| Age | Commit message (Collapse) | Author |
|---|
|
pxa27x disconnects pullups on suspend but doesn't
notify the gadget driver about it, so gadget driver
can't disable the endpoints it was using.
This causes problems on resume because gadget core
will think endpoints are still enabled and just
ignore the following usb_ep_enable().
Fix this problem by calling
gadget_driver->disconnect().
Cc: <stable@vger.kernel.org> # v3.10+
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
use safe copy_*_user instead of unsafe __copy_*_user
functions when accessing userland memory.
Signed-off-by: Daniel Walter <dwalter@sigma-star.at>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> #4.0+
Fixes: 9870d895ad87 ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The current code tries to allocate memory with GFP_KERNEL at
interrupt context, it would show below warning during the enumeration
when I test it with chipidea hardware, change GFP flag as GFP_ATOMIC
can fix this issue.
[ 40.438237] zero gadget: high-speed config #2: loopback
[ 40.444924] ------------[ cut here ]------------
[ 40.449609] WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x108/0x128()
[ 40.461715] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[ 40.467130] Modules linked in:
[ 40.470216] usb_f_ss_lb g_zero libcomposite evbug
[ 40.473822] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.3.0-rc5-00168-gb730aaf #604
[ 40.481496] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 40.487345] Backtrace:
[ 40.489857] [<80014e94>] (dump_backtrace) from [<80015088>] (show_stack+0x18/0x1c)
[ 40.497445] r6:80b67a80 r5:00000000 r4:00000000 r3:00000000
[ 40.503234] [<80015070>] (show_stack) from [<802e27b4>] (dump_stack+0x8c/0xa4)
[ 40.510503] [<802e2728>] (dump_stack) from [<8002cfe8>] (warn_slowpath_common+0x80/0xbc)
[ 40.518612] r6:8007510c r5:00000009 r4:80b49c88 r3:00000001
[ 40.524396] [<8002cf68>] (warn_slowpath_common) from [<8002d05c>] (warn_slowpath_fmt+0x38/0x40)
[ 40.533109] r8:bcfdef80 r7:bdb705cc r6:000080d0 r5:be001e80 r4:809cc278
[ 40.539965] [<8002d028>] (warn_slowpath_fmt) from [<8007510c>] (lockdep_trace_alloc+0x108/0x128)
[ 40.548766] r3:809d0128 r2:809cc278
[ 40.552401] r4:600b0193
[ 40.554990] [<80075004>] (lockdep_trace_alloc) from [<801093d4>] (kmem_cache_alloc+0x28/0x15c)
[ 40.563618] r4:000080d0 r3:80b4aa8c
[ 40.567270] [<801093ac>] (kmem_cache_alloc) from [<804d95e4>] (ep_alloc_request+0x58/0x68)
[ 40.575550] r10:7f01f104 r9:00000001 r8:bcfdef80 r7:bdb705cc r6:bc178700 r5:00000000
[ 40.583512] r4:bcfdef80 r3:813c0a38
[ 40.587183] [<804d958c>] (ep_alloc_request) from [<7f01f7ec>] (loopback_set_alt+0x114/0x21c [usb_f_ss_lb])
[ 40.596929] [<7f01f6d8>] (loopback_set_alt [usb_f_ss_lb]) from [<7f006910>] (composite_setup+0xbd0/0x17e8 [libcomposite])
[ 40.607902] r10:bd3a2c0c r9:00000000 r8:bcfdef80 r7:bc178700 r6:bdb702d0 r5:bcfdefdc
[ 40.615866] r4:7f0199b4 r3:00000002
[ 40.619542] [<7f005d40>] (composite_setup [libcomposite]) from [<804dae88>] (udc_irq+0x784/0xd1c)
[ 40.628431] r10:80bb5619 r9:c0876140 r8:00012001 r7:bdb71010 r6:bdb70568 r5:00010001
[ 40.636392] r4:bdb70014
[ 40.638985] [<804da704>] (udc_irq) from [<804d64f8>] (ci_irq+0x5c/0x118)
[ 40.645702] r10:80bb5619 r9:be11e000 r8:00000117 r7:00000000 r6:bdb71010 r5:be11e060
[ 40.653666] r4:bdb70010
[ 40.656261] [<804d649c>] (ci_irq) from [<8007f638>] (handle_irq_event_percpu+0x7c/0x13c)
[ 40.664367] r6:00000000 r5:be11e060 r4:bdb05cc0 r3:804d649c
[ 40.670149] [<8007f5bc>] (handle_irq_event_percpu) from [<8007f740>] (handle_irq_event+0x48/0x6c)
[ 40.679036] r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:bdb05cc0 r5:be11e060
[ 40.686998] r4:be11e000
[ 40.689581] [<8007f6f8>] (handle_irq_event) from [<80082850>] (handle_fasteoi_irq+0xd4/0x1b0)
[ 40.698120] r6:80b56a30 r5:be11e060 r4:be11e000 r3:00000000
[ 40.703898] [<8008277c>] (handle_fasteoi_irq) from [<8007ec04>] (generic_handle_irq+0x28/0x3c)
[ 40.712524] r7:00000000 r6:80b4aaf4 r5:00000117 r4:80b445fc
[ 40.718304] [<8007ebdc>] (generic_handle_irq) from [<8007ef20>] (__handle_domain_irq+0x6c/0xe8)
[ 40.727033] [<8007eeb4>] (__handle_domain_irq) from [<800095d4>] (gic_handle_irq+0x48/0x94)
[ 40.735402] r9:c080f100 r8:80b4ac6c r7:c080e100 r6:80b67d40 r5:80b49f00 r4:c080e10c
[ 40.743290] [<8000958c>] (gic_handle_irq) from [<80015d38>] (__irq_svc+0x58/0x78)
[ 40.750791] Exception stack(0x80b49f00 to 0x80b49f48)
[ 40.755873] 9f00: 00000001 00000001 00000000 80024320 80b48000 80b4a9d0 80b4a984 80b433e4
[ 40.764078] 9f20: 00000001 807f4680 00000000 80b49f5c 80b49f20 80b49f50 80071ca4 800113fc
[ 40.772272] 9f40: 200b0013 ffffffff
[ 40.775776] r9:807f4680 r8:00000001 r7:80b49f34 r6:ffffffff r5:200b0013 r4:800113fc
[ 40.783677] [<800113d4>] (arch_cpu_idle) from [<8006c5bc>] (default_idle_call+0x28/0x38)
[ 40.791798] [<8006c594>] (default_idle_call) from [<8006c6dc>] (cpu_startup_entry+0x110/0x1b0)
[ 40.800445] [<8006c5cc>] (cpu_startup_entry) from [<807e95dc>] (rest_init+0x12c/0x168)
[ 40.808376] r7:80b4a8c0 r3:807f4b7c
[ 40.812030] [<807e94b0>] (rest_init) from [<80ad7cc0>] (start_kernel+0x360/0x3d4)
[ 40.819528] r5:80bcb000 r4:80bcb050
[ 40.823171] [<80ad7960>] (start_kernel) from [<8000807c>] (0x8000807c)
It fixes commit 91c42b0da8e3 ("usb: gadget: loopback: Fix looping back
logic implementation").
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c2f ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f78
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
|
|
1. Rename dequeue_signal_lock() to kernel_dequeue_signal(). This
matches another "for kthreads only" kernel_sigaction() helper.
2. Remove the "tsk" and "mask" arguments, they are always current
and current->blocked. And it is simply wrong if tsk != current.
3. We could also remove the 3rd "siginfo_t *info" arg but it looks
potentially useful. However we can simplify the callers if we
change kernel_dequeue_signal() to accept info => NULL.
4. Remove _irqsave, it is never called from atomic context.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (148 commits)
tty: Use unbound workqueue for all input workers
tty: Abstract tty buffer work
tty: Prevent tty teardown during tty_write_message()
tty: core: Use correct spinlock flavor in tiocspgrp()
tty: Combine SIGTTOU/SIGTTIN handling
serial: amba-pl011: fix incorrect integer size in pl011_fifo_to_tty()
ttyFDC: Fix build problems due to use of module_{init,exit}
tty: remove unneeded return statement
serial: 8250_mid: add support for DMA engine handling from UART MMIO
dmaengine: hsu: remove platform data
dmaengine: hsu: introduce stubs for the exported functions
dmaengine: hsu: make the UART driver in control of selecting this driver
serial: fix mctrl helper functions
serial: 8250_pci: Intel MID UART support to its own driver
serial: fsl_lpuart: add earlycon support
tty: disable unbind for old 74xx based serial/mpsc console port
serial: pl011: Spelling s/clocks-names/clock-names/
n_tty: Remove reader wakeups for TTY_BREAK/TTY_PARITY chars
tty: synclink, fix indentation
serial: at91, fix rs485 properties
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.4 merge window
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Defect 7374 workaround enables all GPEP as endpoint 0. Restore
endpoint number when defect 7374 workaround is disabled. Otherwise,
check to match USB endpoint number to hardware endpoint number in
net2280_enable() fails.
Cc: <stable@vger.kernel.org> # 4.2
Reported-by: Paul Jones <p.jones@teclyn.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
s/regsiter/register/
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
close_wait is no longer needed or provided by the tty core.
Move close_wait to struct gs_port.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit e0857ce58e8658657f5f12fe25272b93cfeb16aa
("usb: gadget: loopback: don't queue requests to bogus endpoints")
Loopback function is not realy working as that commit removed
all looping back logic. After that commit ep-out works like
/dev/null and ep-in works like /dev/zero.
This commit fix this issue by allocating set of out requests
and set of in requests but each out req shares buffer with
one in req:
out_req->buf ---> buf <--- in_req.buf
out_req->context <---> in_req.context
The completion routine simply enqueue the suitable req in
an oposite direction.
Cc: <stable@vger.kernel.org> # 3.18+
Fixes: e0857ce58e8658657f5f12fe25272b93cfeb16aa
("usb: gadget: loopback: don't queue requests to bogus endpoints")
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Each instance of loopback function may have different qlen
and buflen attributes values. When linking function to
configuration those values had been assigned to global
variables. Linking other instance to config overwrites those
values.
This commit moves those values to f_loopback structure
to avoid overwriting. Now each function has its own instance
of those values.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Move function parameters to struct f_sourcesink to make them per instance
instead of having them as global variables. Since we can have multiple
instances of USB function we also want to have separate set of parameters
for each instance.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This also allows to remove the target-specific old configfs macros, and
gets rid of the target_core_fabric_configfs.h header which only had one
function declaration left that could be moved to a better place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
UVC is a little different from other configfs consumers in that it wants
different function and field names from the exposed attribute name, so
it keeps it's local macros to define attributes instead of using the common
ones.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When handling device GET_DESCRIPTOR, composite gadget driver fills
the bcdUSB field only if the gadget supports USB 3.0. Otherwise
the field is left unfilled.
For consistency, set bcdUSB to 0x0200 for gadgets that don't
support superspeed.
It's correct to use 0x0200 for any setting that doesn't use
superspeed, since USB 2.0 devices can restrict themselves to
full speed only. It is NOT correct to use 0x0210, since BOS
descriptors are handled only if gadget_is_superspeed() is
satisfied, otherwise it results in a stall.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Most of USB functions place new line after attribute value.
Let's follow this convention also in source sink function
as it improves readability.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Most of USB functions place new line after attribute value.
Let's follow this convention also in loopback function
as it improves readability.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
While building allmodconfig on avr32 the build failed with the error:
"at91_pmc_base" [drivers/usb/gadget/udc/atmel_usba_udc.ko] undefined!
On checking the code it turned out that if CONFIG_OF is defined then it
is using at91_pmc_read() which is using at91_pmc_base. And unless
COMMON_CLK_AT91 is defined we donot have at91_pmc_base. And
COMMON_CLK_AT91 is available with AT91 architecture.
Mention the dependency such that this driver builds with avr32 only if
OF is not enabled.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
A NULL comparison can be written as if (var) or if (!var).
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Rearrange the udc_basic_init function to remove the forward declaration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Remove the forward declarations of udc_pci_probe and udc_pci_remove.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Rearrange udc_free_dma_chain to remove the forward declaration. While at
it fixed all the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Rearrange udc_create_dma_chain to remove the forward declaration. While
rearranging fixed the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Rearrange the udc_remote_wakeup function to remove the forward
declaration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Rearrange the udc_probe function to remove the forward declarations.
While rearranging also fixed the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The condition checking for irq_registered, regs, mem_region and active
are not required as this is the remove function. And we are in the
remove means that probe was successful and they can never be NULL at
this point of code.
It was required in the original code as the remove function was part of
the error handler of probe function.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We have the function free_dma_pools() which frees all the dma pools. Use
it instead of calling all the functions separately. The if conditions
for data_requests and stp_requests are also not required here as this is
the remove function and we are here means probe has succeeded and dma
has been successfully allocated, so they cannot be NULL here.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use WARN_ON() instead of halting the kernel with BUG_ON() and also fix
the checkpatch warning.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Handle the error properly instead of calling the pci remove function.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
A rewrite of init_dma_pools() with proper error handling.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Make videobuf2-v4l2 as a wrapper of videobuf2-core for v4l2-use.
And replace videobuf2-core.h with videobuf2-v4l2.h.
This renaming change should be accompanied by the modifications
of all device drivers that include videobuf2-core.h.
It can be done with just running this shell script.
replace()
{
str1=$1
str2=$2
dir=$3
for file in $(find $dir -name *.h -o -name *.c -o -name Makefile)
do
echo $file
sed "s/$str1/$str2/g" $file > $file.out
mv $file.out $file
done
}
replace "videobuf2-core" "videobuf2-v4l2" "include/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/usb/gadget/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/staging/media/"
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
