summaryrefslogtreecommitdiff
path: root/drivers/tty
AgeCommit message (Collapse)Author
2012-10-17serial: pl011: handle corruption at high clock speedsLinus Walleij
commit c5dd553b9fd069892c9e2de734f4f604e280fa7a upstream. This works around a few glitches in the ST version of the PL011 serial driver when using very high baud rates, as we do in the Ux500: 3, 3.25, 4 and 4.05 Mbps. Problem Observed/rootcause: When using high baud-rates, and the baudrate*8 is getting close to the provided clock frequency (so a division factor close to 1), when using bursts of characters (so they are abutted), then it seems as if there is not enough time to detect the beginning of the start-bit which is a timing reference for the entire character, and thus the sampling moment of character bits is moving towards the end of each bit, instead of the middle. Fix: Increase slightly the RX baud rate of the UART above the theoretical baudrate by 5%. This will definitely give more margin time to the UART_RX to correctly sample the data at the middle of the bit period. Also fix the ages old copy-paste error in the very stressed comment, it's referencing the registers used in the PL010 driver rather than the PL011 ones. Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com> Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com> Signed-off-by: Matthias Locher <matthias.locher@stericsson.com> Signed-off-by: Rajanikanth HV <rajanikanth.hv@stericsson.com> Cc: Bibek Basu <bibek.basu@stericsson.com> Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17serial: set correct baud_base for EXSYS EX-41092 Dual 16950Flavio Leitner
commit 26e8220adb0aec43b7acafa0f1431760eee28522 upstream. Apparently the same card model has two IDs, so this patch complements the commit 39aced68d664291db3324d0fcf0985ab5626aac2 adding the missing one. Signed-off-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17n_gsm: memory leak in uplink error pathRuss Gorby
commit 88ed2a60610974443335c924d7cb8e5dcf9dbdc1 upstream. Uplink (TX) network data will go through gsm_dlci_data_output_framed there is a bug where if memory allocation fails, the skb which has already been pulled off the list will be lost. In addition TX skbs were being processed in LIFO order Fixed the memory leak, and changed to FIFO order processing Signed-off-by: Russ Gorby <russ.gorby@intel.com> Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17n_gsm: replace kfree_skb w/ appropriate dev_* versionsRuss Gorby
commit 329e56780e514a7ab607bcb51a52ab0dc2669414 upstream. Drivers are supposed to use the dev_* versions of the kfree_skb interfaces. In a couple of cases we were called with IRQs disabled as well which kfree_skb() does not expect. Replaced kfree_skb calls w/ dev_kfree_skb and dev_kfree_skb_any Signed-off-by: Russ Gorby <russ.gorby@intel.com> Tested-by: Yin, Fengwei <fengwei.yin@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17n_gsm: avoid accessing freed memory during CMD_FCOFF conditionRuss Gorby
commit b4338e1efc339986cf6c0a3652906e914a86e2d3 upstream. gsm_data_kick was recently modified to allow messages on the tx queue bound for DLCI0 to flow even during FCOFF conditions. Unfortunately we introduced a bug discovered by code inspection where subsequent list traversers can access freed memory if the DLCI0 messages were not all at the head of the list. Replaced singly linked tx list w/ a list_head and used provided interfaces for traversing and deleting members. Signed-off-by: Russ Gorby <russ.gorby@intel.com> Tested-by: Yin, Fengwei <fengwei.yin@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17n_gsm: added interlocking for gsm_data_lock for certain code pathsRuss Gorby
commit 5e44708f75b0f8712da715d6babb0c21089b2317 upstream. There were some locking holes in the management of the MUX's message queue for 2 code paths: 1) gsmld_write_wakeup 2) receipt of CMD_FCON flow-control message In both cases gsm_data_kick is called w/o locking so it can collide with other other instances of gsm_data_kick (pulling messages tx_tail) or potentially other instances of __gsm_data_queu (adding messages to tx_head) Changed to take the tx_lock in these 2 cases Signed-off-by: Russ Gorby <russ.gorby@intel.com> Tested-by: Yin, Fengwei <fengwei.yin@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17char: n_gsm: remove message filtering for contipated DLCIsamix.lebsir
commit 10c6c383e43565c9c6ec07ff8eb2825f8091bdf0 upstream. The design of uplink flow control in the mux driver is that for constipated channels data will backup into the per-channel fifos, and any messages that make it to the outbound message queue will still go out. Code was added to also stop messages that were in the outbound queue but this requires filtering through all the messages on the queue for stopped dlcis and changes some of the mux logic unneccessarily. The message fiiltering was removed to be in line w/ the original design as the message filtering does not provide any solution. Extra debug messages used during investigation were also removed. Signed-off-by: samix.lebsir <samix.lebsir@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17n_gsm : Flow control handling in Mux driverFrederic Berat
commit c01af4fec2c8f303d6b3354d44308d9e6bef8026 upstream. - Correcting handling of FCon/FCoff in order to respect 27.010 spec - Consider FCon/off will overide all dlci flow control except for dlci0 as we must be able to send control frames. - Dlci constipated handling according to FC, RTC and RTR values. - Modifying gsm_dlci_data_kick and gsm_dlci_data_sweep according to dlci constipated value Signed-off-by: Frederic Berat <fredericx.berat@intel.com> Signed-off-by: Russ Gorby <russ.gorby@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17n_gsm: uplink SKBs accumulate on listRuss Gorby
commit 192b6041e75bb4a2aae73834037038cea139a92d upstream. gsm_dlci_data_kick will not call any output function if tx_bytes > THRESH_LO furthermore it will call the output function only once if tx_bytes == 0 If the size of the IP writes are on the order of THRESH_LO we can get into a situation where skbs accumulate on the outbound list being starved for events to call the output function. gsm_dlci_data_kick now calls the sweep function when tx_bytes==0 Signed-off-by: Russ Gorby <russ.gorby@intel.com> Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17n_gsm.c: Implement 3GPP27.010 DLC start-up procedure in MUXxiaojin
commit 7e8ac7b23b67416700dfb8b4136a4e81ce675b48 upstream. In 3GPP27.010 5.8.1, it defined: The TE multiplexer initiates the establishment of the multiplexer control channel by sending a SABM frame on DLCI 0 using the procedures of clause 5.4.1. Once the multiplexer channel is established other DLCs may be established using the procedures of clause 5.4.1. This patch implement 5.8.1 in MUX level, it make sure DLC0 is the first channel to be setup. [or for those not familiar with the specification: it was possible to try and open a data connection while the control channel was not yet fully open, which is a spec violation and confuses some modems] Signed-off-by: xiaojin <jin.xiao@intel.com> Tested-by: Yin, Fengwei <fengwei.yin@intel.com> [tweaked the order we check things and error code] Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-17Remove BUG_ON from n_tty_read()Stanislav Kozina
commit e9490e93c1978b6669f3e993caa3189be13ce459 upstream. Change the BUG_ON to WARN_ON and return in case of tty->read_buf==NULL. We want to track a couple of long standing reports of this but at the same time we can avoid killing the box. Signed-off-by: Stanislav Kozina <skozina@redhat.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-10-10pch_uart: Add eg20t_port lock field, avoid recursive spinlocksDarren Hart
commit 2588aba002d14e938c2f56d299ecf3e7ce1302a5 upstream. pch_uart_interrupt() takes priv->port.lock which leads to two recursive spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one otherwise): pch_uart_interrupt spin_lock_irqsave(priv->port.lock, flags) case PCH_UART_IID_RDR_TO (data ready) handle_rx_to push_rx tty_port_tty_get spin_lock_irqsave(&port->lock, flags) <--- already hold this lock ... tty_flip_buffer_push ... flush_to_ldisc spin_lock_irqsave(&tty->buf.lock) spin_lock_irqsave(&tty->buf.lock) disc->ops->receive_buf(tty, char_buf) n_tty_receive_buf tty->ops->flush_chars() uart_flush_chars uart_start spin_lock_irqsave(&port->lock) <--- already hold this lock Avoid this by using a dedicated lock to protect the eg20t_port structure and IO access to its membase. This is more consistent with the 8250 driver. Ensure priv->lock is always take prior to priv->port.lock when taken at the same time. V2: Remove inadvertent whitespace change. V3: Account for oops_in_progress for the private lock in pch_console_write(). Note: Like the 8250 driver, if a printk is introduced anywhere inside the pch_console_write() critical section, the kernel will hang on a recursive spinlock on the private lock. The oops case is handled by using a trylock in the oops_in_progress case. Signed-off-by: Darren Hart <dvhart@linux.intel.com> CC: Tomoya MORINAGA <tomoya.rohm@gmail.com> CC: Feng Tang <feng.tang@intel.com> CC: Alexander Stein <alexander.stein@systec-electronic.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: - Adjust context - Drop changes to pch_console_write()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-09-19tty: serial: imx: don't reinit clock in imx_setup_ufcr()Dirk Behme
commit 7be0670f7b9198382938a03ff3db7f47ef6b4780 upstream. Remove the clock configuration from imx_setup_ufcr(). This isn't needed here and will cause garbage output if done. To be be sure that we only touch the bits we want (TXTL and RXTL) we have to mask out all other bits of the UFCR register. Add one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6). Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Shawn Guo <shawn.guo@linaro.org> CC: Sascha Hauer <s.hauer@pengutronix.de> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Xinyu Chen <xinyu.chen@freescale.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: deleted code in imx_setup_ufcr() refers to sport->clk not sport->clk_per] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-09-19tty: serial: imx: console write routing is unsafe on SMPXinyu Chen
commit 9ec1882df244c4ee1baa692676fef5e8b0f5487d upstream. The console feature's write routing is unsafe on SMP with the startup/shutdown call. There could be several consumers of the console * the kernel printk * the init process using /dev/kmsg to call printk to show log * shell, which open /dev/console and write with sys_write() The shell goes into the normal uart open/write routing, but the other two go into the console operations. The open routing calls imx serial startup, which will write USR1/2 register without any lock and critical with imx_console_write call. Add a spin_lock for startup/shutdown/console_write routing. This patch is a port from Freescale's Android kernel. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com> Tested-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-09-12pmac_zilog,kdb: Fix console poll hook to return instead of loopJason Wessel
commit 38f8eefccf3a23c4058a570fa2938a4f553cf8e0 upstream. kdb <-> kgdb transitioning does not work properly with this UART driver because the get character routine loops indefinitely as opposed to returning NO_POLL_CHAR per the expectation of the KDB I/O driver API. The symptom is a kernel hang when trying to switch debug modes. Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-08-10pch_uart: Fix parity setting issueTomoya MORINAGA
commit 38bd2a1ac736901d1cf4971c78ef952ba92ef78b upstream. Parity Setting value is reverse. E.G. In case of setting ODD parity, EVEN value is set. This patch inverts "if" condition. Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-08-10pch_uart: Fix rx error interrupt setting issueTomoya MORINAGA
commit 9539dfb7ac1c84522fe1f79bb7dac2990f3de44a upstream. Rx Error interrupt(E.G. parity error) is not enabled. So, when parity error occurs, error interrupt is not occurred. As a result, the received data is not dropped. This patch adds enable/disable rx error interrupt code. Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [Backported by Tomoya MORINGA: adjusted context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-08-10pch_uart: Fix missing break for 16 byte fifoAlan Cox
commit 9bc03743fff0770dc5a5324ba92e67cc377f16ca upstream. Otherwise we fall back to the wrong value. Reported-by: <dcb314@hotmail.com> Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44091 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-05-31tty: Allow uart_register/unregister/registerAlan Cox
commit 1e66cded334e6cea596c72f6f650eec351b1e959 upstream. This is legitimate but because we don't clear the drv->state pointer in the unregister code causes a bogus BUG(). Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42880 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-05-31Add missing call to uart_update_timeout()Lothar Waßmann
commit 8b979f7c6bf13a57e7b6002f1175312a44773960 upstream. This patch fixes a problem reported here: http://article.gmane.org/gmane.linux.ports.arm.kernel/155242/match=auart Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-05-318250.c: less than 2400 baud fix.Christian Melki
commit f9a9111b540fd67db5dab332f4b83d86c90e27b1 upstream. We noticed that we were loosing data at speed less than 2400 baud. It turned out our (TI16750 compatible) uart with 64 byte outgoing fifo was truncated to 16 byte (bit 5 sets fifo len) when modifying the fcr reg. The input code still fills the buffer with 64 bytes if I remember correctly and thus data is lost. Our fix was to remove whiping of the fcr content and just add the TRIGGER_1 which we want for latency. I can't see why this would not work on less than 2400 always, for all uarts ... Otherwise one would have to make sure the filling of the fifo re-checks the current state of available fifo size (urrk). Signed-off-by: Christian Melki <christian.melki@ericsson.se> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust filename; replace *port with up->port] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-05-318250_pci: fix pch uart matchingArnaud Patard
commit aaa10eb1d0034eccc096f583fe308f0921617598 upstream. The rules used to make 8250_pci "ignore" the PCH uarts are lacking pci subids entries, preventing it to match and thus is breaking serial port support for theses systems. This has been tested on a nanoETXexpress-TT, which has a specifici uart clock. Tested-by: Erwan Velu <Erwan.Velu@zodiacaerospace.com> Signed-off-by: Arnaud Patard <apatard@hupstream.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-05-11drivers/tty/amiserial.c: add missing tty_unlockJulia Lawall
commit d3a7b83f865b46bb7b5e1ed18a129ce1af349db4 upstream. tty_unlock is used on all other exits from the function. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-05-11pch_uart: Fix dma channel unallocated issueTomoya MORINAGA
commit af6d17cdc8c89aeb3101f0d27cd32fc0592b40b2 upstream. This driver anticipates pch_uart_verify_port() is not called during installation. However, actually pch_uart_verify_port() is called during installation. As a result, memory access violation occurs like below. 0. initial value: use_dma=0 1. starup() - dma channel is not allocated because use_dma=0 2. pch_uart_verify_port() - Set use_dma=1 3. UART processing acts DMA mode because use_dma=1 - memory access violation occurs! This patch fixes the issue. Solution: Whenever pch_uart_verify_port() is called and then dma channel is not allocated, the channel should be allocated. Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-05-11ARM: clps711x: serial driver hungs are a result of call disable_irq within ISRAlexander Shiyan
commit 7a6fbc9a887193a1e9f8658703881c528040afbc upstream. Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result of call disable_irq from ISR. synchronize_irq waits for end of interrupt and goes to infinite loop. This patch fix this problem. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
2012-04-22serial: PL011: move interrupt clearingLinus Walleij
commit c3d8b76f61586714cdc5f219ba45592a54caaa55 upstream. Commit 360f748b204275229f8398cb2f9f53955db1503b "serial: PL011: clear pending interrupts" attempts to clear interrupts by writing to a yet-unassigned memory address. This fixes the issue. The breaking patch is marked for stable so should be carried along with the other patch. Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Nicolas Pitre <nico@fluxnic.net> Reported-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-22serial: PL011: clear pending interruptsLinus Walleij
commit 9b96fbacda34079dea0638ee1e92c56286f6114a upstream. Chanho Min reported that when the boot loader transfers control to the kernel, there may be pending interrupts causing the UART to lock up in an eternal loop trying to pick tokens from the FIFO (since the RX interrupt flag indicates there are tokens) while in practice there are no tokens - in fact there is only a pending IRQ flag. This patch address the issue with a combination of two patches suggested by Russell King that clears and mask all interrupts at probe() and clears any pending error and RX interrupts at port startup time. We suspect the spurious interrupts are a side-effect of switching the UART from FIFO to non-FIFO mode. Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com> Reported-by: Chanho Min <chanho0207@gmail.com> Suggested-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Jong-Sung Kim <neidhard.kim@lge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-22pch_uart: Fix MSI setting issueTomoya MORINAGA
commit 867c902e07d5677e2a5b54c0435e589513abde48 upstream. The following patch (MSI setting) is not enough. commit e463595fd9c752fa4bf06b47df93ef9ade3c7cf0 Author: Alexander Stein <alexander.stein@systec-electronic.com> Date: Mon Jul 4 08:58:31 2011 +0200 pch_uart: Add MSI support Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> To enable MSI mode, PCI bus-mastering must be enabled. This patch enables the setting. cc: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-22tty: serial: altera_uart: Check for NULL platform_data in probe.Yuriy Kozlov
commit acede70d6561f2d042d9dbb153d9a3469479c0ed upstream. Follow altera_jtag_uart. This fixes a crash if there is a mistake in the DTS. Signed-off-by: Yuriy Kozlov <ykozlov@ptcusa.com> Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-02serial: sh-sci: fix a race of DMA submit_tx on transferYoshii Takashi
commit 49d4bcaddca977fffdea8b0b71f6e5da96dac78e upstream. When DMA is enabled, sh-sci transfer begins with uart_start() sci_start_tx() if (cookie_tx < 0) schedule_work() Then, starts DMA when wq scheduled, -- (A) process_one_work() work_fn_rx() cookie_tx = desc->submit_tx() And finishes when DMA transfer ends, -- (B) sci_dma_tx_complete() async_tx_ack() cookie_tx = -EINVAL (possible another schedule_work()) This A to B sequence is not reentrant, since controlling variables (for example, cookie_tx above) are not queues nor lists. So, they must be invoked as A B A B..., otherwise results in kernel crash. To ensure the sequence, sci_start_tx() seems to test if cookie_tx < 0 (represents "not used") to call schedule_work(). But cookie_tx will not be set (to a cookie, also means "used") until in the middle of work queue scheduled function work_fn_tx(). This gap between the test and set allows the breakage of the sequence under the very frequently call of uart_start(). Another gap between async_tx_ack() and another schedule_work() results in the same issue, too. This patch introduces a new condition "cookie_tx == 0" just to mark it is "busy" and assign it within spin-locked region to fill the gaps. Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com> Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-02TTY: Wrong unicode value copied in con_set_unimap()Liz Clark
commit 4a4c61b7ce26bfc9d49ea4bd121d52114bad9f99 upstream. Bugzilla 40012: PIO_UNIMAP bug: error updating Unicode-to-font map https://bugzilla.kernel.org/show_bug.cgi?id=40012 The unicode font map for the virtual console is a 32x32x64 table which allocates rows dynamically as entries are added. The unicode value increases sequentially and should count all entries even in empty rows. The defect is when copying the unicode font map in con_set_unimap(), the unicode value is not incremented properly. The wrong unicode value is entered in the new font map. Signed-off-by: Liz Clark <liz.clark@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-02tty: moxa: fix bit test in moxa_start()Dan Carpenter
commit 58112dfbfe02d803566a2c6c8bd97b5fa3c62cdc upstream. This is supposed to be doing a shift before the comparison instead of just doing a bitwise AND directly. The current code means the start() just returns without doing anything. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-12tty/powerpc: early udbg consoles can't be modulesStephen Rothwell
commit f21c6d4a49179f91fd70a41382382f08c780d425 upstream. Fixes these build errors: ERROR: ".udbg_printf" [drivers/tty/ehv_bytechan.ko] undefined! ERROR: ".register_early_udbg_console" [drivers/tty/ehv_bytechan.ko] undefined! ERROR: "udbg_putc" [drivers/tty/ehv_bytechan.ko] undefined! Cc: Timur Tabi <timur@freescale.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layerSamuel Thibault
commit cbcb8346054073d000ecac324763372d6abd44ac upstream. KDFONTOP(GET) currently fails with EIO when being run in a 32bit userland with a 64bit kernel if the font width is not 8. This is because of the setting of the KD_FONT_FLAG_OLD flag, which makes con_font_get return EIO in such case. This flag should *not* be set for KDFONTOP, since it's actually the whole point of this flag (see comment in con_font_set for instance). Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Cc: Arthur Taylor <art@ified.ca> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03jsm: Fixed EEH recovery errorLucas Kannebley Tavares
commit 26aa38cafae0dbef3b2fe75ea487c83313c36d45 upstream. There was an error on the jsm driver that would cause it to be unable to recover after a second error is detected. At the first error, the device recovers properly: [72521.485691] EEH: Detected PCI bus error on device 0003:02:00.0 [72521.485695] EEH: This PCI device has failed 1 times in the last hour: ... [72532.035693] ttyn3 at MMIO 0x0 (irq = 49) is a jsm [72532.105689] jsm: Port 3 added However, at the second error, it cascades until EEH disables the device: [72631.229549] Call Trace: ... [72641.725687] jsm: Port 3 added [72641.725695] EEH: Detected PCI bus error on device 0003:02:00.0 [72641.725698] EEH: This PCI device has failed 3 times in the last hour: It was caused because the PCI state was not being saved after the first restore. Therefore, at the second recovery the PCI state would not be restored. Signed-off-by: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com> Signed-off-by: Breno Leitao <brenohl@br.ibm.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03serial: amba-pl011: lock console writes against interruptsRabin Vincent
commit ef605fdb33883d687cff5ba75095a91b313b4966 upstream. Protect against pl011_console_write() and the interrupt for the console UART running concurrently on different CPUs. Otherwise the console_write could spin for a long time waiting for the UART to become not busy, while the other CPU continuously services UART interrupts and keeps the UART busy. The checks for sysrq and oops_in_progress are taken from 8250.c. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Reviewed-by: Bibek Basu <bibek.basu@stericsson.com> Reviewed-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03TTY: fix UV serial console regressionJiri Slaby
commit 0eee50af5b13e00b3fb7a5fe8480419a71b8235d upstream. Commit 74c2107759d (serial: Use block_til_ready helper) and its fixup 3f582b8c110 (serial: fix termios settings in open) introduced a regression on UV systems. The serial eventually freezes while being used. It's completely unpredictable and sometimes needs a heap of traffic to happen first. To reproduce this, yast installation was used as it turned out to be pretty reliable in reproducing. Especially during installation process where one doesn't have an SSH daemon running. And no monitor as the HW is completely headless. So this was fun to find. Given the machine doesn't boot on vanilla before 2.6.36 final. (And the commits above are older.) Unless there is some bad race in the code, the hardware seems to be pretty broken. Otherwise pure MSR read should not cause such a bug, or? So to prevent the bug, revert to the old behavior. I.e. read modem status only if we really have to -- for non-CLOCAL set serials. Non-CLOCAL works on this hardware OK, I tried. See? I don't. And document that shit. Signed-off-by: Jiri Slaby <jslaby@suse.cz> References: https://lkml.org/lkml/2011/12/6/573 References: https://bugzilla.novell.com/show_bug.cgi?id=718518 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-12atmel_serial: fix spinlock lockup in RS485 codeClaudio Scordino
commit dbf1115d3f8c7052788aa4e6e46abd27f3b3eeba upstream. Patch to fix a spinlock lockup in the driver that sometimes happens when the tasklet starts. Signed-off-by: Claudio Scordino <claudio@evidence.eu.com> Signed-off-by: Dave Bender <codehero@gmail.com> Tested-by: Dave Bender <codehero@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-21Merge branch 'tty-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty * 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: TTY: ldisc, wait for ldisc infinitely in hangup TTY: ldisc, move wait idle to caller TTY: ldisc, allow waiting for ldisc arbitrarily long Revert "tty/serial: Prevent drop of DCD on suspend for Tegra UARTs" RS485: fix inconsistencies in the meaning of some variables pch_uart: Fix DMA resource leak issue serial,mfd: Fix CMSPAR setup tty/serial: Prevent drop of DCD on suspend for Tegra UARTs pch_uart: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor pch_uart: Support new device LAPIS Semiconductor ML7831 IOH pch_uart: Fix hw-flow control issue tty: hvc_dcc: Fix duplicate character inputs jsm: Change maintainership
2011-11-17TTY: ldisc, wait for ldisc infinitely in hangupJiri Slaby
For /dev/console case, we do not kill all ldisc users. It's due to redirected_tty_write test in __tty_hangup. In that case there still might be a process waiting e.g. in n_tty_read for input. We wait for such processes to disappear. The problem is that we use a timeout. After this timeout, we continue closing the ldisc and start freeing tty resources. It obviously leads to crashes when the other process is woken. So to fix this, we wait infinitely before reiniting the ldisc. (The tiocsetd remains untouched -- times out after 5s.) This is nicely reproducible with this run from shell: exec 0<>/dev/console 1<>/dev/console 2<>/dev/console and stopping a getty like: systemctl stop serial-getty@ttyS0.service The crash proper may be produced only under load or with constified timing the same as for 92f6fa09b. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Dave Young <hidave.darkstar@gmail.com> Cc: Dave Jones <davej@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Dmitriy Matrosov <sgf.dma@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-17TTY: ldisc, move wait idle to callerJiri Slaby
It is the only place where reinit is called from. And we really need to wait for the old ldisc to go once. Actually this is the place where the waiting originally was (before removed and re-added later). This will make the fix in the following patch easier to implement. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Dave Young <hidave.darkstar@gmail.com> Cc: Dave Jones <davej@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Dmitriy Matrosov <sgf.dma@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-17TTY: ldisc, allow waiting for ldisc arbitrarily longJiri Slaby
To fix a nasty bug in ldisc hup vs. reinit we need to wait infinitely long for ldisc to be gone. So here we add a parameter to tty_ldisc_wait_idle to allow that. This is only a preparation for the real fix which is done in the following patches. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Dave Young <hidave.darkstar@gmail.com> Cc: Dave Jones <davej@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Dmitriy Matrosov <sgf.dma@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15Revert "tty/serial: Prevent drop of DCD on suspend for Tegra UARTs"Greg Kroah-Hartman
This reverts commit 9636b755da7b498094bdf15b4ce9f6fd16995e4e. It wasn't supposed to be applied, thanks to Doug for letting me know. Cc: Doug Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15RS485: fix inconsistencies in the meaning of some variablesClaudio Scordino
The crisv10.c and the atmel_serial.c serial drivers intepret the fields of the serial_rs485 structure in a different way. In particular, crisv10.c uses SER_RS485_RTS_AFTER_SEND and SER_RS485_RTS_ON_SEND for the voltage of the RTS pin; atmel_serial.c, instead, uses these values to know if a delay must be set before and after sending. This patch makes the usage of these variables consistent across all drivers and fixes the Documentation as well. From now on, SER_RS485_RTS_AFTER_SEND and SER_RS485_RTS_ON_SEND will be used to set the voltage of the RTS pin (as in the crisv10.c driver); the delay will be understood by looking only at the value of delay_rts_before_send and delay_rts_after_send. Signed-off-by: Claudio Scordino <claudio@evidence.eu.com> Signed-off-by: Darron Black <darron@griffin.net> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15pch_uart: Fix DMA resource leak issueTomoya MORINAGA
Changing UART mode PIO->DMA->PIO->DMA like below, pch_uart driver can't get DMA channel resource. setserial /dev/ttyPCH0 ^low_latency setserial /dev/ttyPCH0 low_latency CAUSE: Changing mode using setserial command, ".startup" function which gets DMA channel is called before ".verify_port" function which sets dma-flag(use_dma/use_dma_flag) as 1. PIO->DMA .startup: Since dma-flag is 0, DMA channel is not requested. .verify_port: dma-flag is set as 1. .shutdown: N/A DMA->PIO .startup: Since dma-flag is 1, DMA channel is requested. .verify_port: dma-flag is set as 0. .shutdown: Since dma-flag is 0, DMA channel is not released. This means DMA channel resource leak occurs. Next time, this driver can't get DMA channel resource forever. MODIFICATION: Currently, when release DMA channel resource, this driver checks dma-flag. However, this specification occurs the above issue. This driver must check whether dma_request_channel is executed or not. The values are saved in private data variable "chan_tx/chan_tx". These variables mean if the value is NULL, DMA channel is not requested, if not NULL, DMA channel is requested. This patch fixes the issue. Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15serial,mfd: Fix CMSPAR setupAlan Cox
This is referenced the wrong way. Mika Westerberg added some checks to the tty to support multiple console, but the real problem is simply referencing the termios object via the wrong path. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15tty/serial: Prevent drop of DCD on suspend for Tegra UARTsDoug Anderson
On Tegra UARTs (except UART1), the DTR / DCD / DSR lines are not externally accessible. Instead, the DTR line internally appears to be looped back to be the input to the DCD and DSR lines. The net effect of this is that when we drop DTR (like when we suspend), we'll see DCD drop too. ...and when we see DCD drop, we treat that as a hangup. In order to prevent this hangup from occurring at every sleep, we need to force DTR to remain high on Tegra UARTs. This patch uses the mcr_mask / mcr_force fields, which were originally added for the kludge ALPHA_KLUDGE_MCR. Using these fields does not prevent us from removing ALPHA_KLUDGE_MCR--we can just remove the "if" tests I have added and always init mcr_mask / mcr_force from the serial8250_config. NOTE: If we have people that are using UARTA on a Tegra and need to control DTR, we'll need to either add a separate port type for UARTA or we'll need to add some tegra-specific code to detect whether the DTR needs to be left high. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15pch_uart: Change company name OKI SEMICONDUCTOR to LAPIS SemiconductorTomoya MORINAGA
On October 1 in 2011, OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15pch_uart: Support new device LAPIS Semiconductor ML7831 IOHTomoya MORINAGA
ML7831 is companion chip for Intel Atom E6xx series. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Acked-by: Alan Cox <alan@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15pch_uart: Fix hw-flow control issueTomoya MORINAGA
Using hardware flow control, currently, register of the control-bit(AFE) is not set. This patch fixes the issue. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Acked-by: Alan Cox <alan@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.0.4) at 2026-03-07 22:17:54 +0000