| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This patch adds missing registers('BUCK7_SW' & 'LDO29_CTRL'). Since BUCK7 has
1 more register (BUCK7_SW) than others, register offset should
be added one more for which has bigger address than BUCK7 registers.
Fixes: 76b9840b24ae04(regulator: s2mps11: Add support S2MPS13 regulator device)
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull one regulator fix from Mark Brown:
"One fix here, a fix for the voltage mapping on one of the s2mps11
regulators which broke systems using it including apparently the
Gear 2 smartwatches"
* tag 'regulator-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: Fix dw_mmc failure on Gear 2
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
Invalid buck4 configuration for linear mapping of voltage in S2MPS14
regulators caused boot failure on Gear 2 (dw_mmc-exynos):
[ 3.569137] EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: (null)
[ 3.571716] VFS: Mounted root (ext4 filesystem) readonly on device 179:15.
[ 3.629842] mmcblk0: error -110 sending status command, retrying
[ 3.630244] mmcblk0: error -110 sending status command, retrying
[ 3.636292] mmcblk0: error -110 sending status command, aborting
Buck4 voltage regulator has different minimal voltage value than other
bucks. Commit merging multiple regulator description macros caused to
use linear_min_sel from buck[1235] regulators as value for buck4. This
lead to lower voltage of buck4 than required.
Output of the buck4 is used internally as power source for
LDO{3,4,7,11,19,20,21,23}. On Gear 2 board LDO11 is used as MMC
regulator (V_EMMC_1.8V).
Fixes: 5a867cf28893 ("regulator: s2mps11: Optimize the regulator description macro")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The main thing this time around is support for suspend mode
configuration from DT which will enable some very useful power savings
on systems where we can't rely on the bootloader configuration. We
still don't really support dynamic configuration of this at runtime,
that may come later if there is any demand.
Summary:
- Support for specifying the target regulation mode and voltage
during system suspend via DT, enabling power savings in that mode.
- Reduce the default verbosity of the logging on boot, improving boot
times especially for systems with very large numbers of regulators.
- Lots of cleanups and fixes for Maxim PMIC drivers.
- New driver for Richtek RT5033"
* tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (62 commits)
regulator: core: Fix regualtor_ena_gpio_free not to access pin after freeing
regulator: sky81452: Modify Device Tree structure
regulator: sky81452: Modify Device Tree structure
dt-bindings: Update documentation for "system-power-controller" and fix misspellings
of: Rename "poweroff-source" property to "system-power-controller"
regulator: max77686: Remove support for board files
regulator: max77802: Remove support for board files
regulator: max77802: Fill regulator modes translation callback
regulator: max77802: Document binding for regulator operating modes
regulator: of: Add support for parsing initial and suspend modes
regulator: of: Pass the regulator description in the match table
regulator: of: Add regulator desc param to of_get_regulator_init_data()
regulator: Add mode mapping function to struct regulator_desc
regulator: Document binding for initial and suspend modes
regulator: core: Add PRE_DISABLE notification
regulator: gpio: fix parsing of gpio list
regulator: rpm: add support for RPM-controller SMB208
regulator: da9063: Do not transform local IRQ to virtual
regulator: sky81452: Modify dependent Kconfig symbol
regulator: rt5033: Add RT5033 Regulator device driver
...
|
|
'regulator/topic/rpm', 'regulator/topic/rt5033', 'regulator/topic/s2mpa01' and 'regulator/topic/s2mps11' into regulator-next
|
|
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch sets ena_gpio_initialized for all drivers which set a
ena_gpio from parsed DT properties. Drivers using pdata may get zero
initialized pdata and therefore copy a 0 into the regulator_config
ena_gpio field.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The driver was allocating memory for storing GPIOs for external control
with unnecessary GFP_ZERO flag. Then right after allocation it
initialized memory to -EINVAL in loop. Skip the GFP_ZERO flag.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch makes the regulator description macro take minimum and
steps voltage as parameter. In this way many repeated macros can be
removed. Now these macros are repeated only if the the LDO/BUCK ctrl
registers have non-linear positions. The good thing is these ctrl registers
are mostly linear so they are not passed as parameters.
This patch reduces the code size and also allow easy addition of more
s2mpxxx PMIC drivers which differs a lot in minimum/step voltages.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This is a cleanup patch and moves min/step voltages in a common samsung
header file so that they can be used by other s2mpxxx PMIC drivers. Only
few required macros are added currently and others can be added if needed.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
|
|
This driver also supports S2MPU02 now, thus update module description and
Kconfig accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch add S2MPU02 regulator device to existing S2MPS11 device driver
because of little difference between S2MPS1x and S2MPU02. The S2MPU02
regulator device includes LDO[1-28] and BUCK[1-7].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[Add missing linear_min_sel of S2MPU02 LDO regulators by Jonghwa Lee]
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
S2MPS11 supports enabling/disabling ramp delay only for buck[2346].
Other bucks have ramp delay enabled always.
However the bit shift for enabling buck6 ramp delay in register is equal
to 0. When ramp delay was set for the bucks unsupporting enable/disable
(buck[15789] and buck10), the ramp delay for buck6 was also enabled.
Fixes: b96244fad953 ("regulator: s2mps11: Don't check enable_shift before setting enable ramp rate")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
GPIO 0 is a valid GPIO so allow using it as external control for
S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add support for external control over GPIO for LDO10, LDO11 and LDO12
S2MPS14 regulators. External control can be turned on by writing 0x0 to
control register which in case of other regulators is used for disabling
them. These LDO10-LDO12 regulators can be disabled only by I2C GPIO or
PWREN pin so the patch actually allows proper way of disabling them.
Additionally the GPIO control has two benefits:
- It is faster than toggling it over I2C bus.
- It allows disabling the regulator during suspend to RAM; The AP will
enable it during resume.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Refactor code for parsing DTS to increase a little code readability. The
behaviour should not change.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current code misses updating the register when enable_shift is 0.
e.g. S2MPS11_BUCK9_RAMP_SHIFT and S2MPS11_BUCK6_RAMP_EN_SHIFT are 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'regulator/topic/max8997', 'regulator/topic/max8998', 'regulator/topic/mc13xxx', 'regulator/topic/pfuze100', 'regulator/topic/rc5t583' and 'regulator/topic/s2mps11' into regulator-next
|
|
|
|
Add of_node_put to decrement the ref count.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
S2MPS14 regulators support suspend mode where their status is controlled
by PWREN coming from SoC. This patch implements the set_suspend_disable
for S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add support for S2MPS14 PMIC regulators to s2mps11 driver. The S2MPS14
has fewer BUCK-s and LDO-s than S2MPS11. It also does not support
controlling the BUCK ramp delay.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Remove __initconst from regulator_desc array because this array is used
during probe and s2mps11_pmic_probe() is not in __init section. However
still select the number of supported regulators according to device ID
so the driver will be ready for adding support for S2MPS14 device.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add __initconst to 'regulator_desc' array with supported regulators.
During probe choose how many and which regulators will be supported
according to device ID. Then copy the 'regulator_desc' array to
allocated memory so the regulator core can use it.
Additionally allocate array of of_regulator_match() dynamically (based
on number of regulators) instead of allocation on the stack.
This is needed for supporting different devices in s2mps11
driver and actually prepares the regulator driver for supporting the
S2MPS14 device.
Code for supporting the S2MPS14 device will add its own array of
'regulator_desc' (also marked as __initconst). This way memory footprint
of the driver will be reduced (approximately 'regulators_desc' array for
S2MPS11 occupies 5 kB on 32-bit ARM, for S2MPS14 will occupy 3 kB).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Yadwinder Singh Brar <yadi.brar01@gmail.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Constify the regulator_desc 'regulators' array.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Regulators registered by devm_regulator_register() do not have to be
stored in state container because they are never dereferenced later.
The array of regulator_dev can be safely removed from state container.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Thiago Farina <tfarina@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
When platform_data is used for regulator (of_node of sec-core MFD device
is NULL) the config.of_node for regulator is not initialized. This NULL
value of config.of_node is later stored during regulator_register().
Thus any call by regulator consumers to of_get_regulator() will fail on
of_parse_phandle() returning NULL.
In this case (using platform_data and parent's driver of_node is NULL)
set the config.of_node to reg_node from platform_data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'regulator/topic/s5m8767', 'regulator/topic/stw481x-vmmc', 'regulator/topic/tps51632', 'regulator/topic/tps62360', 'regulator/topic/tps65910', 'regulator/topic/twl' and 'regulator/topic/wm831x' into regulator-linus
|
|
BUCK 3 and 4 share the same ramp delay. Hence make it a fall through
case instead of duplicating the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Fix building of s2mps11 regulator and clock drivers after renaming
regmap field in struct sec_pmic_dev in commit:
- "mfd/rtc: s5m: Fix register updating by adding regmap for RTC"
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit e398b51a ("regulator: s2mps11: Convert to devm_regulator_register()")
intended to do this conversion. However the actual conversion to devm_* got
missed out. Fix this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
|
|
Current code has wrong mask and val arguments for updating ramp_delay. Fix it.
Also ensure the return value of get_ramp_delay() won't greater than 3 because
the mask field for ramp_val only takes 2 bits.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current code calls regmap_update_bits() with mask and val arguments swapped.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since now we have ramp_delay and ramp_disable as standard regulator
constraints and DT part using it so this patch removes legacy part i.e. getting
ramp_delayxx and ramp_enable from pdata since it can be passed as
standard regulator constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds DT support for parsing regulators constraints for parent(mfd)
node and moves some common intialising code out of loop while registering.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Implementing set_ramp_rate() and using standard constraints for getting
ramp_delay and ramp_disable, instead of getting it as s2mps11 specific data
through platform data, makes driver more compliant with framework and reduces
the complexity for adding DT support.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Currently driver uses local struct s2mps11_info to store ramp rate for bucks
whic its getting through platform data, so instead of using regulator
constraints it should use s2mps11_info to calculate ramp delay.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch makes driver to use uV/us as units of ramp_delay. It makes driver
in compliance with regulator framework and make ramp rate precise.
This patch also sets default ramp rate in regulator descriptor which can be
used in case if case ramp rate is not set in regulator constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
All the drivers that need delay for the regulator voltage output voltage to
stabilize after being enabled or after being set to a new value has been
converted to implement enable_time and set_voltage_time_sel callbacks.
Then regulator core will take care of the necessary delay.
This patch removes the unneeded include of linux/delay.h in regulator drivers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
For BUCK10 the control registers are wrongly set as buck9 control register
This patch corrects the control registers for buck10
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
|
|
This patch fix the abnormal ramp delay setting.
The shift operation was wrong.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
