summaryrefslogtreecommitdiff
path: root/drivers/usb/host/xhci.c
AgeCommit message (Collapse)Author
2021-05-22xhci: Do not use GFP_KERNEL in (potentially) atomic contextChristophe JAILLET
commit dda32c00c9a0fa103b5d54ef72c477b7aa993679 upstream. 'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be submitted in interrupt context" (see comment related to 'usb_submit_urb()' in 'drivers/usb/core/urb.c') So this flag should be used in all the calling chain. Up to now, 'xhci_check_maxpacket()' which is only called from 'xhci_urb_enqueue()', uses GFP_KERNEL. Be safe and pass the mem_flags to this function as well. Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring") Cc: <stable@vger.kernel.org> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com [iwamatsu: Adjust context] Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-17xhci: Improve detection of device initiated wake signal.Mathias Nyman
commit 253f588c70f66184b1f3a9bbb428b49bbda73e80 upstream. A xHC USB 3 port might miss the first wake signal from a USB 3 device if the port LFPS reveiver isn't enabled fast enough after xHC resume. xHC host will anyway be resumed by a PME# signal, but will go back to suspend if no port activity is seen. The device resends the U3 LFPS wake signal after a 100ms delay, but by then host is already suspended, starting all over from the beginning of this issue. USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device needs to delay 100ms before resending the wake. Don't suspend immediately if port activity isn't detected in resume. Instead add a retry. If there is no port activity then delay for 120ms, and re-check for port activity. Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-12USB: xhci: fix U1/U2 handling for hardware with XHCI_INTEL_HOST quirk setMichael Grzeschik
commit 5d5323a6f3625f101dbfa94ba3ef7706cce38760 upstream. The commit 0472bf06c6fd ("xhci: Prevent U1/U2 link pm states if exit latency is too long") was constraining the xhci code not to allow U1/U2 sleep states if the latency to wake up from the U-states reached the service interval of an periodic endpoint. This fix was not taking into account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time will be calculated and configured differently. It checks for u1_params.mel/u2_params.mel as a limit. But the code could decide to write another MEL into the hardware. This leads to broken cases where not enough bandwidth is available for other devices: usb 1-2: can't set config #1, error -28 This patch is fixing that case by checking for timeout_ns after the wakeup time was calculated depending on the quirks. Fixes: 0472bf06c6fd ("xhci: Prevent U1/U2 link pm states if exit latency is too long") Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-29xhci: Poll for U0 after disabling USB2 LPMKai-Heng Feng
[ Upstream commit b3d71abd135e6919ca0b6cab463738472653ddfb ] USB2 devices with LPM enabled may interrupt the system suspend: [ 932.510475] usb 1-7: usb suspend, wakeup 0 [ 932.510549] hub 1-0:1.0: hub_suspend [ 932.510581] usb usb1: bus suspend, wakeup 0 [ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended [ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended .. [ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03 .. [ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16 [ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16 [ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16 During system suspend, USB core will let HC suspends the device if it doesn't have remote wakeup enabled and doesn't have any children. However, from the log above we can see that the usb 1-7 doesn't get bus suspended due to not in U0. After a while the port finished U2 -> U0 transition, interrupts the suspend process. The observation is that after disabling LPM, port doesn't transit to U0 immediately and can linger in U2. xHCI spec 4.23.5.2 states that the maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for the affected device is advertised as 400us, which is still not enough based on my testing result. So let's use the maximum permitted latency, 10000, to poll for U0 status to solve the issue. Cc: stable@vger.kernel.org Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200624135949.22611-6-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-29xhci: Fix enumeration issue when setting max packet size for FS devices.Al Cooper
commit a73d9d9cfc3cfceabd91fb0b0c13e4062b6dbcd7 upstream. Unable to complete the enumeration of a USB TV Tuner device. Per XHCI spec (4.6.5), the EP state field of the input context shall be cleared for a set address command. In the special case of an FS device that has "MaxPacketSize0 = 8", the Linux XHCI driver does not do this before evaluating the context. With an XHCI controller that checks the EP state field for parameter context error this causes a problem in cases such as the device getting reset again after enumeration. When that field is cleared, the problem does not occur. This was found and fixed by Sasi Kumar. Cc: stable@vger.kernel.org Signed-off-by: Al Cooper <alcooperx@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200624135949.22611-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-21usb: xhci: only set D3hot for pci deviceHenry Lin
[ Upstream commit f2c710f7dca8457e88b4ac9de2060f011254f9dd ] Xhci driver cannot call pci_set_power_state() on non-pci xhci host controllers. For example, NVIDIA Tegra XHCI host controller which acts as platform device with XHCI_SPURIOUS_WAKEUP quirk set in some platform hits this issue during shutdown. Cc: <stable@vger.kernel.org> Fixes: 638298dc66ea ("xhci: Fix spurious wakeups after S5 on Haswell") Signed-off-by: Henry Lin <henryl@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-21xhci: Increase STS_HALT timeout in xhci_suspend()Kai-Heng Feng
commit 7c67cf6658cec70d8a43229f2ce74ca1443dc95e upstream. I've recently observed failed xHCI suspend attempt on AMD Raven Ridge system: kernel: xhci_hcd 0000:04:00.4: WARN: xHC CMD_RUN timeout kernel: PM: suspend_common(): xhci_pci_suspend+0x0/0xd0 returns -110 kernel: PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -110 kernel: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns -110 kernel: PM: Device 0000:04:00.4 failed to suspend async: error -110 Similar to commit ac343366846a ("xhci: Increase STS_SAVE timeout in xhci_suspend()") we also need to increase the HALT timeout to make it be able to suspend again. Cc: <stable@vger.kernel.org> # 5.2+ Fixes: f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-17xhci: Increase STS_SAVE timeout in xhci_suspend()Kai-Heng Feng
commit ac343366846a445bb81f0a0e8f16abb8bd5d5d88 upstream. After commit f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()"), ASMedia xHCI may fail to suspend. Although the algorithms are essentially the same, the old max timeout is (usec + usec * time of doing readl()), and the new max timeout is just usec, which is much less than the old one. Increase the timeout to make ASMedia xHCI able to suspend again. BugLink: https://bugs.launchpad.net/bugs/1844021 Fixes: f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()") Cc: <stable@vger.kernel.org> # v5.2+ Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-8-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-17usb: xhci: wait for CNR controller not ready bit in xhci resumeRick Tseng
commit a70bcbc322837eda1ab5994d12db941dc9733a7d upstream. NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold. Thus we need to wait for CNR bit to clear in xhci resume, just as in xhci init. [Minor changes to comment and commit message -Mathias] Cc: <stable@vger.kernel.org> Signed-off-by: Rick Tseng <rtseng@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-17xhci: Check all endpoints for LPM timeoutJan Schmidt
commit d500c63f80f2ea08ee300e57da5f2af1c13875f5 upstream. If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep checking further endpoints, as there might be periodic endpoints later that return USB3_LPM_DISABLED due to shorter service intervals. Without this, the code can set too high a maximum-exit-latency and prevent the use of multiple USB3 cameras that should be able to work. Cc: <stable@vger.kernel.org> Signed-off-by: Jan Schmidt <jan@centricular.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-17xhci: Prevent device initiated U1/U2 link pm if exit latency is too longMathias Nyman
commit cd9d9491e835a845c1a98b8471f88d26285e0bb9 upstream. If host/hub initiated link pm is prevented by a driver flag we still must ensure that periodic endpoints have longer service intervals than link pm exit latency before allowing device initiated link pm. Fix this by continue walking and checking endpoint service interval if xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED While at it fix the split line error message Tested-by: Jan Schmidt <jan@centricular.com> Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-11usb: xhci: avoid null pointer deref when bos field is NULLCarsten Schmid
commit 7aa1bb2ffd84d6b9b5f546b079bb15cd0ab6e76e upstream. With defective USB sticks we see the following error happen: usb 1-3: new high-speed USB device number 6 using xhci_hcd usb 1-3: device descriptor read/64, error -71 usb 1-3: device descriptor read/64, error -71 usb 1-3: new high-speed USB device number 7 using xhci_hcd usb 1-3: device descriptor read/64, error -71 usb 1-3: unable to get BOS descriptor set usb 1-3: New USB device found, idVendor=0781, idProduct=5581 usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 ... BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 This comes from the following place: [ 1660.215380] IP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] [ 1660.222092] PGD 0 P4D 0 [ 1660.224918] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 1660.425520] CPU: 1 PID: 38 Comm: kworker/1:1 Tainted: P U W O 4.14.67-apl #1 [ 1660.434277] Workqueue: usb_hub_wq hub_event [usbcore] [ 1660.439918] task: ffffa295b6ae4c80 task.stack: ffffad4580150000 [ 1660.446532] RIP: 0010:xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] [ 1660.453821] RSP: 0018:ffffad4580153c70 EFLAGS: 00010046 [ 1660.459655] RAX: 0000000000000000 RBX: ffffa295b4d7c000 RCX: 0000000000000002 [ 1660.467625] RDX: 0000000000000002 RSI: ffffffff984a55b2 RDI: ffffffff984a55b2 [ 1660.475586] RBP: ffffad4580153cc8 R08: 0000000000d6520a R09: 0000000000000001 [ 1660.483556] R10: ffffad4580a004a0 R11: 0000000000000286 R12: ffffa295b4d7c000 [ 1660.491525] R13: 0000000000010648 R14: ffffa295a84e1800 R15: 0000000000000000 [ 1660.499494] FS: 0000000000000000(0000) GS:ffffa295bfc80000(0000) knlGS:0000000000000000 [ 1660.508530] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1660.514947] CR2: 0000000000000008 CR3: 000000025a114000 CR4: 00000000003406a0 [ 1660.522917] Call Trace: [ 1660.525657] usb_set_usb2_hardware_lpm+0x3d/0x70 [usbcore] [ 1660.531792] usb_disable_device+0x242/0x260 [usbcore] [ 1660.537439] usb_disconnect+0xc1/0x2b0 [usbcore] [ 1660.542600] hub_event+0x596/0x18f0 [usbcore] [ 1660.547467] ? trace_preempt_on+0xdf/0x100 [ 1660.552040] ? process_one_work+0x1c1/0x410 [ 1660.556708] process_one_work+0x1d2/0x410 [ 1660.561184] ? preempt_count_add.part.3+0x21/0x60 [ 1660.566436] worker_thread+0x2d/0x3f0 [ 1660.570522] kthread+0x122/0x140 [ 1660.574123] ? process_one_work+0x410/0x410 [ 1660.578792] ? kthread_create_on_node+0x60/0x60 [ 1660.583849] ret_from_fork+0x3a/0x50 [ 1660.587839] Code: 00 49 89 c3 49 8b 84 24 50 16 00 00 8d 4a ff 48 8d 04 c8 48 89 ca 4c 8b 10 45 8b 6a 04 48 8b 00 48 89 45 c0 49 8b 86 80 03 00 00 <48> 8b 40 08 8b 40 03 0f 1f 44 00 00 45 85 ff 0f 84 81 01 00 00 [ 1660.608980] RIP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] RSP: ffffad4580153c70 [ 1660.617921] CR2: 0000000000000008 Tracking this down shows that udev->bos is NULL in the following code: (xhci.c, in xhci_set_usb2_hardware_lpm) field = le32_to_cpu(udev->bos->ext_cap->bmAttributes); <<<<<<< here xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n", enable ? "enable" : "disable", port_num + 1); if (enable) { /* Host supports BESL timeout instead of HIRD */ if (udev->usb2_hw_lpm_besl_capable) { /* if device doesn't have a preferred BESL value use a * default one which works with mixed HIRD and BESL * systems. See XHCI_DEFAULT_BESL definition in xhci.h */ if ((field & USB_BESL_SUPPORT) && (field & USB_BESL_BASELINE_VALID)) hird = USB_GET_BESL_BASELINE(field); else hird = udev->l1_params.besl; The failing case is when disabling LPM. So it is sufficient to avoid access to udev->bos by moving the instruction into the "enable" clause. Cc: Stable <stable@vger.kernel.org> Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-11xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()Andrey Smirnov
commit f7fac17ca925faa03fc5eb854c081a24075f8bad upstream. Xhci_handshake() implements the algorithm already captured by readl_poll_timeout_atomic(). Convert the former to use the latter to avoid repetition. Turned out this patch also fixes a bug on the AMD Stoneyridge platform where usleep(1) sometimes takes over 10ms. This means a 5 second timeout can easily take over 15 seconds which will trigger the watchdog and reboot the system. [Add info about patch fixing a bug to commit message -Mathias] Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Tested-by: Raul E Rangel <rrangel@chromium.org> Reviewed-by: Raul E Rangel <rrangel@chromium.org> Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-13xhci: Prevent U1/U2 link pm states if exit latency is too longMathias Nyman
commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream. Don't allow USB3 U1 or U2 if the latency to wake up from the U-state reaches the service interval for a periodic endpoint. This is according to xhci 1.1 specification section 4.23.5.2 extra note: "Software shall ensure that a device is prevented from entering a U-state where its worst case exit latency approaches the ESIT." Allowing too long exit latencies for periodic endpoint confuses xHC internal scheduling, and new devices may fail to enumerate with a "Not enough bandwidth for new device state" error from the host. Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-19xhci: Fix use-after-free in xhci_free_virt_deviceMathias Nyman
commit 44a182b9d17765514fa2b1cc911e4e65134eef93 upstream. KASAN found a use-after-free in xhci_free_virt_device+0x33b/0x38e where xhci_free_virt_device() sets slot id to 0 if udev exists: if (dev->udev && dev->udev->slot_id) dev->udev->slot_id = 0; dev->udev will be true even if udev is freed because dev->udev is not set to NULL. set dev->udev pointer to NULL in xhci_free_dev() The original patch went to stable so this fix needs to be applied there as well. Fixes: a400efe455f7 ("xhci: zero usb device slot_id member when disabling and freeing a xhci slot") Cc: <stable@vger.kernel.org> Reported-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-24usb: xhci: increase CRS timeout valueAjay Gupta
[ Upstream commit 305886ca87be480ae159908c2affd135c04215cf ] Some controllers take almost 55ms to complete controller restore state (CRS). There is no timeout limit mentioned in xhci specification so fixing the issue by increasing the timeout limit to 100ms [reformat code comment -Mathias] Signed-off-by: Ajay Gupta <ajaykuee@gmail.com> Signed-off-by: Nagaraj Annaiah <naga.annaiah@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-25xhci: Fix perceived dead host due to runtime suspend race with event handlerMathias Nyman
commit 229bc19fd7aca4f37964af06e3583c1c8f36b5d6 upstream. Don't rely on event interrupt (EINT) bit alone to detect pending port change in resume. If no change event is detected the host may be suspended again, oterwise roothubs are resumed. There is a lag in xHC setting EINT. If we don't notice the pending change in resume, and the controller is runtime suspeded again, it causes the event handler to assume host is dead as it will fail to read xHC registers once PCI puts the controller to D3 state. [ 268.520969] xhci_hcd: xhci_resume: starting port polling. [ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling. [ 268.521030] xhci_hcd: xhci_suspend: stopping port polling. [ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001 [ 268.521139] xhci_hcd: Port Status Change Event for port 3 [ 268.521149] xhci_hcd: resume root hub [ 268.521163] xhci_hcd: port resume event for port 3 [ 268.521168] xhci_hcd: xHC is not running. [ 268.521174] xhci_hcd: handle_port_status: starting port polling. [ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead The EINT lag is described in a additional note in xhci specs 4.19.2: "Due to internal xHC scheduling and system delays, there will be a lag between a change bit being set and the Port Status Change Event that it generated being written to the Event Ring. If SW reads the PORTSC and sees a change bit set, there is no guarantee that the corresponding Port Status Change Event has already been written into the Event Ring." Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-19xhci: fix deadlock at host remove by running watchdog correctlyMathias Nyman
commit d6169d04097fd9ddf811e63eae4e5cd71e6666e2 upstream. If a URB is killed while the host is removed we can end up in a situation where the hub thread takes the roothub device lock, and waits for the URB to be given back by xhci-hcd, blocking the host remove code. xhci-hcd tries to stop the endpoint and give back the urb, but can't as the host is removed from PCI bus at the same time, preventing the normal way of giving back urb. Instead we need to rely on the stop command timeout function to give back the urb. This xhci_stop_endpoint_command_watchdog() timeout function used a XHCI_STATE_DYING flag to indicate if the timeout function is already running, but later this flag has been taking into use in other places to mark that xhci is dying. Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still checking that reading from pci state does not return 0xffffffff or that host is not halted before trying to stop the endpoint. This whole area of stopping endpoints, giving back URBs, and the wathdog timeout need rework, this fix focuses on solving a specific deadlock issue that we can then send to stable before any major rework. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-12usb: xhci: fix return value of xhci_setup_device()Lu Baolu
commit 90797aee5d6902b49a453c97d83c326408aeb5a8 upstream. xhci_setup_device() should return failure with correct error number when xhci host has died, removed or halted. During usb device enumeration, if usb host is not accessible (died, removed or halted), the hc_driver->address_device() should return a corresponding error code to usb core. But current xhci driver just returns success. This misleads usb core to continue the enumeration by reading the device descriptor, which will result in failure, and users will get a misleading message like "device descriptor read/8, error -110". Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-07xhci: Make sure xhci handles USB_SPEED_SUPER_PLUS devices.Mathias Nyman
commit 0caf6b33452112e5a1186c8c964e90310e49e6bd upstream. In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS are handled like regular SuperSpeed devices. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-07-11xhci: Cleanup only when releasing primary hcdGabriel Krisman Bertazi
commit 27a41a83ec54d0edfcaf079310244e7f013a7701 upstream. Under stress occasions some TI devices might not return early when reading the status register during the quirk invocation of xhci_irq made by usb_hcd_pci_remove. This means that instead of returning, we end up handling this interruption in the middle of a shutdown. Since xhci->event_ring has already been freed in xhci_mem_cleanup, we end up accessing freed memory, causing the Oops below. commit 8c24d6d7b09d ("usb: xhci: stop everything on the first call to xhci_stop") is the one that changed the instant in which we clean up the event queue when stopping a device. Before, we didn't call xhci_mem_cleanup at the first time xhci_stop is executed (for the shared HCD), instead, we only did it after the invocation for the primary HCD, much later at the removal path. The code flow for this oops looks like this: xhci_pci_remove() usb_remove_hcd(xhci->shared) xhci_stop(xhci->shared) xhci_halt() xhci_mem_cleanup(xhci); // Free the event_queue usb_hcd_pci_remove(primary) xhci_irq() // Access the event_queue if STS_EINT is set. Crash. xhci_stop() xhci_halt() // return early The fix modifies xhci_stop to only cleanup the xhci data when releasing the primary HCD. This way, we still have the event_queue configured when invoking xhci_irq. We still halt the device on the first call to xhci_stop, though. I could reproduce this issue several times on the mainline kernel by doing a bind-unbind stress test with a specific storage gadget attached. I also ran the same test over-night with my patch applied and didn't observe the issue anymore. [ 113.334124] Unable to handle kernel paging request for data at address 0x00000028 [ 113.335514] Faulting instruction address: 0xd00000000d4f767c [ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1] [ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV [c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80 [c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0 [c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0 [xhci_pci] [c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110 [c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190 [c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70 [c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150 [c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0 [c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0 [c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0 [c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190 [c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200 [c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110 [c000000efe47be30] c000000000009260 system_call+0x38/0x108 Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Cc: Roger Quadros <rogerq@ti.com> Cc: joel@jms.id.au Reviewed-by: Roger Quadros <rogerq@ti.com> Tested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-05-04xhci: fix 10 second timeout on removal of PCI hotpluggable xhci controllersMathias Nyman
commit 98d74f9ceaefc2b6c4a6440050163a83be0abede upstream. PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will remove the xhci controller from the PCI bus when the last USB device is disconnected. Add a flag to indicate that the host is being removed to avoid queueing configure_endpoint commands for the dropped endpoints. For PCI hotplugged controllers this will prevent 5 second command timeouts For static xhci controllers the configure_endpoint command is not needed in the removal case as everything will be returned, freed, and the controller is reset. For now the flag is only set for PCI connected host controllers. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-05-04xhci: resume USB 3 roothub firstMathias Nyman
commit 671ffdff5b13314b1fc65d62cf7604b873fb5dc4 upstream. Give USB3 devices a better chance to enumerate at USB 3 speeds if they are connected to a suspended host. Solves an issue with NEC uPD720200 host hanging when partially enumerating a USB3 device as USB2 after host controller runtime resume. Tested-by: Mike Murdoch <main.haarp@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-02-25xhci: Fix list corruption in urb dequeue at host removalMathias Nyman
commit 5c82171167adb8e4ac77b91a42cd49fb211a81a0 upstream. xhci driver frees data for all devices, both usb2 and and usb3 the first time usb_remove_hcd() is called, including td_list and and xhci_ring structures. When usb_remove_hcd() is called a second time for the second xhci bus it will try to dequeue all pending urbs, and touches td_list which is already freed for that endpoint. Reported-by: Joe Lawrence <joe.lawrence@stratus.com> Tested-by: Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-31xhci: refuse loading if nousb is usedOliver Neukum
commit 1eaf35e4dd592c59041bc1ed3248c46326da1f5f upstream. The module should fail to load. Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-04usb: xhci: fix config fail of FS hub behind a HS hub with MTTChunfeng Yun
if a full speed hub connects to a high speed hub which supports MTT, the MTT field of its slot context will be set to 1 when xHCI driver setups an xHCI virtual device in xhci_setup_addressable_virt_dev(); once usb core fetch its hub descriptor, and need to update the xHC's internal data structures for the device, the HUB field of its slot context will be set to 1 too, meanwhile MTT is also set before, this will cause configure endpoint command fail, so in the case, we should clear MTT to 0 for full speed hub according to section 6.2.2 Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-18xhci: Workaround to get Intel xHCI reset working more reliablyRajmohan Mani
Existing Intel xHCI controllers require a delay of 1 mS, after setting the CMD_RESET bit in command register, before accessing any HC registers. This allows the HC to complete the reset operation and be ready for HC register access. Without this delay, the subsequent HC register access, may result in a system hang, very rarely. Verified CherryView / Braswell platforms go through over 5000 warm reboot cycles (which was not possible without this patch), without any xHCI reset hang. Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com> Tested-by: Joe Lawrence <joe.lawrence@stratus.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-16usb: xhci: configure 32-bit DMA if the controller does not support 64-bit DMADuc Dang
This change avoids DMA error in the cases where dma_mask and coherent_dma_mask of a 32-bit controller get configured as DMA_BIT_MASK(64) when running on a 64-bit system. Signed-off-by: Duc Dang <dhdang@apm.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-04xhci: check xhci hardware for USB 3.1 supportMathias Nyman
Set the controller speed to HCD_USB31 to if host hardware supports USB 3.1 For PCI xhci controllers the USB 3.1 support is checked from SBRN bits in pci config space. Platform controllers will need to set xhci->sbrn == 0x31 to indicate USB 3.1 support before calling xhci_gen_setup(). Also make sure xhci driver works correctly with speed set to HCD_USB31 Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-04xhci: Read and parse new xhci 1.1 capability registerLu Baolu
xhci 1.1 capable controllers have a new HCCPARAMS2 registers with bits indicating support for new xhci 1.1 capabilities. Also add support for the new xhci 1.1 bits in the config operational opertational register that used to be reserved Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> [modified and left out parts not related to HCCPARAMS2 -Mathias] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21usb: xhci: exit early in xhci_setup_device() if we're halted or dyingRoger Quadros
During quick plug/removal of OTG adapter during dual-role testing it can happen that xhci_alloc_device() is called for the newly detected device after the DRD library has called xhci_stop to remove the HCD. If that is the case, just fail early to prevent the following warning. [ 154.732649] hub 4-0:1.0: USB hub found [ 154.742204] hub 4-0:1.0: 1 port detected [ 154.824458] hub 3-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 154.854609] hub 4-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 154.944430] usb 3-1: new high-speed USB device number 2 using xhci-hcd [ 154.951009] xhci-hcd xhci-hcd.0.auto: xhci_setup_device [ 155.038191] xhci-hcd xhci-hcd.0.auto: remove, state 4 [ 155.043315] usb usb4: USB disconnect, device number 1 [ 155.055270] xhci-hcd xhci-hcd.0.auto: xhci_stop [ 155.060094] xhci-hcd xhci-hcd.0.auto: USB bus 4 deregistered [ 155.066576] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 155.071710] usb usb3: USB disconnect, device number 1 [ 155.077124] xhci-hcd xhci-hcd.0.auto: xhci_setup_device [ 155.082389] ------------[ cut here ]------------ [ 155.087690] WARNING: CPU: 0 PID: 72 at drivers/usb/host/xhci.c:3800 xhci_setup_device+0x410/0x484 [xhci_hcd]() [ 155.097861] Modules linked in: sd_mod usb_storage scsi_mod usb_f_ss_lb g_zero libcomposite ipv6 xhci_plat_hcd xhci_hcd usbcore dwc3 udc_core evdev ti_am335x_adc joydev kfifo_buf industrialio snd_soc_simple_cc [ 155.146734] CPU: 0 PID: 72 Comm: kworker/0:3 Tainted: G W 4.1.4-00834-gcd9380b-dirty #50 [ 155.156073] Hardware name: Generic AM43 (Flattened Device Tree) [ 155.162117] Workqueue: usb_hub_wq hub_event [usbcore] [ 155.167249] Backtrace: [ 155.169751] [<c0012af0>] (dump_backtrace) from [<c0012c8c>] (show_stack+0x18/0x1c) [ 155.177390] r6:c089d4a4 r5:ffffffff r4:00000000 r3:ee46c000 [ 155.183137] [<c0012c74>] (show_stack) from [<c05f7c14>] (dump_stack+0x84/0xd0) [ 155.190446] [<c05f7b90>] (dump_stack) from [<c00439ac>] (warn_slowpath_common+0x80/0xbc) [ 155.198605] r7:00000009 r6:00000ed8 r5:bf27eb70 r4:00000000 [ 155.204348] [<c004392c>] (warn_slowpath_common) from [<c0043a0c>] (warn_slowpath_null+0x24/0x2c) [ 155.213202] r8:ee49f000 r7:ee7c0004 r6:00000000 r5:ee7c0158 r4:ee7c0000 [ 155.220051] [<c00439e8>] (warn_slowpath_null) from [<bf27eb70>] (xhci_setup_device+0x410/0x484 [xhci_hcd]) [ 155.229816] [<bf27e760>] (xhci_setup_device [xhci_hcd]) from [<bf27ec10>] (xhci_address_device+0x14/0x18 [xhci_hcd]) [ 155.240415] r10:ee598200 r9:00000001 r8:00000002 r7:00000001 r6:00000003 r5:00000002 [ 155.248363] r4:ee49f000 [ 155.250978] [<bf27ebfc>] (xhci_address_device [xhci_hcd]) from [<bf20cb94>] (hub_port_init+0x1b8/0xa9c [usbcore]) [ 155.261403] [<bf20c9dc>] (hub_port_init [usbcore]) from [<bf2101e0>] (hub_event+0x738/0x1020 [usbcore]) [ 155.270874] r10:ee598200 r9:ee7c0000 r8:ee7c0038 r7:ee518800 r6:ee49f000 r5:00000001 [ 155.278822] r4:00000000 [ 155.281426] [<bf20faa8>] (hub_event [usbcore]) from [<c005754c>] (process_one_work+0x128/0x340) [ 155.290196] r10:00000000 r9:00000003 r8:00000000 r7:fedfa000 r6:eeec5400 r5:ee598314 [ 155.298151] r4:ee434380 [ 155.300718] [<c0057424>] (process_one_work) from [<c00578f8>] (worker_thread+0x158/0x49c) [ 155.308963] r10:ee434380 r9:00000003 r8:eeec5400 r7:00000008 r6:ee434398 r5:eeec5400 [ 155.316913] r4:eeec5414 [ 155.319482] [<c00577a0>] (worker_thread) from [<c005cc40>] (kthread+0xdc/0xf8) [ 155.326765] r10:00000000 r9:00000000 r8:00000000 r7:c00577a0 r6:ee434380 r5:ee4441c0 [ 155.334713] r4:00000000 r3:00000000 [ 155.338341] [<c005cb64>] (kthread) from [<c000fc08>] (ret_from_fork+0x14/0x2c) [ 155.345626] r7:00000000 r6:00000000 r5:c005cb64 r4:ee4441c0 [ 155.356108] ---[ end trace a58d34c223b190e6 ]--- [ 155.360783] xhci-hcd xhci-hcd.0.auto: Virt dev invalid for slot_id 0x1! [ 155.574404] xhci-hcd xhci-hcd.0.auto: xhci_setup_device [ 155.579667] ------------[ cut here ]------------ Cc: <stable@vger.kernel.org> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21usb: xhci: stop everything on the first call to xhci_stopRoger Quadros
xhci_stop will be called twice, once for the shared hcd and again for the primary hcd. We stop the XHCI controller in any case so clean up everything on the first call else we can timeout waiting for pending requests to complete. Cc: <stable@vger.kernel.org> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21usb: xhci: Clear XHCI_STATE_DYING on startRoger Quadros
For whatever reason if XHCI died in the previous instant then it will never recover on the next xhci_start unless we clear the DYING flag. Cc: <stable@vger.kernel.org> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21usb: xhci: lock mutex on xhci_stopRoger Quadros
Else it races with xhci_setup_device Cc: <stable@vger.kernel.org> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-08usb: xhci: Add support for URB_ZERO_PACKET to bulk/sg transfersReyad Attiyat
This commit checks for the URB_ZERO_PACKET flag and creates an extra zero-length td if the urb transfer length is a multiple of the endpoint's max packet length. Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-05usb: host: xhci: Simplify return statementSaurabh Karajgaonkar
Replace redundant variable use in return statement. Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-27Merge 4.2-rc4 into usb-nextGreg Kroah-Hartman
We want the USB fixes that went into that release in this branch as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-22usb: host: xhci: remove typo in function documentationLuis de Bethencourt
Fix "though" to "through" in documentation of xhci_alloc_streams(). Signed-off-by: Luis de Bethencourt <luis@debethencourt.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-22xhci: Calculate old endpoints correctly on device resetBrian Campbell
When resetting a device the number of active TTs may need to be corrected by xhci_update_tt_active_eps, but the number of old active endpoints supplied to it was always zero, so the number of TTs and the bandwidth reserved for them was not updated, and could rise unnecessarily. This affected systems using Intel's Patherpoint chipset, which rely on software bandwidth checking. For example, a Lenovo X230 would lose the ability to use ports on the docking station after enough suspend/resume cycles because the bandwidth calculated would rise with every cycle when a suitable device is attached. The correct number of active endpoints is calculated in the same way as in xhci_reserve_bandwidth. Cc: <stable@vger.kernel.org> Signed-off-by: Brian Campbell <bacam@z273.org.uk> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-08Merge 4.1-rc7 into usb-nextGreg Kroah-Hartman
This resolves a merge issue in musb_core.c and we want the fixes that were in Linus's tree in this branch as well for testing. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-31usb: host: xhci: remove incorrect comment about mutexChris Bainbridge
The comment stating that xhci_setup_device() is protected by the address mutex is not true since commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus") as xhci handles two buses. Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-31usb: xhci: Fix suspend/resume when used with OTG coreRoger Quadros
In the OTG case, the controller might not yet have been added or is removed before the system suspends. Assign xhci->main_hcd during probe to prevent NULL pointer de-reference in xhci_suspend/resume(). Use the hcd->state flag to check if HCD is halted and if that is so do nothing for xhci_suspend/resume(). [Only for xhci-plat devices, pci devices need it in gen_setup -Mathias] Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-31usb: xhci: Allow usb_add/remove_hcd() to be called repeatedlyRoger Quadros
Don't set xhci->shared_hcd to NULL in xhci_stop() as we have still not de-allocated it. It was resulting in a NULL pointer de-reference if usb_add/remove_hcd() is called repeatedly. We want repeated add/remove to work for the OTG use case. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-31usb: xhci: cleanup xhci_hcd allocationRoger Quadros
HCD core allocates memory for HCD private data in usb_create_[shared_]hcd() so make use of that mechanism to allocate the struct xhci_hcd. Introduce struct xhci_driver_overrides to provide the size of HCD private data and hc_driver operation overrides. As of now we only need to override the reset and start methods. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24usb: host: xhci: add mutex for non-thread-safe dataChris Bainbridge
Regression in commit 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel") The regression resulted in intermittent failure to initialise a 10-port hub (with three internal VL812 4-port hub controllers) on boot, with a failure rate of around 8%, due to multiple race conditions when accessing addr_dev and slot_id in struct xhci_hcd. This regression also exposed a problem with xhci_setup_device, which "should be protected by the usb_address0_mutex" but no longer is due to commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus") With separate buses (and locks) it is no longer the case that a single lock will protect xhci_setup_device from accesses by two parallel threads processing events on the two buses. Fix this by adding a mutex to protect addr_dev and slot_id in struct xhci_hcd, and by making the assignment of slot_id atomic. Fixes multiple boot errors: [ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2 [ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures [ 0.583012] usb usb1-port3: couldn't allocate usb_device And: [ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID [ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32. [ 0.637421] usb usb1-port1: couldn't allocate usb_device And: [ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0. [ 0.753373] usb 1-3: hub failed to enable device, error -22 [ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID [ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32. [ 0.753403] usb usb1-port3: couldn't allocate usb_device And: [ 11.018386] usb 1-3: device descriptor read/all, error -110 And: [ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command Tested with 200 reboots, resulting in no USB hub init related errors. Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel") Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.com Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com> Cc: <stable@vger.kernel.org> # 3.18+ [changed git commit description style for checkpatch -Mathias] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24usb: make module xhci_hcd removableArthur Demchenkov
Fixed regression. After commit 29e409f0f761 ("xhci: Allow xHCI drivers to be built as separate modules") the module xhci_hcd became non-removable. That behaviour is not expected and there're no notes about it in commit message. The module should be removable as it blocks PM suspend/resume functions (Debian Bug#666406). Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> Reviewed-by: Andrew Bresticker <abrestic@chromium.org> Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-11Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"Mathias Nyman
This reverts commit 27082e2654dc ("xhci: Clear the host side toggle manually") Turns out this fix to enable soft resetting endpoints wasn't mature enough. It caused regression with some usb DVB-T devices and needs some more tuning to get the endpiont ring pointers set correctly. The original commit was tagged for stable 3.18, and should be reverted from there as well. Cc: stable <stable@vger.kernel.org> # v3.18 Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-24xhci: Clear the host side toggle manually when endpoint is 'soft reset'Mathias Nyman
Main benefit of this is to get xhci connected USB scanners to work. Some devices use a clear endpoint halt request as a 'soft reset' even if the endpoint is not halted. This will clear the toggle and sequence on the device side. xHCI however refuses to reset a non-halted endpoint, so instead we need to issue a configure endpoint command on xHCI to clear its host side toggle and sequence, and get it in sync with the device side. Tested-by: Mike Mammarella <mikem@crystalorb.net> Cc: <stable@vger.kernel.org> # v3.18 Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-25xhci: Silence "xHCI xhci_drop_endpoint called with disabled ep ..." messagesHans de Goede
When re-applying the configuration after a successful usb device reset, xhci_discover_or_reset_device has already dropped the endpoints, and free-ed the rings. The endpoints already being dropped is expected, and should not lead to warnings. Use the fact that the rings are also free-ed in this scenario to detect this, and suppress the "xHCI xhci_drop_endpoint called with disabled ep ..." message in this case. Signed-off-by: Hans de Goede <hdegoede@redhat.com> -- Changes in v2: Move the ring check to only guard the xhci_warn, so as to avoid side-effects in case we have a scenario where the rings are free-ed, but the endpoint is not yet dropped. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-25xhci: Print hcc params, version and quirks on initHans de Goede
To help debugging xhci problems. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-27 15:42:31 +0000