| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit c3e70edd7c2eed6acd234627a6007627f5c76e8e ]
This reverts:
commit 33c133cc7598 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4f101c47791cdcb831b3ef1f831b1cc51e4fe03c ]
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2c0f8ce1b584a4d7b8ff53140d21dfed99834940 ]
Set and verify signature calculates the signature for each of the
mailbox nodes, even for those that are unused (from cache). Added
a missing length check to set and verify only those which are used.
While here, also moved the setting of msg's nodes token to where we
already go over them. This saves a pass because checksum is disabled,
and the only useful thing remaining that set signature does is setting
the token.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB
adapters')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 24b27fc4cdf9e10c5e79e5923b6b7c2c5c95096c ]
Following few steps will crash kernel -
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2cce76c3fab410520610a7d2f52faebc3cfcf843 upstream.
gcc-6 warns about code in il3945_hw_txq_ctx_free() being
somewhat ambiguous:
drivers/net/wireless/intel/iwlegacy/3945.c:1022:5: warning: suggest explicit braces to avoid ambiguous 'else' [-Wparentheses]
This adds a set of curly braces to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 362210e0dff4eb7bb36a9b34dbef3b39d779d95e upstream.
A cleanup patch in linux-3.18 moved around some code in the ath9k
driver and left some code to be indented in a misleading way,
made worse by the addition of some new code for p2p mode, as
discovered by a new gcc-6 warning:
drivers/net/wireless/ath/ath9k/init.c: In function 'ath9k_set_hw_capab':
drivers/net/wireless/ath/ath9k/init.c:851:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
hw->wiphy->iface_combinations = if_comb;
^~
drivers/net/wireless/ath/ath9k/init.c:847:3: note: ...this 'if' clause, but it is not
if (ath9k_is_chanctx_enabled())
^~
The code is in fact correct, but the indentation is not, so I'm
reformatting it as it should have been after the original cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 499afaccf6f3 ("ath9k: Isolate ath9k_use_chanctx module parameter")
Fixes: eb61f9f623f7 ("ath9k: advertise p2p dev support when chanctx")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f57e4d930d48217268315898212518d4d3e0773 upstream.
Rewrite abs() so that its return type does not depend on the
architecture and no unexpected type conversion happen inside of it. The
only conversion is from unsigned to signed type. char is left as a
return type but treated as a signed type regradless of it's actual
signedness.
With the old version, int arguments were promoted to long and depending
on architecture a long argument might result in s64 or long return type
(which may or may not be the same).
This came after some back and forth with Nicolas. The current macro has
different return type (for the same input type) depending on
architecture which might be midly iritating.
An alternative version would promote to int like so:
#define abs(x) __abs_choose_expr(x, long long, \
__abs_choose_expr(x, long, \
__builtin_choose_expr( \
sizeof(x) <= sizeof(int), \
({ int __x = (x); __x<0?-__x:__x; }), \
((void)0))))
I have no preference but imagine Linus might. :] Nicolas argument against
is that promoting to int causes iconsistent behaviour:
int main(void) {
unsigned short a = 0, b = 1, c = a - b;
unsigned short d = abs(a - b);
unsigned short e = abs(c);
printf("%u %u\n", d, e); // prints: 1 65535
}
Then again, no sane person expects consistent behaviour from C integer
arithmetic. ;)
Note:
__builtin_types_compatible_p(unsigned char, char) is always false, and
__builtin_types_compatible_p(signed char, char) is also always false.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7711aaf08ad3fc4d0e937eec1de0a63620444ce7 upstream.
A station pointer can be passed to the driver on tx, before it has been
marked as associated. Since ath9k_sta_state was initializing the entry
too late, it resulted in some spurious crashes.
Fixes: df3c6eb34da5 ("ath9k: Use sta_state() callback")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1423661fed2c40d6d71b5e2e3aa390f85157f9d5 upstream.
The ethtool_ops .get_regs function attempts to read the nonexistent
register NIC_QSET_SQ_0_7_CNM_CHG, which produces a "bus error" type
OOPs.
Fix by not attempting to read, and removing the definition of,
NIC_QSET_SQ_0_7_CNM_CHG. A zero is written into the register dump to
keep the layout unchanged.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3f4c68cfde30caa1f6d8368fd19590671411ade2 ]
Check for SMU RX local/remote faults along with SPU LINK
status. Otherwise at times link is UP at our end but DOWN
at link partner's side. Also due to an issue in BGX it's
rarely seen that initialization doesn't happen properly
and SMU RX reports faults with everything fine at SPU.
This patch tries to reinitialize LMAC to fix it.
Also fixed LMAC disable sequence to properly bring down link.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Tao Wang <tao.wang@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ad2ecebd67d8a80fe5412d11df375a5ed2db7cd1 ]
Counting rx packets for every CQE_RX in CQ irq handler is incorrect.
Synchronization is missing when multiple queues are receiving packets
simultaneously. Like transmit packet stats use HW stats here.
Also removed unused 'cqe_type' parameter in nicvf_rcv_pkt_handler().
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6a9bab79bb79bd9b2eda16f0aba1b4c43f677be9 ]
When a interface is assigned morethan 8 queues and the logical interface
is toggled i.e down & up, additional queues or qsets are not initialized
as secondary qset count is being set to zero while tearing down.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2fcb92fbd04eef26dfe7e67839da6262d83d6b65 ]
Calling mlx5e_set_coalesce while the interface is down will result in
modifying CQs that don't exist.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7524a5d88b94afef8397a79f1e664af5b7052c22 ]
If CQ moderation is not supported by the device, print a warning on
netdevice load, and return error when trying to modify/query cq
moderation via ethtool.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4c0b6eaf373a5323f03a3a20c42fc435715b073d ]
On Thunderx pass 1.x and pass2 due to a HW errata default CQ
DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset
error when packets are being received at >20Mpps resulting in
complete stall of packet reception.
This patch will configure it to 0x100 which is what is expected
by HW on Thunderx. On future passes of thunderx and other chips
HW default/reset value will be 0x100 or higher hence not overwritten.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6e35c04cf633e55648acb9ccabff42aa37bd4044 ]
This patch fixes the Hash PCTYPE enable for X722 since it supports
a broader selection of PCTYPES for TCP and UDP.
This patch also fixes a bug in XL710, X710, X722 support for RSS,
as of now we cannot reduce the (4)tuple for RSS for TCP/IPv4/IPV6 or
UDP/IPv4/IPv6 packets since this requires a product feature change
that comes in a later release.
A VF should never be allowed to change the tuples for RSS for any
PCTYPE since that's a global setting for the device in case of i40e
devices.
Change-ID: I0ee7203c9b24813260f58f3220798bc9d9ac4a12
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 19a6d156a7bd080f3a855a40a4a08ab475e34b4a ]
smatch detected a suspicious looking bitop condition:
drivers/net/ethernet/cavium/liquidio/lio_main.c:2529
handle_timestamp() warn: suspicious bitop condition
(skb_shinfo(skb)->tx_flags | SKBTX_IN_PROGRESS is always non-zero,
so the logic is definitely not correct. Use & to mask the correct
bit.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e00e23bceba48a8f0c94fefe26948404cbd43d0a ]
This patch addresses two issues.
First is the fact that the fm10k_mbx_free_irq was assuming msix_entries was
valid and that will not always be the case. As such we need to add a check
for if it is NULL.
Second is the fact that we weren't freeing the IRQ if the mailbox API
returned an error on trying to connect.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 587731e684dcf3522215194a02357d26b9bc7277 ]
If the q_vector allocation fails we should free the resources associated
with the MSI-X vector table.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 875328e4bce696e85edcda3c4b0ec80fd525e3a3 ]
The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1343c65f70ee1b1f968a08b30e1836a4e37116cd ]
A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.
Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.
In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.
Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e8d5b5975401c83641efd5d4595e6cdbe9e9e2f ]
VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks. To resolve this, we added a
check first to ensure that the first queue is infact owned by the VF at
init_hw_vf time. However, the code flow did not reset hw->mac.max_queues
to 0. In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9f872986479b6e0543eb5c615e5f9491bb04e5c1 ]
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c7ee6d2cacc7794a91875ef5fd8284b4a900d8c ]
Based on hardware testing, the host interface supports up to 15368 bytes
as the maximum frame size. To determine the correct MTU, we subtract 8
for the internal switch tag, 14 for the L2 header, and 4 for the
appended FCS header, resulting in 15342 bytes of payload for our maximum
MTU on jumbo frames.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1340181fe435ccb8ca2f996b8680bd9566860619 ]
It is possible that the PF has not yet assigned resources to the VF.
Although rare, this could result in the VF attempting to read queues it
does not own and result in FUM or THI faults in the PF. To prevent this,
check queue 0 before we continue in init_hw_vf.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b77ac46bbae862dcb3f51296825c940404c69b0f ]
This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.
The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Leonid Bloch <leonid@daynix.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9eab46b7cb8d0b0dcf014bf7b25e0e72b9e4d929 ]
e1000_clean_tx_irq cleans buffers and sets tx_ring->next_to_clean,
then e1000_xmit_frame reuses the cleaned buffers. But there are no
memory barriers when buffers gets recycled, so the recycled buffers
can be corrupted.
Use smp_store_release to update tx_ring->next_to_clean and
smp_load_acquire to read tx_ring->next_to_clean to properly
hand off buffers from e1000_clean_tx_irq to e1000_xmit_frame.
The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5d6002b7b822c7423e75d4651e6790bfb5642b1b ]
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit be06998f96ecb93938ad2cce46c4289bf7cf45bc ]
The combined effect of commits 6423fc3416 ("igb: do not re-init SR-IOV
during probe") and ceee3450b3 ("igb: make sure SR-IOV init uses the
right number of queues") causes VFs no longer getting set up, leading
to NULL pointer dereferences due to the adapter's ->vf_data being NULL
while ->vfs_allocated_count is non-zero. The first commit not only
neglected the side effect of igb_sriov_reinit() that the second commit
tried to account for, but also that of setting IGB_FLAG_HAS_MSIX,
without which igb_enable_sriov() is effectively a no-op. Calling
igb_{,re}set_interrupt_capability() as done here seems to address this,
but I'm not sure whether this is better than sinply reverting the other
two commits.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 08c991297582114a6e1220f913eec91789c4eac6 ]
The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Reported-by: Roman Hodek <roman.aud@siemens.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 73bf8048d7c86a20a59d427e55deb1a778e94df7 ]
I've got a startech thunderbolt dock someone loaned me, which among other
things, has the following device in it:
08:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)
This hotplugs just fine (kernel 4.2.0 plus a patch or two here):
[ 863.020315] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.18-k
[ 863.020316] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 863.028657] igb 0000:08:00.0: enabling device (0000 -> 0002)
[ 863.062089] igb 0000:08:00.0: added PHC on eth0
[ 863.062090] igb 0000:08:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 863.062091] igb 0000:08:00.0: eth0: (PCIe:2.5Gb/s:Width x1) e8:ea:6a:00:1b:2a
[ 863.062194] igb 0000:08:00.0: eth0: PBA No: 000200-000
[ 863.062196] igb 0000:08:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
[ 863.064889] igb 0000:08:00.0 enp8s0: renamed from eth0
But disconnecting it is another story:
[ 1002.807932] igb 0000:08:00.0: removed PHC on enp8s0
[ 1002.807944] igb 0000:08:00.0 enp8s0: PCIe link lost, device now detached
[ 1003.341141] ------------[ cut here ]------------
[ 1003.341148] WARNING: CPU: 0 PID: 199 at lib/iomap.c:43 bad_io_access+0x38/0x40()
[ 1003.341149] Bad IO access at port 0x0 ()
[ 1003.342767] Modules linked in: snd_usb_audio snd_usbmidi_lib snd_rawmidi igb dca firewire_ohci firewire_core crc_itu_t rfcomm ctr ccm arc4 iwlmvm mac80211 fuse xt_CHECKSUM ipt_MASQUERADE
nf_nat_masquerade_ipv4 tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat
nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat
nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter bnep dm_mirror dm_region_hash dm_log dm_mod coretemp x86_pkg_temp_thermal intel_powerclamp kvm_intel snd_hda_codec_hdmi kvm
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel drbg
[ 1003.342793] ansi_cprng aesni_intel hp_wmi aes_x86_64 iTCO_wdt lrw iTCO_vendor_support ppdev gf128mul sparse_keymap glue_helper ablk_helper cryptd snd_hda_codec_realtek snd_hda_codec_generic
microcode snd_hda_intel uvcvideo iwlwifi snd_hda_codec videobuf2_vmalloc videobuf2_memops snd_hda_core videobuf2_core snd_hwdep btusb v4l2_common btrtl snd_seq btbcm btintel videodev cfg80211
snd_seq_device rtsx_pci_ms bluetooth pcspkr input_leds i2c_i801 media parport_pc memstick rfkill sg lpc_ich snd_pcm 8250_fintek parport joydev snd_timer snd soundcore hp_accel ie31200_edac
mei_me lis3lv02d edac_core input_polldev mei hp_wireless shpchp tpm_infineon sch_fq_codel nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables autofs4 xfs libcrc32c sd_mod sr_mod cdrom
rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci
[ 1003.342822] nouveau ahci libahci mxm_wmi e1000e xhci_pci hwmon ptp drm_kms_helper pps_core xhci_hcd ttm wmi video ipv6
[ 1003.342839] CPU: 0 PID: 199 Comm: kworker/0:2 Not tainted 4.2.0-2.el7_UNSUPPORTED.x86_64 #1
[ 1003.342840] Hardware name: Hewlett-Packard HP ZBook 15 G2/2253, BIOS M70 Ver. 01.07 02/26/2015
[ 1003.342843] Workqueue: pciehp-3 pciehp_power_thread
[ 1003.342844] ffffffff81a90655 ffff8804866d3b48 ffffffff8164763a 0000000000000000
[ 1003.342846] ffff8804866d3b98 ffff8804866d3b88 ffffffff8107134a ffff8804866d3b88
[ 1003.342847] ffff880486f46000 ffff88046c8a8000 ffff880486f46840 ffff88046c8a8098
[ 1003.342848] Call Trace:
[ 1003.342852] [<ffffffff8164763a>] dump_stack+0x45/0x57
[ 1003.342855] [<ffffffff8107134a>] warn_slowpath_common+0x8a/0xc0
[ 1003.342857] [<ffffffff810713c6>] warn_slowpath_fmt+0x46/0x50
[ 1003.342859] [<ffffffff8133719e>] ? pci_disable_msix+0x3e/0x50
[ 1003.342860] [<ffffffff812f6328>] bad_io_access+0x38/0x40
[ 1003.342861] [<ffffffff812f6567>] pci_iounmap+0x27/0x40
[ 1003.342865] [<ffffffffa0b728d7>] igb_remove+0xc7/0x160 [igb]
[ 1003.342867] [<ffffffff8132189f>] pci_device_remove+0x3f/0xc0
[ 1003.342869] [<ffffffff81433426>] __device_release_driver+0x96/0x130
[ 1003.342870] [<ffffffff814334e3>] device_release_driver+0x23/0x30
[ 1003.342871] [<ffffffff8131b404>] pci_stop_bus_device+0x94/0xa0
[ 1003.342872] [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0
[ 1003.342873] [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0
[ 1003.342874] [<ffffffff8131b516>] pci_stop_and_remove_bus_device+0x16/0x30
[ 1003.342876] [<ffffffff81333f5b>] pciehp_unconfigure_device+0x9b/0x180
[ 1003.342877] [<ffffffff81333a73>] pciehp_disable_slot+0x43/0xb0
[ 1003.342878] [<ffffffff81333b6d>] pciehp_power_thread+0x8d/0xb0
[ 1003.342885] [<ffffffff810881b2>] process_one_work+0x152/0x3d0
[ 1003.342886] [<ffffffff8108854a>] worker_thread+0x11a/0x460
[ 1003.342887] [<ffffffff81088430>] ? process_one_work+0x3d0/0x3d0
[ 1003.342890] [<ffffffff8108ddd9>] kthread+0xc9/0xe0
[ 1003.342891] [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180
[ 1003.342893] [<ffffffff8164e29f>] ret_from_fork+0x3f/0x70
[ 1003.342894] [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180
[ 1003.342895] ---[ end trace 65a77e06d5aa9358 ]---
Upon looking at the igb driver, I see that igb_rd32() attempted to read from
hw_addr and failed, so it set hw->hw_addr to NULL and spit out the message
in the log output above, "PCIe link lost, device now detached".
Well, now that hw_addr is NULL, the attempt to call pci_iounmap is obviously
not going to go well. As suggested by Mark Rustad, do something similar to
what ixgbe does, and save a copy of hw_addr as adapter->io_addr, so we can
still call pci_iounmap on it on teardown. Additionally, for consistency,
make the pci_iomap call assignment directly to io_addr, so map and unmap
match.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 857942fd1aa15edf7356a4a4bad5369c8e70a633 ]
If the driver calls skb_set_hash even with a zero hash, that
indicates to the stack that the hash calculation is offloaded
in hardware. So the Stack doesn't do a SW hash which is required
for load balancing if the user decides to turn of rx-hashing
on our device.
This patch fixes the path so that we do not call skb_set_hash
if the feature is disabled.
Change-ID: Ic4debfa4ff91b5a72e447348a75768ed7a2d3e1b
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f11999987bc0b5559ab56dedc6f4ca32fab5438a ]
Clean the whole mac filter list when resetting after an intermediate
add or delete push to the firmware. The code had evolved from using
a list from the stack to a heap allocation, but the memset() didn't
follow the change correctly. This now cleans the whole list rather
that just part of the first element.
Change-ID: I4cd03d5a103b7407dd8556a3a231e800f2d6f2d5
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fdb47ae87af537b24977a03bc69cfe1c5c55ca62 ]
If the driver gets unloaded during reset recovery, it's possible
that it will attempt to free resources when they're already free.
Add a check to make sure that the Tx and Rx rings actually exist
before dereferencing them to free resources.
Change-ID: I4d2b7e9ede49f634d421a4c5deaa5446bc755eee
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b7b713a8eaf325607d37229f024ad0b9f3e7f320 ]
When VFs are created, the MAC address defaults to all zeros, indicating
to the VF driver that it should use a random MAC address. However, the
PF driver was incorrectly adding this zero MAC to the filter table,
along with the VF's randomly generated MAC address.
Check for a good address before adding the default filter. While we're
at it, make the error message a bit more useful.
Change-ID: Ia100947d68140e0f73a19ba755cbffc3e79a8fcf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b36e9ab59b7e3a5b14bf88dc0536e6579db7b54d ]
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a42e7a369ea2b73a554a85dea7d6243af51cd4f0 ]
This patch fixes the memory leak which would be seen otherwise when user
programs flow-director filter using ethtool (sideband filter programming).
When ethtool is used to program flow directory filter, 'raw_buf' gets
allocated and it is supposed to be freed as part of queue cleanup. But
check of 'tx_buffer->skb' was preventing it from being freed.
Change-ID: Ief4f0a1a32a653180498bf6e987c1b4342ab8923
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e4425ed641f3eef67c892bc541949cd745a9ba9 ]
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6a7fded776a778f728b13d83a2c9fc893580c080 ]
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump amd when
it does a WB. It also optimizes when we do a wmb.
Change-ID: Id831e1ae7d3e2ec3f52cd0917b41ce1d22d75d9d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1418c3458118c6969d08e23aa377da7e2a7be36c ]
When a lot (many hundreds) of MAC or VLAN filters are added at one time,
we can overflow the Admin Queue buffer size with all the requests.
Unfortunately, the driver would then calculate the message size
incorrectly, causing it to be rejected by the PF. Furthermore, there was
no mechanism to trigger another request to allow for configuring the
rest of the filters that didn't fit into the first request.
To fix this, recalculate the correct buffer size when we detect the
overflow condition instead of just assuming the max buffer size. Also,
don't clear the request bit in adapter->aq_required when we have an
overflow, so that the rest of the filters can be processed later.
Change-ID: Idd7cbbc5af31315e0dcb1b10e6a02ad9817ce65c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4f2f017c6101ab2ba202d6059c238c15577ad38b ]
HW/NVM sets a limit of no less than 256 bytes for MSS. Stack can send as
low as 76 bytes MSS. This patch lowers the HW limit to 64 bytes to avoid
MDDs from firing and causing a reset when the MSS is lower than 256.
Change-ID: I36b500a6bb227d283c3e321a7718e0672b11fab0
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d06dd537f95683aba3651098ae288b7cbff8274 upstream.
usbnet_link_change will call schedule_work and should be
avoided if bind is failing. Otherwise we will end up with
scheduled work referring to a netdev which has gone away.
Instead of making the call conditional, we can just defer
it to usbnet_probe, using the driver_info flag made for
this purpose.
Fixes: 8a34b0ae8778 ("usbnet: cdc_ncm: apply usbnet_link_change")
Reported-by: Andrey Konovalov <andreyknvl@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 59d3f1ceb69b54569685d0c34dff16a1e0816b19 ]
Slowpath completion handling is incorrectly changing
SPQ_RING_SIZE bits instead of a single one.
Fixes: 76a9a3642a0b ("qed: fix handling of concurrent ramrods")
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e86663c475d384ab5f46cb5637e9b7ad08c5c505 ]
Nothing is decrementing the index "i" while we are cleaning up the
fragments we could not successful transmit.
Fixes: 9cde94506eacf ("bgmac: implement scatter/gather support")
Reported-by: coverity (CID 1352048)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 005db31d5f5f7c31cfdc43505d77eb3ca5cf8ec6 ]
Commit e826eafa65c6 ("bonding: Call netif_carrier_off after
register_netdevice") moved netif_carrier_off() from bond_init() to
bond_create(), but the latter is called only for initial default
devices and ones created through sysfs:
$ modprobe bonding
$ echo +bond1 > /sys/class/net/bonding_masters
$ ip link add bond2 type bond
$ grep "MII Status" /proc/net/bonding/*
/proc/net/bonding/bond0:MII Status: down
/proc/net/bonding/bond1:MII Status: down
/proc/net/bonding/bond2:MII Status: up
Ensure that carrier is initially off also for devices created through
netlink.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06708f81528725148473c0869d6af5f809c6824b upstream.
Commit aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25e1ed6e64f52a692ba3191c4fde650aab3ecc07 upstream.
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...
This patch adds a private dellink function for the CAN device driver interface
that does just nothing.
It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bce271f255dae8335dc4d2ee2c4531e09cc67f5a upstream.
With upstream commit bb208f144cf3f59 (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.
When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
access
commit 427460c83cdf55069eee49799a0caef7dde8df69 upstream.
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 43200a4480cbbe660309621817f54cbb93907108 upstream.
At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
