| Age | Commit message (Collapse) | Author |
|---|
|
commit 62a6abdd427b5fc4d8aad5dac874904e96273e6d upstream.
When dma_addr_t is 64-bit, we get a warning about an invalid cast
in the call to ux500_dma_is_compatible() from ux500_dma_channel_program():
drivers/usb/musb/ux500_dma.c: In function 'ux500_dma_channel_program':
drivers/usb/musb/ux500_dma.c:210:51: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
if (!ux500_dma_is_compatible(channel, packet_sz, (void *)dma_addr, len))
The problem is that ux500_dma_is_compatible() is called from the
main musb driver on the virtual address, but here we pass in a
DMA address, so the types are fundamentally different but it works
because the function only checks the alignment of the buffer and
that is the same.
We could work around this by adding another cast, but I have checked
that the buffer we get passed here is already checked before it
gets mapped, so the second check seems completely unnecessary
and removing it must be the cleanest solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79c5623f1cb85f33403eb9f1e45124e9f56181f8 upstream.
The commit 7d32cdef5356 ("usb: musb: fail with error when no DMA
controller set"), caused the core platform driver to correctly return an
error code when fail probing.
Unfurtante it also caused bug for a NULL pointer dereference, during
system suspend for the ux500 driver. The reason is a lacking validation
of the corresponding ->driver_data pointer, which won't be set when the
musb core driver fails to probe (or haven't yet been probed).
Fixes: 7d32cdef5356 ("usb: musb: fail with error when no DMA...")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd3486ded7a0c313a6575343e6c2b21d14476645 upstream.
When babble condition happens, the musb controller might automatically
turns off VBUS. On DA8xx platform, the controller generates drvvbus
interrupt for turning off VBUS along with the babble interrupt.
In this case, we should handle the babble interrupt first and recover
from the babble condition.
This change ignores the drvvbus interrupt if babble interrupt is also
generated at the same time, so the babble recovery routine works
properly.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 445ef61543da3db5b699f87fb0aa4f227165f6ed upstream.
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ed05c68cbcae42cd52b8e53b66952bfa9c002ce upstream.
This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45d73860530a14c608f410b91c6c341777bfa85d upstream.
commit 68fe05e2a451 ("usb: musb: fix tx fifo flush handling") drops the
1ms delay trying to solve the long disconnect time issue when
application queued many tx urbs. However, the 1ms delay is needed for
some use cases, for example, without the delay, reconnecting AR9271 WIFI
dongle no longer works if the connection is dropped from the AP.
So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the
long disconnect time problem with a separate patch for
usb_hcd_flush_endpoint().
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6df2b42f7c040d57d9ecb67244e04e905ab87ac6 upstream.
We have one register for each EP to set the maximum packet size for both
TX and RX.
If for example an RX programming would happen before the previous TX
transfer finishes we would reset the TX packet side.
To fix this issue, only modify the TX or RX part of the register.
Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0090114d336a9604aa2d90bc83f20f7cd121b76c upstream.
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d83d6 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a994ce2d7e66008381a0b184c73be9ae9b72eb5c upstream.
DA8xx driver is registering and using the CPPI 3.0 DMA controller but
actually, the DA8xx has a CPPI 4.1 DMA controller.
Remove the CPPI 3.0 quirk and methods.
Fixes: f8e9f34f80a2 ("usb: musb: Fix up DMA related macros")
Fixes: 7f6283ed6fe8 ("usb: musb: Set up function pointers for DMA")
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5563bb5743cb09bde0d0f4660a5e5b19c26903bf upstream.
The function bfin_fifo_offset is defined but not used:
drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
static u32 bfin_fifo_offset(u8 epnum)
^~~~~~~~~~~~~~~~
Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.
Fixes: cc92f6818f6e ("usb: musb: Populate new IO functions for blackfin")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c300fe282fa254ea730c92cb0983e2642dc1fff upstream.
When unloading omap2430, we can get the following splat:
WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<c01a8b78>] (free_irq) from [<bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>]
(platform_drv_remove+0x24/0x3c)
...
This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.
Fixes: 6995eb68aab7 ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c48400baa02155a5ddad63e8554602e48782278c upstream.
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6def85a396ce7796bd9f4561c6ae8138833f7a52 upstream.
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt.
Clearing ep interrupt is platform dependent, so this patch adds a
platform callback to allow glue driver to clear the ep interrupt.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4c2ba0c67394514f3f75c660c9f5d02e66a7efd4 upstream.
Commit ac33cdb16681 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bba40e6948b94cba71965285fbac31bd078c024a upstream.
Commit 754fe4a92c07 ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Cc: Adam Ford <aford173@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04471eb8c3158c0ad9df4b24da845a63b2e8f23a upstream.
Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(),
which causes kernel NULL pointer reference oops later when calling
cppi41_dma_channel_program().
Fixes: 069a3fd (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c
part1)
Reported-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3eec0cf784e0d6c47822ca6b66df3d5812af7e6 upstream.
shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b2c17f829545df27a910e8d82e133c21c9a8c9c upstream.
Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84ac5d1140f716a616522f952734e850448d2556 upstream.
If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.
This solves the device enumeration failure in otg mode exposed by commit
56f487c (PM / Runtime: Update last_busy in rpm_resume).
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fail with error when no DMA controller is set.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If musb_init_controller fails at musb_platform_init, we have already
called pm_runtime_irq_safe for musb and that causes the pm runtime count
to be enabled for parent before the parent has completed initialization.
This causes pm to stop working as on unload nothing gets idled.
This issue can be reproduced at least with:
# modprobe omap2430
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
# modprobe phy-twl4030-usb
# rmmod omap2430
And after the steps above omap2430 will block deeper idle states on
omap3.
To fix this, let's not enable pm runtime until we need to and the
parent has been initialized. Note that this does not fix the issue of
PM being broken for musb during runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The CPPI-4.1 driver selects TI_CPPI41, which is a dmaengine
driver and that may not be available when CONFIG_DMADEVICES
is not set:
warning: (USB_TI_CPPI41_DMA) selects TI_CPPI41 which has unmet direct dependencies (DMADEVICES && ARCH_OMAP)
This adds an extra dependency to avoid generating warnings in randconfig
builds. Ideally we'd remove the 'select' statement, but that has the
potential to break defconfig files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 411dd19c682d ("usb: musb: Kconfig: Select the DMA driver if DMA mode of MUSB is enabled")
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Change the permission of usb_dma parameter so it can
be used for runtime debug without reboot.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Here are a few changes in musb_h_tx_flush_fifo().
- It has been observed that sometimes (if not always) musb is unable
to flush tx fifo during urb dequeue when disconnect a device. But
it seems to be harmless, since the tx fifo flush is done again in
musb_ep_program() when re-use the hw_ep.
But the WARN() floods the console in the case when multiple tx urbs
are queued, so change it to dev_WARN_ONCE().
- applications could queue up many tx urbs, then the 1ms delay could
causes minutes of delay in device disconnect. So remove it to get
better user experience. The 1ms delay does not help the flushing
anyway.
- cleanup the debug code - related to lastcsr.
----
Note: The tx fifo flush issue has been observed during device disconnect
on AM335x.
To reproduce the issue, ensure tx urb(s) are queued when unplug the usb
device which is connected to AM335x usb host port.
I found using a usb-ethernet device and running iperf (client on AM335x)
has very high chance to trigger the problem.
Better to turn on dev_dbg() in musb_cleanup_urb() with CPPI enabled to
see the issue when aborting the tx channel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
There is a bit of a mess in the order of arguments to the ulpi write
callback. There is
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
in drivers/usb/common/ulpi.c;
struct usb_phy_io_ops {
...
int (*write)(struct usb_phy *x, u32 val, u32 reg);
}
in include/linux/usb/phy.h.
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e460 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while"
* tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (233 commits)
USB: core: Codestyle fix in urb.c
usb: misc: usb3503: Use i2c_add_driver helper macro
usb: host: lpc32xx: don't unregister phy device
usb: host: lpc32xx: balance clk enable/disable on removal
usb: host: lpc32xx: fix warnings caused by enabling unprepared clock
uwb: drp: Use setup_timer
uwb: neh: Use setup_timer
uwb: rsv: Use setup_timer
USB: qcserial: add Sierra Wireless MC74xx/EM74xx
usb: chipidea: otg: don't wait vbus drops below BSV when starts host
chipidea: ci_hdrc_pci: use PCI_VDEVICE() instead of PCI_DEVICE()
doc: dt-binding: ci-hdrc-usb2: split vendor specific properties
usb: chipidea: imx: add imx6ul usb support
doc: dt-binding: ci-hdrc-usb2: improve property description
usb: chipidea: imx: add usb support for imx7d
Doc: usb: ci-hdrc-usb2: Add phy-clkgate-delay-us entry
usb: chipidea: Add support for 'phy-clkgate-delay-us' property
usb: chipidea: Use extcon framework for VBUS and ID detect
usb: gadget: net2280: restore ep_cfg after defect7374 workaround
usb: dwc2: host: Fix use after free w/ simultaneous irqs
...
|
|
Commit ddef08dd00f5 ("Driver core: wakeup the parent device before trying
probe") started automatically ensuring the parent device is enabled when
the child gets probed.
This however caused a regression for MUSB omap2430 interface as the
runtime PM for the parent device needs the child initialized to access
the MUSB hardware registers.
Let's delay the enabling of PM runtime for the parent until the child
has been properly initialized as suggested in an earlier patch by
Grygorii Strashko <grygorii.strashko@ti.com>.
In addition to delaying pm_runtime_enable, we now also need to make sure
the parent is enabled during omap2430_musb_init. We also want to propagate
an error from omap2430_runtime_resume if struct musb is not initialized.
Note that we use pm_runtime_put_noidle here for both the child and parent
to prevent an extra runtime_suspend/resume cycle.
Let's also add some comments to avoid confusion between the
two different devices.
Fixes: ddef08dd00f5 ("Driver core: wakeup the parent device before
trying probe")
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix musb_platform_get_vbus_status return value in case of platform
implementation is not defined, bringing expected behaviour of
musb_platform_get wrapper. Add musb_vbus_show default method to determine
VBUS status in case platform method is not defined.
Signed-off-by: Roman Alyautdin <ralyautdin@dev.rtsoft.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Now that it is possible to build in multiple dma engines, we can no longer
require MUSB_PIO_ONLY to be set when using the sunxi musb glue.
This patch adds dummy dma hooks to make the musb glue work without
MUSB_PIO_ONLY. This hooks are fake because we do not support dma with
musb on sunxi. The Allwinnner Android kernels have some dma code, but it
is disabled as Allwinner never managed to get it to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Set musb config->maximum_speed based on the dts setting to control musb
speed.
By default musb works in high-speed mode. Adding
maximum-speed = "full-speed";
to dts usb node will force musb to full-speed mode.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Set the Power register HSENAB bit based on musb->config->maximum_speed,
so that the glue layer can control MUSB to work in high- or full-speed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
After a few iterations of start/stop UVC camera streaming, the streaming
stops.
This patch adds 250us delay in the cppi channel abort path to let cppi
drain properly.
Using 50us delay seems to be too aggressive, some webcams are still
broken. 250us is the original value used in TI 3.2 kernel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fix the regression caused by commit ad78c918602 ("usb: musb: dsps: just
start polling already") which causes polling the ID pin status even in
device-only mode.
Fixes: ad78c918602c ("usb: musb: dsps: just start polling already")
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In certain situations, an interrupt triggers on resume, before musb_start()
has been called. This has been observed to cause enumeration issues after
suspend/resume cycles with AM335x.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The change ensures otg is not in a A- state when checking for VBUS in
peripheral mode.
musb_start() where VBUS checking is in can be called in many situations.
One example is in babble recovery routine, in which otg is transitioning
from A-HOST to A-WAIT-BCON, but VBUS discharge takes time, so
musb->is_active could be set to 1 due to this improper checking, then it
causes musb_bus_suspend() failed which leads to warning log message
flooding.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add missing break after 'default' label to fix compilation error.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
since commit 33c300cb90a6 ("usb: musb: dsps:
don't fake of_node to musb core") we have been
preventing CPPI 4.1 from probing due to NULL
of_node. We can't revert said commit otherwise
a different regression would show up, so the fix
is to look for the parent device's (glue layer's)
of_node instead, since that's the thing which
is actually described in DTS.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Commit fb91cddc54e7 ("usb: musb: Remove DMA
ifdef for musb_gadget.c short_packet") tried
to remove DMA ifdeferry from musb_gadget.c
but ended up leaving some around.
Remove them so that when building kernels with
all DMA engines enabled, we don't end up trying
to allocte channels twice.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Replace redundant variable use in return statement.
Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
With recent changes to MUSB code, we can now now get rid of
the Kconfig choise for the DMA code and allow building in any
of the desired DMA code. This makes life easier for distros.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Due to some UDC controllers may not support zlp, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_zlp_not_supp' field to struct usb_gadget and helper
function gadget_is_zlp_supported(). It also sets 'quirk_zlp_not_supp'
to 1 in musb UDC driver, which has such limitation.
[ balbi@ti.com : make it build ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The A33 SoC uses the same musb controller as found on the A31 and later,
but allwinner has removed the configdata register, this commit adds special
handling for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.
This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.
This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Currently, we're calling musb_start() twice for DRD ports
in some situations. This has been observed to cause enumeration
issues after suspend/resume cycles with AM335x.
In order to fix the problem, we just have to fix the check
on musb_has_gadget() so that it only returns true if
current mode is Host and ignore the fact that we have or
not a gadget driver loaded.
Fixes: ae44df2e21b5 (usb: musb: call musb_start() only once in OTG mode)
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org> # v3.11+
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
