| Age | Commit message (Collapse) | Author |
|---|
|
Enabling linestate wake up is causing spurious wake up
on deep sleep. Disable it till root caused.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Explicitly set and clear wakeup config so we don't leave anything
to chance.
Clear wakeup status on suspend so we know what caused wake up.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
USB module can wakeup system. Enable it as a wakeup source
by default. Finer grain wakeup enable/disable can be done
from the power/wakeup system control file of the respective
USB device.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-5.10.y-cicd
This is the 5.10.168 stable release
* tag 'v5.10.168' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (286 commits)
Linux 5.10.168
Fix page corruption caused by racy check in __free_pages
arm64: dts: meson-axg: Make mmc host controller interrupts level-sensitive
arm64: dts: meson-g12-common: Make mmc host controller interrupts level-sensitive
arm64: dts: meson-gx: Make mmc host controller interrupts level-sensitive
riscv: Fixup race condition on PG_dcache_clean in flush_icache_pte
ceph: flush cap releases when the session is flushed
usb: typec: altmodes/displayport: Fix probe pin assign check
usb: core: add quirk for Alcor Link AK9563 smartcard reader
btrfs: free device in btrfs_close_devices for a single device filesystem
net: USB: Fix wrong-direction WARNING in plusb.c
cifs: Fix use-after-free in rdata->read_into_pages()
pinctrl: intel: Restore the pins that used to be in Direct IRQ mode
spi: dw: Fix wrong FIFO level setting for long xfers
pinctrl: single: fix potential NULL dereference
pinctrl: aspeed: Fix confusing types in return value
ALSA: pci: lx6464es: fix a debug loop
selftests: forwarding: lib: quote the sysctl values
rds: rds_rm_zerocopy_callback() use list_first_entry()
net/mlx5: fw_tracer, Zero consumer index when reloading the tracer
...
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-5.10.y-cicd
This is the 5.10.165 stable release
* tag 'v5.10.165' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (951 commits)
Linux 5.10.165
io_uring/rw: remove leftover debug statement
io_uring/rw: ensure kiocb_end_write() is always called
io_uring: fix double poll leak on repolling
io_uring: Clean up a false-positive warning from GCC 9.3.0
mm/khugepaged: fix collapse_pte_mapped_thp() to allow anon_vma
Bluetooth: hci_qca: Fixed issue during suspend
Bluetooth: hci_qca: check for SSR triggered flag while suspend
Bluetooth: hci_qca: Wait for SSR completion during suspend
soc: qcom: apr: Make qcom,protection-domain optional again
Revert "wifi: mac80211: fix memory leak in ieee80211_if_add()"
net/mlx5: fix missing mutex_unlock in mlx5_fw_fatal_reporter_err_work()
net/ulp: use consistent error code when blocking ULP
io_uring/net: fix fast_iov assignment in io_setup_async_msg()
io_uring: io_kiocb_update_pos() should not touch file for non -1 offset
tracing: Use alignof__(struct {type b;}) instead of offsetof()
x86/fpu: Use _Alignof to avoid undefined behavior in TYPE_ALIGN
Revert "drm/amdgpu: make display pinning more flexible (v2)"
efi: rt-wrapper: Add missing include
arm64: efi: Execute runtime services from a dedicated stack
...
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
# Conflicts:
# net/hsr/hsr_device.c
# net/hsr/hsr_forward.c
|
|
commit 54e5c00a4eb0a4c663445b245f641bbfab142430 upstream.
While checking Pin Assignments of the port and partner during probe, we
don't take into account whether the peripheral is a plug or receptacle.
This manifests itself in a mode entry failure on certain docks and
dongles with captive cables. For instance, the Startech.com Type-C to DP
dongle (Model #CDP2DP) advertises its DP VDO as 0x405. This would fail
the Pin Assignment compatibility check, despite it supporting
Pin Assignment C as a UFP.
Update the check to use the correct DP Pin Assign macros that
take the peripheral's receptacle bit into account.
Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Reported-by: Diana Zigterman <dzigterman@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20230208205318.131385-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 303e724d7b1e1a0a93daf0b1ab5f7c4f53543b34 upstream.
The Alcor Link AK9563 smartcard reader used on some Lenovo platforms
doesn't work. If LPM is enabled the reader will provide an invalid
usb config descriptor. Added quirk to disable LPM.
Verified fix on Lenovo P16 G1 and T14 G3
Tested-by: Miroslav Zatko <mzatko@mirexoft.com>
Tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230208181223.1092654-1-mpearson-lenovo@squebb.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 921deb9da15851425ccbb6ee409dc2fd8fbdfe6b ]
__ffs_ep0_queue_wait executes holding the spinlock of &ffs->ev.waitq.lock
and unlocks it after the assignments to usb_request are done.
However in the code if the request is already NULL we bail out returning
-EINVAL but never unlocked the spinlock.
Fix this by adding spin_unlock_irq &ffs->ev.waitq.lock before returning.
Fixes: 6a19da111057 ("usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait")
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/20230124091149.18647-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eb320f76e31dc835b9f57f04af1a2353b13bb7d8 ]
With vbus override enabled when in OTG dr_mode, Host<->Peripheral
switch now works on SM8550, otherwise the DWC3 seems to be stuck
in Host mode only.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230123-topic-sm8550-upstream-dwc3-qcom-otg-v2-1-2d400e598463@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8e6cb5d27e8246d9c986ec162d066a502d2b602b ]
There was an extra character in the dwc3_qcom_vbus_override_enable()
function. Removed the extra character.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210704013314.200951-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: eb320f76e31d ("usb: dwc3: qcom: enable vbus override when in OTG dr-mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b7a4f9b5d0e4b6dd937678c546c0b322dd1a4054 upstream.
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd() if xhci has two roothubs.
This will make sure both primary roothub and secondary roothub will be
registered along with the second HCD.
This is required for cold plugged USB devices to be detected in certain
PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM).
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
[minor rebase change, and commit message update -Mathias]
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-3-kishon@ti.com
Signed-off-by: Adrian Zaharia <Adrian.Zaharia@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce405d561b020e5a46340eb5146805a625dcacee ]
As per the documentation, function usb_ep_free_request guarantees
the request will not be queued or no longer be re-queued (or
otherwise used). However, with the current implementation it
doesn't make sure that the request in ep0 isn't reused.
Fix this by dequeuing the ep0req on functionfs_unbind before
freeing the request to align with the definition.
Fixes: ddf8abd25994 ("USB: f_fs: the FunctionFS driver")
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Tested-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20221215052906.8993-3-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6a19da111057f69214b97c62fb0ac59023970850 ]
While performing fast composition switch, there is a possibility that the
process of ffs_ep0_write/ffs_ep0_read get into a race condition
due to ep0req being freed up from functionfs_unbind.
Consider the scenario that the ffs_ep0_write calls the ffs_ep0_queue_wait
by taking a lock &ffs->ev.waitq.lock. However, the functionfs_unbind isn't
bounded so it can go ahead and mark the ep0req to NULL, and since there
is no NULL check in ffs_ep0_queue_wait we will end up in use-after-free.
Fix this by making a serialized execution between the two functions using
a mutex_lock(ffs->mutex).
Fixes: ddf8abd25994 ("USB: f_fs: the FunctionFS driver")
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Tested-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20221215052906.8993-2-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux into ti-linux-5.10.y-cicd
This is the 5.10.162 stable release
* tag 'v5.10.162' of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux: (198 commits)
Linux 5.10.162
io_uring: pass in EPOLL_URING_WAKE for eventfd signaling and wakeups
eventfd: provide a eventfd_signal_mask() helper
eventpoll: add EPOLL_URING_WAKE poll wakeup flag
Revert "proc: don't allow async path resolution of /proc/self components"
Revert "proc: don't allow async path resolution of /proc/thread-self components"
net: remove cmsg restriction from io_uring based send/recvmsg calls
task_work: unconditionally run task_work from get_signal()
signal: kill JOBCTL_TASK_WORK
io_uring: import 5.15-stable io_uring
task_work: add helper for more targeted task_work canceling
kernel: don't call do_exit() for PF_IO_WORKER threads
kernel: stop masking signals in create_io_thread()
x86/process: setup io_threads more like normal user space threads
arch: ensure parisc/powerpc handle PF_IO_WORKER in copy_thread()
arch: setup PF_IO_WORKER threads like PF_KTHREAD
entry/kvm: Exit to user mode when TIF_NOTIFY_SIGNAL is set
kernel: allow fork with TIF_NOTIFY_SIGNAL pending
coredump: Limit what can interrupt coredumps
kernel: remove checking for TIF_NOTIFY_SIGNAL
...
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
commit dbd24ec17b85b45f4e823d1aa5607721920f2b05 upstream.
The commit e00b488e813f ("usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS")
blacklists UAS for all of RTL9210 enclosures.
The RTL9210 controller was advertised with UAS since its release back in
2019 and was shipped with a lot of enclosure products with different
firmware combinations.
Blacklist UAS only for HIKSEMI MD202.
This should hopefully be replaced with more robust method than just
comparing strings. But with limited information [1] provided thus far
(dmesg when the device is plugged in, which includes manufacturer and
product, but no lsusb -v to compare against), this is the best we can do
for now.
[1] https://lore.kernel.org/all/20230109115550.71688-1-qkrwngud825@gmail.com
Fixes: e00b488e813f ("usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS")
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Hongling Zeng <zenghongling@kylinos.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Juhyung Park <qkrwngud825@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20230117085154.123301-1-qkrwngud825@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c6ec929595c7443250b2a4faea988c62019d5cd2 upstream.
In Google internal bug 265639009 we've received an (as yet) unreproducible
crash report from an aarch64 GKI 5.10.149-android13 running device.
AFAICT the source code is at:
https://android.googlesource.com/kernel/common/+/refs/tags/ASB-2022-12-05_13-5.10
The call stack is:
ncm_close() -> ncm_notify() -> ncm_do_notify()
with the crash at:
ncm_do_notify+0x98/0x270
Code: 79000d0b b9000a6c f940012a f9400269 (b9405d4b)
Which I believe disassembles to (I don't know ARM assembly, but it looks sane enough to me...):
// halfword (16-bit) store presumably to event->wLength (at offset 6 of struct usb_cdc_notification)
0B 0D 00 79 strh w11, [x8, #6]
// word (32-bit) store presumably to req->Length (at offset 8 of struct usb_request)
6C 0A 00 B9 str w12, [x19, #8]
// x10 (NULL) was read here from offset 0 of valid pointer x9
// IMHO we're reading 'cdev->gadget' and getting NULL
// gadget is indeed at offset 0 of struct usb_composite_dev
2A 01 40 F9 ldr x10, [x9]
// loading req->buf pointer, which is at offset 0 of struct usb_request
69 02 40 F9 ldr x9, [x19]
// x10 is null, crash, appears to be attempt to read cdev->gadget->max_speed
4B 5D 40 B9 ldr w11, [x10, #0x5c]
which seems to line up with ncm_do_notify() case NCM_NOTIFY_SPEED code fragment:
event->wLength = cpu_to_le16(8);
req->length = NCM_STATUS_BYTECOUNT;
/* SPEED_CHANGE data is up/down speeds in bits/sec */
data = req->buf + sizeof *event;
data[0] = cpu_to_le32(ncm_bitrate(cdev->gadget));
My analysis of registers and NULL ptr deref crash offset
(Unable to handle kernel NULL pointer dereference at virtual address 000000000000005c)
heavily suggests that the crash is due to 'cdev->gadget' being NULL when executing:
data[0] = cpu_to_le32(ncm_bitrate(cdev->gadget));
which calls:
ncm_bitrate(NULL)
which then calls:
gadget_is_superspeed(NULL)
which reads
((struct usb_gadget *)NULL)->max_speed
and hits a panic.
AFAICT, if I'm counting right, the offset of max_speed is indeed 0x5C.
(remember there's a GKI KABI reservation of 16 bytes in struct work_struct)
It's not at all clear to me how this is all supposed to work...
but returning 0 seems much better than panic-ing...
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Carlos Llamas <cmllamas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230117131839.1138208-1-maze@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e95765e97d9cb93258a4840440d410fa6ff7e819 upstream.
Currently the color matching descriptor is only sent across the wire
a single time, following the descriptors for each format and frame.
According to the UVC 1.5 Specification 3.9.2.6 ("Color Matching
Descriptors"):
"Only one instance is allowed for a given format and if present,
the Color Matching descriptor shall be placed following the Video
and Still Image Frame descriptors for that format".
Add another reference to the color matching descriptor after the
yuyv frames so that it's correctly transmitted for that format
too.
Fixes: a9914127e834 ("USB gadget: Webcam device")
Cc: stable <stable@kernel.org>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/20221216160528.479094-1-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9682b41e52cc9f42f5c33caf410464392adaef04 upstream.
Commit c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin
assignment for UFP receptacles") fixed the pin assignment calculation
to take into account whether the peripheral was a plug or a receptacle.
But the "pin_assignments" sysfs logic was not updated. Address this by
using the macros introduced in the aforementioned commit in the sysfs
logic too.
Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230111020546.3384569-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 582836e3cfab4faafbdc93bbec96fce036a08ee1 upstream.
The code to extract a peripheral's currently supported Pin Assignments
is repeated in a couple of locations. Factor it out into a separate
function.
This will also make it easier to add fixes (we only need to update 1
location instead of 2).
Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230111020546.3384569-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d3d01ae15d2f37ed0325c99ab47ef0ae5d05f3c upstream.
Commit ca07e1c1e4a6 ("drivers:usb:fsl:Make fsl ehci drv an independent
driver module") changed DRV_NAME which was used for MODULE_ALIAS as well.
Starting from this the module alias didn't match the platform device
name created in fsl-mph-dr-of.c
Change DRV_NAME to match the driver name for host mode in fsl-mph-dr-of.
This is needed for module autoloading on ls1021a.
Fixes: ca07e1c1e4a6 ("drivers:usb:fsl:Make fsl ehci drv an independent driver module")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230120122714.3848784-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f9e76e31704a325170e5aec2243c8d084d74854 upstream.
Add the USB serial console device ID for Siemens SCALANCE LPE-9000
which have a USB port for their serial console.
Signed-off-by: Michael Adler <michael.adler@siemens.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d18dcfe9860e842f394e37ba01ca9440ab2178f4 upstream.
The syzbot fuzzer and Gerald Lee have identified a use-after-free bug
in the gadgetfs driver, involving processes concurrently mounting and
unmounting the gadgetfs filesystem. In particular, gadgetfs_fill_super()
can race with gadgetfs_kill_sb(), causing the latter to deallocate
the_device while the former is using it. The output from KASAN says,
in part:
BUG: KASAN: use-after-free in instrument_atomic_read_write include/linux/instrumented.h:102 [inline]
BUG: KASAN: use-after-free in atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
BUG: KASAN: use-after-free in __refcount_sub_and_test include/linux/refcount.h:272 [inline]
BUG: KASAN: use-after-free in __refcount_dec_and_test include/linux/refcount.h:315 [inline]
BUG: KASAN: use-after-free in refcount_dec_and_test include/linux/refcount.h:333 [inline]
BUG: KASAN: use-after-free in put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
BUG: KASAN: use-after-free in gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
Write of size 4 at addr ffff8880276d7840 by task syz-executor126/18689
CPU: 0 PID: 18689 Comm: syz-executor126 Not tainted 6.1.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
...
atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
__refcount_sub_and_test include/linux/refcount.h:272 [inline]
__refcount_dec_and_test include/linux/refcount.h:315 [inline]
refcount_dec_and_test include/linux/refcount.h:333 [inline]
put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
deactivate_locked_super+0xa7/0xf0 fs/super.c:332
vfs_get_super fs/super.c:1190 [inline]
get_tree_single+0xd0/0x160 fs/super.c:1207
vfs_get_tree+0x88/0x270 fs/super.c:1531
vfs_fsconfig_locked fs/fsopen.c:232 [inline]
The simplest solution is to ensure that gadgetfs_fill_super() and
gadgetfs_kill_sb() are serialized by making them both acquire a new
mutex.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+33d7ad66d65044b93f16@syzkaller.appspotmail.com
Reported-and-tested-by: Gerald Lee <sundaywind2004@gmail.com>
Link: https://lore.kernel.org/linux-usb/CAO3qeMVzXDP-JU6v1u5Ags6Q-bb35kg3=C6d04DjzA9ffa5x1g@mail.gmail.com/
Fixes: e5d82a7360d1 ("vfs: Convert gadgetfs to use the new mount API")
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Y6XCPXBpn3tmjdCC@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7171b0e261b17de96490adf053b8bb4b00061bcf upstream.
The Texas Instruments TUSB8041 has an autosuspend problem at high
temperature.
If there is not USB traffic, after a couple of ms, the device enters in
autosuspend mode. In this condition the external clock stops working, to
save energy. When the USB activity turns on, ther hub exits the
autosuspend state, the clock starts running again and all works fine.
At ambient temperature all works correctly, but at high temperature,
when the USB activity turns on, the external clock doesn't restart and
the hub disappears from the USB bus.
Disabling the autosuspend mode for this hub solves the issue.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20221219124759.3207032-1-f.suligoi@asem.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 14ff7460bb58662d86aa50298943cc7d25532e28 upstream.
The USB_DEVICE_ID_CODEMERCS_IOW100 header size was incorrect, it should
be 12, not 13.
Cc: stable <stable@kernel.org>
Fixes: 17a82716587e ("USB: iowarrior: fix up report size handling for some devices")
Reported-by: Christoph Jung <jung@codemercs.com>
Link: https://lore.kernel.org/r/20230120135330.3842518-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71dfd381a7c051f16a61f82fbd38a4cca563bdca upstream.
The EM05CN modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"MBIM" : AT + MBIM + DIAG + NMEA + MODEM
"RMNET" : AT + DIAG + NMEA + Modem + QMI
The detailed description of the USB configuration for each mode as follows:
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0312 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-CN
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 1 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 2 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0312 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-CN
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1541dd0097c0f8f470e76eddf5120fc55a7e3101 upstream.
The EM05CN (SG) modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"MBIM" : AT + MBIM + DIAG + NMEA + MODEM
"RMNET" : AT + DIAG + NMEA + Modem + QMI
The detailed description of the USB configuration for each mode as follows:
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0310 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-CN
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 1 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 2 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0310 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-CN
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9bbb15881046bd76f8710c76e26a740eee997ef upstream.
Add support for EC200U modem
0x0901: EC200U - AT + AP + CP + NMEA + DIAG + MOS
usb-device output:
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0901 Rev= 3.18
S: Manufacturer=Android
S: Product=Android
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=400mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 512 Ivl=4096ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 512 Ivl=4096ms
I:* If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Ali Mirghasemi <ali.mirghasemi1376@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b72d13977689f0c717444010e108c4f20658dfee upstream.
The EM05-G (RS) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0314 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0314 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb78654b0b46316dac687fd4b7dc7cce636f46cd upstream.
The EM05-G (CS) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030C Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030C Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c331f32e32ac71eb3e8b93fceda2802d7ecb889 upstream.
The EM05-G (GR) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0313 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0313 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74622f0a81d0c2bcfc39f9192b788124e8c7f0af upstream.
USB3 ports on xHC hosts may have retimers that cause too long
exit latency to work with native USB3 U1/U2 link power management states.
For now only use usb_acpi_port_lpm_incapable() to evaluate if port lpm
should be disabled while setting up the USB3 roothub.
Other ways to identify lpm incapable ports can be added here later if
ACPI _DSM does not exist.
Limit this to Intel hosts for now, this is to my knowledge only
an Intel issue.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd702d18c882d5a4ea44bbdb38edd5d5577ef640 upstream.
Add a helper to evaluate ACPI usb device specific method (_DSM) provided
in case the USB3 port shouldn't enter U1 and U2 link states.
This _DSM was added as port specific retimer configuration may lead to
exit latencies growing beyond U1/U2 exit limits, and OS needs a way to
find which ports can't support U1/U2 link power management states.
This _DSM is also used by windows:
Link: https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/usb-device-specific-method---dsm-
Some patch issues found in testing resolved by Ron Lee
Cc: stable@vger.kernel.org
Tested-by: Ron Lee <ron.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0522b9a1653048440da5f21747f21e498b9220d1 upstream.
One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23a3b8d5a2365653fd9bc5a9454d1e7f4facbf85 upstream.
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a2bc47c43e70cf904b1af49f76d572326c08bca7 upstream.
Make sure xhci_free_dev() and xhci_kill_endpoint_urbs() do not race
and cause null pointer dereference when host suddenly dies.
Usb core may call xhci_free_dev() which frees the xhci->devs[slot_id]
virt device at the same time that xhci_kill_endpoint_urbs() tries to
loop through all the device's endpoints, checking if there are any
cancelled urbs left to give back.
hold the xhci spinlock while freeing the virt device
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8fb5bc76eb86437ab87002d4a36d6da02165654 upstream.
When the host controller is not responding, all URBs queued to all
endpoints need to be killed. This can cause a kernel panic if we
dereference an invalid endpoint.
Fix this by using xhci_get_virt_ep() helper to find the endpoint and
checking if the endpoint is valid before dereferencing it.
[233311.853271] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead
[233311.853393] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
[233311.853964] pc : xhci_hc_died+0x10c/0x270
[233311.853971] lr : xhci_hc_died+0x1ac/0x270
[233311.854077] Call trace:
[233311.854085] xhci_hc_died+0x10c/0x270
[233311.854093] xhci_stop_endpoint_command_watchdog+0x100/0x1a4
[233311.854105] call_timer_fn+0x50/0x2d4
[233311.854112] expire_timers+0xac/0x2e4
[233311.854118] run_timer_softirq+0x300/0xabc
[233311.854127] __do_softirq+0x148/0x528
[233311.854135] irq_exit+0x194/0x1a8
[233311.854143] __handle_domain_irq+0x164/0x1d0
[233311.854149] gic_handle_irq.22273+0x10c/0x188
[233311.854156] el1_irq+0xfc/0x1a8
[233311.854175] lpm_cpuidle_enter+0x25c/0x418 [msm_pm]
[233311.854185] cpuidle_enter_state+0x1f0/0x764
[233311.854194] do_idle+0x594/0x6ac
[233311.854201] cpu_startup_entry+0x7c/0x80
[233311.854209] secondary_start_kernel+0x170/0x198
Fixes: 50e8725e7c42 ("xhci: Refactor command watchdog and fix split string.")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <0fe978ed-8269-9774-1c40-f8a98c17e838@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93915a4170e9defd56a767a18e6c4076f3d18609 upstream.
Allow devices to have dma operations beyond 64K, and avoid warnings such
as:
xhci_hcd 0000:00:14.0: mapping sg segment longer than device claims to support [len=98304] [max=65536]
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b659b613cea2ae39746ca8bd2b69d1985dd9d770 upstream.
This reverts commit 8a7b31d545d3a15f0e6f5984ae16f0ca4fd76aac.
This patch results in some qemu test failures, specifically xilinx-zynq-a9
machine and zynq-zc702 as well as zynq-zed devicetree files, when trying
to boot from USB drive.
Link: https://lore.kernel.org/lkml/20221220194334.GA942039@roeck-us.net/
Fixes: 8a7b31d545d3 ("usb: ulpi: defer ulpi_register on ulpi_read_id timeout")
Cc: stable@vger.kernel.org
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221222205302.45761-1-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8a7b31d545d3a15f0e6f5984ae16f0ca4fd76aac ]
Since commit 0f0101719138 ("usb: dwc3: Don't switch OTG -> peripheral
if extcon is present") Dual Role support on Intel Merrifield platform
broke due to rearranging the call to dwc3_get_extcon().
It appears to be caused by ulpi_read_id() on the first test write failing
with -ETIMEDOUT. Currently ulpi_read_id() expects to discover the phy via
DT when the test write fails and returns 0 in that case, even if DT does not
provide the phy. As a result usb probe completes without phy.
Make ulpi_read_id() return -ETIMEDOUT to its user if the first test write
fails. The user should then handle it appropriately. A follow up patch
will make dwc3_core_init() set -EPROBE_DEFER in this case and bail out.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221205201527.13525-2-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a1575120972ecd7baa6af6a69e4e7ea9213bde7c ]
Make sure to also limit the amount of soft reset retries for transaction
errors on streams in cases where the transaction error event doesn't point
to any specific TRB.
In these cases we don't know the TRB or stream ring, but we do know which
endpoint had the error.
To keep error counting simple and functional, move the current err_count
from ring structure to endpoint structure.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c6c334e6fc8cd99e780fd74cd29687886a81862 ]
Halted endpoints can be discoverd both when handling transfer events and
command completion events. Move code that handles halted endpoints before
both of those event handlers.
Rename the function to xhci_handle_halted_ep() to better describe
what it does. Try to reserve "cleanup" word in function names for last
stage cleanup activities.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a1575120972e ("xhci: Prevent infinite loop in transaction errors recovery for streams")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a6ccd1fd4bd4fca37eaa3d76bef940d6332919bc ]
In cases where the TD can't be given back in current handler we want
to be able to store it until its time to return the TD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a1575120972e ("xhci: Prevent infinite loop in transaction errors recovery for streams")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69eaf9e79fa7c7ff4b1eb626493ce5a81e467520 ]
No funtional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a1575120972e ("xhci: Prevent infinite loop in transaction errors recovery for streams")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8ac95001bea683d2088acb3e61613a27b8d2d5f ]
Create a separate helper function to issue reset endpont commands
to clear halted endpoints.
This is useful for cases where a halted endpoint is discovered while
completing another command, and the endpoint halt needs to be cleared
with a endpoint reset first.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a1575120972e ("xhci: Prevent infinite loop in transaction errors recovery for streams")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d70f4231b81eeb6dd78bd913ff42729b524eec51 ]
Instead of passing slot id and endpoint index to
cleanup_halted_endpoint() pass the endpoint structure pointer
as it's already known.
Avoids again digging out the endpoint structure based on
slot id and endpoint index, and passing them along the
call chain for this purpose only.
Add slot_id to the virt_dev structure so that it
can easily be found from a virt_dev, or its child, the
virt_ep endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a1575120972e ("xhci: Prevent infinite loop in transaction errors recovery for streams")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d4dff8043ea5b93a30cb9b19d4407bd506a6877a ]
isochronous endpoints do not support streams, meaning that
there is only one ring per endpoint.
Avoid double-fetching the transfer event DMA to get the
ring. Also makes passing the event to skip_isoc_td() uncecessary.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a1575120972e ("xhci: Prevent infinite loop in transaction errors recovery for streams")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ab58f3bb6aaaf98ba81d5c627ac25c08ff4ed4f1 ]
When handling transfer events the event is passed along the handling
callpath and parsed again in several occasions.
The event contains slot_id and endpoint index, from which the driver
endpoint structure can be found. There wasn't however a way to get the
endpoint index or parent usb device from this endpoint structure.
A lot of extra event parsing, and thus some DMA doublefetch cases,
and excess variables and code can be avoided by adding endpoint index
and parent usb virt device pointer to the endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a1575120972e ("xhci: Prevent infinite loop in transaction errors recovery for streams")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 97a48da1619ba6bd42a0e5da0a03aa490a9496b1 ]
of_icc_get() alloc resources for path handle, we should release it when not
need anymore. Like the release in dwc3_qcom_interconnect_exit() function.
Add icc_put() in error handling to fix this.
Fixes: bea46b981515 ("usb: dwc3: qcom: Add interconnect support in dwc3 driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20221206081731.818107-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 63130462c919ece0ad0d9bb5a1f795ef8d79687e upstream.
Since commit 0f0101719138 ("usb: dwc3: Don't switch OTG -> peripheral
if extcon is present"), Dual Role support on Intel Merrifield platform
broke due to rearranging the call to dwc3_get_extcon().
It appears to be caused by ulpi_read_id() masking the timeout on the first
test write. In the past dwc3 probe continued by calling dwc3_core_soft_reset()
followed by dwc3_get_extcon() which happend to return -EPROBE_DEFER.
On deferred probe ulpi_read_id() finally succeeded. Due to above mentioned
rearranging -EPROBE_DEFER is not returned and probe completes without phy.
On Intel Merrifield the timeout on the first test write issue is reproducible
but it is difficult to find the root cause. Using a mainline kernel and
rootfs with buildroot ulpi_read_id() succeeds. As soon as adding
ftrace / bootconfig to find out why, ulpi_read_id() fails and we can't
analyze the flow. Using another rootfs ulpi_read_id() fails even without
adding ftrace. We suspect the issue is some kind of timing / race, but
merely retrying ulpi_read_id() does not resolve the issue.
As we now changed ulpi_read_id() to return -ETIMEDOUT in this case, we
need to handle the error by calling dwc3_core_soft_reset() and request
-EPROBE_DEFER. On deferred probe ulpi_read_id() is retried and succeeds.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221205201527.13525-3-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62c73bfea048e66168df09da6d3e4510ecda40bb upstream.
dwc->desired_dr_role is changed by dwc3_set_mode inside a spinlock but
then read by __dwc3_set_mode outside of that lock. This can lead to a
race condition when very quick successive role switch events happen:
CPU A
dwc3_set_mode(DWC3_GCTL_PRTCAP_HOST) // first role switch event
spin_lock_irqsave(&dwc->lock, flags);
dwc->desired_dr_role = mode; // DWC3_GCTL_PRTCAP_HOST
spin_unlock_irqrestore(&dwc->lock, flags);
queue_work(system_freezable_wq, &dwc->drd_work);
CPU B
__dwc3_set_mode
// ....
spin_lock_irqsave(&dwc->lock, flags);
// desired_dr_role is DWC3_GCTL_PRTCAP_HOST
dwc3_set_prtcap(dwc, dwc->desired_dr_role);
spin_unlock_irqrestore(&dwc->lock, flags);
CPU A
dwc3_set_mode(DWC3_GCTL_PRTCAP_DEVICE) // second event
spin_lock_irqsave(&dwc->lock, flags);
dwc->desired_dr_role = mode; // DWC3_GCTL_PRTCAP_DEVICE
spin_unlock_irqrestore(&dwc->lock, flags);
CPU B (continues running __dwc3_set_mode)
switch (dwc->desired_dr_role) { // DWC3_GCTL_PRTCAP_DEVICE
// ....
case DWC3_GCTL_PRTCAP_DEVICE:
// ....
ret = dwc3_gadget_init(dwc);
We then have DWC3_GCTL.DWC3_GCTL_PRTCAPDIR = DWC3_GCTL_PRTCAP_HOST and
dwc->current_dr_role = DWC3_GCTL_PRTCAP_HOST but initialized the
controller in device mode. It's also possible to get into a state
where both host and device are intialized at the same time.
Fix this race by creating a local copy of desired_dr_role inside
__dwc3_set_mode while holding dwc->lock.
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20221128161526.79730-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
