: Use kzalloc instead of kmalloc USB: uas: Fix up the Sense IU usb: musb: core: kill unneeded #include's DA8xx: assign name to MUSB IRQ resource usb: gadget: g_ncm added ... Manually fix up trivial conflicts in USB Kconfig changes in: arch/arm/mach-omap2/Kconfig arch/sh/Kconfig drivers/usb/Kconfig drivers/usb/host/ehci-hcd.c and annoying chip clock data conflicts in: arch/arm/mach-omap2/clock3xxx_data.c arch/arm/mach-omap2/clock44xx_data.c
2011-01-06Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (416 commits) ARM: DMA: add support for DMA debugging ARM: PL011: add DMA burst threshold support for ST variants ARM: PL011: Add support for transmit DMA ARM: PL011: Ensure IRQs are disabled in UART interrupt handler ARM: PL011: Separate hardware FIFO size from TTY FIFO size ARM: PL011: Allow better handling of vendor data ARM: PL011: Ensure error flags are clear at startup ARM: PL011: include revision number in boot-time port printk ARM: vexpress: add sched_clock() for Versatile Express ARM i.MX53: Make MX53 EVK bootable ARM i.MX53: Some bug fix about MX53 MSL code ARM: 6607/1: sa1100: Update platform device registration ARM: 6606/1: sa1100: Fix platform device registration ARM i.MX51: rename IPU irqs ARM i.MX51: Add ipu clock support ARM: imx/mx27_3ds: Add PMIC support ARM: DMA: Replace page_to_dma()/dma_to_page() with pfn_to_dma()/dma_to_pfn() mx51: fix usb clock support MX51: Add support for usb host 2 arch/arm/plat-mxc/ehci.c: fix errors/typos ...
2011-01-06Merge branch 'devel-stable' into develRussell King
Conflicts: arch/arm/mach-pxa/clock.c arch/arm/mach-pxa/clock.h
2011-01-06cassini: Use local-mac-address prom property for Cassini MAC addressRichard Mortimer
Fallback on the local-mac-address prom property if the Cassini device does not have an address programmed in the VPD ROM. This uses the same technique as implemented by the sungem driver. The problem was reported by Frans van Berckel using Debian kernel 2.6.34-7 on Sun Fire V440. udev was assigning a new eth<n> device name on each reboot because the cassini driver was using a random MAC address. Fix tested on 2.6.34-7 and 2.6.37 Sun Fire V440. Compile tested against 2.6.36 davem/sparc-2.6.git Reported-by: Frans van Berckel <fberckel@xs4all.nl> Tested-by: Frans van Berckel <fberckel@xs4all.nl> Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-06netconsole: clarify stopping messageFerenc Wagner
Signed-off-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-06netconsole: don't announce stopping if nothing happenedFerenc Wagner
Signed-off-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-06cnic: Fix the type field in SPQ messagesMichael Chan
The new firmware interface requires each Slow Path Queue (SPQ) message's type field to include the function number. The existing code does not do this consistently. We fix this by OR'ing in the function number into the type field centrally in cnic_submit_kwqe_16(). Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-06net: r6040: Return proper error for r6040_init_oneAxel Lin
Return -ENOMEM instead of 0 for the case of mdiobus_alloc and kmalloc failure. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2024-10-10 23:32:18 +0000