summaryrefslogtreecommitdiff
path: root/drivers/pci
AgeCommit message (Collapse)Author
2017-07-27PCI/PM: Restore the status of PCI devices across hibernationChen Yu
commit e60514bd4485c0c7c5a7cf779b200ce0b95c70d6 upstream. Currently we saw a lot of "No irq handler" errors during hibernation, which caused the system hang finally: ata4.00: qc timeout (cmd 0xec) ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata4.00: revalidation failed (errno=-5) ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300) do_IRQ: 31.151 No irq handler for vector According to above logs, there is an interrupt triggered and it is dispatched to CPU31 with a vector number 151, but there is no handler for it, thus this IRQ will not get acked and will cause an IRQ flood which kills the system. To be more specific, the 31.151 is an interrupt from the AHCI host controller. After some investigation, the reason why this issue is triggered is because the thaw_noirq() function does not restore the MSI/MSI-X settings across hibernation. The scenario is illustrated below: 1. Before hibernation, IRQ 34 is the handler for the AHCI device, which is bound to CPU31. 2. Hibernation starts, the AHCI device is put into low power state. 3. All the nonboot CPUs are put offline, so IRQ 34 has to be migrated to the last alive one - CPU0. 4. After the snapshot has been created, all the nonboot CPUs are brought up again; IRQ 34 remains bound to CPU0. 5. AHCI devices are put into D0. 6. The snapshot is written to the disk. The issue is triggered in step 6. The AHCI interrupt should be delivered to CPU0, however it is delivered to the original CPU31 instead, which causes the "No irq handler" issue. Ying Huang has provided a clue that, in step 3 it is possible that writing to the register might not take effect as the PCI devices have been suspended. In step 3, the IRQ 34 affinity should be modified from CPU31 to CPU0, but in fact it is not. In __pci_write_msi_msg(), if the device is already in low power state, the low level MSI message entry will not be updated but cached. During the device restore process after a normal suspend/resume, pci_restore_msi_state() writes the cached MSI back to the hardware. But this is not the case for hibernation. pci_restore_msi_state() is not currently called in pci_pm_thaw_noirq(), although pci_save_state() has saved the necessary PCI cached information in pci_pm_freeze_noirq(). Restore the PCI status for the device during hibernation. Otherwise the status might be lost across hibernation (for example, settings for MSI, MSI-X, ATS, ACS, IOV, etc.), which might cause problems during hibernation. Suggested-by: Ying Huang <ying.huang@intel.com> Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Chen Yu <yu.c.chen@intel.com> [bhelgaas: changelog] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Len Brown <len.brown@intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Rui Zhang <rui.zhang@intel.com> Cc: Ying Huang <ying.huang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-25PCI: Freeze PME scan before suspending devicesLukas Wunner
commit ea00353f36b64375518662a8ad15e39218a1f324 upstream. Laurent Pinchart reported that the Renesas R-Car H2 Lager board (r8a7790) crashes during suspend tests. Geert Uytterhoeven managed to reproduce the issue on an M2-W Koelsch board (r8a7791): It occurs when the PME scan runs, once per second. During PME scan, the PCI host bridge (rcar-pci) registers are accessed while its module clock has already been disabled, leading to the crash. One reproducer is to configure s2ram to use "s2idle" instead of "deep" suspend: # echo 0 > /sys/module/printk/parameters/console_suspend # echo s2idle > /sys/power/mem_sleep # echo mem > /sys/power/state Another reproducer is to write either "platform" or "processors" to /sys/power/pm_test. It does not (or is less likely) to happen during full system suspend ("core" or "none") because system suspend also disables timers, and thus the workqueue handling PME scans no longer runs. Geert believes the issue may still happen in the small window between disabling module clocks and disabling timers: # echo 0 > /sys/module/printk/parameters/console_suspend # echo platform > /sys/power/pm_test # Or "processors" # echo mem > /sys/power/state (Make sure CONFIG_PCI_RCAR_GEN2 and CONFIG_USB_OHCI_HCD_PCI are enabled.) Rafael Wysocki agrees that PME scans should be suspended before the host bridge registers become inaccessible. To that end, queue the task on a workqueue that gets frozen before devices suspend. Rafael notes however that as a result, some wakeup events may be missed if they are delivered via PME from a device without working IRQ (which hence must be polled) and occur after the workqueue has been frozen. If that turns out to be an issue in practice, it may be possible to solve it by calling pci_pme_list_scan() once directly from one of the host bridge's pm_ops callbacks. Stacktrace for posterity: PM: Syncing filesystems ... [ 38.566237] done. PM: Preparing system for sleep (mem) Freezing user space processes ... [ 38.579813] (elapsed 0.001 seconds) done. Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. PM: Suspending system (mem) PM: suspend of devices complete after 152.456 msecs PM: late suspend of devices complete after 2.809 msecs PM: noirq suspend of devices complete after 29.863 msecs suspend debug: Waiting for 5 second(s). Unhandled fault: asynchronous external abort (0x1211) at 0x00000000 pgd = c0003000 [00000000] *pgd=80000040004003, *pmd=00000000 Internal error: : 1211 [#1] SMP ARM Modules linked in: CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 4.9.0-rc1-koelsch-00011-g68db9bc814362e7f #3383 Hardware name: Generic R8A7791 (Flattened Device Tree) Workqueue: events pci_pme_list_scan task: eb56e140 task.stack: eb58e000 PC is at pci_generic_config_read+0x64/0x6c LR is at rcar_pci_cfg_base+0x64/0x84 pc : [<c041d7b4>] lr : [<c04309a0>] psr: 600d0093 sp : eb58fe98 ip : c041d750 fp : 00000008 r10: c0e2283c r9 : 00000000 r8 : 600d0013 r7 : 00000008 r6 : eb58fed6 r5 : 00000002 r4 : eb58feb4 r3 : 00000000 r2 : 00000044 r1 : 00000008 r0 : 00000000 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user Control: 30c5387d Table: 6a9f6c80 DAC: 55555555 Process kworker/1:1 (pid: 20, stack limit = 0xeb58e210) Stack: (0xeb58fe98 to 0xeb590000) fe80: 00000002 00000044 fea0: eb6f5800 c041d9b0 eb58feb4 00000008 00000044 00000000 eb78a000 eb78a000 fec0: 00000044 00000000 eb9aff00 c0424bf0 eb78a000 00000000 eb78a000 c0e22830 fee0: ea8a6fc0 c0424c5c eaae79c0 c0424ce0 eb55f380 c0e22838 eb9a9800 c0235fbc ff00: eb55f380 c0e22838 eb55f380 eb9a9800 eb9a9800 eb58e000 eb9a9824 c0e02100 ff20: eb55f398 c02366c4 eb56e140 eb5631c0 00000000 eb55f380 c023641c 00000000 ff40: 00000000 00000000 00000000 c023a928 cd105598 00000000 40506a34 eb55f380 ff60: 00000000 00000000 dead4ead ffffffff ffffffff eb58ff74 eb58ff74 00000000 ff80: 00000000 dead4ead ffffffff ffffffff eb58ff90 eb58ff90 eb58ffac eb5631c0 ffa0: c023a844 00000000 00000000 c0206d68 00000000 00000000 00000000 00000000 ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 3a81336c 10ccd1dd [<c041d7b4>] (pci_generic_config_read) from [<c041d9b0>] (pci_bus_read_config_word+0x58/0x80) [<c041d9b0>] (pci_bus_read_config_word) from [<c0424bf0>] (pci_check_pme_status+0x34/0x78) [<c0424bf0>] (pci_check_pme_status) from [<c0424c5c>] (pci_pme_wakeup+0x28/0x54) [<c0424c5c>] (pci_pme_wakeup) from [<c0424ce0>] (pci_pme_list_scan+0x58/0xb4) [<c0424ce0>] (pci_pme_list_scan) from [<c0235fbc>] (process_one_work+0x1bc/0x308) [<c0235fbc>] (process_one_work) from [<c02366c4>] (worker_thread+0x2a8/0x3e0) [<c02366c4>] (worker_thread) from [<c023a928>] (kthread+0xe4/0xfc) [<c023a928>] (kthread) from [<c0206d68>] (ret_from_fork+0x14/0x2c) Code: ea000000 e5903000 f57ff04f e3a00000 (e5843000) ---[ end trace 667d43ba3aa9e589 ]--- Fixes: df17e62e5bff ("PCI: Add support for polling PME state on suspended legacy PCI devices") Reported-and-tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reported-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Cc: Simon Horman <horms+renesas@verge.net.au> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-25PCI: Fix pci_mmap_fits() for HAVE_PCI_RESOURCE_TO_USER platformsDavid Woodhouse
commit 6bccc7f426abd640f08d8c75fb22f99483f201b4 upstream. In the PCI_MMAP_PROCFS case when the address being passed by the user is a 'user visible' resource address based on the bus window, and not the actual contents of the resource, that's what we need to be checking it against. Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-30PCI: Do any VF BAR updates before enabling the BARsSumit Semwal
From: Gavin Shan <gwshan@linux.vnet.ibm.com> [ Upstream commit f40ec3c748c6912f6266c56a7f7992de61b255ed ] Previously we enabled VFs and enable their memory space before calling pcibios_sriov_enable(). But pcibios_sriov_enable() may update the VF BARs: for example, on PPC PowerNV we may change them to manage the association of VFs to PEs. Because 64-bit BARs cannot be updated atomically, it's unsafe to update them while they're enabled. The half-updated state may conflict with other devices in the system. Call pcibios_sriov_enable() before enabling the VFs so any BAR updates happen while the VF BARs are disabled. [bhelgaas: changelog] Tested-by: Carol Soto <clsoto@us.ibm.com> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-30PCI: Ignore BAR updates on virtual functionsSumit Semwal
From: Bjorn Helgaas <bhelgaas@google.com> [ Upstream commit 63880b230a4af502c56dde3d4588634c70c66006 ] VF BARs are read-only zero, so updating VF BARs will not have any effect. See the SR-IOV spec r1.1, sec 3.4.1.11. We already ignore these updates because of 70675e0b6a1a ("PCI: Don't try to restore VF BARs"); this merely restructures it slightly to make it easier to split updates for standard and SR-IOV BARs. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-30PCI: Update BARs using property bits appropriate for typeSumit Semwal
From: Bjorn Helgaas <bhelgaas@google.com> [ Upstream commit 45d004f4afefdd8d79916ee6d97a9ecd94bb1ffe ] The BAR property bits (0-3 for memory BARs, 0-1 for I/O BARs) are supposed to be read-only, but we do save them in res->flags and include them when updating the BAR. Mask the I/O property bits with ~PCI_BASE_ADDRESS_IO_MASK (0x3) instead of PCI_REGION_FLAG_MASK (0xf) to make it obvious that we can't corrupt bits 2-3 of I/O addresses. Use PCI_ROM_ADDRESS_MASK for ROM BARs. This means we'll only check the top 21 bits (instead of the 28 bits we used to check) of a ROM BAR to see if the update was successful. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-30PCI: Don't update VF BARs while VF memory space is enabledSumit Semwal
From: Bjorn Helgaas <bhelgaas@google.com> [ Upstream commit 546ba9f8f22f71b0202b6ba8967be5cc6dae4e21 ] If we update a VF BAR while it's enabled, there are two potential problems: 1) Any driver that's using the VF has a cached BAR value that is stale after the update, and 2) We can't update 64-bit BARs atomically, so the intermediate state (new lower dword with old upper dword) may conflict with another device, and an access by a driver unrelated to the VF may cause a bus error. Warn about attempts to update VF BARs while they are enabled. This is a programming error, so use dev_WARN() to get a backtrace. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-30PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLESumit Semwal
From: Bjorn Helgaas <bhelgaas@google.com> [ Upstream commit 7a6d312b50e63f598f5b5914c4fd21878ac2b595 ] Remove the assumption that IORESOURCE_ROM_ENABLE == PCI_ROM_ADDRESS_ENABLE. PCI_ROM_ADDRESS_ENABLE is the ROM enable bit defined by the PCI spec, so if we're reading or writing a BAR register value, that's what we should use. IORESOURCE_ROM_ENABLE is a corresponding bit in struct resource flags. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-30PCI: Add comments about ROM BAR updatingSumit Semwal
From: Bjorn Helgaas <bhelgaas@google.com> [ Upstream commit 0b457dde3cf8b7c76a60f8e960f21bbd4abdc416 ] pci_update_resource() updates a hardware BAR so its address matches the kernel's struct resource UNLESS it's a disabled ROM BAR. We only update those when we enable the ROM. It's not obvious from the code why ROM BARs should be handled specially. Apparently there are Matrox devices with defective ROM BARs that read as zero when disabled. That means that if pci_enable_rom() reads the disabled BAR, sets PCI_ROM_ADDRESS_ENABLE (without re-inserting the address), and writes it back, it would enable the ROM at address zero. Add comments and references to explain why we can't make the code look more rational. The code changes are from 755528c860b0 ("Ignore disabled ROM resources at setup") and 8085ce084c0f ("[PATCH] Fix PCI ROM mapping"). Link: https://lkml.org/lkml/2005/8/30/138 Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [sumits: minor fixup in rom.c for 4.4.y] Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-30PCI: Remove pci_resource_bar() and pci_iov_resource_bar()Sumit Semwal
From: Bjorn Helgaas <bhelgaas@google.com> [ Upstream commit 286c2378aaccc7343ebf17ec6cd86567659caf70 ] pci_std_update_resource() only deals with standard BARs, so we don't have to worry about the complications of VF BARs in an SR-IOV capability. Compute the BAR address inline and remove pci_resource_bar(). That makes pci_iov_resource_bar() unused, so remove that as well. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-30PCI: Separate VF BAR updates from standard BAR updatesSumit Semwal
From: Bjorn Helgaas <bhelgaas@google.com> [ Upstream commit 6ffa2489c51da77564a0881a73765ea2169f955d ] Previously pci_update_resource() used the same code path for updating standard BARs and VF BARs in SR-IOV capabilities. Split the VF BAR update into a new pci_iov_update_resource() internal interface, which makes it simpler to compute the BAR address (we can get rid of pci_resource_bar() and pci_iov_resource_bar()). This patch: - Renames pci_update_resource() to pci_std_update_resource(), - Adds pci_iov_update_resource(), - Makes pci_update_resource() a wrapper that calls the appropriate one, No functional change intended. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-09PCI/ASPM: Handle PCI-to-PCIe bridges as roots of PCIe hierarchiesBjorn Helgaas
commit 030305d69fc6963c16003f50d7e8d74b02d0a143 upstream. In a struct pcie_link_state, link->root points to the pcie_link_state of the root of the PCIe hierarchy. For the topmost link, this points to itself (link->root = link). For others, we copy the pointer from the parent (link->root = link->parent->root). Previously we recognized that Root Ports originated PCIe hierarchies, but we treated PCI/PCI-X to PCIe Bridges as being in the middle of the hierarchy, and when we tried to copy the pointer from link->parent->root, there was no parent, and we dereferenced a NULL pointer: BUG: unable to handle kernel NULL pointer dereference at 0000000000000090 IP: [<ffffffff9e424350>] pcie_aspm_init_link_state+0x170/0x820 Recognize that PCI/PCI-X to PCIe Bridges originate PCIe hierarchies just like Root Ports do, so link->root for these devices should also point to itself. Fixes: 51ebfc92b72b ("PCI: Enumerate switches below PCI-to-PCIe bridges") Link: https://bugzilla.kernel.org/show_bug.cgi?id=193411 Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1022181 Tested-by: lists@ssl-mail.com Tested-by: Jayachandran C. <jnair@caviumnetworks.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-26PCI: Enumerate switches below PCI-to-PCIe bridgesBjorn Helgaas
commit 51ebfc92b72b4f7dac1ab45683bf56741e454b8c upstream. A PCI-to-PCIe bridge (a "reverse bridge") has a PCI or PCI-X primary interface and a PCI Express secondary interface. The PCIe interface is a Downstream Port that originates a Link. See the "PCI Express to PCI/PCI-X Bridge Specification", rev 1.0, sections 1.2 and A.6. The bug report below involves a PCI-to-PCIe bridge and a PCIe switch below the bridge: 00:1e.0 Intel 82801 PCI Bridge to [bus 01-0a] 01:00.0 Pericom PI7C9X111SL PCIe-to-PCI Reversible Bridge to [bus 02-0a] 02:00.0 Pericom Device 8608 [PCIe Upstream Port] to [bus 03-0a] 03:01.0 Pericom Device 8608 [PCIe Downstream Port] to [bus 0a] 01:00.0 is configured as a PCI-to-PCIe bridge (despite the name printed by lspci). As we traverse a PCIe hierarchy, device connections alternate between PCIe Links and internal Switch logic. Previously we did not recognize that 01:00.0 had a secondary link, so we thought the 02:00.0 Upstream Port *did* have a secondary link. In fact, it's the other way around: 01:00.0 has a secondary link, and 02:00.0 has internal Switch logic on its secondary side. When we thought 02:00.0 had a secondary link, the pci_scan_slot() -> only_one_child() path assumed 02:00.0 could have only one child, so 03:00.0 was the only possible downstream device. But 03:00.0 doesn't exist, so we didn't look for any other devices on bus 03. Booting with "pci=pcie_scan_all" is a workaround, but we don't want users to have to do that. Recognize that PCI-to-PCIe bridges originate links on their secondary interfaces. Link: https://bugzilla.kernel.org/show_bug.cgi?id=189361 Fixes: d0751b98dfa3 ("PCI: Add dev->has_secondary_link to track downstream PCIe links") Tested-by: Blake Moore <blake.moore@men.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-12powerpc/pci/rpadlpar: Fix device reference leaksJohan Hovold
commit 99e5cde5eae78bef95bfe7c16ccda87fb070149b upstream. Make sure to drop any device reference taken by vio_find_node() when adding and removing virtual I/O slots. Fixes: 5eeb8c63a38f ("[PATCH] PCI Hotplug: rpaphp: Move VIO registration") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-09PCI: Check for PME in targeted sleep stateAlan Stern
commit 6496ebd7edf446fccf8266a1a70ffcb64252593e upstream. One some systems, the firmware does not allow certain PCI devices to be put in deep D-states. This can cause problems for wakeup signalling, if the device does not support PME# in the deepest allowed suspend state. For example, Pierre reports that on his system, ACPI does not permit his xHCI host controller to go into D3 during runtime suspend -- but D3 is the only state in which the controller can generate PME# signals. As a result, the controller goes into runtime suspend but never wakes up, so it doesn't work properly. USB devices plugged into the controller are never detected. If the device relies on PME# for wakeup signals but is not capable of generating PME# in the target state, the PCI core should accurately report that it cannot do wakeup from runtime suspend. This patch modifies the pci_dev_run_wake() routine to add this check. Reported-by: Pierre de Villemereuil <flyos@mailoo.org> Tested-by: Pierre de Villemereuil <flyos@mailoo.org> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: Lukas Wunner <lukas@wunner.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-08PCI: Set Read Completion Boundary to 128 iff Root Port supports it (_HPX)Johannes Thumshirn
commit e42010d8207f9d15a605ceb8e321bcd9648071b0 upstream. Per PCIe spec r3.0, sec 2.3.1.1, the Read Completion Boundary (RCB) determines the naturally aligned address boundaries on which a Read Request may be serviced with multiple Completions: - For a Root Complex, RCB is 64 bytes or 128 bytes This value is reported in the Link Control Register Note: Bridges and Endpoints may implement a corresponding command bit which may be set by system software to indicate the RCB value for the Root Complex, allowing the Bridge/Endpoint to optimize its behavior when the Root Complex’s RCB is 128 bytes. - For all other system elements, RCB is 128 bytes Per sec 7.8.7, if a Root Port only supports a 64-byte RCB, the RCB of all downstream devices must be clear, indicating an RCB of 64 bytes. If the Root Port supports a 128-byte RCB, we may optionally set the RCB of downstream devices so they know they can generate larger Completions. Some BIOSes supply an _HPX that tells us to set RCB, even though the Root Port doesn't have RCB set, which may lead to Malformed TLP errors if the Endpoint generates completions larger than the Root Port can handle. The IBM x3850 X6 with BIOS version -[A8E120CUS-1.30]- 08/22/2016 supplies such an _HPX and a Mellanox MT27500 ConnectX-3 device fails to initialize: mlx4_core 0000:41:00.0: command 0xfff timed out (go bit not cleared) mlx4_core 0000:41:00.0: device is going to be reset mlx4_core 0000:41:00.0: Failed to obtain HW semaphore, aborting mlx4_core 0000:41:00.0: Fail to reset HCA ------------[ cut here ]------------ kernel BUG at drivers/net/ethernet/mellanox/mlx4/catas.c:193! After 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration") and 7a1562d4f2d0 ("PCI: Apply _HPX Link Control settings to all devices with a link"), we apply _HPX settings to *all* devices, not just those hot-added after boot. Before 7a1562d4f2d0, we didn't touch the Mellanox RCB, and the device worked. After 7a1562d4f2d0, we set its RCB to 128, and it failed. Set the RCB to 128 iff the Root Port supports a 128-byte RCB. Otherwise, set RCB to 64 bytes. This effectively ignores what _HPX tells us about RCB. Note that this change only affects _HPX handling. If we have no _HPX, this does nothing with RCB. [bhelgaas: changelog, clear RCB if not set for Root Port] Fixes: 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration") Fixes: 7a1562d4f2d0 ("PCI: Apply _HPX Link Control settings to all devices with a link") Link: https://bugzilla.kernel.org/show_bug.cgi?id=187781 Tested-by: Frank Danapfel <fdanapfe@redhat.com> Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-08PCI: Export pcie_find_root_portJohannes Thumshirn
commit e784930bd645e7df78c66e7872fec282b0620075 upstream. Export pcie_find_root_port() so we can use it outside of PCIe-AER error injection. Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-28PCI: Mark Atheros AR9580 to avoid bus resetMaik Broemme
commit 8e2e03179923479ca0c0b6fdc7c93ecf89bce7a8 upstream. Similar to the AR93xx and the AR94xx series, the AR95xx also have the same quirk for the Bus Reset. It will lead to instant system reset if the device is assigned via VFIO to a KVM VM. I've been able reproduce this behavior with a MikroTik R11e-2HnD. Fixes: c3e59ee4e766 ("PCI: Mark Atheros AR93xx to avoid bus reset") Signed-off-by: Maik Broemme <mbroemme@libmpq.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-07genirq/msi: Make sure PCI MSIs are activated earlyMarc Zyngier
commit f3b0946d629c8bfbd3e5f038e30cb9c711a35f10 upstream. Bharat Kumar Gogada reported issues with the generic MSI code, where the end-point ended up with garbage in its MSI configuration (both for the vector and the message). It turns out that the two MSI paths in the kernel are doing slightly different things: generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI And it turns out that end-points are allowed to latch the content of the MSI configuration registers as soon as MSIs are enabled. In Bharat's case, the end-point ends up using whatever was there already, which is not what you want. In order to make things converge, we introduce a new MSI domain flag (MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set, this flag forces the programming of the end-point as soon as the MSIs are allocated. A consequence of this is that we have an extra activate in irq_startup, but that should be without much consequence. tglx: - Several people reported a VMWare regression with PCI/MSI-X passthrough. It turns out that the patch also cures that issue. - We need to have a look at the MSI disable interrupt path, where we write the msg to all zeros without disabling MSI in the PCI device. Is that correct? Fixes: 52f518a3a7c2 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts" Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com> Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru> Reported-by: Matthias Prager <linux@matthiasprager.de> Reported-by: Jason Taylor <jason.taylor@simplivity.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: linux-pci@vger.kernel.org Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-07PCI: Limit config space size for Netronome NFP4000Simon Horman
commit c2e771b02792d222cbcd9617fe71482a64f52647 upstream. Like the NFP6000, the NFP4000 as an erratum where reading/writing to PCI config space addresses above 0x600 can cause the NFP to generate PCIe completion timeouts. Limit the NFP4000's PF's config space size to 0x600 bytes as is already done for the NFP6000. The NFP4000's VF is 0x6004 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same device ID as the NFP6000's VF. Thus, its config space is already limited by the existing use of quirk_nfp6000(). Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-07PCI: Limit config space size for Netronome NFP6000 familyJason S. McMullan
commit 9f33a2ae59f24452c1076749deb615bccd435ca9 upstream. The NFP6000 has an erratum where reading/writing to PCI config space addresses above 0x600 can cause the NFP to generate PCIe completion timeouts. Limit the NFP6000's config space size to 0x600 bytes. Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com> [simon: edited changelog] Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-07PCI: Support PCIe devices with short cfg_sizeJason S. McMullan
commit c20aecf6963d1273d8f6d61c042b4845441ca592 upstream. If a device quirk modifies the pci_dev->cfg_size to be less than PCI_CFG_SPACE_EXP_SIZE (4096), but greater than PCI_CFG_SPACE_SIZE (256), the PCI sysfs interface truncates the readable size to PCI_CFG_SPACE_SIZE. Allow sysfs access to config space up to cfg_size, even if the device doesn't support the entire 4096-byte PCIe config space. Note that pci_read_config() and pci_write_config() limit access to dev->cfg_size even though pcie_config_attr contains 4096 (the maximum size). Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com> [simon: edited changelog] Signed-off-by: Simon Horman <simon.horman@netronome.com> [bhelgaas: more changelog edits] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-20PCI: Mark Atheros AR9485 and QCA9882 to avoid bus resetChris Blake
commit 9ac0108c2bac3f1d0255f64fb89fc27e71131b24 upstream. Similar to the AR93xx series, the AR94xx and the Qualcomm QCA988x also have the same quirk for the Bus Reset. Fixes: c3e59ee4e766 ("PCI: Mark Atheros AR93xx to avoid bus reset") Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-07PCI: Disable all BAR sizing for devices with non-compliant BARsPrarit Bhargava
commit ad67b437f187ea818b2860524d10f878fadfdd99 upstream. b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with the PCI spec. But it didn't do anything for expansion ROM BARs, so we still try to size them, resulting in warnings like this on Broadwell-EP: pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref] Move the non-compliant BAR check from __pci_read_base() up to pci_read_bases() so it applies to the expansion ROM BAR as well as to BARs 0-5. Note that direct callers of __pci_read_base(), like sriov_init(), will now bypass this check. We haven't had reports of devices with broken SR-IOV BARs yet. [bhelgaas: changelog] Fixes: b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Thomas Gleixner <tglx@linutronix.de> CC: Ingo Molnar <mingo@redhat.com> CC: "H. Peter Anvin" <hpa@zytor.com> CC: Andi Kleen <ak@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-12PCI: Disable IO/MEM decoding for devices with non-compliant BARsBjorn Helgaas
commit b84106b4e2290c081cdab521fa832596cdfea246 upstream. The PCI config header (first 64 bytes of each device's config space) is defined by the PCI spec so generic software can identify the device and manage its usage of I/O, memory, and IRQ resources. Some non-spec-compliant devices put registers other than BARs where the BARs should be. When the PCI core sizes these "BARs", the reads and writes it does may have unwanted side effects, and the "BAR" may appear to describe non-sensical address space. Add a flag bit to mark non-compliant devices so we don't touch their BARs. Turn off IO/MEM decoding to prevent the devices from consuming address space, since we can't read the BARs to find out what that address space would be. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-16PCI: Allow a NULL "parent" pointer in pci_bus_assign_domain_nr()Krzysztof Hałasa
commit 54c6e2dd00c313d0add58e5befe62fe6f286d03b upstream. pci_create_root_bus() passes a "parent" pointer to pci_bus_assign_domain_nr(). When CONFIG_PCI_DOMAINS_GENERIC is defined, pci_bus_assign_domain_nr() dereferences that pointer. Many callers of pci_create_root_bus() supply a NULL "parent" pointer, which leads to a NULL pointer dereference error. 7c674700098c ("PCI: Move domain assignment from arm64 to generic code") moved the "parent" dereference from arm64 to generic code. Only arm64 used that code (because only arm64 defined CONFIG_PCI_DOMAINS_GENERIC), and it always supplied a valid "parent" pointer. Other arches supplied NULL "parent" pointers but didn't defined CONFIG_PCI_DOMAINS_GENERIC, so they used a no-op version of pci_bus_assign_domain_nr(). 8c7d14746abc ("ARM/PCI: Move to generic PCI domains") defined CONFIG_PCI_DOMAINS_GENERIC on ARM, and many ARM platforms use pci_common_init(), which supplies a NULL "parent" pointer. These platforms (cns3xxx, dove, footbridge, iop13xx, etc.) crash with a NULL pointer dereference like this while probing PCI: Unable to handle kernel NULL pointer dereference at virtual address 000000a4 PC is at pci_bus_assign_domain_nr+0x10/0x84 LR is at pci_create_root_bus+0x48/0x2e4 Kernel panic - not syncing: Attempted to kill init! [bhelgaas: changelog, add "Reported:" and "Fixes:" tags] Reported: http://forum.doozan.com/read.php?2,17868,22070,quote=1 Fixes: 8c7d14746abc ("ARM/PCI: Move to generic PCI domains") Fixes: 7c674700098c ("PCI: Move domain assignment from arm64 to generic code") Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-09PCI: keystone: Fix MSI code that retrieves struct pcie_port pointerMurali Karicheri
commit 79e3f4a853ed161cd4c06d84b50beebf961a47c6 upstream. Commit cbce7900598c ("PCI: designware: Make driver arch-agnostic") changed the host bridge sysdata pointer from the ARM pci_sys_data to the DesignWare pcie_port structure, and changed pcie-designware.c to reflect that. But it did not change the corresponding code in pci-keystone-dw.c, so it caused crashes on Keystone: Unable to handle kernel NULL pointer dereference at virtual address 00000030 pgd = c0003000 [00000030] *pgd=80000800004003, *pmd=00000000 Internal error: Oops: 206 [#1] PREEMPT SMP ARM CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.2-00139-gb74f926 #2 Hardware name: Keystone PC is at ks_dw_pcie_msi_irq_unmask+0x24/0x58 Change pci-keystone-dw.c to expect sysdata to be the struct pcie_port pointer. [bhelgaas: changelog] Fixes: cbce7900598c ("PCI: designware: Make driver arch-agnostic") Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03xen/pcifront: Fix mysterious crashes when NUMA locality information was ↵Konrad Rzeszutek Wilk
extracted. commit 4d8c8bd6f2062c9988817183a91fe2e623c8aa5e upstream. Occasionaly PV guests would crash with: pciback 0000:00:00.1: Xen PCI mapped GSI0 to IRQ16 BUG: unable to handle kernel paging request at 0000000d1a8c0be0 .. snip.. <ffffffff8139ce1b>] find_next_bit+0xb/0x10 [<ffffffff81387f22>] cpumask_next_and+0x22/0x40 [<ffffffff813c1ef8>] pci_device_probe+0xb8/0x120 [<ffffffff81529097>] ? driver_sysfs_add+0x77/0xa0 [<ffffffff815293e4>] driver_probe_device+0x1a4/0x2d0 [<ffffffff813c1ddd>] ? pci_match_device+0xdd/0x110 [<ffffffff81529657>] __device_attach_driver+0xa7/0xb0 [<ffffffff815295b0>] ? __driver_attach+0xa0/0xa0 [<ffffffff81527622>] bus_for_each_drv+0x62/0x90 [<ffffffff8152978d>] __device_attach+0xbd/0x110 [<ffffffff815297fb>] device_attach+0xb/0x10 [<ffffffff813b75ac>] pci_bus_add_device+0x3c/0x70 [<ffffffff813b7618>] pci_bus_add_devices+0x38/0x80 [<ffffffff813dc34e>] pcifront_scan_root+0x13e/0x1a0 [<ffffffff817a0692>] pcifront_backend_changed+0x262/0x60b [<ffffffff814644c6>] ? xenbus_gather+0xd6/0x160 [<ffffffff8120900f>] ? put_object+0x2f/0x50 [<ffffffff81465c1d>] xenbus_otherend_changed+0x9d/0xa0 [<ffffffff814678ee>] backend_changed+0xe/0x10 [<ffffffff81463a28>] xenwatch_thread+0xc8/0x190 [<ffffffff810f22f0>] ? woken_wake_function+0x10/0x10 which was the result of two things: When we call pci_scan_root_bus we would pass in 'sd' (sysdata) pointer which was an 'pcifront_sd' structure. However in the pci_device_add it expects that the 'sd' is 'struct sysdata' and sets the dev->node to what is in sd->node (offset 4): set_dev_node(&dev->dev, pcibus_to_node(bus)); __pcibus_to_node(const struct pci_bus *bus) { const struct pci_sysdata *sd = bus->sysdata; return sd->node; } However our structure was pcifront_sd which had nothing at that offset: struct pcifront_sd { int domain; /* 0 4 */ /* XXX 4 bytes hole, try to pack */ struct pcifront_device * pdev; /* 8 8 */ } That is an hole - filled with garbage as we used kmalloc instead of kzalloc (the second problem). This patch fixes the issue by: 1) Use kzalloc to initialize to a well known state. 2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That way access to the 'node' will access the right offset. Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03PCI/AER: Flush workqueue on device remove to avoid use-after-freeSebastian Andrzej Siewior
commit 4ae2182b1e3407de369f8c5d799543b7db74221b upstream. A Root Port's AER structure (rpc) contains a queue of events. aer_irq() enqueues AER status information and schedules aer_isr() to dequeue and process it. When we remove a device, aer_remove() waits for the queue to be empty, then frees the rpc struct. But aer_isr() references the rpc struct after dequeueing and possibly emptying the queue, which can cause a use-after-free error as in the following scenario with two threads, aer_isr() on the left and a concurrent aer_remove() on the right: Thread A Thread B -------- -------- aer_irq(): rpc->prod_idx++ aer_remove(): wait_event(rpc->prod_idx == rpc->cons_idx) # now blocked until queue becomes empty aer_isr(): # ... rpc->cons_idx++ # unblocked because queue is now empty ... kfree(rpc) mutex_unlock(&rpc->rpc_mutex) To prevent this problem, use flush_work() to wait until the last scheduled instance of aer_isr() has completed before freeing the rpc struct in aer_remove(). I reproduced this use-after-free by flashing a device FPGA and re-enumerating the bus to find the new device. With SLUB debug, this crashes with 0x6b bytes (POISON_FREE, the use-after-free magic number) in GPR25: pcieport 0000:00:00.0: AER: Multiple Corrected error received: id=0000 Unable to handle kernel paging request for data at address 0x27ef9e3e Workqueue: events aer_isr GPR24: dd6aa000 6b6b6b6b 605f8378 605f8360 d99b12c0 604fc674 606b1704 d99b12c0 NIP [602f5328] pci_walk_bus+0xd4/0x104 [bhelgaas: changelog, stable tag] Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-03ACPI / PCI / hotplug: unlock in error path in acpiphp_enable_slot()Insu Yun
commit 2c3033a0664dfae91e1dee7fabac10f24354b958 upstream. In acpiphp_enable_slot(), there is a missing unlock path when error occurred. It needs to be unlocked before returning an error. Signed-off-by: Insu Yun <wuninsu@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-02-17PCI: Fix minimum allocation address overwriteChristoph Biedl
commit 3460baa620685c20f5ee19afb6d99d26150c382c upstream. Commit 36e097a8a297 ("PCI: Split out bridge window override of minimum allocation address") claimed to do no functional changes but unfortunately did: The "min" variable is altered. At least the AVM A1 PCMCIA adapter was no longer detected, breaking ISDN operation. Use a local copy of "min" to restore the previous behaviour. [bhelgaas: avoid gcc "?:" extension for portability and readability] Fixes: 36e097a8a297 ("PCI: Split out bridge window override of minimum allocation address") Signed-off-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-02-17PCI: host: Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREADGrygorii Strashko
commit 8ff0ef996ca00028519c70e8d51d32bd37eb51dc upstream. On -RT and if kernel is booting with "threadirqs" cmd line parameter, PCIe/PCI (MSI) IRQ cascade handlers (like dra7xx_pcie_msi_irq_handler()) will be forced threaded and, as result, will generate warnings like this: WARNING: CPU: 1 PID: 82 at kernel/irq/handle.c:150 handle_irq_event_percpu+0x14c/0x174() irq 460 handler irq_default_primary_handler+0x0/0x14 enabled interrupts Backtrace: (warn_slowpath_common) from (warn_slowpath_fmt+0x38/0x40) (warn_slowpath_fmt) from (handle_irq_event_percpu+0x14c/0x174) (handle_irq_event_percpu) from (handle_irq_event+0x84/0xb8) (handle_irq_event) from (handle_simple_irq+0x90/0x118) (handle_simple_irq) from (generic_handle_irq+0x30/0x44) (generic_handle_irq) from (dra7xx_pcie_msi_irq_handler+0x7c/0x8c) (dra7xx_pcie_msi_irq_handler) from (irq_forced_thread_fn+0x28/0x5c) (irq_forced_thread_fn) from (irq_thread+0x128/0x204) This happens because all of them invoke generic_handle_irq() from the requested handler. generic_handle_irq() grabs raw_locks and thus needs to run in raw-IRQ context. This issue was originally reproduced on TI dra7-evem, but, as was identified during discussion [1], other hosts can also suffer from this issue. Fix all them at once by marking PCIe/PCI (MSI) IRQ cascade handlers IRQF_NO_THREAD explicitly. [1] http://lkml.kernel.org/r/1448027966-21610-1-git-send-email-grygorii.strashko@ti.com [bhelgaas: add stable tag, fix typos] Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Lucas Stach <l.stach@pengutronix.de> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Jingoo Han <jingoohan1@gmail.com> CC: Kukjin Kim <kgene@kernel.org> CC: Krzysztof Kozlowski <k.kozlowski@samsung.com> CC: Richard Zhu <Richard.Zhu@freescale.com> CC: Thierry Reding <thierry.reding@gmail.com> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Alexandre Courbot <gnurou@gmail.com> CC: Simon Horman <horms@verge.net.au> CC: Pratyush Anand <pratyush.anand@gmail.com> CC: Michal Simek <michal.simek@xilinx.com> CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com> CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-09Merge tag 'pci-v4.4-fixes-4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixlet from Bjorn Helgaas: "This marks the TI DRA7xx host bridge driver as broken. Apparently it has never worked without some additional out-of-tree code, so I'm going to mark it broken now and remove it completely next cycle unless it's fixed" * tag 'pci-v4.4-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: dra7xx: Mark driver as broken
2016-01-08PCI: dra7xx: Mark driver as brokenRichard Cochran
Mark the dra7xx PCI host driver as broken. This driver was first merged in v3.17 and has never worked. Although the driver compiles just fine, it is missing an essential device reset. If the driver is included, the kernel locks up hard shortly after booting, before any console output appears. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-12-31Merge tag 'pci-v4.4-fixes-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI bugfix from Bjorn Helgaas: "Here's another fix for v4.4. This fixes 32-bit config reads for the HiSilicon driver. Obviously the driver is completely broken without this fix (apparently it actually was tested internally, but got broken somehow in the process of upstreaming it). Summary: HiSilicon host bridge driver Fix 32-bit config reads (Dongdong Liu)" * tag 'pci-v4.4-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: hisi: Fix hisi_pcie_cfg_read() 32-bit reads
2015-12-09Merge tag 'pci-v4.4-fixes-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixes from Bjorn Helgaas: "These are more fixes I'd like to have in v4.4. Several for the Altera driver added for v4.4, and one for an MSI domain problem that affects several arm64 platforms: MSI: - Only use the generic MSI layer when domain is hierarchical (Marc Zyngier) Altera host bridge driver: - Fix loop in tlp_read_packet() (Dan Carpenter) - Fix Requester ID for config accesses (Ley Foon Tan) - Check TLP completion status (Ley Foon Tan) - Fix error when INTx is 4 (Ley Foon Tan)" * tag 'pci-v4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: altera: Fix error when INTx is 4 PCI: altera: Check TLP completion status PCI: altera: Fix Requester ID for config accesses PCI: altera: Fix loop in tlp_read_packet() PCI/MSI: Only use the generic MSI layer when domain is hierarchical
2015-12-04PCI: hisi: Fix hisi_pcie_cfg_read() 32-bit readsDongdong Liu
For 32-bit config reads (size == 4), hisi_pcie_cfg_read() returned success but never filled in the data we read. Return the register data for 32-bit config reads. Without this fix, PCI doesn't work at all because enumeration depends on 32-bit config reads. The driver was tested internally, but got broken in the process of upstreaming, so this fixes the breakage. Fixes: 500a1d9a43e0 ("PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver") Signed-off-by: Dongdong Liu <liudongdong3@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
2015-12-04PCI: altera: Fix error when INTx is 4Ley Foon Tan
PCI interrupt lines start at 1, not at 0. So, creates additional one interrupt when register for irq domain. Error when PCIe devices have 4 INTx: WARNING: CPU: 1 PID: 1 at kernel/irq/irqdomain.c:280 irq_domain_associate+0x17c/0x1cc() error: hwirq 0x4 is too large for dummy Tested on Ethernet adapter card with multi-functions. Signed-off-by: Ley Foon Tan <lftan@altera.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-12-04PCI: altera: Check TLP completion statusLey Foon Tan
Check TLP packet successful completion status. This fix the issue when accessing multi-function devices in enumeration process, TLP will return error when accessing non-exist function number. Returns PCI error code instead of generic errno. Tested on Ethernet adapter card with multi-functions. [bhelgaas: simplify completion status checking code] Signed-off-by: Ley Foon Tan <lftan@altera.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-12-04PCI: altera: Fix Requester ID for config accessesLey Foon Tan
The Requester ID should use the Root Port devfn and it should be always 0. Previously we constructed the Requester ID using the *Completer* devfn, i.e., the devfn of the Function we expect to respond to the config access. This causes issues when accessing configuration space for devices other than the Root Port. Build the Requester ID using the Root Port devfn. Tested on Ethernet adapter card with multi-functions. Signed-off-by: Ley Foon Tan <lftan@altera.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-12-04PCI: altera: Fix loop in tlp_read_packet()Dan Carpenter
TLP_LOOP is 500 and the "loop" variable was a u8 so "loop < TLP_LOOP" is always true. We only need this condition to work if there is a problem so it would have been easy to miss this in testing. Make it a normal for loop with "int i" instead of over thinking things and making it complicated. Fixes: 6bb4dd154ae8 ("PCI: altera: Add Altera PCIe host controller driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Ley Foon Tan <lftan@altera.com>
2015-12-04PCI/MSI: Only use the generic MSI layer when domain is hierarchicalMarc Zyngier
Since d8a1cb757550 ("PCI/MSI: Let pci_msi_get_domain use struct device::msi_domain"), we use the MSI domain associated with the PCI device. But finding an MSI domain doesn't mean that the domain is implemented using the generic MSI domain API, and a number of MSI controllers are still using arch_setup_msi_irq() and arch_teardown_msi_irqs(). Check that the domain we just obtained is hierarchical. If it is, we can use the new generic MSI stuff. Otherwise we have to fall back to the old arch_setup_msi_irq() and arch_teardown_msi_irqs() interfaces. This avoids an oops in msi_domain_alloc_irqs() on systems with R-Car, Tegra, Armada 370, and probably other DesignWare-based host controllers. Fixes: d8a1cb757550 ("PCI/MSI: Let pci_msi_get_domain use struct device::msi_domain") Reported-by: Phil Edworthy <phil.edworthy@renesas.com> Tested-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> CC: stable@vger.kernel.org # v4.3+
2015-12-02PCI / PM: Tune down retryable runtime suspend error messagesImre Deak
The runtime PM core doesn't treat EBUSY and EAGAIN retvals from the driver suspend hooks as errors, but they still show up as errors in dmesg. Tune them down. See rpm_suspend() for details of handling these return values. Note that we use dev_dbg() for the retryable retvals, so after this change you'll need either CONFIG_DYNAMIC_DEBUG or CONFIG_PCI_DEBUG for them to show up in the log. One problem caused by this was noticed by Daniel: the i915 driver returns EAGAIN to signal a temporary failure to suspend and as a request towards the RPM core for scheduling a suspend again. This is a normal event, but the resulting error message flags a breakage during the driver's automated testing which parses dmesg and picks up the error. Reported-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://bugs.freedesktop.org/show_bug.cgi?id=92992 Signed-off-by: Imre Deak <imre.deak@intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-25ARM/PCI: Move align_resource function pointer to pci_host_bridge structureGabriele Paoloni
Commit b3a72384fe29 ("ARM/PCI: Replace pci_sys_data->align_resource with global function pointer") introduced an ARM-specific align_resource() function pointer. This is not portable to other arches and doesn't work for platforms with two different PCIe host bridge controllers. Move the function pointer to the pci_host_bridge structure so each host bridge driver can specify its own align_resource() function. Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2015-11-24PCI: hisi: Fix deferred probingArnd Bergmann
The hisi_pcie_probe() function is incorrectly marked as __init, as Kconfig tells us: WARNING: drivers/pci/host/built-in.o(.data+0x7780): Section mismatch in reference from the variable hisi_pcie_driver to the function .init.text:hisi_pcie_probe() If the probe for this device gets deferred past the point where __init functions are removed, or the device is unbound and then reattached to the driver, we branch into uninitialized memory, which is bad. Remove the __init annotation from hisi_pcie_probe() and hisi_add_pcie_port(). Fixes: 500a1d9a43e0 ("PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org> Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
2015-11-24PCI: designware: Remove incorrect io_base assignmentStanimir Varbanov
"pp->io" is an I/O resource, e.g., "[io 0x0000-0xffff]"; "pp->io_base" is the CPU physical address of a region where the host bridge converts CPU memory accesses into PCI I/O transactions. Corrupting pp->io_base by assigning pp->io->start to it breaks access to the PCI I/O space, as reported by Kishon. Remove the invalid assignment. [bhelgaas: changelog] Fixes: 0021d22b73d6 ("PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT") Reported-and-tested-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2015-11-24PCI: Prevent out of bounds access in numa_node overrideMathias Krause
Commit 1266963170f5 ("PCI: Prevent out of bounds access in numa_node override") missed that the user-provided node could also be negative. Handle this case as well to avoid out-of-bounds accesses to the node_states[] array. However, allow the special value -1, i.e. NUMA_NO_NODE, to be able to set the 'no specific node' configuration. Fixes: 1266963170f5 ("PCI: Prevent out of bounds access in numa_node override") Fixes: 63692df103e9 ("PCI: Allow numa_node override via sysfs") Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Sasha Levin <sasha.levin@oracle.com> CC: Prarit Bhargava <prarit@redhat.com> CC: stable@vger.kernel.org # v3.19+
2015-11-20Merge branches 'acpi-smbus', 'acpi-ec' and 'acpi-pci'Rafael J. Wysocki
* acpi-smbus: Revert "ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook" ACPI / SMBus: Fix boot stalls / high CPU caused by reentrant code * acpi-ec: ACPI-EC: Drop unnecessary check made before calling acpi_ec_delete_query() * acpi-pci: PCI: Fix OF logic in pci_dma_configure()
2015-11-20PCI: Fix OF logic in pci_dma_configure()Suravee Suthikulpanit
This patch fixes a bug introduced by previous commit, which incorrectly checkes the of_node of the end-point device. Instead, it should check the of_node of the host bridge. Fixes: 50230713b639 ("PCI: OF: Move of_pci_dma_configure() to pci_dma_configure()") Reported-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12Merge tag 'pm+acpi-4.4-rc1-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more power management and ACPI updates from Rafael Wysocki: "The only new feature in this batch is support for the ACPI _CCA device configuration object, which it a pre-requisite for future ACPI PCI support on ARM64, but should not affect the other architectures. The rest is fixes and cleanups, mostly in cpufreq (including intel_pstate), the Operating Performace Points (OPP) framework and tools (cpupower and turbostat). Specifics: - Support for the ACPI _CCA configuration object intended to tell the OS whether or not a bus master device supports hardware managed cache coherency and a new set of functions to allow drivers to check the cache coherency support for devices in a platform firmware interface agnostic way (Suravee Suthikulpanit, Jeremy Linton). - ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X (Aaron Lu, Hans de Goede). - Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers (Jon Medhurst, Nicolas Pitre). - kfree()-related fixup for the recently introduced CPPC cpufreq frontend (Markus Elfring). - intel_pstate fix reducing kernel log noise on systems where P-states are managed by hardware (Prarit Bhargava). - intel_pstate maintainers information update (Srinivas Pandruvada). - cpufreq core optimization related to the handling of delayed work items used by governors (Viresh Kumar). - Locking fixes and cleanups of the Operating Performance Points (OPP) framework (Viresh Kumar). - Generic power domains framework cleanups (Lina Iyer). - cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan, Thomas Renninger). - turbostat tool updates (Len Brown)" * tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits) PCI: ACPI: Add support for PCI device DMA coherency PCI: OF: Move of_pci_dma_configure() to pci_dma_configure() of/pci: Fix pci_get_host_bridge_device leak device property: ACPI: Remove unused DMA APIs device property: ACPI: Make use of the new DMA Attribute APIs device property: Adding DMA Attribute APIs for Generic Devices ACPI: Adding DMA Attribute APIs for ACPI Device device property: Introducing enum dev_dma_attr ACPI: Honor ACPI _CCA attribute setting cpufreq: CPPC: Delete an unnecessary check before the function call kfree() PM / OPP: Add opp_rcu_lockdep_assert() to _find_device_opp() PM / OPP: Hold dev_opp_list_lock for writers PM / OPP: Protect updates to list_dev with mutex PM / OPP: Propagate error properly from dev_pm_opp_set_sharing_cpus() cpufreq: s5pv210-cpufreq: fix wrong do_div() usage MAINTAINERS: update for intel P-state driver Creating a common structure initialization pattern for struct option cpupower: Enable disabled Cstates if they are below max latency cpupower: Remove debug message when using cpupower idle-set -D switch cpupower: cpupower monitor reports uninitialized values for offline cpus ...
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-17 05:49:41 +0000