| Age | Commit message (Collapse) | Author |
|---|
|
commit b3207c65dfafae27e7c492cb9188c0dc0eeaf3fd upstream.
xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times
without checking the return value. xhci_queue_stop_endpoint() can
return error if the HC is already halted or unable to queue commands.
This can cause a deadlock condition as xhci_stop_device() would
end up waiting indefinitely for a completion for the command that
didn't get queued. Fix this by checking the return value and bailing
out of xhci_stop_device() in case of error. This patch happens to fix
potential memory leaks of the allocated command structures as well.
Fixes: c311e391a7ef ("xhci: rework command timeout and cancellation,")
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a838a13c9b4e5dd188b7a6eaeb894e9358ead0c upstream.
xhci driver keeps a bus_state structure for each hcd (usb2 and usb3)
The structure is picked based on hcd speed, but driver only compared
for HCD_USB3 speed, returning the wrong bus_state for HCD_USB31 hosts.
This caused null pointer dereference errors in bus_resume function.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 114ec3a6f9096d211a4aff4277793ba969a62c73 upstream.
Servers were emitting failed handoff messages but were not
waiting the full 1 second as designated in section 4.22.1 of
the eXtensible Host Controller Interface specifications. The
handshake was using wrong units so calls were made with milliseconds
not microseconds. Comments referenced 5 seconds not 1 second as
in specs.
The wrong units were also corrected in a second handshake call.
Signed-off-by: Jim Dickerson <jim.dickerson@hpe.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6b422b88b46353cf596e0db6dc0e39d50d90d6e upstream.
The following commit cause a regression on ATI chipsets.
'commit e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e788787ef4f9c24aafefc480a8da5f92b914e5e6 upstream.
Certain HP keyboards would keep inputting a character automatically which
is the wake-up key after S3 resume
On some AMD platforms USB host fails to respond (by holding resume-K) to
USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures
that resume is signaled for at least 20 ms (TDRSMDN), which is defined in
USB 2.0 spec. The result is that the keyboard is out of function.
In SNPS USB design, the host responds to the resume request only after
system gets back to S0 and the host gets to functional after the internal
HW restore operation that is more than 1 second after the initial resume
request from the USB device.
As a workaround for specific keyboard ID(HP Keyboards), applying port reset
after resume when the keyboard is plugged in.
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b895868bb2da60a386a17cde3bf9ecbc70c79f4 upstream.
This off by one in stream_id indexing caused NULL pointer dereference and
soft lockup on machines with USB attached SCSI devices connected to a
hotpluggable xhci controller.
The code that cleans up pending URBs for dead hosts tried to dereference
a stream ring at the invalid stream_id 0.
ep->stream_info->stream_rings[0] doesn't point to a ring.
Start looping stream_id from 1 like in all the other places in the driver,
and check that the ring exists before trying to kill URBs on it.
Reported-by: rocko r <rockorequin@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a54408d0a004757789863d74e29c2297edae0b4d upstream.
A uncleared PLC (port link change) bit will prevent furuther port event
interrupts for that port. Leaving it uncleared caused get_port_status()
to timeout after 20000ms while waiting to get the final port event
interrupt for resume -> U0 state change.
This is a targeted fix for a specific case where we get a port resume event
racing with xhci resume. The port event interrupt handler notices xHC is
not yet running and bails out early, leaving PLC uncleared.
The whole xhci port resuming needs more attention, but while working on it
it anyways makes sense to always ensure PLC is cleared in get_port_status
before setting a new link state and waiting for its completion.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2f48f05cd2a2a0a708fbfa45f1a00a87660d937 upstream.
When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed
With this patch applied, I get no more printing of this message.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd14a3e9b92ac6f0918054f9e3477438760a4fa6 upstream.
The timeout for BULK packets was 300ms which is a long time if other
endpoints or devices are waiting for their turn. Changing it to 50ms
greatly increased the overall performance for multi-endpoint devices.
Fixes: 5d3043586db4 ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f873d857b6c2fefb4dada952674aa01bcfb92bd upstream.
If multiple endpoints on a single device have pending IN URBs and one
endpoint times out due to NAKs (perfectly legal), select a different
endpoint URB to try.
The existing code only checked to see another device address has pending
URBs and ignores other IN endpoints on the current device address. This
leads to endpoints never getting serviced if one endpoint is using NAK as
a flow control method.
Fixes: 5d3043586db4 ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7480d912d549f414e0ce39331870899e89a5598c upstream.
According to xHCI ch4.20 Scratchpad Buffers, the Scratchpad
Buffer needs to be zeroed.
...
The following operations take place to allocate
Scratchpad Buffers to the xHC:
...
b. Software clears the Scratchpad Buffer to '0'
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0c16630d35a874e82bdf2088f58ecaca1024315 upstream.
Intel Denverton microserver is Atom based and need the PME and CAS quirks
as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b148d5144d64ee135b8924350cb0b3a7fd21150 upstream.
platform_get_irq() returns an error code, but the xhci-plat driver
ignores it and always returns -ENODEV. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fc091fb0459ade939a795bfdcaf645385b951d4 upstream.
Print correct command ring address using 'val_64'.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
paths
commit 68bd6fc3cfa98ef253e17307ccafd8ef907b5556 upstream.
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9b6 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
paths
commit 3f6026b1dcb3c8ee71198c485a72ac674c6890dd upstream.
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9b6 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcc7620cad5ad1326a78f4031a7bf4f0e5b42984 upstream.
Upstream commit 98d74f9ceaef ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.
The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.
The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f95e60a7dbecd2de816bb3ad517b3d4fbc20b507 upstream.
According to xHCI spec, HCIVERSION containing a BCD encoding
of the xHCI specification revision number, 0100h corresponds
to xHCI version 1.0. Change "100" as "0x100".
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Fixes: 04abb6de2825 ("xhci: Read and parse new xhci 1.1 capability register")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5de4e1ea9a731cad195ce5152705c21daef3bbba upstream.
The commit 4ac53087d6d4 ("usb: xhci: plat: Create both
HCDs before adding them") move add hcd to the end of
probe, this cause hcc_params uninitiated, because xHCI
driver sets hcc_params in xhci_gen_setup() called from
usb_add_hcd().
This patch checks the Maximum Primary Stream Array Size
in the hcc_params register after add primary hcd.
Signed-off-by: William wu <william.wu@rock-chips.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Fixes: 4ac53087d6d4 ("usb: xhci: plat: Create both HCDs before adding them")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6169d04097fd9ddf811e63eae4e5cd71e6666e2 upstream.
If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.
xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.
Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.
Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.
This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c111b6c3844a142e03bcfc2fa17bfbdea08e9dc upstream.
Current abort operation has race.
xhci_handle_command_timeout()
xhci_abort_cmd_ring()
xhci_write_64(CMD_RING_ABORT)
xhci_handshake(5s)
do {
check CMD_RING_RUNNING
udelay(1)
...
COMP_CMD_ABORT event
COMP_CMD_STOP event
xhci_handle_stopped_cmd_ring()
restart cmd_ring
CMD_RING_RUNNING become 1 again
} while ()
return -ETIMEDOUT
xhci_write_64(CMD_RING_ABORT)
/* can abort random command */
To do abort operation correctly, we have to wait both of COMP_CMD_STOP
event and negation of CMD_RING_RUNNING.
But like above, while timeout handler is waiting negation of
CMD_RING_RUNNING, event handler can restart cmd_ring. So timeout
handler never be notice negation of CMD_RING_RUNNING, and retry of
CMD_RING_ABORT can abort random command (BTW, I guess retry of
CMD_RING_ABORT was workaround of this race).
To fix this race, this moves xhci_handle_stopped_cmd_ring() to
xhci_abort_cmd_ring(). And timeout handler waits COMP_CMD_STOP event.
At this point, timeout handler is owner of cmd_ring, and safely
restart cmd_ring by using xhci_handle_stopped_cmd_ring().
[FWIW, as bonus, this way would be easily extend to add CMD_RING_PAUSE
operation]
[locks edited as patch is rebased on other locking fixes -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb4d5ce588c5ff68e0fdd30370a0e6bc2c0a736b upstream.
This is preparation to fix abort operation race (See "xhci: Fix race
related to abort operation"). To make timeout sleepable, use
delayed_work instead of timer.
[change a newly added pending timer fix to pending work -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c95a9f83711bf53faeb4ed9bbb63a3f065613dfb upstream.
We normally use the passed in gfp flags for allocations, it's just these
two which were missed.
Fixes: 22d45f01a836 ("usb/xhci: replace pci_*_consistent() with dma_*_coherent()")
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4dea70778c0f48b4385c7720c363ec8d37a401b4 upstream.
In command timer function, xhci_handle_command_timeout(), xhci->lock
is unlocked before call into xhci_abort_cmd_ring(). This might cause
race between the timer function and the event handler.
The xhci_abort_cmd_ring() function sets the CMD_RING_ABORT bit in the
command register and polling it until the setting takes effect. A stop
command ring event might be handled between writing the abort bit and
polling for it. The event handler will restart the command ring, which
causes the failure of polling, and we ever believed that we failed to
stop it.
As a bonus, this also fixes some issues of calling functions without
locking in xhci_handle_command_timeout().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5a1b9514154437aa1ed35c291191f82fd3e941a upstream.
If we get a command completion event at the same time as the command
timeout work starts on another cpu we might end up aborting the wrong
command.
If the command completion takes the xhci lock before the timeout work, it
will handle the command, pick the next command, mark it as current_cmd, and
re-queue the timeout work. When the timeout work finally gets the lock
It will start aborting the wrong command.
This case can be resolved by checking if the timeout work is pending inside
the timeout function itself. A new timeout work can only be pending if the
command completed and a new command was queued.
If there are no more commands pending then command completion will set
the current_cmd to NULL, which is already handled in the timeout work.
Reported-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a7cfdf37b7c08ac29df4c62ea5ccb01474b6597 upstream.
When current command was supposed to be aborted, host will free the command
in handle_cmd_completion() function. But it might be still referenced by
xhci->current_cmd, which need to set NULL.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90797aee5d6902b49a453c97d83c326408aeb5a8 upstream.
xhci_setup_device() should return failure with correct error number
when xhci host has died, removed or halted.
During usb device enumeration, if usb host is not accessible (died,
removed or halted), the hc_driver->address_device() should return
a corresponding error code to usb core. But current xhci driver just
returns success. This misleads usb core to continue the enumeration
by reading the device descriptor, which will result in failure, and
users will get a misleading message like "device descriptor read/8,
error -110".
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee8665e28e8d90ce69d4abe5a469c14a8707ae0e upstream.
the tt_info provided by a HS hub might be in use to by a child device
Make sure we free the devices in the correct order.
This is needed in special cases such as when xhci controller is
reset when resuming from hibernate, and all virt_devices are freed.
Also free the virt_devices starting from max slot_id as children
more commonly have higher slot_id than parent.
Reported-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c97cfc1a097b1e0786c836e92b7a72b4d031e25 upstream.
Intel Apollo Lake also requires XHCI_PME_STUCK_QUIRK.
Adding its PCI ID to quirk.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 346e99736c3ce328fd42d678343b70243aca5f36 upstream.
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b985467371a58ae44d76c7ba12b0951fee6ed98 upstream.
handle_cmd_completion() frees a command structure which might be still
referenced by xhci->current_cmd.
This might cause problem when xhci->current_cmd is accessed after that.
A real-life case could be like this. The host takes a very long time to
respond to a command, and the command timer is fired at the same time
when the command completion event arrives. The command completion
handler frees xhci->current_cmd before the timer function can grab
xhci->lock. Afterward, timer function grabs the lock and go ahead with
checking and setting members of xhci->current_cmd.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ccdb6be9ec6580ef69f68949ebe26e0fb58a6fb0 upstream.
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4c39135aa412d2f1381e43802523da110ca7855c upstream.
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.
Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed6d6f8f42d7302f6f9b6245f34927ec20d26c12 upstream.
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"
Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d3b016a6f5a0fa610dfd02b05654c08fa4ae514 upstream.
USB2 host inititated resume, and system suspend bus resume
need to use the same USB_RESUME_TIMEOUT as elsewhere.
This resolves a device disconnect issue at system resume seen
on Intel Braswell and Apollolake, but is in no way limited to
those platforms.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bcf42aa60c2832510b9be0f30c090bfd35bb172d upstream.
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0caf6b33452112e5a1186c8c964e90310e49e6bd upstream.
In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS
are handled like regular SuperSpeed devices.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1f6d9a8b540df22b87a5bf6bc104edaade81f47 upstream.
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 88716a93766b8f095cdef37a8e8f2c93aa233b21 upstream.
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33be126510974e2eb9679f1ca9bca4f67ee4c4c7 upstream.
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc337b51508beb2d039aff5074a76cfe1c212030 upstream.
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.
This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.
Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c66f59ee5050447b3da92d36f5385a847990a894 upstream.
Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.
This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.
The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.
Fix ed_schedule to update ED state only on successful return.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8a15a9650694feaa0dabf197b0c94d37cd3fb42 upstream.
There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.
Commit a47cc24cd1e5 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.
This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.
Fixes: a47cc24cd1e5 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3425aa03f484d45dc21e0e791c2f6c74ea656421 upstream.
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d95815ba6a0f287213118c136e64d8c56daeaeab upstream.
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de95c40d5beaa47f6dc8fe9ac4159b4672b51523 upstream.
On some platforms, the clocks might be registered by a platform
driver. When this is the case, the clock platform driver may very well
be probed after xhci-plat, in which case the first probe() invocation
of xhci-plat will receive -EPROBE_DEFER as the return value of
devm_clk_get().
The current code handles that as a normal error, and simply assumes
that this means that the system doesn't have a clock for the XHCI
controller, and continues probing without calling
clk_prepare_enable(). Unfortunately, this doesn't work on systems
where the XHCI controller does have a clock, but that clock is
provided by another platform driver. In order to fix this situation,
we handle the -EPROBE_DEFER error condition specially, and abort the
XHCI controller probe(). It will be retried later automatically, the
clock will be available, devm_clk_get() will succeed, and the probe()
will continue with the clock prepared and enabled as expected.
In practice, such issue is seen on the ARM64 Marvell 7K/8K platform,
where the clocks are registered by a platform driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27a41a83ec54d0edfcaf079310244e7f013a7701 upstream.
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b09d ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 98d74f9ceaefc2b6c4a6440050163a83be0abede upstream.
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71504062a7c34838c3fccd92c447f399d3cb5797 upstream.
This patch fixes some wild pointers produced by xhci_mem_cleanup.
These wild pointers will cause system crash if xhci_mem_cleanup()
is called twice.
Reported-and-tested-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 671ffdff5b13314b1fc65d62cf7604b873fb5dc4 upstream.
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
