| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This is the 5.4.193 stable release
Conflicts:
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
drivers/edac/synopsys_edac.c
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/mmc/host/sdhci.c
drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
sound/soc/codecs/msm8916-wcd-analog.c
|
|
commit 805dfc18dd3d4dd97a987d4406593b5a225b1253 upstream.
In advk_pcie_handle_msi() it is expected that when bit i in the W1C
register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is
updated to contain the MSI number corresponding to index i.
Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG
always contains the number of the last received MSI, overall.
Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt
number. Since Aardvark already forbids more than 32 interrupts and uses
own allocated hwirq numbers, the msi_idx already corresponds to the
received MSI number.
Link: https://lore.kernel.org/r/20220110015018.26359-3-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d8dc1f7cd007a7ce94c5b4c20d63a8b8d6d7751 upstream.
We already clear all the other interrupts (ISR0, ISR1, HOST_CTRL_INT).
Define a new macro PCIE_MSI_ALL_MASK and do the same clearing for MSIs,
to ensure that we don't start receiving spurious interrupts.
Use this new mask in advk_pcie_handle_msi();
Link: https://lore.kernel.org/r/20211130172913.9727-5-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9f72d4757cbe4d1ed669192f6d23817c9e437c4b ]
The Qualcomm PCI bridge device (Device ID 0x0110) found in chipsets such as
SM8450 does not set the Command Completed bit unless writes to the Slot
Command register change "Control" bits.
This results in timeouts like below:
pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
Add the device to the Command Completed quirk to mark commands "completed"
immediately unless they change the "Control" bits.
Link: https://lore.kernel.org/r/20220210145003.135907-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0b0b8b897f8e12b2368e868bd7cdc5742d5c5a9 ]
Aardvark hardware supports Multi-MSI and MSI_FLAG_MULTI_PCI_MSI is already
set for the MSI chip. But when allocating MSI interrupt numbers for
Multi-MSI, the numbers need to be properly aligned, otherwise endpoint
devices send MSI interrupt with incorrect numbers.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area().
To ensure that aligned MSI interrupt numbers are used by endpoint devices,
we cannot use Linux virtual irq numbers (as they are random and not
properly aligned). Instead we need to use the aligned hwirq numbers.
This change fixes receiving MSI interrupts on Armada 3720 boards and
allows using NVMe disks which use Multi-MSI feature with 3 interrupts.
Without this NVMe disks freeze booting as linux nvme-core.c is waiting
60s for an interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-4-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 92c45b63ce22c8898aa41806e8d6692bcd577510 ]
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb2659230120, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Fixes: fb2659230120 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes")
Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 735f5ae49e1b44742cc63ca9b5c1ffde3e94ba91 ]
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
Link: https://lore.kernel.org/r/20220110015018.26359-15-kabel@kernel.org
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 92912b175178c7e895f5e5e9f1e30ac30319162b upstream.
Writes to a Downstream Port's Slot Control register are PCIe hotplug
"commands." If the Port supports Command Completed events, software must
wait for a command to complete before writing to Slot Control again.
pcie_do_write_cmd() sets ctrl->cmd_busy when it writes to Slot Control. If
software notification is enabled, i.e., PCI_EXP_SLTCTL_HPIE and
PCI_EXP_SLTCTL_CCIE are set, ctrl->cmd_busy is cleared by pciehp_isr().
But when software notification is disabled, as it is when pcie_init()
powers off an empty slot, pcie_wait_cmd() uses pcie_poll_cmd() to poll for
command completion, and it neglects to clear ctrl->cmd_busy, which leads to
spurious timeouts:
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x01c0 (issued 2264 msec ago)
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x05c0 (issued 2288 msec ago)
Clear ctrl->cmd_busy in pcie_poll_cmd() when it detects a Command Completed
event (PCI_EXP_SLTSTA_CC).
[bhelgaas: commit log]
Fixes: a5dd4b4b0570 ("PCI: pciehp: Wait for hotplug command completion where necessary")
Link: https://lore.kernel.org/r/20211111054258.7309-1-zhangliguang@linux.alibaba.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215143
Link: https://lore.kernel.org/r/20211126173309.GA12255@wunner.de
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the PCI-E standard the PERST# signal (reset-gpio in
fsl,imx6* compatible dts) should be kept asserted for at least 100 usec
before the PCI-E refclock is stable, should be kept asserted for at
least 100ms after the power rails are stable and the host should wait
at least 100 msec after it is de-asserted before accessing the
configuration space of any attached device.
From PCI Express Card Electromechanical Specification
T-PVPERL: Power stable to PERST# inactive - 100 msec
T-PERST-CLK: REFCLK stable before PERST# inactive 100 usec.
From PCI Express Base Specification:
To allow components to perform internal initialization, system
software must wait for at least 100 ms from the end of a Conventional
Reset of one or more devices before it is permitted to issue
Configuration Requests to those devices
Failure to do so could prevent PCI-E devices to be working correctly,
and this was experienced with real devices.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
|
|
commit 23584c1ed3e15a6f4bfab8dc5a88d94ab929ee12 upstream.
The Power Fault Detected bit in the Slot Status register differs from
all other hotplug events in that it is sticky: It can only be cleared
after turning off slot power. Per PCIe r5.0, sec. 6.7.1.8:
If a power controller detects a main power fault on the hot-plug slot,
it must automatically set its internal main power fault latch [...].
The main power fault latch is cleared when software turns off power to
the hot-plug slot.
The stickiness used to cause interrupt storms and infinite loops which
were fixed in 2009 by commits 5651c48cfafe ("PCI pciehp: fix power fault
interrupt storm problem") and 99f0169c17f3 ("PCI: pciehp: enable
software notification on empty slots").
Unfortunately in 2020 the infinite loop issue was inadvertently
reintroduced by commit 8edf5332c393 ("PCI: pciehp: Fix MSI interrupt
race"): The hardirq handler pciehp_isr() clears the PFD bit until
pciehp's power_fault_detected flag is set. That happens in the IRQ
thread pciehp_ist(), which never learns of the event because the hardirq
handler is stuck in an infinite loop. Fix by setting the
power_fault_detected flag already in the hardirq handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214989
Link: https://lore.kernel.org/linux-pci/DM8PR11MB5702255A6A92F735D90A4446868B9@DM8PR11MB5702.namprd11.prod.outlook.com
Fixes: 8edf5332c393 ("PCI: pciehp: Fix MSI interrupt race")
Link: https://lore.kernel.org/r/66eaeef31d4997ceea357ad93259f290ededecfd.1637187226.git.lukas@wunner.de
Reported-by: Joseph Bao <joseph.bao@intel.com>
Tested-by: Joseph Bao <joseph.bao@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3be9d243b21724d49b65043d4520d688b6040b36 upstream.
Since all PCI Express device Functions are required to implement the PCI
Express Capability structure, Capabilities List bit in PCI Status Register
must be hardwired to 1b. Capabilities Pointer register (which is already
set by pci-bride-emul.c driver) is valid only when Capabilities List is set
to 1b.
Link: https://lore.kernel.org/r/20211124155944.1290-7-pali@kernel.org
Fixes: 23a5fba4d941 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f1050c5e1fefb34ac90a506b43e9da803b5f8f7 upstream.
Older mvebu hardware provides PCIe Capability structure only in version 1.
New mvebu and aardvark hardware provides it in version 2. So do not force
version to 2 in pci_bridge_emul_init() and rather allow drivers to set
correct version. Drivers need to set version in pcie_conf.cap field without
overwriting PCI_CAP_LIST_ID register. Both drivers (mvebu and aardvark) do
not provide slot support yet, so do not set PCI_EXP_FLAGS_SLOT flag.
Link: https://lore.kernel.org/r/20211124155944.1290-6-pali@kernel.org
Fixes: 23a5fba4d941 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b067ac63a5730d2fae18399fed7e45f23d36912 upstream.
Some bits in PCI config space are reserved when device is PCIe. Properly
define behavior of PCI registers for PCIe emulated bridge and ensure that
it would not be possible change these reserved bits.
Link: https://lore.kernel.org/r/20211124155944.1290-3-pali@kernel.org
Fixes: 23a5fba4d941 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 29bbc35e29d9b6347780dcacde2deb4b39344167 ]
pci_irq_vector() and pci_irq_get_affinity() use the list position to find the
MSI-X descriptor at a given index. That's correct for the normal case where
the entry number is the same as the list position.
But it's wrong for cases where MSI-X was allocated with an entries array
describing sparse entry numbers into the hardware message descriptor
table. That's inconsistent at best.
Make it always check the entry number because that's what the zero base
index really means. This change won't break existing users which use a
sparse entries array for allocation because these users retrieve the Linux
interrupt number from the entries array after allocation and none of them
uses pci_irq_vector() or pci_irq_get_affinity().
Fixes: aff171641d18 ("PCI: Provide sensible IRQ vector alloc/free routines")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210223.929792157@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e445375882883f69018aa669b67cbb37ec873406 upstream.
Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU. Add it to the list of devices that need the
quirk.
Without this patch, device initialization fails with DMA errors:
ata8: softreset failed (1st FIS failed)
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
After applying the patch, the controller can be successfully initialized:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
ata8.00: ATAPI: PIONEER BD-RW BDR-207M, 1.21, max UDMA/100
ata8.00: configured for UDMA/100
scsi 7:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.21 PQ: 0 ANSI: 5
Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work
Reported-by: Sam Bingner <sam@bingner.com>
Tested-by: Sam Bingner <sam@bingner.com>
Tested-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
toradex_5.4-2.3.x-imx-v5.4.161
Conflicts:
drivers/net/phy/micrel.c
drivers/usb/chipidea/core.c
|
|
This is the 5.4.161 stable release
|
|
This is the 5.4.160 stable release
|
|
commit 83dbf898a2d45289be875deb580e93050ba67529 upstream.
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1f1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94185adbfad56815c2c8401e16d81bdb74a79201 upstream.
PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.
That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:
Capabilities: [b0] MSI-X: Enable- Count=67 Masked+
Clear the bit in the error path to restore the reset state.
Fixes: 438553958ba1 ("PCI/MSI: Enable and mask MSI-X early")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tufevoqx.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc4fac42e5f8460af09c0a7f2f1915be09e20c71 upstream.
Aardvark supports PCIe Hot Reset via PCIE_CORE_CTRL1_REG.
Use it for implementing PCI_BRIDGE_CTL_BUS_RESET bit of PCI_BRIDGE_CONTROL
register on emulated bridge.
With this, the function pci_reset_secondary_bus() starts working and can
reset connected PCIe card. Custom userspace script [1] which uses setpci
can trigger PCIe Hot Reset and reset the card manually.
[1] https://alexforencich.com/wiki/en/pcie/hot-reset-linux
Link: https://lore.kernel.org/r/20211028185659.20329-7-kabel@kernel.org
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84e1b4045dc887b78bdc87d92927093dc3a465aa upstream.
Aardvark controller has something like config space of a Root Port
available at offset 0x0 of internal registers - these registers are used
for implementation of the emulated bridge.
The default value of Class Code of this bridge corresponds to a RAID Mass
storage controller, though. (This is probably intended for when the
controller is used as Endpoint.)
Change the Class Code to correspond to a PCI Bridge.
Add comment explaining this change.
Link: https://lore.kernel.org/r/20211028185659.20329-6-kabel@kernel.org
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 771153fc884f566a89af2d30033b7f3bc6e24e84 upstream.
>From very vague, ambiguous and incomplete information from Marvell we
deduced that the 32-bit Aardvark register at address 0x4
(PCIE_CORE_CMD_STATUS_REG), which is not documented for Root Complex mode
in the Functional Specification (only for Endpoint mode), controls two
16-bit PCIe registers: Command Register and Status Registers of PCIe Root
Port.
This means that bit 2 controls bus mastering and forwarding of memory and
I/O requests in the upstream direction. According to PCI specifications
bits [0:2] of Command Register, this should be by default disabled on
reset. So explicitly disable these bits at early setup of the Aardvark
driver.
Remove code which unconditionally enables all 3 bits and let kernel code
(via pci_set_master() function) to handle bus mastering of Root PCIe
Bridge via emulated PCI_COMMAND on emulated bridge.
Link: https://lore.kernel.org/r/20211028185659.20329-5-kabel@kernel.org
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # b2a56469d550 ("PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f76b36d40beee0a13aa8f6aa011df0d7cbbb8a7f upstream.
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbffac ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced18 ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582f5 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851daa ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 454c53271fc11f3aa5e44e41fd99ca181bd32c62 upstream.
PCIe config space can be initialized also before pci_bridge_emul_init()
call, so move rootcap initialization after PCI config space initialization.
This simplifies the function a little since it removes one if (ret < 0)
check.
Link: https://lore.kernel.org/r/20211005180952.6812-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 223dec14a05337a4155f1deed46d2becce4d00fd upstream.
Commit 43f5c77bcbd2 ("PCI: aardvark: Fix reporting CRS value") fixed
handling of CRS response and when CRSSVE flag was not enabled it marked CRS
response as failed transaction (due to simplicity).
But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count
for PIO config response and so we can with a small change implement
re-issuing of config requests as described in PCIe base specification.
This change implements re-issuing of config requests when response is CRS.
Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the
transaction is marked as failed and an all-ones value is returned as
before.
We do this by returning appropriate error codes from function
advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then
reissues transaction.
Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4e17d65dafdd3513042d8f00404c9b6068a825c upstream.
Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.
Without this kernel prints suspicious line:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)
With this change it changes to:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)
Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 64f160e19e9264a7f6d89c516baae1473b6f8359 upstream.
In commit 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a55, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window configuration")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8ee579d53aca887d93f5f411462f25c085a5106 upstream.
We allow up to PCI_EXP_SLTSTA2 registers to be accessed, but the
pcie_cap_regs_behavior[] array only covers up to PCI_EXP_RTSTA. Expand
this array to avoid walking off the end of it.
Do the same for pci_regs_behavior for consistency[], and add a
BUILD_BUG_ON() to also check the bridge->conf structure size.
Fixes: 23a5fba4d941 ("PCI: Introduce PCI bridge emulated config space common logic")
Link: https://lore.kernel.org/r/E1l6z9W-0006Re-MQ@rmk-PC.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d1cd163d0de22a4041a6f1aeabcf78f80076539 upstream.
According to PCI Express Base Specifications (rev 4.0, 6.6.1
"Conventional reset"), after fundamental reset a 100ms delay is needed
prior to enabling link training.
Update comment in code to reflect this requirement.
Link: https://lore.kernel.org/r/20201202184659.3795-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0c6a3475b033960e85ae2bf176b14cab0a627d2 upstream.
Move code which belongs to link training (delays and resets) into
advk_pcie_train_link() function, so everything related to link training,
including timings is at one place.
After experiments it can be observed that link training in aardvark
hardware is very sensitive to timings and delays, so it is a good idea to
have this code at the same place as link training calls.
This patch does not change behavior of aardvark initialization.
Link: https://lore.kernel.org/r/20200907111038.5811-6-pali@kernel.org
Tested-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b32c012e4b98f0126aa327be2d1f409963057643 upstream.
Include linux/gpio/consumer.h instead of linux/gpio.h, as is said in the
latter file.
This was reported by kernel test bot when compiling for s390.
drivers/pci/controller/pci-aardvark.c:350:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1074:21: error: implicit declaration of function 'devm_gpiod_get_from_of_node' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1076:14: error: use of undeclared identifier 'GPIOD_OUT_LOW'
Link: https://lore.kernel.org/r/202006211118.LxtENQfl%25lkp@intel.com
Link: https://lore.kernel.org/r/20200907111038.5811-2-pali@kernel.org
Fixes: 5169a9851daa ("PCI: aardvark: Issue PERST via GPIO")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70e380250c3621c55ff218cbaf2272830d9dbb1d upstream.
When there is no PCIe card connected and advk_pcie_rd_conf() or
advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
root bridge, the aardvark driver throws the following error message:
advk-pcie d0070000.pcie: config read/write timed out
Obviously accessing PCIe registers of disconnected card is not possible.
Extend check in advk_pcie_valid_device() function for validating
availability of PCIe bus. If PCIe link is down, then the device is marked
as Not Found and the driver does not try to access these registers.
This is just an optimization to prevent accessing PCIe registers when card
is disconnected. Trying to access PCIe registers of disconnected card does
not cause any crash, kernel just needs to wait for a timeout. So if card
disappear immediately after checking for PCIe link (before accessing PCIe
registers), it does not cause any problems.
Link: https://lore.kernel.org/r/20200702083036.12230-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96be36dbffacea0aa9e6ec4839583e79faa141a1 upstream.
PCI-E capability macros are already defined in linux/pci_regs.h.
Remove their reimplementation in pcie-aardvark.
Link: https://lore.kernel.org/r/20200430080625.26070-9-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5169a9851daaa2782a7bd2bb83d5b1bd224b2879 upstream.
Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).
Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.
If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.
It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.
Tested on Turris MOX.
Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 43fc679ced18006b12d918d7a8a4af392b7fbfe7 upstream.
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6964494582f56a3882c2c53b0edbfe99eb32b2e1 upstream.
Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).
Move the code which enables link training immediately before the one
which starts link traning.
This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.
Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
Fixes: f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready...")
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e078723f9cccd509482fd7f30a4afb1125ca7a2a upstream.
Initialise every multiple-byte field of emulated PCI bridge config
space with proper cpu_to_le* macro. This is required since the structure
describing config space of emulated bridge assumes little-endian
convention.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4c7d053d7f77cd5c1a1ba7c7ce085ddba13d1d7 upstream.
When configuring pcie reset pin from gpio (e.g. initially set by
u-boot) to pcie function this pin goes low for a brief moment
asserting the PERST# signal. Thus connected device enters fundamental
reset process and link configuration can only begin after a minimal
100ms delay (see [1]).
Because the pin configuration comes from the "default" pinctrl it is
implicitly configured before the probe callback is called:
driver_probe_device()
really_probe()
...
pinctrl_bind_pins() /* Here pin goes from gpio to PCIE reset
function and PERST# is asserted */
...
drv->probe()
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, 6.6.1 Conventional Reset
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67cb2a4c93499c2c22704998fd1fd2bc35194d8e upstream.
Avoid code repetition in advk_pcie_rd_conf() by handling errors with
goto jump, as is customary in kernel.
Link: https://lore.kernel.org/r/20211005180952.6812-9-kabel@kernel.org
Fixes: 43f5c77bcbd2 ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f21082fb20dbfb3e42b769b59ef21c2a7f2c7c1f upstream.
The ION AHCI device pretends that MSI masking isn't a thing, while it
actually implements it and needs MSIs to be unmasked to work. Add a quirk
to that effect.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/r/CALjTZvbzYfBuLB+H=fj2J+9=DxjQ2Uqcy0if_PvmJ-nU-qEgkg@mail.gmail.com
Link: https://lore.kernel.org/r/20211104180130.3825416-3-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2226667a145db2e1f314d7f57fd644fe69863ab9 upstream.
It appears that some devices are lying about their mask capability,
pretending that they don't have it, while they actually do.
The net result is that now that we don't enable MSIs on such
endpoint.
Add a new per-device flag to deal with this. Further patches will
make use of it, sadly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211104180130.3825416-2-maz@kernel.org
Cc: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3735459037114d31e5acd9894fad9aed104231a0 upstream.
free_msi_irqs() frees the MSI entries before destroying the sysfs entries
which are exposing them. Nothing prevents a concurrent free while a sysfs
file is read and accesses the possibly freed entry.
Move the sysfs release ahead of freeing the entries.
Fixes: 1c51b50c2995 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87sfw5305m.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d419052bc6c60fa4ab2b5a51d5f1e55a66e2b4ff ]
Commit 43f5c77bcbd2 ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org
Fixes: 43f5c77bcbd2 ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 464de7e7fff767e87429cd7be09c4f2cb50a6ccb ]
Use dev_dbg() instead of dev_err() in advk_pcie_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Link: https://lore.kernel.org/r/20211005180952.6812-4-kabel@kernel.org
Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 95997723b6402cd6c53e0f9e7ac640ec64eaaff8 upstream.
The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.
Link: https://lore.kernel.org/r/20211028185659.20329-4-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4313be1599d397625c14fb7826996813622decf upstream.
MSI domain callback .alloc() (implemented by advk_msi_irq_domain_alloc()
function) should return zero on success, since non-zero value indicates
failure.
When the driver was converted to generic MSI API in commit f21a8b1b6837
("PCI: aardvark: Move to MSI handling using generic MSI support"), it
was converted so that it returns hwirq number.
Fix this.
Link: https://lore.kernel.org/r/20211028185659.20329-3-kabel@kernel.org
Fixes: f21a8b1b6837 ("PCI: aardvark: Move to MSI handling using generic MSI support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b650b7ff20eb7ea8ef9031d20fb657286ab90cc upstream.
Add support for reporting PCI_EXP_LNKSTA_DLLLA bit in Link Control register
on emulated bridge via current LTSSM state. Also correctly indicate DLLLA
capability via PCI_EXP_LNKCAP_DLLLARC bit in Link Control Capability
register.
Link: https://lore.kernel.org/r/20211005180952.6812-14-kabel@kernel.org
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1fb95d7d3c7a926b002fe8a6bd27a1cb428b46dc upstream.
There are lot of undocumented interrupt bits. To prevent unwanted
spurious interrupts, fix all *_ALL_MASK macros to define all interrupt
bits, so that driver can properly mask all interrupts, including those
which are undocumented.
Link: https://lore.kernel.org/r/20211005180952.6812-8-kabel@kernel.org
Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
