summaryrefslogtreecommitdiff
path: root/drivers/s390/net/qeth_core_main.c
AgeCommit message (Collapse)Author
2018-08-09s390/qeth: reduce hard-coded access to ccw channelsJulian Wiedmann
Where possible use accessor macros and local pointers to access the ccw channels. This makes it less likely to miss a spot. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-09s390/qeth: extract helper for MPC protocol typeJulian Wiedmann
Just a little code deduplication. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: speed up L2 IQD xmitJulian Wiedmann
Modify the L2 OSA xmit path so that it also supports L2 IQD devices (in particular, their HW header requirements). This allows IQD devices to advertise NETIF_F_SG support, and eliminates the allocation overhead for the HW header. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: add support for constrained HW headersJulian Wiedmann
Some transmit modes require that the HW header is located in the same page as the initial protocol headers in skb->data. Let callers specify the size of this contiguous header range, and enforce it when building the HW header. While at it, apply some gentle renaming to the relevant L2 code so that it matches the L3 code. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: merge linearize-check into HW header constructionJulian Wiedmann
When checking whether an skb needs to be linearized to fit into an IO buffer, it's desirable to consider the skb's final size and layout (ie. after the HW header was added). But a subsequent linearization can then cause the re-positioned HW header to violate its alignment restrictions. Dealing with this situation in two different code paths is quite tricky. This patch integrates a) linearize-check and b) HW header construction into one 3 step-sequence: 1. evaluate how the HW header needs to be added (to identify if it takes up an additional buffer element), then 2. check if the required buffer elements exceed the device's limit. Linearize when necessary and re-evaluate the HW header placement. 3. Add the HW header in the best-possible way: a) push, without taking up an additional buffer element b) push, but consume another buffer element c) allocate a header object from the cache. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: add statistics for consumed buffer elementsJulian Wiedmann
Nowadays an skb fragment typically spans over multiple pages. So replace the obsolete, SG-only 'fragments' counter with one that tracks the consumed buffer elements. This is what actually matters for performance. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: use core MTU range checkingJulian Wiedmann
qeth's ndo_change_mtu() only applies some trivial bounds checking. Set up dev->min_mtu properly, so that dev_set_mtu() can do this for us. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: simplify max MTU handlingJulian Wiedmann
When the MPC initialization code discovers the HW-specific max MTU, apply the resulting changes straight to the netdevice. If this is the device's first initialization, also set its MTU (HiperSockets: the max MTU; else: a layer-specific default value). Then cap the current MTU by the new max MTU. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: don't cache HW port numberJulian Wiedmann
The netdevice is always available now, so get the portno from there. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: allocate netdevice earlyJulian Wiedmann
Allocation of the netdevice is currently delayed until a qeth card first goes online. This complicates matters in several places, where we need to cache values instead of applying them straight to the netdevice. Improve on this by moving the allocation up to where the qeth card itself is created. This is also one step in direction of eventually placing the qeth card into netdev_priv(). In all subsequent code, remove the now redundant checks whether card->dev is valid. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: remove redundant netif_carrier_ok() checksJulian Wiedmann
netif_carrier_off() does its own checking. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-21s390/qeth: fix race in used-buffer accountingJulian Wiedmann
By updating q->used_buffers only _after_ do_QDIO() has completed, there is a potential race against the buffer's TX completion. In the unlikely case that the TX completion path wins, qeth_qdio_output_handler() would decrement the counter before qeth_flush_buffers() even incremented it. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-12s390/qeth: clean up exported symbolsJulian Wiedmann
Remove some redundant EXPORTs. While at it, also move some L2-only prototypes into the proper header file. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-12s390/qeth: consolidate ccwgroup driver definitionJulian Wiedmann
Reshuffle the code a bit so that everything is in one place. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-12s390/qeth: clean up Output Queue selectionJulian Wiedmann
Consolidate duplicated code, fix the misuse of RTN_UNSPEC and simplify the handling of non-unicast traffic on IQD devices. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-12s390/qeth: remove unused buffer->aob pointerJulian Wiedmann
Except for tracing, the pointer is not used. At the same time, accessing it from qeth_qdio_output_handler() is racy: whenever qeth_qdio_cq_handler() gets control, its call to qeth_qdio_handle_aob() frees the AOB. So the AOB pointer that qeth_qdio_output_handler() stores into 'buffer' can go stale at any time, and trigger a use-after-free. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-12s390/qeth: various buffer management cleanupsJulian Wiedmann
Use the new qeth_scrub_qdio_buffer() helper, remove an extra parameter from qeth_clear_output_buffer(), init the bufstates.user field just once (in qeth_flush_buffers()) and remove some noisy trace messages. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-30s390/qeth: consistently re-enable device featuresJulian Wiedmann
commit e830baa9c3f0 ("qeth: restore device features after recovery") and commit ce3443564145 ("s390/qeth: rely on kernel for feature recovery") made sure that the HW functions for device features get re-programmed after recovery. But we missed that the same handling is also required when a card is first set offline (destroying all HW context), and then online again. Fix this by moving the re-enable action out of the recovery-only path. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-30s390/qeth: don't clobber buffer on async TX completionJulian Wiedmann
If qeth_qdio_output_handler() detects that a transmit requires async completion, it replaces the pending buffer's metadata object (qeth_qdio_out_buffer) so that this queue buffer can be re-used while the data is pending completion. Later when the CQ indicates async completion of such a metadata object, qeth_qdio_cq_handler() tries to free any data associated with this object (since HW has now completed the transfer). By calling qeth_clear_output_buffer(), it erronously operates on the queue buffer that _previously_ belonged to this transfer ... but which has been potentially re-used several times by now. This results in double-free's of the buffer's data, and failing transmits as the buffer descriptor is scrubbed in mid-air. The correct way of handling this situation is to 1. scrub the queue buffer when it is prepared for re-use, and 2. later obtain the data addresses from the async-completion notifier (ie. the AOB), instead of the queue buffer. All this only affects qeth devices used for af_iucv HiperTransport. Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-30Revert "s390/qeth: use Read device to query hypervisor for MAC"Julian Wiedmann
This reverts commit b7493e91c11a757cf0f8ab26989642ee4bb2c642. On its own, querying RDEV for a MAC address works fine. But when upgrading from a qeth that previously queried DDEV on a z/VM NIC (ie. any kernel with commit ec61bd2fd2a2), the RDEV query now returns a _different_ MAC address than the DDEV query. If the NIC is configured with MACPROTECT, z/VM apparently requires us to use the MAC that was initially returned (on DDEV) and registered. So after upgrading to a kernel that uses RDEV, the SETVMAC registration cmd for the new MAC address fails and we end up with a non-operabel interface. To avoid regressions on upgrade, switch back to using DDEV for the MAC address query. The downgrade path (first RDEV, later DDEV) is fine, in this case both queries return the same MAC address. Fixes: b7493e91c11a ("s390/qeth: use Read device to query hypervisor for MAC") Reported-by: Michal Kubecek <mkubecek@suse.com> Tested-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: 1) Add Maglev hashing scheduler to IPVS, from Inju Song. 2) Lots of new TC subsystem tests from Roman Mashak. 3) Add TCP zero copy receive and fix delayed acks and autotuning with SO_RCVLOWAT, from Eric Dumazet. 4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard Brouer. 5) Add ttl inherit support to vxlan, from Hangbin Liu. 6) Properly separate ipv6 routes into their logically independant components. fib6_info for the routing table, and fib6_nh for sets of nexthops, which thus can be shared. From David Ahern. 7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP messages from XDP programs. From Nikita V. Shirokov. 8) Lots of long overdue cleanups to the r8169 driver, from Heiner Kallweit. 9) Add BTF ("BPF Type Format"), from Martin KaFai Lau. 10) Add traffic condition monitoring to iwlwifi, from Luca Coelho. 11) Plumb extack down into fib_rules, from Roopa Prabhu. 12) Add Flower classifier offload support to igb, from Vinicius Costa Gomes. 13) Add UDP GSO support, from Willem de Bruijn. 14) Add documentation for eBPF helpers, from Quentin Monnet. 15) Add TLS tx offload to mlx5, from Ilya Lesokhin. 16) Allow applications to be given the number of bytes available to read on a socket via a control message returned from recvmsg(), from Soheil Hassas Yeganeh. 17) Add x86_32 eBPF JIT compiler, from Wang YanQing. 18) Add AF_XDP sockets, with zerocopy support infrastructure as well. From Björn Töpel. 19) Remove indirect load support from all of the BPF JITs and handle these operations in the verifier by translating them into native BPF instead. From Daniel Borkmann. 20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha. 21) Allow XDP programs to do lookups in the main kernel routing tables for forwarding. From David Ahern. 22) Allow drivers to store hardware state into an ELF section of kernel dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy. 23) Various RACK and loss detection improvements in TCP, from Yuchung Cheng. 24) Add TCP SACK compression, from Eric Dumazet. 25) Add User Mode Helper support and basic bpfilter infrastructure, from Alexei Starovoitov. 26) Support ports and protocol values in RTM_GETROUTE, from Roopa Prabhu. 27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard Brouer. 28) Add lots of forwarding selftests, from Petr Machata. 29) Add generic network device failover driver, from Sridhar Samudrala. * ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits) strparser: Add __strp_unpause and use it in ktls. rxrpc: Fix terminal retransmission connection ID to include the channel net: hns3: Optimize PF CMDQ interrupt switching process net: hns3: Fix for VF mailbox receiving unknown message net: hns3: Fix for VF mailbox cannot receiving PF response bnx2x: use the right constant Revert "net: sched: cls: Fix offloading when ingress dev is vxlan" net: dsa: b53: Fix for brcm tag issue in Cygnus SoC enic: fix UDP rss bits netdev-FAQ: clarify DaveM's position for stable backports rtnetlink: validate attributes in do_setlink() mlxsw: Add extack messages for port_{un, }split failures netdevsim: Add extack error message for devlink reload devlink: Add extack to reload and port_{un, }split operations net: metrics: add proper netlink validation ipmr: fix error path when ipmr_new_table fails ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds net: hns3: remove unused hclgevf_cfg_func_mta_filter netfilter: provide udp*_lib_lookup for nf_tproxy qed*: Utilize FW 8.37.2.0 ...
2018-05-02Merge branch 'timers/urgent' into timers/coreThomas Gleixner
Pick up urgent fixes to apply dependent cleanup patch
2018-04-27s390/qeth: add IPv6 RX checksum offload supportKittipon Meesompop
Check if a qeth device supports IPv6 RX checksum offload, and hook it up into the existing NETIF_F_RXCSUM support. As NETIF_F_RXCSUM is now backed by a combination of HW Assists, we need to be a little smarter when dealing with errors during a configuration change: - switching on NETIF_F_RXCSUM only makes sense if at least one HW Assist was enabled successfully. - for switching off NETIF_F_RXCSUM, all available HW Assists need to be deactivated. Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27s390/qeth: add IPv6 TX checksum offload supportKittipon Meesompop
Check if a qeth device supports IPv6 TX checksum offload, and advertise NETIF_F_IPV6_CSUM accordingly. Add support for setting the relevant bits in IPv6 packet descriptors. Currently this has only limited use (ie. UDP, or Jumbo Frames). For any TCP traffic with a standard MSS, the TCP checksum gets calculated as part of the linear GSO segmentation. Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27s390/qeth: extend Checksum Offload Assists for IPv6Kittipon Meesompop
Add some wrappers to make the protocol-specific Assist code a little more generic, and use them for sending protocol-agnostic commands in the Checksum Offload Assist code. Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27s390/qeth: query IPv6 assists during hardsetupKittipon Meesompop
For new functionality, the L2 subdriver will start using IPv6 assists. So move the query from the L3 subdriver into the common setup path. Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27s390/qeth: add stats counter for RX csum offloadKittipon Meesompop
This matches the statistics we gather for the TX offload path. Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27s390/qeth: convert vlan spinlock to mutexJulian Wiedmann
As the vid_list is only accessed from process context, there's no need to protect it with a spinlock. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27s390/qeth: skip QDIO queue handler indirectionJulian Wiedmann
Both qeth sub drivers use the same QDIO queue handlers, there's no need to expose them via the driver's discipline. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-22s390/qeth: use Read device to query hypervisor for MACJulian Wiedmann
For z/VM NICs, qeth needs to consider which of the three CCW devices in an MPC group it uses for requesting a managed MAC address. On the Base device, the hypervisor returns a default MAC which is pre-assigned when creating the NIC (this MAC is also returned by the READ MAC primitive). Querying any other device results in the allocation of an additional MAC address. For consistency with READ MAC and to avoid using up more addresses than necessary, it is preferable to use the NIC's default MAC. So switch the the diag26c over to using a NIC's Read device, which should always be identical to the Base device. Fixes: ec61bd2fd2a2 ("s390/qeth: use diag26c to get MAC address on L2") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-22s390/qeth: fix request-side race during cmd IO timeoutJulian Wiedmann
Submitting a cmd IO request (usually on the WRITE device, but for IDX also on the READ device) is currently done with ccw_device_start() and a manual timeout in the caller. On timeout, the caller cleans up the related resources (eg. IO buffer). But 1) the IO might still be active and utilize those resources, and 2) when the IO completes, qeth_irq() will attempt to clean up the same resources again. Instead of introducing additional resource locking, switch to ccw_device_start_timeout() to ensure IO termination after timeout, and let the IRQ handler alone deal with cleaning up after a request. This also removes a stray write->irq_pending reset from clear_ipacmd_list(). The routine doesn't terminate any pending IO on the WRITE device, so this should be handled properly via IO timeout in the IRQ handler. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-22s390/qeth: handle failure on workqueue creationJulian Wiedmann
Creating the global workqueue during driver init may fail, deal with it. Also, destroy the created workqueue on any subsequent error. Fixes: 0f54761d167f ("qeth: Support VEPA mode") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-22s390/qeth: avoid control IO completion stallsJulian Wiedmann
For control IO, qeth currently tracks the index of the buffer that it expects to complete the next IO on each qeth_channel. If the channel presents an IRQ while this buffer has not yet completed, no completion processing for _any_ completed buffer takes place. So if the 'next buffer' is skipped for any sort of reason* (eg. when it is released due to error conditions, before the IO is started), the buffer obviously won't switch to PROCESSED until it is eventually allocated for a _different_ IO and completes. Until this happens, all completion processing on that channel stalls and pending requests possibly time out. As a fix, remove the whole 'next buffer' logic and simply process any IO buffer right when it completes. A channel will never have more than one IO pending, so there's no risk of processing out-of-sequence. *Note: currently just one location in the code really handles this problem, by advancing the 'next' index manually. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-22s390/qeth: fix error handling in adapter command callbacksJulian Wiedmann
Make sure to check both return code fields before(!) processing the command response. Otherwise we risk operating on invalid data. This matches an earlier fix for SETASSPARMS commands, see commit ad3cbf613329 ("s390/qeth: fix error handling in checksum cmd callback"). Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19compat: Move compat_timespec/ timeval to compat_time.hDeepa Dinamani
All the current architecture specific defines for these are the same. Refactor these common defines to a common header file. The new common linux/compat_time.h is also useful as it will eventually be used to hold all the defines that are needed for compat time types that support non y2038 safe types. New architectures need not have to define these new types as they will only use new y2038 safe syscalls. This file can be deleted after y2038 when we stop supporting non y2038 safe syscalls. The patch also requires an operation similar to: git grep "asm/compat\.h" | cut -d ":" -f 1 | xargs -n 1 sed -i -e "s%asm/compat.h%linux/compat.h%g" Cc: acme@kernel.org Cc: benh@kernel.crashing.org Cc: borntraeger@de.ibm.com Cc: catalin.marinas@arm.com Cc: cmetcalf@mellanox.com Cc: cohuck@redhat.com Cc: davem@davemloft.net Cc: deller@gmx.de Cc: devel@driverdev.osuosl.org Cc: gerald.schaefer@de.ibm.com Cc: gregkh@linuxfoundation.org Cc: heiko.carstens@de.ibm.com Cc: hoeppner@linux.vnet.ibm.com Cc: hpa@zytor.com Cc: jejb@parisc-linux.org Cc: jwi@linux.vnet.ibm.com Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-parisc@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-s390@vger.kernel.org Cc: mark.rutland@arm.com Cc: mingo@redhat.com Cc: mpe@ellerman.id.au Cc: oberpar@linux.vnet.ibm.com Cc: oprofile-list@lists.sf.net Cc: paulus@samba.org Cc: peterz@infradead.org Cc: ralf@linux-mips.org Cc: rostedt@goodmis.org Cc: rric@kernel.org Cc: schwidefsky@de.ibm.com Cc: sebott@linux.vnet.ibm.com Cc: sparclinux@vger.kernel.org Cc: sth@linux.vnet.ibm.com Cc: ubraun@linux.vnet.ibm.com Cc: will.deacon@arm.com Cc: x86@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: James Hogan <jhogan@kernel.org> Acked-by: Helge Deller <deller@gmx.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-04-09Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 updates from Martin Schwidefsky: - Improvements for the spectre defense: * The spectre related code is consolidated to a single file nospec-branch.c * Automatic enable/disable for the spectre v2 defenses (expoline vs. nobp) * Syslog messages for specve v2 are added * Enable CONFIG_GENERIC_CPU_VULNERABILITIES and define the attribute functions for spectre v1 and v2 - Add helper macros for assembler alternatives and use them to shorten the code in entry.S. - Add support for persistent configuration data via the SCLP Store Data interface. The H/W interface requires a page table that uses 4K pages only, the code to setup such an address space is added as well. - Enable virtio GPU emulation in QEMU. To do this the depends statements for a few common Kconfig options are modified. - Add support for format-3 channel path descriptors and add a binary sysfs interface to export the associated utility strings. - Add a sysfs attribute to control the IFCC handling in case of constant channel errors. - The vfio-ccw changes from Cornelia. - Bug fixes and cleanups. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (40 commits) s390/kvm: improve stack frame constants in entry.S s390/lpp: use assembler alternatives for the LPP instruction s390/entry.S: use assembler alternatives s390: add assembler macros for CPU alternatives s390: add sysfs attributes for spectre s390: report spectre mitigation via syslog s390: add automatic detection of the spectre defense s390: move nobp parameter functions to nospec-branch.c s390/cio: add util_string sysfs attribute s390/chsc: query utility strings via fmt3 channel path descriptor s390/cio: rename struct channel_path_desc s390/cio: fix unbind of io_subchannel_driver s390/qdio: split up CCQ handling for EQBS / SQBS s390/qdio: don't retry EQBS after CCQ 96 s390/qdio: restrict buffer merging to eligible devices s390/qdio: don't merge ERROR output buffers s390/qdio: simplify math in get_*_buffer_frontier() s390/decompressor: trim uncompressed image head during the build s390/crypto: Fix kernel crash on aes_s390 module remove. s390/defkeymap: fix global init to zero ...
2018-03-26s390/cio: rename struct channel_path_descSebastian Ott
Rename struct channel_path_desc to struct channel_path_desc_fmt0 to fit the scheme. Provide a macro for the function wrappers that gather this and related data from firmware. Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-03-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Fun set of conflict resolutions here... For the mac80211 stuff, these were fortunately just parallel adds. Trivially resolved. In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the function phy_disable_interrupts() earlier in the file, whilst in 'net-next' the phy_error() call from this function was removed. In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the 'rt_table_id' member of rtable collided with a bug fix in 'net' that added a new struct member "rt_mtu_locked" which needs to be copied over here. The mlxsw driver conflict consisted of net-next separating the span code and definitions into separate files, whilst a 'net' bug fix made some changes to that moved code. The mlx5 infiniband conflict resolution was quite non-trivial, the RDMA tree's merge commit was used as a guide here, and here are their notes: ==================== Due to bug fixes found by the syzkaller bot and taken into the for-rc branch after development for the 4.17 merge window had already started being taken into the for-next branch, there were fairly non-trivial merge issues that would need to be resolved between the for-rc branch and the for-next branch. This merge resolves those conflicts and provides a unified base upon which ongoing development for 4.17 can be based. Conflicts: drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f9524 (IB/mlx5: Fix cleanup order on unload) added to for-rc and commit b5ca15ad7e61 (IB/mlx5: Add proper representors support) add as part of the devel cycle both needed to modify the init/de-init functions used by mlx5. To support the new representors, the new functions added by the cleanup patch needed to be made non-static, and the init/de-init list added by the representors patch needed to be modified to match the init/de-init list changes made by the cleanup patch. Updates: drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function prototypes added by representors patch to reflect new function names as changed by cleanup patch drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init stage list to match new order from cleanup patch ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-22s390/qeth: on channel error, reject further cmd requestsJulian Wiedmann
When the IRQ handler determines that one of the cmd IO channels has failed and schedules recovery, block any further cmd requests from being submitted. The request would inevitably stall, and prevent the recovery from making progress until the request times out. This sort of error was observed after Live Guest Relocation, where the pending IO on the READ channel intentionally gets terminated to kick-start recovery. Simultaneously the guest executed SIOCETHTOOL, triggering qeth to issue a QUERY CARD INFO command. The command then stalled in the inoperabel WRITE channel. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-22s390/qeth: lock read device while queueing next bufferJulian Wiedmann
For calling ccw_device_start(), issue_next_read() needs to hold the device's ccwlock. This is satisfied for the IRQ handler path (where qeth_irq() gets called under the ccwlock), but we need explicit locking for the initial call by the MPC initialization. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-22s390/qeth: when thread completes, wake up all waitersJulian Wiedmann
qeth_wait_for_threads() is potentially called by multiple users, make sure to notify all of them after qeth_clear_thread_running_bit() adjusted the thread_running_mask. With no timeout, callers would otherwise stall. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-22s390/qeth: free netdevice when removing a cardJulian Wiedmann
On removal, a qeth card's netdevice is currently not properly freed because the call chain looks as follows: qeth_core_remove_device(card) lx_remove_device(card) unregister_netdev(card->dev) card->dev = NULL !!! qeth_core_free_card(card) if (card->dev) !!! free_netdev(card->dev) Fix it by free'ing the netdev straight after unregistering. This also fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()), where the need to free the current netdevice was not considered at all. Note that free_netdev() takes care of the netif_napi_del() for us too. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-09s390/qeth: reset NAPI context during queue initJulian Wiedmann
init_qdio_queues() resets the Input Queue's overall QDIO state, and positions the buffer cursor back to 0. So this is the obvious place to also reset the queue's NAPI context (in contrast to doing it rather randomly in the middle of the big set_online() path). No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-09s390/qeth: allocate skb from NAPI cacheJulian Wiedmann
napi_alloc_skb() doesn't need to disable IRQs during the allocation, and thus may save us a few cycles. Doing so requires a small fix-up in the HiperTransport path, which currently assumes a fixed NET_SKB_PAD headroom padding. napi_alloc_skb() adds an additional NET_IP_ALIGN padding, so use the proper helper for setting up the mac_header offset. Use this opportunity to convert the non-NAPI path to netdev_alloc_skb(), which means that skb->dev is now always set-up during allocation and doesn't need to be assigned manually. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-09s390/qeth: remove outdated portname debug msgJulian Wiedmann
The 'portname' attribute is deprecated and setting it has no effect. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-09s390/qeth: use __ipa_cmd() for casting an IPA cmd bufferJulian Wiedmann
"s390/qeth: fix SETIP command handling" introduced a new helper, apply it driver-wide. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28s390/qeth: fix IPA command submission raceJulian Wiedmann
If multiple IPA commands are build & sent out concurrently, fill_ipacmd_header() may assign a seqno value to a command that's different from what send_control_data() later assigns to this command's reply. This is due to other commands passing through send_control_data(), and incrementing card->seqno.ipa along the way. So one IPA command has no reply that's waiting for its seqno, while some other IPA command has multiple reply objects waiting for it. Only one of those waiting replies wins, and the other(s) times out and triggers a recovery via send_ipa_cmd(). Fix this by making sure that the same seqno value is assigned to a command and its reply object. Do so immediately before submitting the command & while holding the irq_pending "lock", to produce nicely ascending seqnos. As a side effect, *all* IPA commands now use a reply object that's waiting for its actual seqno. Previously, early IPA commands that were submitted while the card was still DOWN used the "catch-all" IDX seqno. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28s390/qeth: fix overestimated count of buffer elementsJulian Wiedmann
qeth_get_elements_for_range() doesn't know how to handle a 0-length range (ie. start == end), and returns 1 when it should return 0. Such ranges occur on TSO skbs, where the L2/L3/L4 headers (and thus all of the skb's linear data) are skipped when mapping the skb into regular buffer elements. This overestimation may cause several performance-related issues: 1. sub-optimal IO buffer selection, where the next buffer gets selected even though the skb would actually still fit into the current buffer. 2. forced linearization, if the element count for a non-linear skb exceeds QETH_MAX_BUFFER_ELEMENTS. Rather than modifying qeth_get_elements_for_range() and adding overhead to every caller, fix up those callers that are in risk of passing a 0-length range. Fixes: 2863c61334aa ("qeth: refactor calculation of SBALE count") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-09s390/qeth: fix SETIP command handlingJulian Wiedmann
send_control_data() applies some special handling to SETIP v4 IPA commands. But current code parses *all* command types for the SETIP command code. Limit the command code check to IPA commands. Fixes: 5b54e16f1a54 ("qeth: do not spin for SETIP ip assist command") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2024-07-02 04:05:18 +0000