| Age | Commit message (Collapse) | Author |
|---|
|
This is the 6.1.141 stable release
Conflicts:
drivers/spi/spi-cadence-quadspi.c
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
This is the 6.1.134 stable release
Conflicts:
drivers/gpu/drm/tidss/tidss_dispc.c
drivers/media/v4l2-core/v4l2-mc.c
drivers/net/ethernet/ti/am65-cpsw-nuss.c
drivers/net/ethernet/ti/am65-cpts.c
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
commit 8614ecdb1570e4fffe87ebdc62b613ed66f1f6a6 upstream.
The controllers with rtl version larger than
RTL_REVISION_NEW_LPM (0x00002700) has bug which causes that controller
doesn't resume from L1 state. It happens if after receiving LPM packet
controller starts transitioning to L1 and in this moment the driver force
resuming by write operation to PORTSC.PLS.
It's corner case and happens when write operation to PORTSC occurs during
device delay before transitioning to L1 after transmitting ACK
time (TL1TokenRetry).
Forcing transition from L1->L0 by driver for revision larger than
RTL_REVISION_NEW_LPM is not needed, so driver can simply fix this issue
through block call of cdnsp_force_l0_go function.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538B55C3A6E71F9ED29E980DD842@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 241e2ce88e5a494be7a5d44c0697592f1632fbee upstream.
In very rare cases after resuming controller from L1 to L0 it reads
registers before the clock UTMI have been enabled and as the result
driver reads incorrect value.
Most of registers are in APB domain clock but some of them (e.g. PORTSC)
are in UTMI domain clock.
After entering to L1 state the UTMI clock can be disabled.
When controller transition from L1 to L0 the port status change event is
reported and in interrupt runtime function driver reads PORTSC.
During this read operation controller synchronize UTMI and APB domain
but UTMI clock is still disabled and in result it reads 0xFFFFFFFF value.
To fix this issue driver increases APB timeout value.
The issue is platform specific and if the default value of APB timeout
is not sufficient then this time should be set Individually for each
platform.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953846C57973E4DB134CAA71DDBF2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1059896f2bfdcebcdc7153c3be2307ea319501f upstream.
The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit
58f2fcb3a845 ("usb: cdnsp: Fix deadlock issue during using NCM gadget").
Under PREEMPT_RT the deadlock can be readily triggered by heavy network
traffic, for example using "iperf --bidir" over NCM ethernet link.
The deadlock occurs because the threaded interrupt handler gets
preempted by a softirq, but both are protected by the same spinlock.
Prevent deadlock by disabling softirq during threaded irq handler.
Cc: stable <stable@kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250318-rfs-cdns3-deadlock-v2-1-bfd9cfcee732@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0aca19e4037a4143273e90f1b44666b78b4dde9b ]
Some platforms (e.g. ti,j721e-usb, ti,am64-usb) require
this bit to be set to workaround a lockup issue with PHY
short suspend intervals [1]. Add a platform quirk flag
to indicate if Suspend Residency should be enabled.
[1] - https://www.ti.com/lit/er/sprz457h/sprz457h.pdf
i2409 - USB: USB2 PHY locks up due to short suspend
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240516044537.16801-2-r-gunasekaran@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-6.1.y-cicd
* 'linux-6.1.y' of git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (1362 commits)
Linux 6.1.119
net: Make copy_safe_from_sockptr() match documentation
char: xillybus: Fix trivial bug with mutex
parisc: fix a possible DMA corruption
null_blk: Fix return value of nullb_device_power_store()
null_blk: fix null-ptr-dereference while configuring 'power' and 'submit_queues'
null_blk: Remove usage of the deprecated ida_simple_xx() API
char: xillybus: Prevent use-after-free due to race condition
drm/amd: check num of link levels when update pcie param
mm: resolve faulty mmap_region() error path behaviour
mm: refactor arch_calc_vm_flag_bits() and arm64 MTE handling
mm: unconditionally close VMAs on error
mm: avoid unsafe VMA hook invocation when error arises on mmap hook
mm: revert "mm: shmem: fix data-race in shmem_getattr()"
net: fec: remove .ndo_poll_controller to avoid deadlocks
net/sched: taprio: extend minimum interval restriction to entire cycle too
ipvs: properly dereference pe in ip_vs_add_service
fs/9p: fix uninitialized values during inode evict
nfc: llcp: fix nfc_llcp_setsockopt() unsafe copies
net: add copy_safe_from_sockptr() helper
...
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-6.1.y-cicd
This is the 6.1.112 stable release
* tag 'v6.1.112' of git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (862 commits)
Linux 6.1.112
USB: usbtmc: prevent kernel-usb-infoleak
USB: serial: pl2303: add device id for Macrosilicon MS3020
x86/mm: Switch to new Intel CPU model defines
powercap: RAPL: fix invalid initialization for pl4_supported field
btrfs: calculate the right space for delayed refs when updating global reserve
selftests: mptcp: join: restrict fullmesh endp on 1st sf
can: mcp251xfd: move mcp251xfd_timestamp_start()/stop() into mcp251xfd_chip_start/stop()
can: mcp251xfd: properly indent labels
gpio: prevent potential speculation leaks in gpio_device_get_desc()
gpiolib: cdev: Ignore reconfiguration without direction
Revert "wifi: cfg80211: check wiphy mutex is held for wdev mutex"
netfilter: nf_tables: missing iterator type in lookup walk
netfilter: nft_set_pipapo: walk over current view on netlink dump
netfilter: nft_socket: Fix a NULL vs IS_ERR() bug in nft_socket_cgroup_subtree_level()
netfilter: nft_socket: make cgroupsv2 matching work with namespaces
xfs: journal geometry is not properly bounds checked
xfs: set bnobt/cntbt numrecs correctly when formatting new AGs
xfs: fix reloading entire unlinked bucket lists
xfs: make inode unlinked bucket recovery work with quotacheck
...
Fix at merge
Conflicts:
drivers/pci/controller/dwc/pci-keystone.c
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
|
|
[ Upstream commit e5fa8db0be3e8757e8641600c518425a4589b85c ]
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1702bec4477cc7d31adb4a760d14d33fac928b7a upstream.
Fix changes incorrect usb_request->status returned during disabling
endpoints. Before fix the status returned during dequeuing requests
while disabling endpoint was ECONNRESET.
Patch change it to ESHUTDOWN.
Patch fixes issue detected during testing UVC gadget.
During stopping streaming the class starts dequeuing usb requests and
controller driver returns the -ECONNRESET status. After completion
requests the class or application "uvc-gadget" try to queue this
request again. Changing this status to ESHUTDOWN cause that UVC assumes
that endpoint is disabled, or device is disconnected and stops
re-queuing usb requests.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538E8CA7A2096AAF6A3718FDD9E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 740f2e2791b98e47288b3814c83a3f566518fed2 upstream.
Stop Endpoint command on LINK TRB with TC bit set to 1 causes that
internal cycle bit can have incorrect state after command complete.
In consequence empty transfer ring can be incorrectly detected
when EP is resumed.
NOP TRB before LINK TRB avoid such scenario. Stop Endpoint command
is then on NOP TRB and internal cycle bit is not changed and have
correct value.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953878279F375CCCE6C6F40FDD8E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0497a356d3c498221eb0c1edc1e8985816092f12 upstream.
Patch fixes the incorrect "stream_id" table index instead of
"ep_index" used in cdnsp_get_hw_deq function.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB95381F2182688811D5C711CEDD8D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-6.1.y-cicd
This is the 6.1.80 stable release
* tag 'v6.1.80' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (195 commits)
Linux 6.1.80
fs/ntfs3: Enhance the attribute size check
arp: Prevent overflow in arp_req_get().
ahci: Extend ASM1061 43-bit DMA address quirk to other ASM106x parts
ata: ahci: add identifiers for ASM2116 series adapters
mptcp: add needs_id for netlink appending addr
mptcp: userspace pm send RM_ADDR for ID 0
mm: zswap: fix missing folio cleanup in writeback race path
fs/aio: Restrict kiocb_set_cancel_fn() to I/O submitted via libaio
mm/damon/reclaim: fix quota stauts loss due to online tunings
erofs: fix inconsistent per-file compression format
erofs: simplify compression configuration parser
i2c: imx: when being a target, mark the last read as processed
drm/amd/display: Fix memory leak in dm_sw_fini()
drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set
net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHY
Fix write to cloned skb in ipv6_hop_ioam()
phonet/pep: fix racy skb_queue_empty() use
phonet: take correct lock to peek at the RX queue
net: sparx5: Add spinlock for frame transmission from CPU
...
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
commit 5fd9e45f1ebcd57181358af28506e8a661a260b3 upstream.
829 if (request->complete) {
830 spin_unlock(&priv_dev->lock);
831 usb_gadget_giveback_request(&priv_ep->endpoint,
832 request);
833 spin_lock(&priv_dev->lock);
834 }
835
836 if (request->buf == priv_dev->zlp_buf)
837 cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
Driver append an additional zero packet request when queue a packet, which
length mod max packet size is 0. When transfer complete, run to line 831,
usb_gadget_giveback_request() will free this requestion. 836 condition is
true, so cdns3_gadget_ep_free_request() free this request again.
Log:
[ 1920.140696][ T150] BUG: KFENCE: use-after-free read in cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.140696][ T150]
[ 1920.151837][ T150] Use-after-free read at 0x000000003d1cd10b (in kfence-#36):
[ 1920.159082][ T150] cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.164988][ T150] cdns3_transfer_completed+0x438/0x5f8 [cdns3]
Add check at line 829, skip call usb_gadget_giveback_request() if it is
additional zero length packet request. Needn't call
usb_gadget_giveback_request() because it is allocated in this driver.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240202154217.661867-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd45f99034b0c8c9cb346dd0d6407a95ca3d36f6 upstream.
...
cdns3_gadget_ep_free_request(&priv_ep->endpoint, &priv_req->request);
list_del_init(&priv_req->list);
...
'priv_req' actually free at cdns3_gadget_ep_free_request(). But
list_del_init() use priv_req->list after it.
[ 1542.642868][ T534] BUG: KFENCE: use-after-free read in __list_del_entry_valid+0x10/0xd4
[ 1542.642868][ T534]
[ 1542.653162][ T534] Use-after-free read at 0x000000009ed0ba99 (in kfence-#3):
[ 1542.660311][ T534] __list_del_entry_valid+0x10/0xd4
[ 1542.665375][ T534] cdns3_gadget_ep_disable+0x1f8/0x388 [cdns3]
[ 1542.671571][ T534] usb_ep_disable+0x44/0xe4
[ 1542.675948][ T534] ffs_func_eps_disable+0x64/0xc8
[ 1542.680839][ T534] ffs_func_set_alt+0x74/0x368
[ 1542.685478][ T534] ffs_func_disable+0x18/0x28
Move list_del_init() before cdns3_gadget_ep_free_request() to resolve this
problem.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240202154217.661867-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47625b018c6bc788bc10dd654c82696eb0a5ef11 upstream.
Cadence have several controllers from 0x000403xx family but current
driver suuport detecting only one with DID equal 0x0004034E.
It causes that if someone uses different CDNSP controller then driver
will use incorrect version and register space.
Patch fix this issue.
cc: stable@vger.kernel.org
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240215121609.259772-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18a6be674306c9acb05c08e5c3fd376ef50a917c upstream.
host.c file has some parts of code that were introduced for CDNS3 driver
and should not be used with CDNSP driver.
This patch blocks using these parts of codes by CDNSP driver.
These elements include:
- xhci_plat_cdns3_xhci object
- cdns3 specific XECP_PORT_CAP_REG register
- cdns3 specific XECP_AUX_CTRL_REG1 register
cc: stable@vger.kernel.org
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240206104018.48272-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-6.1.y-cicd
This is the 6.1.79 stable release
* tag 'v6.1.79' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (1573 commits)
Linux 6.1.79
mlxsw: spectrum_acl_tcam: Fix stack corruption
fs/ntfs3: Add null pointer checks
arm64: Subscribe Microsoft Azure Cobalt 100 to ARM Neoverse N2 errata
dm: limit the number of targets and parameter size area
nilfs2: replace WARN_ONs for invalid DAT metadata block requests
nilfs2: fix potential bug in end_buffer_async_write
of: property: Add in-ports/out-ports support to of_graph_get_port_parent()
sched/membarrier: reduce the ability to hammer on sys_membarrier
kbuild: Drop -Wdeclaration-after-statement
locking: Introduce __cleanup() based infrastructure
apparmor: Free up __cleanup() name
dmaengine: ioat: Free up __cleanup() name
userfaultfd: fix mmap_changing checking in mfill_atomic_hugetlb
bpf: Remove trace_printk_lock
bpf: Do cleanup in bpf_bprintf_cleanup only when needed
bpf: Add struct for bin_args arg in bpf_bprintf_prepare
net: prevent mss overflow in skb_segment()
smb: client: fix parsing of SMB3.1.1 POSIX create context
smb: client: fix potential OOBs in smb2_parse_contexts()
...
|
|
TI USB2 PHY is known to have a lockup issue on very short
suspend intervals. Enable the Suspend Residency quirk flag to
workaround this as described in Errata i2409 [1].
[1] - https://www.ti.com/lit/er/sprz457h/sprz457h.pdf
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Some platforms (e.g. ti,j721e-usb, ti,am64-usb) require
this bit to be set to workaround a lockup issue with PHY
short suspend intervals [1]. Add a platform quirk flag
to indicate if Suspend Residency should be enabled.
[1] - https://www.ti.com/lit/er/sprz457h/sprz457h.pdf
i2409 - USB: USB2 PHY locks up due to short suspend
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
commit 40c304109e866a7dc123661a5c8ca72f6b5e14e0 upstream.
Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.
Data pattern likes below when sg enabled, package size is 1k and mult is 2
[UVC Header(8B) ] [data(3k - 8)] ...
The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
0xd000: wrong
0xe000: wrong
0xf000: correct
0x10000: wrong
0x11000: wrong
0x12000: correct
...
To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 92f02efa1d86d7dcaef7f38a5fe3396c4e88a93c upstream.
ISO basic transfer is
ITP(SOF) Package_0 Package_1 ... Package_n
CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.
According USB spec defination:
Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)
Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.
Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-3-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b8be5ecff26201bafb0a554c74e91571299fb94 upstream.
When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.
cdns3_prepare_trb: ep2in: trb 0000000000ac755f, dma buf: 0xbf455000, size: 8, burst: 128 ctrl: 0x00000415 (C=1, T=0, ISP, CHAIN, Normal)
cdns3_prepare_trb: ep2in: trb 00000000a574e693, dma buf: 0xc0200fe0, size: 1016, burst: 128 ctrl: 0x00000405 (C=1, T=0, ISP, Normal)
But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.
The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.
Fixed it by below major steps:
1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.
.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB, LINK_TRB ... LINK_TRB
^End of TRB List
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-6.1.y-cicd
This is the 6.1.67 stable release
* tag 'v6.1.67' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (3167 commits)
Linux 6.1.67
Revert "wifi: cfg80211: fix CQM for non-range use"
Linux 6.1.66
iomap: update ki_pos a little later in iomap_dio_complete
x86/apic/msi: Fix misconfigured non-maskable MSI quirk
x86/xen: fix percpu vcpu_info allocation
xen: simplify evtchn_do_upcall() call maze
xen: Allow platform PCI interrupt to be shared
r8169: fix deadlock on RTL8125 in jumbo mtu mode
r8169: disable ASPM in case of tx timeout
drm/amd/display: Fix MPCC 1DLUT programming
drm/amd/display: Fix the delta clamping for shaper LUT
drm/amd/display: clean code-style issues in dcn30_set_mpc_shaper_3dlut
drm/amd/display: Expand kernel doc for DC
mmc: sdhci-sprd: Fix vqmmc not shutting down after the card was pulled
mmc: core: add helpers mmc_regulator_enable/disable_vqmmc
drm/amd/pm: fix a memleak in aldebaran_tables_init
iommu/vt-d: Make context clearing consistent with context mapping
iommu/vt-d: Disable PCI ATS in legacy passthrough mode
iommu/vt-d: Add device_block_translation() helper
...
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
commit 58f2fcb3a845fcbbad2f3196bb37d744e0506250 upstream.
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
cc: stable@vger.kernel.org
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231108093125.224963-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34f08eb0ba6e4869bbfb682bf3d7d0494ffd2f87 upstream.
Gadget ACM while unloading module try to dequeue not queued usb
request which causes the kernel to crash.
Patch adds extra condition to check whether usb request is processed
by CDNSP driver.
cc: stable@vger.kernel.org
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230713081429.326660-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_PM_SLEEP is disabled
commit 9f35d612da5592f1bf1cae44ec1e023df37bea12 upstream.
The return type of cdns_set_active () is inconsistent
depending on whether CONFIG_PM_SLEEP is enabled, so the
return value is modified to void type.
Reported-by: Pavel Machek <pavel@denx.de>
Closes: https://lore.kernel.org/all/ZP7lIKUzD68XA91j@duo.ucw.cz/
Fixes: 2319b9c87fe2 ("usb: cdns3: Put the cdns set active part outside the spin lock")
Cc: stable@vger.kernel.org
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230926075333.1791011-1-xiaolei.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2319b9c87fe243327285f2fefd7374ffd75a65fc ]
The device may be scheduled during the resume process,
so this cannot appear in atomic operations. Since
pm_runtime_set_active will resume suppliers, put set
active outside the spin lock, which is only used to
protect the struct cdns data structure, otherwise the
kernel will report the following warning:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1163
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 651, name: sh
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
CPU: 0 PID: 651 Comm: sh Tainted: G WC 6.1.20 #1
Hardware name: Freescale i.MX8QM MEK (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x64/0x80
dump_stack+0x1c/0x38
__might_resched+0x1fc/0x240
__might_sleep+0x68/0xc0
__pm_runtime_resume+0x9c/0xe0
rpm_get_suppliers+0x68/0x1b0
__pm_runtime_set_status+0x298/0x560
cdns_resume+0xb0/0x1c0
cdns3_controller_resume.isra.0+0x1e0/0x250
cdns3_plat_resume+0x28/0x40
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230616021952.1025854-1-xiaolei.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-6.1.y-cicd
This is the 6.1.46 stable release
* tag 'v6.1.46' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (1543 commits)
Linux 6.1.46
drm/amd/pm/smu7: move variables to where they are used
sch_netem: fix issues in netem_change() vs get_dist_table()
alpha: remove __init annotation from exported page_is_ram()
ACPI: scan: Create platform device for CS35L56
platform/x86: serial-multi-instantiate: Auto detect IRQ resource for CSC3551
scsi: qedf: Fix firmware halt over suspend and resume
scsi: qedi: Fix firmware halt over suspend and resume
scsi: fnic: Replace return codes in fnic_clean_pending_aborts()
scsi: core: Fix possible memory leak if device_add() fails
scsi: snic: Fix possible memory leak if device_add() fails
scsi: 53c700: Check that command slot is not NULL
scsi: ufs: renesas: Fix private allocation
scsi: storvsc: Fix handling of virtual Fibre Channel timeouts
scsi: core: Fix legacy /proc parsing buffer overflow
netfilter: nf_tables: report use refcount overflow
nvme-rdma: fix potential unbalanced freeze & unfreeze
nvme-tcp: fix potential unbalanced freeze & unfreeze
btrfs: set cache_block_group_error if we find an error
btrfs: reject invalid reloc tree root keys with stack dump
...
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
commit 2627335a1329a0d39d8d277994678571c4f21800 upstream.
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
detection"
[ Upstream commit df49f2a0ac4a34c0cb4b5c233fcfa0add644c43c ]
This reverts commit edd60d24bd858cef165274e4cd6cab43bdc58d15.
Heikki reports that this should not be a global flag just to work around
one broken driver and should be fixed differently, so revert it.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: edd60d24bd85 ("usb: common: usb-conn-gpio: Set last role to unknown before initial detection")
Link: https://lore.kernel.org/r/ZImE4L3YgABnCIsP@kuha.fi.intel.com
Cc: Prashanth K <quic_prashk@quicinc.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit edd60d24bd858cef165274e4cd6cab43bdc58d15 ]
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() since last_role is same as
current role. This happens because during probe last_role gets
initialised to zero.
To avoid this, added a new constant in enum usb_role, last_role
is set to USB_ROLE_UNKNOWN before performing initial detection.
While at it, also handle default case for the usb_role switch
in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid
build warnings.
Fixes: 4602f3bff266 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit dce49449e04f ("usb: cdns3: allocate TX FIFO size according to
composite EP number") changed the ep_buf_size from a default value of
4 and introduced a mechanism to calculate the buffer size based on the
IN EPs per configuration. This calculation is carried out only for the
gadgets created using configfs and breaks for legacy gadget drivers
for CDNS3 UDC.
So start the UDC driver with the previously known safe ep_buf_size,
so that it works for gadget driver that don't invoke usb_gadget_check_config().
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
commit dbe678f6192f27879ac9ff6bc7a1036aad85aae9 upstream.
At iMX8QM platform, enable NCM gadget and run 'iperf3 -s'.
At host, run 'iperf3 -V -c fe80::6863:98ff:feef:3e0%enxc6e147509498'
[ 5] 0.00-1.00 sec 1.55 MBytes 13.0 Mbits/sec 90 4.18 KBytes
[ 5] 1.00-2.00 sec 1.44 MBytes 12.0 Mbits/sec 75 4.18 KBytes
[ 5] 2.00-3.00 sec 1.48 MBytes 12.4 Mbits/sec 75 4.18 KBytes
Expected speed should be bigger than 300Mbits/sec.
The root cause of this performance drop was found to be data corruption
happening at 4K borders in some Ethernet packets, leading to TCP
checksum errors. This corruption occurs from the position
(4K - (address & 0x7F)) to 4K. The u_ether function's allocation of
skb_buff reserves 64B, meaning all RX addresses resemble 0xXXXX0040.
Force trb_burst_size to 16 can fix this problem.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230518154946.3666662-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1edf48991a783d00a3a18dc0d27c88139e4030a2 upstream.
The patch 5bc38d33a5a1: "usb: cdnsp: Fixes issue with redundant
Status Stage" leads to the following Smatch static checker warning:
drivers/usb/cdns3/cdnsp-ep0.c:470 cdnsp_setup_analyze()
error: uninitialized symbol 'len'.
cc: <stable@vger.kernel.org>
Fixes: 5bc38d33a5a1 ("usb: cdnsp: Fixes issue with redundant Status Stage")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20230331090600.454674-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96b96b2a567fb34dd41c87e6cf01f6902ce8cae4 upstream.
Patch changes CDNS_DEVICE_ID in USBSSP PCI Glue driver to remove
the conflict with Cadence USBSS driver.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20230309063048.299378-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bc38d33a5a1209fd4de65101d1ae8255ea12c6e upstream.
In some cases, driver trees to send Status Stage twice.
The first one from upper layer of gadget usb subsystem and
second time from controller driver.
This patch fixes this issue and remove tricky handling of
SET_INTERFACE from controller driver which is no longer
needed.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20230307111420.376056-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1272fd652a226ccb34e9f47371b6121948048438 upstream.
PCI based platform can have more than two PCI functions.
USBSS PCI Glue driver during initialization should
consider only DRD/HOST/DEVICE PCI functions and
all other should be ignored. This patch adds additional
condition which causes that only DRD and HOST/DEVICE
function will be accepted.
cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20230308124427.311245-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1301c7b9f7efad2f11ef924e317c18ebd714fc9a upstream.
After doorbell DMA fetches the TRB. If during dequeuing request
driver changes NORMAL TRB to LINK TRB but doesn't delete it from
controller cache then controller will handle cached TRB and packet
can be lost.
The example scenario for this issue looks like:
1. queue request - set doorbell
2. dequeue request
3. send OUT data packet from host
4. Device will accept this packet which is unexpected
5. queue new request - set doorbell
6. Device lost the expected packet.
By setting DFLUSH controller clears DRDY bit and stop DMA transfer.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20221115100039.441295-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae423ef5d095e09970f52c08020fdbf7f9d87c22 upstream.
Patch implements the handling of ZLP for control transfer.
To send the ZLP driver must prepare the extra TRB in TD with
length set to zero and TRB type to TRB_NORMAL.
The first TRB must have set TRB_CHAIN flag, TD_SIZE = 1
and TRB type to TRB_DATA.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20221122085138.332434-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch modifies the TD_SIZE in TRB before ZLP TRB.
The TD_SIZE in TRB before ZLP TRB must be set to 1 to force
processing ZLP TRB by controller.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20221115092218.421267-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During handling Clear Halt Endpoint Feature request, driver invokes
Reset Endpoint command. Because this command has some issue with
transition endpoint from Running to Idle state the driver must
stop the endpoint by using Stop Endpoint command.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20221110063005.370656-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When usb 3.0 hub connect with one USB 2.0 device and NO USB 3.0 device,
some usb hub reports endless port reset message.
[ 190.324169] usb 2-1: new SuperSpeed USB device number 88 using xhci-hcd
[ 190.352834] hub 2-1:1.0: USB hub found
[ 190.356995] hub 2-1:1.0: 4 ports detected
[ 190.700056] usb 2-1: USB disconnect, device number 88
[ 192.472139] usb 2-1: new SuperSpeed USB device number 89 using xhci-hcd
[ 192.500820] hub 2-1:1.0: USB hub found
[ 192.504977] hub 2-1:1.0: 4 ports detected
[ 192.852066] usb 2-1: USB disconnect, device number 89
The reason is the runtime pm state of USB2.0 port is active and
USB 3.0 port is suspend, so parent device is active state.
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb2/power/runtime_status
suspended
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb1/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/power/runtime_status
active
So xhci_cdns3_suspend_quirk() have not called. U3 configure is not applied.
move U3 configure into host start. Reinit again in resume function in case
controller power lost during suspend.
Cc: stable@vger.kernel.org 5.10
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221026190749.2280367-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Smatch reports the following error:
drivers/usb/cdns3/cdns3-plat.c:113 cdns3_plat_probe() warn:
platform_get_irq() does not return zero
From the document, platform_get_irq_byname_optional only returns
non-zero value, and negative value on failure.
Fix this by removing the zero value checking.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220926135922.24541-1-dzm91@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062137.5766-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The TRB_SMM flag indicates that DMA has completed the TD service with
this TRB. Usually it’s a last TRB in TD. In case of ISOC transfer for
bInterval > 1 each ISOC transfer contains more than one TD associated
with usb request (one TD per ITP). In such case the TRB_SMM flag will
be set in every TD and driver will recognize the end of transfer after
processing the first TD with TRB_SMM. In result driver stops updating
request->actual and returns incorrect actual length.
To fix this issue driver additionally must check TRB_CHAIN which is not
used for isochronous transfers.
Fixes: 249f0a25e8be ("usb: cdns3: gadget: handle sg list use case at completion correctly")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062207.5824-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clang warns:
drivers/usb/cdns3/cdns3-gadget.c:2290:11: error: variable 'priv_dev' is uninitialized when used here [-Werror,-Wuninitialized]
dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
^~~~~~~~
include/linux/dev_printk.h:155:18: note: expanded from macro 'dev_dbg'
dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~
include/linux/dynamic_debug.h:167:7: note: expanded from macro 'dynamic_dev_dbg'
dev, fmt, ##__VA_ARGS__)
^~~
include/linux/dynamic_debug.h:152:56: note: expanded from macro '_dynamic_func_call'
__dynamic_func_call(__UNIQUE_ID(ddebug), fmt, func, ##__VA_ARGS__)
^~~~~~~~~~~
include/linux/dynamic_debug.h:134:15: note: expanded from macro '__dynamic_func_call'
func(&id, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/usb/cdns3/cdns3-gadget.c:2278:31: note: initialize the variable 'priv_dev' to silence this warning
struct cdns3_device *priv_dev;
^
= NULL
1 error generated.
The priv_dev assignment was moved below the if statement to avoid
potentially dereferencing ep before it was checked but priv_dev is used
in the dev_dbg() call.
To fix this, move the priv_dev and comp_desc assignments back to their
original spot and hoist the ep check above those assignments with a call
to pr_debug() instead of dev_dbg().
Fixes: c3ffc9c4ca44 ("usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()")
Link: https://github.com/ClangBuiltLinux/linux/issues/1680
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
If 'ep' is NULL, result of ep_to_cdns3_ep(ep) is invalid pointer
and its dereference with priv_ep->cdns3_dev may cause panic.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Andrey Strachuk <strochuk@ispras.ru>
Link: https://lore.kernel.org/r/20220718160052.4188-1-strochuk@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Warning log:
[ 4.141392] Unexpected gfp: 0x4 (GFP_DMA32). Fixing up to gfp: 0xa20 (GFP_ATOMIC). Fix your code!
[ 4.150340] CPU: 1 PID: 175 Comm: 1-0050 Not tainted 5.15.5-00039-g2fd9ae1b568c #20
[ 4.158010] Hardware name: Freescale i.MX8QXP MEK (DT)
[ 4.163155] Call trace:
[ 4.165600] dump_backtrace+0x0/0x1b0
[ 4.169286] show_stack+0x18/0x68
[ 4.172611] dump_stack_lvl+0x68/0x84
[ 4.176286] dump_stack+0x18/0x34
[ 4.179613] kmalloc_fix_flags+0x60/0x88
[ 4.183550] new_slab+0x334/0x370
[ 4.186878] ___slab_alloc.part.108+0x4d4/0x748
[ 4.191419] __slab_alloc.isra.109+0x30/0x78
[ 4.195702] kmem_cache_alloc+0x40c/0x420
[ 4.199725] dma_pool_alloc+0xac/0x1f8
[ 4.203486] cdns3_allocate_trb_pool+0xb4/0xd0
pool_alloc_page(struct dma_pool *pool, gfp_t mem_flags)
{
...
page = kmalloc(sizeof(*page), mem_flags);
page->vaddr = dma_alloc_coherent(pool->dev, pool->allocation,
&page->dma, mem_flags);
...
}
kmalloc was called with mem_flags, which is passed down in
cdns3_allocate_trb_pool() and have GFP_DMA32 flags.
kmall_fix_flags() report warning.
GFP_DMA32 is not useful at all. dma_alloc_coherent() will handle
DMA memory region correctly by pool->dev. GFP_DMA32 can be removed
safely.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20220609154456.2871672-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
