| Age | Commit message (Collapse) | Author |
|---|
|
commit 0f6d93aa9d96cc9022b51bd10d462b03296be146 upstream.
The ACARD driver calls udelay() with a value > 2000, which leads to to
the following compilation error on ARM:
ERROR: "__bad_udelay" [drivers/scsi/atp870u.ko] undefined!
make[1]: *** [__modpost] Error 1
This is because udelay is defined on ARM, roughly speaking, as
#define udelay(n) ((n) > 2000 ? __bad_udelay() : \
__const_udelay((n) * ((2199023U*HZ)>>11)))
The argument to __const_udelay is the number of jiffies to wait divided
by 4, but this does not work unless the multiplication does not
overflow, and that is what the build error is designed to prevent. The
intended behavior can be achieved by using mdelay to call udelay
multiple times in a loop.
[jrnieder@gmail.com: adding context]
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e47f8976d8e573928824a06748f7bc82c58d747f upstream.
A quote from SPC-4: "While in the unavailable primary target port
asymmetric access state, the device server shall support those of
the following commands that it supports while in the active/optimized
state: [ ... ] d) SET TARGET PORT GROUPS; [ ... ]". Hence enable
sending STPG to a target port group that is in the unavailable state.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc3f02a795d3b4faa99d37390174be2a75d091bd upstream.
John reports:
BUG: soft lockup - CPU#2 stuck for 23s! [kworker/u:8:2202]
[..]
Call Trace:
[<ffffffff8141782a>] scsi_remove_target+0xda/0x1f0
[<ffffffff81421de5>] sas_rphy_remove+0x55/0x60
[<ffffffff81421e01>] sas_rphy_delete+0x11/0x20
[<ffffffff81421e35>] sas_port_delete+0x25/0x160
[<ffffffff814549a3>] mptsas_del_end_device+0x183/0x270
...introduced by commit 3b661a9 "[SCSI] fix hot unplug vs async scan race".
Don't restart lookup of more stargets in the multi-target case, just
arrange to traverse the list once, on the assumption that new targets
are always added at the end. There is no guarantee that the target will
change state in scsi_target_reap() so we can end up spinning if we
restart.
Acked-by: Jack Wang <jack_wang@usish.com>
LKML-Reference: <CAEhu1-6wq1YsNiscGMwP4ud0Q+MrViRzv=kcWCQSBNc8c68N5Q@mail.gmail.com>
Reported-by: John Drescher <drescherjm@gmail.com>
Tested-by: John Drescher <drescherjm@gmail.com>
Signed-off-by: Dan Williams <djbw@fb.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d70a74ffd616073a68ae0974d98819bfa8e6da6 upstream.
The oem parameter image embedded in the efi variable is at an offset
from the start of the variable. However, in the failure path we try to
free the 'orom' pointer which is only valid when the paramaters are
being read from the legacy option-rom space.
Since failure to load the oem parameters is unlikely and we keep the
memory around in the success case just defer all de-allocation to devm.
Reported-by: Don Morris <don.morris@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21e89afd325849eb38adccf382df16cc895911f9 upstream.
It turns out Smart Array logical drives do not support target
reset and when the target reset fails, the logical drive will
be taken off line. Symptoms look like this:
hpsa 0000:03:00.0: Abort request on C1:B0:T0:L0
hpsa 0000:03:00.0: resetting device 1:0:0:0
hpsa 0000:03:00.0: cp ffff880037c56000 is reported invalid (probably means target device no longer present)
hpsa 0000:03:00.0: resetting device failed.
sd 1:0:0:0: Device offlined - not ready after error recovery
sd 1:0:0:0: rejecting I/O to offline device
EXT3-fs error (device sdb1): read_block_bitmap:
LUN reset is supported though, and is what we should be using.
Target reset is also disruptive in shared SAS situations,
for example, an external MSA1210m which does support target
reset attached to Smart Arrays in multiple hosts -- a target
reset from one host is disruptive to other hosts as all LUNs
on the target will be reset and will abort all outstanding i/os
back to all the attached hosts. So we should use LUN reset,
not target reset.
Tested this with Smart Array logical drives and with tape drives.
Not sure how this bug survived since 2009, except it must be very
rare for a Smart Array to require more than 30s to complete a request.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 225c56960fcafeccc2b6304f96cd3f0dbf42a16a upstream.
The length field in the host config packet is only 16-bit long, so
passing it 0x10000 (64K which is our standard PAGE_SIZE) doesn't
work and result in an empty config from the server.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
used by sg list
commit 27e99ade81368e6fdda3212bff9345177cf9e57a upstream.
When using the commands below to write some data to a virtio-scsi LUN of the
QEMU guest(32-bit) with 1G physical memory(qemu -m 1024), the qemu will crash.
# sudo mkfs.ext4 /dev/sdb (/dev/sdb is the virtio-scsi LUN.)
# sudo mount /dev/sdb /mnt
# dd if=/dev/zero of=/mnt/file bs=1M count=1024
In current implementation, sg_set_buf is called to add buffers to sg list which
is put into the virtqueue eventually. But if there are some HighMem pages in
table->sgl you can not get virtual address by sg_virt. So, sg_virt(sg_elem) may
return NULL value. This will cause QEMU exit when virtqueue_map_sg is called
in QEMU because an invalid GPA is passed by virtqueue.
Two solutions are discussed here:
http://lkml.indiana.edu/hypermail/linux/kernel/1207.3/00675.html
Finally, value assignment approach was adopted because:
Value assignment creates a well-formed scatterlist, because the termination
marker in source sg_list has been set in blk_rq_map_sg(). The last entry of the
source sg_list is just copied to the the last entry in destination list. Note
that, for now, virtio_ring does not care about the form of the scatterlist and
simply processes the first out_num + in_num consecutive elements of the sg[]
array.
I have tested the patch on my workstation. QEMU would not crash any more.
Signed-off-by: Wang Sen <senwang@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 256d0eaac87da1e993190846064f339f4c7a63f5 upstream.
If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor. CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected. This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not. Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug. This bug should not normally cause a problem for direct
attached disk storage.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6532207116307eb7ecbfa7b9e02c53230096a50 upstream.
This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.
One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets. When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.
This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.
This change only affects Broadcom's 5709 chipset.
Unable to handle kernel NULL pointer dereference at 0000000000000008 RIP:
[<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
Pid: 0, comm: swapper Tainted: G ---- 2.6.18-333.el5debug #2
RIP: 0010:[<ffffffff881f0e7d>] [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
RSP: 0018:ffff8101b575bd50 EFLAGS: 00010216
RAX: 0000000000000005 RBX: ffff81007c5fb180 RCX: 0000000000000000
RDX: 0000000000000ffc RSI: 00000000817e8000 RDI: 0000000000000220
RBP: ffff81015bbd7ec0 R08: ffff8100817e9000 R09: 0000000000000000
R10: ffff81007c5fb180 R11: 00000000000000c8 R12: 000000007a25a010
R13: 0000000000000000 R14: 0000000000000005 R15: ffff810159f80558
FS: 0000000000000000(0000) GS:ffff8101afebc240(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 0000000000201000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffff8101b5754000, task ffff8101afebd820)
Stack: 000000000000000b ffff810159f80000 0000000000000040 ffff810159f80520
ffff810159f80500 00cf00cf8008e84b ffffc200100939e0 ffff810009035b20
0000502900000000 000000be00000001 ffff8100817e7810 00d08101b575bea8
Call Trace:
<IRQ> [<ffffffff8008e0d0>] show_schedstat+0x1c2/0x25b
[<ffffffff881f1886>] :bnx2:bnx2_poll+0xf6/0x231
[<ffffffff8000c9b9>] net_rx_action+0xac/0x1b1
[<ffffffff800125a0>] __do_softirq+0x89/0x133
[<ffffffff8005e30c>] call_softirq+0x1c/0x28
[<ffffffff8006d5de>] do_softirq+0x2c/0x7d
[<ffffffff8006d46e>] do_IRQ+0xee/0xf7
[<ffffffff8005d625>] ret_from_intr+0x0/0xa
<EOI> [<ffffffff801a5780>] acpi_processor_idle_simple+0x1c5/0x341
[<ffffffff801a573d>] acpi_processor_idle_simple+0x182/0x341
[<ffffffff801a55bb>] acpi_processor_idle_simple+0x0/0x341
[<ffffffff80049560>] cpu_idle+0x95/0xb8
[<ffffffff80078b1c>] start_secondary+0x479/0x488
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10cce6d8b5af0b32bc4254ae4a28423a74c0921c upstream.
This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.
[jejb: fix whitespace problems]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4bdd03e61b7a5c4c6bc2b25d46fcd491788fdfb3 upstream.
Commit d38bd3aef ("Add -Werror compilation flag") is causing build breakage
with random gcc incarnations. These look like gcc problems, but we shouldn't
break the build because of a bad gcc. Fix this by adding a make flag
WARNINGS_BECOME_ERRORS=1
which is the same as aic7xxx uses so ordinarily the build doesn't use -Werror
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Alex Iannicelli <alex.iannicelli@emulex.com>
Cc: James Smart <james.smart@emulex.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Mike Pagano <mpagano@gentoo.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit 14216561e164671ce147458653b1fea06a4ada1e upstream.
This is a particularly nasty SCSI ATA Translation Layer (SATL) problem.
SAT-2 says (section 8.12.2)
if the device is in the stopped state as the result of
processing a START STOP UNIT command (see 9.11), then the SATL
shall terminate the TEST UNIT READY command with CHECK CONDITION
status with the sense key set to NOT READY and the additional
sense code of LOGICAL UNIT NOT READY, INITIALIZING COMMAND
REQUIRED;
mpt2sas internal SATL seems to implement this. The result is very confusing
standby behaviour (using hdparm -y). If you suspend a drive and then send
another command, usually it wakes up. However, if the next command is a TEST
UNIT READY, the SATL sees that the drive is suspended and proceeds to follow
the SATL rules for this, returning NOT READY to all subsequent commands. This
means that the ordering of TEST UNIT READY is crucial: if you send TUR and
then a command, you get a NOT READY to both back. If you send a command and
then a TUR, you get GOOD status because the preceeding command woke the drive.
This bit us badly because
commit 85ef06d1d252f6a2e73b678591ab71caad4667bb
Author: Tejun Heo <tj@kernel.org>
Date: Fri Jul 1 16:17:47 2011 +0200
block: flush MEDIA_CHANGE from drivers on close(2)
Changed our ordering on TEST UNIT READY commands meaning that SATA drives
connected to an mpt2sas now suspend and refuse to wake (because the mpt2sas
SATL sees the suspend *before* the drives get awoken by the next ATA command)
resulting in lots of failed commands.
The standard is completely nuts forcing this inconsistent behaviour, but we
have to work around it.
The fix for this is twofold:
1. Set the allow_restart flag so we wake the drive when we see it has been
suspended
2. Return all TEST UNIT READY status directly to the mid layer without any
further error handling which prevents us causing error handling which
may offline the device just because of a media check TUR.
Reported-by: Matthias Prager <linux@matthiasprager.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
command line option to a very small value
commit 338b131a3269881c7431234855c93c219b0979b6 upstream.
If the specified max_queue_depth setting is less than the
expected number of internal commands, then driver will calculate
the queue depth size to a negitive number. This negitive number
is actually a very large number because variable is unsigned
16bit integer. So, the driver will ask for a very large amount of
memory for message frames and resulting into oops as memory
allocation routines will not able to handle such a large request.
So, in order to limit this kind of oops, The driver need to set
the max_queue_depth to a scsi mid layer's can_queue value. Then
the overall message frames required for IO is minimum of either
(max_queue_depth plus internal commands) or the IOC global
credits.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27c419739b67decced4650440829b8d51bef954b upstream.
The following v3.4-rc1 commit unmasked an existing bug in scsi_io_completion's
SG_IO error handling: 47ac56d [SCSI] scsi_error: classify some ILLEGAL_REQUEST
sense as a permanent TARGET_ERROR
Given that certain ILLEGAL_REQUEST are now properly categorized as
TARGET_ERROR the host_byte is being set (before host_byte wasn't ever
set for these ILLEGAL_REQUEST).
In scsi_io_completion, initialize req->errors with cmd->result _after_
the SG_IO block that calls __scsi_error_from_host_byte (which may
modify the host_byte).
Before this fix:
cdb to send: 12 01 01 00 00 00
ioctl(3, SG_IO, {'S', SG_DXFER_NONE, cmd[6]=[12, 01, 01, 00, 00, 00],
mx_sb_len=32, iovec_count=0, dxfer_len=0, timeout=20000, flags=0,
status=02, masked_status=01, sb[19]=[70, 00, 05, 00, 00, 00, 00, 0b,
00, 00, 00, 00, 24, 00, 00, 00, 00, 00, 00], host_status=0x10,
driver_status=0x8, resid=0, duration=0, info=0x1}) = 0
SCSI Status: Check Condition
Sense Information:
sense buffer empty
After:
cdb to send: 12 01 01 00 00 00
ioctl(3, SG_IO, {'S', SG_DXFER_NONE, cmd[6]=[12, 01, 01, 00, 00, 00],
mx_sb_len=32, iovec_count=0, dxfer_len=0, timeout=20000, flags=0,
status=02, masked_status=01, sb[19]=[70, 00, 05, 00, 00, 00, 00, 0b,
00, 00, 00, 00, 24, 00, 00, 00, 00, 00, 00], host_status=0,
driver_status=0x8, resid=0, duration=0, info=0x1}) = 0
SCSI Status: Check Condition
Sense Information:
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid field in cdb
Raw sense data (in hex):
70 00 05 00 00 00 00 0b 00 00 00 00 24 00 00 00
00 00 00
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit bd8d6dd43a77bfd2b8fef5b094b9d6095e169dee upstream.
The following patch moves the poll_aen_lock initializer from
megasas_probe_one() to megasas_init(). This prevents a crash when a user
loads the driver and tries to issue a poll() system call on the ioctl
interface with no adapters present.
Signed-off-by: Kashyap Desai <Kashyap.Desai@lsi.com>
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 940f5d47e2f2e1fa00443921a0abf4822335b54d upstream.
When we call scsi_unprep_request() the command associated with the request
gets destroyed and therefore drops its reference on the device. If this was
the only reference, the device may get released and we end up with a NULL
pointer deref when we call blk_requeue_request.
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
[jejb: enhance commend and add commit log for stable]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67bd94130015c507011af37858989b199c52e1de upstream.
Use blk_queue_dead() to test whether the queue is dead instead
of !sdev. Since scsi_prep_fn() may be invoked concurrently with
__scsi_remove_device(), keep the queuedata (sdev) pointer in
__scsi_remove_device(). This patch fixes a kernel oops that
can be triggered by USB device removal. See also
http://www.spinics.net/lists/linux-scsi/msg56254.html.
Other changes included in this patch:
- Swap the blk_cleanup_queue() and kfree() calls in
scsi_host_dev_release() to make that code easier to grasp.
- Remove the queue dead check from scsi_run_queue() since the
queue state can change anyway at any point in that function
where the queue lock is not held.
- Remove the queue dead check from the start of scsi_request_fn()
since it is redundant with the scsi_device_online() check.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b661a92e869ebe2358de8f4b3230ad84f7fce51 upstream.
The following crash results from cases where the end_device has been
removed before scsi_sysfs_add_sdev has had a chance to run.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000098
IP: [<ffffffff8115e100>] sysfs_create_dir+0x32/0xb6
...
Call Trace:
[<ffffffff8125e4a8>] kobject_add_internal+0x120/0x1e3
[<ffffffff81075149>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff8125e641>] kobject_add_varg+0x41/0x50
[<ffffffff8125e70b>] kobject_add+0x64/0x66
[<ffffffff8131122b>] device_add+0x12d/0x63a
[<ffffffff814b65ea>] ? _raw_spin_unlock_irqrestore+0x47/0x56
[<ffffffff8107de15>] ? module_refcount+0x89/0xa0
[<ffffffff8132f348>] scsi_sysfs_add_sdev+0x4e/0x28a
[<ffffffff8132dcbb>] do_scan_async+0x9c/0x145
...teach scsi_sysfs_add_devices() to check for deleted devices() before
trying to add them, and teach scsi_remove_target() how to remove targets
that have not been added via device_add().
Reported-by: Dariusz Majchrzak <dariusz.majchrzak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57fc2e335fd3c2f898ee73570dc81426c28dc7b4 upstream.
Rapid ata hotplug on a libsas controller results in cases where libsas
is waiting indefinitely on eh to perform an ata probe.
A race exists between scsi_schedule_eh() and scsi_restart_operations()
in the case when scsi_restart_operations() issues i/o to other devices
in the sas domain. When this happens the host state transitions from
SHOST_RECOVERY (set by scsi_schedule_eh) back to SHOST_RUNNING and
->host_busy is non-zero so we put the eh thread to sleep even though
->host_eh_scheduled is active.
Before putting the error handler to sleep we need to check if the
host_state needs to return to SHOST_RECOVERY for another trip through
eh. Since i/o that is released by scsi_restart_operations has been
blocked for at least one eh cycle, this implementation allows those
i/o's to run before another eh cycle starts to discourage hung task
timeouts.
Reported-by: Tom Jackson <thomas.p.jackson@intel.com>
Tested-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b17caa174a7e1fd2e17b26e210d4ee91c4c28b37 upstream.
commit 198439e4 [SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
commit 19252de6 [SCSI] libsas: fix wide port hotplug issues
The above commits seem to have confused the return value of
sas_ex_discover_dev which is non-zero on failure and
sas_ex_join_wide_port which just indicates short circuiting discovery on
already established ports. The result is random discovery failures
depending on configuration.
Calls to sas_ex_join_wide_port are the source of the trouble as its
return value is errantly assigned to 'res'. Convert it to bool and stop
returning its result up the stack.
Tested-by: Dan Melnic <dan.melnic@amd.com>
Reported-by: Dan Melnic <dan.melnic@amd.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26f2f199ff150d8876b2641c41e60d1c92d2fb81 upstream.
Continue running revalidation until no more broadcast devices are
discovered. Fixes cases where re-discovery completes too early in a
domain with multiple expanders with pending re-discovery events.
Servicing BCNs can get backed up behind error recovery.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit a7a20d103994 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d0137 ("fix async probe
regression"), so that same commit a7a20d103994 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: linux-scsi <linux-scsi@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The netdev->base_addr parameter has been deprecated in the L2 bnx2
driver. This is used by bnx2i for the BARn iomapping.
This patch will directly reference the pci_resource_start instead
of using the deprecated netdev->base_addr.
This patch is actually a critical bug fix as the 1G bnx2 driver no
longer supports the netdev->base_addr in the current kernel of the scsi
tree. This means that Broadcom's 1G Linux iSCSI offload solution would
not work at all without this patch.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fill_result_tf() grabs the taskfile flags from the originating qc which
sas_ata_qc_fill_rtf() promptly overwrites. The presence of an
ata_taskfile in the sata_device makes it tempting to just copy the full
contents in sas_ata_qc_fill_rtf(). However, libata really only wants
the fis contents and expects the other portions of the taskfile to not
be touched by ->qc_fill_rtf. To that end store a fis buffer in the
sata_device and use ata_tf_from_fis() like every other ->qc_fill_rtf()
implementation.
Cc: <stable@vger.kernel.org>
Reported-by: Praveen Murali <pmurali@logicube.com>
Tested-by: Praveen Murali <pmurali@logicube.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pull target fixes from Nicholas Bellinger:
"Two minor target fixes. There is really nothing exciting and/or
controversial this time around.
There's one fix from MDR for a RCU debug warning message within tcm_fc
code (CC'ed to stable), and a small AC fix for qla_target.c based upon
a recent Coverity static report.
Also, there is one other outstanding virtio-scsi LUN scanning bugfix
that has been uncovered with the in-flight tcm_vhost driver over the
last days, and that needs to make it into 3.5 final too. This patch
has been posted to linux-scsi again here:
http://marc.info/?l=linux-scsi&m=134160609212542&w=2
and I've asked James to include it in his next PULL request."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: print the right array elements in qlt_async_event
tcm_fc: Resolve suspicious RCU usage warnings
|
|
Based upon Alan's patch from Coverity scan id 793583, these debug
messages in qlt_async_event() should be starting from byte 0, which is
always the Asynchronous Event Status Code from the parent switch statement.
Also, rename reason_code -> login_code following the language used in
2500 FW spec for Port Database Changed (0x8014) -> Port Database Changed
Event Mailbox Register for mailbox[2].
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly. They
report bogus sizes, in some cases becoming unusable as a result.
The bugs were triggered by commit
09b6b51b0b6c1b9bb61815baf205e4d74c89ff04 (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices. By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.
It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly. Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.
Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device. If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.
This fixes Bugzilla #43391.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a couple of minor fixes, one for a preempt warning in the
mpt2sas driver and one is a config failure with the new sd async
domain."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix sd_probe_domain config problem
[SCSI] mpt2sas: Fix unsafe using smp_processor_id() in preemptible
|
|
version.h header file is no longer required for qla_target code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If we make a variable an unsigned int and then expect it to be < 0 on
a bad character, we're going to have a bad time. Fix the tcm_qla2xxx
code to actually notice if hex_to_bin() returns a negative variable.
This was detected by the compiler warning:
scsi/qla2xxx/tcm_qla2xxx.c: In function ‘tcm_qla2xxx_npiv_extract_wwn’:
scsi/qla2xxx/tcm_qla2xxx.c:148:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If we go to the "out_term:" exit path in qlt_do_work(), we call
qlt_send_term_exchange() with a NULL cmd, which means that it can't
possibly free the cmd for us. Add an explicit call to free the
command memory, so we don't leak the allocation.
This will also fix warnings about "BUG qla_tgt_cmd_cachep: Objects
remaining on kmem_cache_close" from slub when unloading the qla2xxx
target module.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In qlt_do_ctio_completion(), there's no point in calling
qlt_term_ctio_exchange() with a NULL cmd -- all that it does is crash
in a NULL pointer dereference, since it does
qlt_send_term_exchange(vha, cmd, &cmd->atio, 1);
and dereferencing &cmd->atio is a bad idea if cmd itself is NULL.
If we really need to do this, we could take the values from the
failed CTIO we're processing, but it's not clear if it's worth
the replumbing to do that.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When we create an explicit node ACL in tcm_qla2xxx_make_nodeacl(),
there is a call to tcm_qla2xxx_setup_nacl_from_rport(), which puts the
node ACL into the lport_fcport_map even though there is no session yet
for the initiator. Since the only time we remove entries from this
map is when we free a session, this means that if we later delete this
node ACL without the initiator ever creating a session, we'll leave
the nacl pointer in the btree pointing at freed memory.
This is especially bad if that initiator later does send us a command
that would cause us to create a dynamic ACL and session: we'll find
the stale freed nacl pointer in the btree and end up with use-after-free.
We could add more code to clear the btree entry when deleting the
explicit nacl, but the original insertion is pointless: without a
session attached, we'll just have to update the entry when a session
appears anyway. So we can just delete tcm_qla2xxx_setup_nacl_from_rport()
and the code that calls it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a new tcm_qla2xxx_clear_sess_lookup() call to clear session
specific s_id + loop_id entries used for se_node_acl pointer lookup ahead
of releasing se_session within the process context workqueue callback in
tcm_qla2xxx_free_session().
It makes the call in existing tcm_qla2xxx_clear_nacl_from_fcport_map()
code invoked from qlt_unreg_sess() in interrupt context w/ hardware_lock
held, ahead of the process context callback into qlt_free_session_done()
-> tcm_qla2xxx_free_session().
We are doing this to address a race between incoming ATIO or TMR packets
using stale se_node_acl pointer once session shutdown has been invoked via
qlt_unreg_sess() in qla_target.c LLD code, and when the entire tcm_qla2xxx
endpoint has not been forced into shutdown w/ echo 0 > ../$QLA2XXX_PORT/enable
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch converts tcm_qla2xxx code to use an internal kref_put() for
se_session->sess_kref in order to ensure that qla_hw_data->hardware_lock
can be held while calling qlt_unreg_sess() for the final put.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
With CONFIG_BLK_DEV_SD = n and CONFIG_PM = n, you get this compile failure:
(.text+0x4f6c77): undefined reference to `scsi_sd_probe_domain'
This was introduced by
commit a7a20d103994fd760766e6c9d494daa569cbfe06
Author: Dan Williams <dan.j.williams@intel.com>
Date: Thu Mar 22 17:05:11 2012 -0700
[SCSI] sd: limit the scope of the async probe domain
And happens because scsi_sd_probe_domain is conditionally defined but
unconditionally used. Fix this by making the symbol unconditionally defined.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When CONFIG_DEBUG_PREEMPT is enabled, bug is observed in the smp_processor_id().
This is because smp_processor_id() is not called in preempt safe condition.
To fix this issue, use raw_smp_processor_id instead of smp_processor_id.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pull final round of SCSI updates from James Bottomley:
"This is primarily another round of driver updates (bnx2fc, qla2xxx,
qla4xxx) including the target mode driver for qla2xxx. We've also got
a couple of regression fixes (async scanning, broken this merge window
and a fix to a long standing break in the scsi_wait_scan module)."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (45 commits)
[SCSI] fix scsi_wait_scan
[SCSI] fix async probe regression
[SCSI] be2iscsi: fix dma free size mismatch regression
[SCSI] qla4xxx: Update driver version to 5.02.00-k17
[SCSI] qla4xxx: Capture minidump for ISP82XX on firmware failure
[SCSI] qla4xxx: Add change_queue_depth API support
[SCSI] qla4xxx: Fix clear ddb mbx command failure issue.
[SCSI] qla4xxx: Fix kernel panic during discovery logout.
[SCSI] qla4xxx: Correct early completion of pending mbox.
[SCSI] fcoe, bnx2fc, libfcoe: SW FCoE and bnx2fc use FCoE Syfs
[SCSI] libfcoe: Add fcoe_sysfs
[SCSI] bnx2fc: Allocate fcoe_ctlr with bnx2fc_interface, not as a member
[SCSI] fcoe: Allocate fcoe_ctlr with fcoe_interface, not as a member
[SCSI] Fix dm-multipath starvation when scsi host is busy
[SCSI] ufs: fix potential NULL pointer dereferencing error in ufshcd_prove.
[SCSI] qla2xxx: don't free pool that wasn't allocated
[SCSI] mptfusion: unlock on error in mpt_config()
[SCSI] tcm_qla2xxx: Add >= 24xx series fabric module for target-core
[SCSI] qla2xxx: Add LLD target-mode infrastructure for >= 24xx series
[SCSI] Revert "qla2xxx: During loopdown perform Diagnostic loopback."
...
|
|
Commit c751085943362143f84346d274e0011419c84202
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date: Sun Apr 12 20:06:56 2009 +0200
PM/Hibernate: Wait for SCSI devices scan to complete during resume
Broke the scsi_wait_scan module in 2.6.30. Apparently debian still uses it so
fix it and backport to stable before removing it in 3.6.
The breakage is caused because the function template in
include/scsi/scsi_scan.h is defined to be a nop unless SCSI is built in.
That means that in the modular case (which is every distro), the
scsi_wait_scan module does a simple async_synchronize_full() instead of
waiting for scans.
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Commit a7a20d1 "[SCSI] sd: limit the scope of the async probe domain"
moved sd probe work out of reach of wait_for_device_probe(). Allow it
to be synced via scsi_complete_async_scans().
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch should go into 3.5 fixes. The bug was added in the
patches for the 3.5 feature window.
As you can see from the patch I made a mistake. During
development I switched from passing a struct to the size of
the struct, but left the sizeof. This results in us allocating
4 bytes (sizeof(int)) but then calling pci_free_consistent
with the size of the struct.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added support to capture dump (Minidump) which allows us to
catpure a snapshot of the firmware/hardware states at the time
of firmware failure
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
change_queue_depth will adjust device queuedepth upon receiving
"SAM_STAT_TASK_SET_FULL" scsi status from the target.
Also added ql4xqfulltracking command line param to enable or disable
queuefull tracking. One can disabling queuefull tracking to ensure
user set scsi device queuedepth is not altered.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Allow ddb state to change to DDB_DS_NO_CONNECTION_ACTIVE or
DDB_DS_SESSION_FAILED before issuing clear ddb mailbox cmd,
because clear ddb mailbox cmd fails if the ddb state is not
equal to DDB_DS_NO_CONNECTION_ACTIVE or DDB_DS_SESSION_FAILED.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Update the session and connection parameter before sending
connection logged in event to iscsiadm because in some
scenario logout may come in just after we send the logged
in event to user, which free up session, connection and ddb,
but DPC is still updating session and connect parameter
which can lead to panic.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Check for Firmware Hang (AF_FW_RECOVERY) after mailbox command
has gained access to ensure that the mailbox command does not
wait un-necessarily during a firmware recovery and prevent
premature mailbox timeout which will lead to back to back reset's.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61ad3: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
|
|
This patch has the SW FCoE driver and the bnx2fc
driver make use of the new fcoe_sysfs API added
earlier in this patch series.
After this patch a fcoe_ctlr_device is allocated with
private data in this order.
+------------------+ +------------------+
| fcoe_ctlr_device | | fcoe_ctlr_device |
+------------------+ +------------------+
| fcoe_ctlr | | fcoe_ctlr |
+------------------+ +------------------+
| fcoe_interface | | bnx2fc_interface |
+------------------+ +------------------+
libfcoe also takes part in this new model since it
discovers and manages fcoe_fcf instances. The memory
allocation is different for FCFs. I didn't want to
impact libfcoe's fcoe_fcf processing, so this patch
creates fcoe_fcf_device instances for each discovered
fcoe_fcf. The two are paired using a (void * priv)
member of the fcoe_ctlr_device. This allows libfcoe
to continue maintaining its list of fcoe_fcf instances
and simply attaches and detaches them from existing
or new fcoe_fcf_device instances.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
