| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This is the 5.4.193 stable release
Conflicts:
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
drivers/edac/synopsys_edac.c
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/mmc/host/sdhci.c
drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
sound/soc/codecs/msm8916-wcd-analog.c
|
|
[ Upstream commit 5ac121b81b4051e7fc83d5b3456a5e499d5bd147 ]
The AXP288's recommended and factory default Vhold value (minimum
input voltage below which the input current draw will be reduced)
is 4.4V. This lines up with other charger IC's such as the TI
bq2419x/bq2429x series which use 4.36V or 4.44V.
For some reason some BIOS-es initialize Vhold to 4.6V or even 4.7V
which combined with the typical voltage drop over typically low
wire gauge micro-USB cables leads to the input-current getting
capped below 1A (with a 2A capable dedicated charger) based on Vhold.
This leads to slow charging, or even to the device slowly discharging
if the device is in heavy use.
As the Linux AXP288 drivers use the builtin BC1.2 charger detection
and send the input-current-limit according to the detected charger
there really is no reason not to use the recommended 4.4V Vhold.
Set Vhold to 4.4V to fix the slow charging issue on various devices.
There is one exception, the special-case of the HP X2 2-in-1s which
combine this BC1.2 capable PMIC with a Type-C port and a 5V/3A factory
provided charger with a Type-C plug which does not do BC1.2. These
have their input-current-limit hardcoded to 3A (like under Windows)
and use a higher Vhold on purpose to limit the current when used
with other chargers. To avoid touching Vhold on these HP X2 laptops
the code setting Vhold is added to an else branch of the if checking
for these models.
Note this also fixes the sofar unused VBUS_ISPOUT_VHOLD_SET_MASK
define, which was wrong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d4f408cdcd26921c1268cb8dcbe8ffb6faf837f3 ]
As stated in [1], negative current values are used for discharging
batteries.
AXP PMICs internally have two different ADC channels for shunt current
measurement: one used during charging and one during discharging.
The values reported by these ADCs are unsigned.
While the driver properly selects ADC channel to get the data from,
it doesn't apply negative sign when reporting discharging current.
[1] Documentation/ABI/testing/sysfs-class-power
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6dee930f6f6776d1e5a7edf542c6863b47d9f078 ]
In free_charger_irq(), there is no free for 'WM8350_IRQ_CHG_FAST_RDY'.
Therefore, it should be better to add it in order to avoid the memory leak.
Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0b14b5ba11bec56fad344a4a0b2e16449cc8b94 ]
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid same code.
Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f7731754fdce33dad19be746f647d6ac47c5d695 ]
The datasheet says that the BQ24190_REG_POC_CHG_CONFIG bits can
have a value of either 10(0x2) or 11(0x3) for OTG (5V boost regulator)
mode.
Sofar bq24190_vbus_is_enabled() was only checking for 10 but some BIOS-es
uses 11 when enabling the regulator at boot.
Make bq24190_vbus_is_enabled() also check for 11 so that it does not
wrongly returns false when the bits are set to 11.
Fixes: 66b6bef2c4e0 ("power: supply: bq24190_charger: Export 5V boost converter as regulator")
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6a4760463dbc6b603690938c468839985189ce0a ]
kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Fix memory leak by calling kobject_put().
Fixes: 8c0984e5a753 ("power: move power supply drivers to power/supply")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba18dad0fb880cd29aa97b6b75560ef14d1061ba ]
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: f7a388d6cd1c ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 80211be1b9dec04cc2805d3d81e2091ecac289a1 ]
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
toradex_5.4-2.3.x-imx-v5.4.161
Conflicts:
drivers/net/phy/micrel.c
drivers/usb/chipidea/core.c
|
|
commit 644106cdb89844be2496b21175b7c0c2e0fab381 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
Fixes: 6647156c00cc ("power: reset: add LTC2952 poweroff driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: https://github.com/llvm/llvm-project/commit/a8083d42b1c346e21623a1d36d1f0cadd7801d83
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 51c7b6a0398f54b9120795796a4cff4fc9634f7d upstream.
We should not go on looking for more capacity tables after
we realize we have looked at the last one in
power_supply_find_ocv2cap_table().
Fixes: 3afb50d7125b ("power: supply: core: Add some helpers to use the battery OCV capacity table")
Cc: Chunyan Zhang <chunyan.zhang@unisoc.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.4.160 stable release
|
|
[ Upstream commit cdf10ffe8f626d8a2edc354abf063df0078b2d71 ]
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c09795 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf895295e9a73411889816f1a0c1f4f1a2d9c678 ]
Currently the rt5033_battery driver provides voltage values in mV. It
should be µV as stated in Documentation/power/power_supply_class.rst.
Fixes: b847dd96e659 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 223a3b82834f036a62aa831f67cbf1f1d644c6e2 upstream.
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b154 ("power_supply: Add MAX17042 Fuel Gauge Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e660dbb68c6b3f7b9eb8b9775846a44f9798b719 upstream.
max17042_set_soc_threshold gets called with offset set to 1, which means
that minimum threshold value would underflow once SOC got down to 0,
causing invalid alerts from the gauge.
Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
This is the 5.4.148 stable release
Conflicts:
- drivers/dma/imx-sdma.c:
Following upstream patches are already applied to NXP tree:
7cfbf391e870 ("dmaengine: imx-sdma: remove duplicated sdma_load_context")
788122c99d85 ("Revert "dmaengine: imx-sdma: refine to load context only
once"")
- drivers/usb/chipidea/host.c:
Merge upstream commit a18cfd715e91 ("usb: chipidea: host: fix port index
underflow and UBSAN complains") to NXP version.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
commit 54784ffa5b267f57161eb8fbb811499f22a0a0bf upstream.
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc4f ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.4.147 stable release
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
[ Upstream commit ed0d0a0506025f06061325cedae1bbebd081620a ]
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
errors
[ Upstream commit caa534c3ba40c6e8352b42cbbbca9ba481814ac8 ]
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 5.4.134 stable release
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
[ Upstream commit f3076cd8d1d5fa64b5e1fa5affc045c2fc123baa ]
The fuel gauge in the RT5033 PMIC has its own I2C bus and interrupt
line. Therefore, it is not actually part of the RT5033 MFD and needs
its own of_match_table to probe properly.
Also, given that it's independent of the MFD, there is actually
no need to make the Kconfig depend on MFD_RT5033. Although the driver
uses the shared <linux/mfd/rt5033.h> header, there is no compile
or runtime dependency on the RT5033 MFD driver.
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Fixes: b847dd96e659 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dfe52db13ab8d24857a9840ec7ca75eef800c26c ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 073b5d5b1f9cc94a3eea25279fbafee3f4f5f097 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed3443fb4df4e140a22f65144546c8a8e1e27f4e ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7fbf6b731bca347700e460d94b130f9d734b33e9 ]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 17047/77693 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5bcb5087c9dd3dca1ff0ebd8002c5313c9332b56 ]
Sometimes the code will crash because we haven't enabled
AC or USB charging and thus not created the corresponding
psy device. Fix it by checking that it is there before
notifying.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2aac79d14d76879c8e307820b31876e315b1b242 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 603fcfb9d4ec1cad8d66d3bb37f3613afa8a661a ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
s3c_adc_bat_remove()
[ Upstream commit 68ae256945d2abe9036a7b68af4cc65aff79d5b7 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6cfa007b3b229771d9588970adb4ab3e0487f49 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2469b836fa835c67648acad17d62bc805236a6ea ]
Fixes coccicheck error:
drivers/power/supply/pm2301_charger.c:1089:7-27: ERROR:
drivers/power/supply/lp8788-charger.c:502:8-28: ERROR:
drivers/power/supply/tps65217_charger.c:239:8-33: ERROR:
drivers/power/supply/tps65090-charger.c:303:8-33: ERROR:
Threaded IRQ with no primary handler requested without IRQF_ONESHOT
Signed-off-by: dongjian <dongjian@yulong.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c4d57c22ac65bd503716062a06fad55a01569cac ]
On all newer bq27xxx ICs, the AveragePower register contains a signed
value; in addition to handling the raw value as unsigned, the driver
code also didn't convert it to µW as expected.
At least for the BQ28Z610, the reference manual incorrectly states that
the value is in units of 1mW and not 10mW. I have no way of knowing
whether the manuals of other supported ICs contain the same error, or if
there are models that actually use 1mW. At least, the new code shouldn't
be *less* correct than the old version for any device.
power_avg is removed from the cache structure, se we don't have to
extend it to store both a signed value and an error code. Always getting
an up-to-date value may be desirable anyways, as it avoids inconsistent
current and power readings when switching between charging and
discharging.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 5.4.118 stable release
Conflicts (manual resolve):
- drivers/mmc/core/core.c:
- drivers/mmc/core/host.c:
Fix merge fuzz for upstream commit 909a01b95120 ("mmc: core: Fix hanging
on I/O during system suspend for removable cards")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
s3c_adc_bat_remove()
[ Upstream commit 68ae256945d2abe9036a7b68af4cc65aff79d5b7 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6cfa007b3b229771d9588970adb4ab3e0487f49 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2469b836fa835c67648acad17d62bc805236a6ea ]
Fixes coccicheck error:
drivers/power/supply/pm2301_charger.c:1089:7-27: ERROR:
drivers/power/supply/lp8788-charger.c:502:8-28: ERROR:
drivers/power/supply/tps65217_charger.c:239:8-33: ERROR:
drivers/power/supply/tps65090-charger.c:303:8-33: ERROR:
Threaded IRQ with no primary handler requested without IRQF_ONESHOT
Signed-off-by: dongjian <dongjian@yulong.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c4d57c22ac65bd503716062a06fad55a01569cac ]
On all newer bq27xxx ICs, the AveragePower register contains a signed
value; in addition to handling the raw value as unsigned, the driver
code also didn't convert it to µW as expected.
At least for the BQ28Z610, the reference manual incorrectly states that
the value is in units of 1mW and not 10mW. I have no way of knowing
whether the manuals of other supported ICs contain the same error, or if
there are models that actually use 1mW. At least, the new code shouldn't
be *less* correct than the old version for any device.
power_avg is removed from the cache structure, se we don't have to
extend it to store both a signed value and an error code. Always getting
an up-to-date value may be desirable anyways, as it avoids inconsistent
current and power readings when switching between charging and
discharging.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
toradex_5.4-2.3.x-imx
This basically contains NXP BSP Patch L5.4.70_2.3.2 plus kernel.org
v5.4.115 from https://github.com/Freescale/linux-fslc/tree/5.4-2.3.x-imx.
Related-to: ELB-3958
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
This is the 5.4.102 stable release
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
[ Upstream commit 95aa21a3f1183260db1b0395e03df5bebc5ed641 ]
According to datasheet WKUPDBC mask is b/w bits 26..24.
Fixes: f80cb48843987 ("power: reset: at91-shdwc: add new shutdown controller driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Property "force-mode" tells the driver to replace previously
initialized power-off kernel hook and allows gpio-poweroff to
probe and operate successfully in any case.
Related-to: #42589
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
(cherry picked from commit 371447a8663984d8ff090288247805cea3dc4282)
Conflicts:
Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt
drivers/power/reset/gpio-poweroff.c
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
This is the 5.4.87 stable release
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
This is the 5.4.75 stable release
Conflicts:
- drivers/i2c/busses/i2c-imx.c:
Drop NXP changes, which are covered by commit [2c58d5e0c754c] from
upstream.
- drivers/net/can/flexcan.c:
Keep NXP implementation, patch [ca10989632d88] from upstream is
covered in the NXP tree.
- drivers/usb/host/xhci.h:
Fix merge fuzz for upstream commit [2600a131e1f61].
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
|
|
[ Upstream commit b2f6cb78eaa1cad57dd3fe11d0458cd4fae9a584 ]
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in callers(bq24190_sysfs_show,
bq24190_charger_get_property, bq24190_charger_set_property,
bq24190_battery_get_property, bq24190_battery_set_property),
so we should fix it.
Fixes: f385e6e2a1532 ("power: bq24190_charger: Use PM runtime autosuspend")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a0f1ccd96c7049377d892a4299b6d5e47ec9179d ]
Commit 9c80662a74cd ("power: supply: axp288_charger: Add special handling
for HP Pavilion x2 10") added special handling for HP Pavilion x2 10
models which use the weird combination of a Type-C connector and the
non Type-C aware AXP288 PMIC.
This special handling was activated by a DMI match a the product-name
of "HP Pavilion x2 Detachable". Recently I've learned that there are
also older "HP Pavilion x2 Detachable" models with an AXP288 PMIC +
a micro-usb connector where we should not activate the special handling
for the Type-C connectors.
Extend the matching to also match on the DMI board-name and match on the
2 boards (one Bay Trail based one Cherry Trail based) of which we are
certain that they use the AXP288 + Type-C connector combination.
Note the DSDT code from these older (AXP288 + micro-USB) models contains
some AML code (which never runs under Linux) which reads the micro-USB
connector id-pin and if it is pulled to ground, which would normally mean
the port is in host mode!, then it sets the input-current-limit to 3A,
it seems HP is using the micro-USB port as a charging only connector
and identifies their own 3A capable charger though this hack which is a
major violation of the USB specs. Note HP also hardcodes a 2A limit
when the id-pin is not pulled to ground, which is also in violation
of the specs.
I've no intention to add support for HP's hack to support 3A charging
on these older models. By making the DMI matches for the Type-C equipped
models workaround more tighter, these older models will be treated just
like any other AXP288 + micro-USB equipped device and the input-current
limit will follow the BC 1.2 spec (using the defacto standard values
there where the BC 1.2 spec defines a range).
Fixes: 9c80662a74cd ("power: supply: axp288_charger: Add special handling for HP Pavilion x2 10")
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1896924
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
