| Age | Commit message (Collapse) | Author |
|---|
|
commit 671b4b2ba9266cbcfe7210a704e9ea487dcaa988 upstream.
Many cards based on CY7C68300A/B/C use the USB ID 04b4:6830 but only the
B and C variants (EZ-USB AT2LP) support the ATA Command Block
functionality, according to the data sheets. The A variant (EZ-USB AT2)
locks up if ATACB is attempted, until a typical 30 seconds timeout runs
out and a USB reset is performed.
https://bugs.launchpad.net/bugs/428469
It seems that one way to spot a CY7C68300A (at least where the card
manufacturer left Cypress' EEPROM default vaules, against Cypress'
recommendations) is to look at the USB string descriptor indices.
A http://media.digikey.com/pdf/Data%20Sheets/Cypress%20PDFs/CY7C68300A.pdf
B http://www.farnell.com/datasheets/43456.pdf
C http://www.cypress.com/?rID=14189
Note that a CY7C68300B/C chip appears as CY7C68300A if it is running
in Backward Compatibility Mode, and if ATACB would be supported in this
case there is anyway no way to tell which chip it really is.
For 5 years my external USB drive has been locking up for half a minute
when plugged in and ata_id is run by udev, or anytime hdparm or similar
is run on it.
Finally looking at the /correct/ datasheet I think I found the reason. I
am aware the quirk in this patch is a bit hacky, but the hardware
manufacturers haven't made it easy for us.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61ac6ac8d662ac7ac67c864954d39d1b19948354 upstream.
We remove the redundant tdi_reset in ehci_setup since there
is already it in ehci_reset.
It was observed that the duplicated tdi_reset was causing
the PHY_CLK_VALID bit unstable.
Reported-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ca2cd291fd84ae499390f227a255ccba2780a81 upstream.
In hardware_enqueue code adds one extra td with dma_pool_alloc if
mReq->req.zero is true. When _ep_nuke will be called for that endpoint,
dma_pool_free will not be called to free that memory again. That patch
fixes this.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9c174302b1590ef3ead485d804a303c5f89174b upstream.
The udc uses an shared dma memory space between hard and software. This
memory layout is described in ci13xxx_qh and ci13xxx_td which are marked
with the attribute ((packed)).
The compiler currently does not know about the alignment of the memory
layout, and will create strb and ldrb operations.
The Datasheet of the synopsys core describes, that some operations on
the mapped memory need to be atomic double word operations. I.e. the
next pointer addressing in the qhead, as otherwise the hardware will
read wrong data and totally stuck.
This is also possible while working with the current active td queue,
and preparing the td->ptr.next in software while the hardware is still
working with the current active td which is supposed to be changed:
writeb(0xde, &td->ptr.next + 0x0); /* strb */
writeb(0xad, &td->ptr.next + 0x1); /* strb */
<----- hardware reads value of td->ptr.next and get stuck!
writeb(0xbe, &td->ptr.next + 0x2); /* strb */
writeb(0xef, &td->ptr.next + 0x3); /* strb */
This appeares on armv5 machines where the hardware does not support
unaligned 32bit operations.
This patch adds the attribute ((aligned(4))) to the structures to tell
the compiler to use 32bit operations. It also adds an wmb() for the
prepared TD data before it gets enqueued into the qhead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1361bf4b9f9ef45e628a5b89e0fd9bedfdcb7104 upstream.
When usbfs receives a ctrl-request from userspace it calls check_ctrlrecip,
which for a request with USB_RECIP_ENDPOINT tries to map this to an interface
to see if this interface is claimed, except for ctrl-requests with a type of
USB_TYPE_VENDOR.
When trying to use this device: http://www.akaipro.com/eiepro
redirected to a Windows vm running on qemu on top of Linux.
The windows driver makes a ctrl-req with USB_TYPE_CLASS and
USB_RECIP_ENDPOINT with index 0, and the mapping of the endpoint (0) to
the interface fails since ep 0 is the ctrl endpoint and thus never is
part of an interface.
This patch fixes this ctrl-req failing by skipping the checkintf call for
USB_RECIP_ENDPOINT ctrl-reqs on the ctrl endpoint.
Reported-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl>
Tested-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b6fd35ee5766143d6bc3c333edf374c336ebdca6 upstream.
Fix regression introduced by commit f40d78155 ("USB: io_ti: kill custom
closing_wait implementation") which made TIOCGSERIAL return the wrong
value for closing_wait.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71d9a2b95fc9c9474d46d764336efd7a5a805555 upstream.
The FT4232H used in the ST Micro Connect Lite has four hi-speed UART ports.
The first two ports are reserved for the JTAG interface.
We enable by default ports 2 and 3 as UARTs (where port 2 is a
conventional RS-232 UART)
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f06d15f8db6946e41f73196a122b84a37938878 upstream.
The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.
For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58f8b6c4fa5a13cb2ddb400e26e9e65766d71e38 upstream.
This patch add a missing usb device id for the GDMBoost V1.x device
The patch is against 3.9-rc5
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7d3b6e22c871ba36d052ca99bc8ceca4d546a60 upstream.
Add the Apple 24" LED Cinema display to the supported devices.
Signed-off-by: Ben Jencks <ben@bjencks.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a2a2d6c7f93e160b52a4ad0164db1f43f743ae0f upstream.
Adding support for a Mediatek based device labelled as
D-Link Model: DWM-156, H/W Ver: A7
Also adding two other device IDs found in the Debian(!)
packages included on the embedded device driver CD.
This is a composite MBIM + serial ports + card reader device:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2001 ProdID=7d01 Rev= 3.00
S: Manufacturer=D-Link,Inc
S: Product=D-Link DWM-156
C:* #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=88(I) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=500us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d19bf5cedfd7d53854a3bd699c98b467b139833b upstream.
This adds PID for Olivetti Olicard 145 in option.c
Signed-off-by: Filippo Turato <nnj7585@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the call to dev_pm_qos_hide_flags(), added by commit 6e30d7cb
"usb: Add driver/usb/core/(port.c,hub.h) files", from
usb_port_device_release(), because (1) it is completely unnecessary
(the flags have been removed already by the PM core during the
unregistration of the device object) and (2) it triggers a NULL
pointer dereference in sysfs_find_dirent() (dev->kobj.sd is NULL at
this point).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It enhances the driver for FTDI-based USB serial adapters
to recognize Mitsubishi Electric Corp. USB/RS422 Converters
as FT232BM chips and support them.
https://search.meau.com/?q=FX-USB-AW
Signed-off-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Tested-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current lpc32xx_defconfig breaks like this, caused by recent phy
restructuring:
LD init/built-in.o
drivers/built-in.o: In function `usb_hcd_nxp_probe':
drivers/usb/host/ohci-nxp.c:224: undefined reference to `isp1301_get_client'
drivers/built-in.o: In function `lpc32xx_udc_probe':
drivers/usb/gadget/lpc32xx_udc.c:3104: undefined reference to
`isp1301_get_client' distcc[27867] ERROR: compile (null) on localhost failed
make: *** [vmlinux] Error 1
Caused by 1c2088812f095df77f4b3224b65db79d7111a300 (usb: Makefile: fix
drivers/usb/phy/ Makefile entry)
This patch fixes this by selecting USB_OTG_UTILS in Kconfig which
causes the phy driver to be built again.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Misc xHCI fixes for 3.9
Hi Greg,
Here's a couple of fixes for the xHCI driver. Three patches are nothing
major: build warning fix, macro field width fix, and removing some
unnecessary log spam.
The only interesting thing here is Tianyu's two patches to fix the USB
port connection type discovery, for the USB port power off mechanism.
This adds new USB host API, but as discussed, it's necessary to avoid
powering off the wrong USB port. It's not marked for backport to stable
kernels, since the sysfs mechanism to manually power off a port didn't
go in until 3.9.
I've smoke tested these, including system suspend, USB device suspend,
and rocking out in my cube with a pair of USB headphones. They look
fine to me.
Hibernate is currently broken on my system, due to some nouveau MMIO
read faults. I'll report that separately.
Sarah Sharp
|
|
Johan's 'fix use-after-free in TIOCMIWAIT' patchset[1] introduces
one bug which can cause kernel hang when opening port.
This patch initialized the 'port->delta_msr_wait' waitqueue head
to fix the bug which is introduced in 3.9-rc4.
[1], http://marc.info/?l=linux-usb&m=136368139627876&w=2
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[Description written by Alan Stern]
Soeren tracked down a very difficult bug in ehci-hcd's DMA pool
management of iTD and siTD structures. Some background: ehci-hcd
gives each isochronous endpoint its own set of active and free itd's
(or sitd's for full-speed devices). When a new itd is needed, it is
taken from the head of the free list, if possible. However, itd's
must not be used twice in a single frame because the hardware
continues to access the data structure for the entire duration of a
frame. Therefore if the itd at the head of the free list has its
"frame" member equal to the current value of ehci->now_frame, it
cannot be reused and instead a new itd is allocated from the DMA pool.
The entries on the free list are not released back to the pool until
the endpoint is no longer in use.
The bug arises from the fact that sometimes an itd can be moved back
onto the free list before itd->frame has been set properly. In
Soeren's case, this happened because ehci-hcd can allocate one more
itd than it actually needs for an URB; the extra itd may or may not be
required depending on how the transfer aligns with a frame boundary.
For example, an URB with 8 isochronous packets will cause two itd's to
be allocated. If the URB is scheduled to start in microframe 3 of
frame N then it will require both itds: one for microframes 3 - 7 of
frame N and one for microframes 0 - 2 of frame N+1. But if the URB
had been scheduled to start in microframe 0 then it would require only
the first itd, which could cover microframes 0 - 7 of frame N. The
second itd would be returned to the end of the free list.
The itd allocation routine initializes the entire structure to 0, so
the extra itd ends up on the free list with itd->frame set to 0
instead of a meaningful value. After a while the itd reaches the head
of the list, and occasionally this happens when ehci->now_frame is
equal to 0. Then, even though it would be okay to reuse this itd, the
driver thinks it must get another itd from the DMA pool.
For as long as the isochronous endpoint remains in use, this flaw in
the mechanism causes more and more itd's to be taken slowly from the
DMA pool. Since none are released back, the pool eventually becomes
exhausted.
This reuslts in memory allocation failures, which typically show up
during a long-running audio stream. Video might suffer the same
effect.
The fix is very simple. To prevent allocations from the pool when
they aren't needed, make sure that itd's sent back to the free list
prematurely have itd->frame set to an invalid value which can never be
equal to ehci->now_frame.
This should be applied to -stable kernels going back to 3.6.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a device attached to the roothub is suspended, the endpoint rings
are stopped. The host may generate a completion event with the
completion code set to 'Stopped' or 'Stopped Invalid' when the ring is
halted. The current xHCI code prints a warning in that case, which can
be really annoying if the USB device is coming into and out of suspend.
Remove the unnecessary warning.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Stephen Hemminger <stephen@networkplumber.org>
|
|
Use proper macro while extracting TRB transfer length from
Transfer event TRBs. Adding a macro EVENT_TRB_LEN (bits 0:23)
for the same, and use it instead of TRB_LEN (bits 0:16) in
case of event TRBs.
This patch should be backported to kernels as old as 2.6.31, that
contain the commit b10de142119a676552df3f0d2e3a9d647036c26a "USB: xhci:
Bulk transfer support". This patch will have issues applying to older
kernels.
Signed-off-by: Vivek gautam <gautam.vivek@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
This patch is to bind xhci root hub usb port with its acpi node.
The port num in the acpi table matches with the sequence in the xhci
extended capabilities table. So call usb_hcd_find_raw_port_number() to
transfer hub port num into raw port number which associates with
the sequence in the xhci extended capabilities table before binding.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
/home/b29397/work/code/git/linus/linux-2.6/drivers/usb/host/xhci-ring.c: In function ‘handle_port_status’:
/home/b29397/work/code/git/linus/linux-2.6/drivers/usb/host/xhci-ring.c:1580: warning: ‘hcd’ may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure waiting processes are woken on modem-status changes.
Currently processes are only woken on termios changes regardless of
whether the modem status has changed.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
When switching to tty ports, some lifetime assumptions were changed.
Specifically, close can now be called before the final tty reference is
dropped as part of hangup at device disconnect. Even with the ftdi
private-data refcounting this means that the port private data can be
freed while a process is sleeping on modem-status changes and thus
cannot be relied on to detect disconnects when woken up.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Also remove bogus test for private data pointer being NULL as it is
never assigned in the loop.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure the interface is not released before our serial device.
Note that drivers are still not allowed to access the interface in
any way that may interfere with another driver that may have gotten
bound to the same interface after disconnect returns.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing get_icount field to two-port driver.
The two-port driver was not updated when switching to the new icount
interface in commit 0bca1b913aff ("tty: Convert the USB drivers to the
new icount interface").
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove bogus disconnect test introduced by 95bef012e ("USB: more serial
drivers writing after disconnect") which prevented queued data from
being freed on disconnect.
The possible IO it was supposed to prevent is long gone.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unregister tty device in disconnect as is required by the USB stack.
By deferring unregistration to when the last tty reference is dropped,
the parent interface device can get unregistered before the child
resulting in broken hotplug events being generated when the tty is
finally closed:
KERNEL[2290.798128] remove /devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:3.1 (usb)
KERNEL[2290.804589] remove /devices/pci0000:00/0000:00:1d.7/usb2/2-1 (usb)
KERNEL[2294.554799] remove /2-1:3.1/tty/ttyACM0 (tty)
The driver must deal with tty callbacks after disconnect by checking the
disconnected flag. Specifically, further opens must be prevented and
this is already implemented.
Cc: stable <stable@vger.kernel.org>
Cc: Oliver Neukum <oneukum@suse.de>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
acm_probe() ignores errors in tty_port_register_device()
and leaves intfdata pointing to freed memory on alloc_fail7
error path. The patch fixes the both issues.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.9-rc4
udc-core learned that it shouldn't use invalid pointers
when unloading a gadget driver.
net2272 and net2280 got a fix for a regression caused by
the udc_start/udc_stop conversion.
We're defining a static inline no-op for otg_ulpi_create()
to prevent build errors when that driver isn't enabled.
FunctionFS got a fix for an off-by-one error when binding
and unbinding instances of FunctionFS.
MUSB learned that it shouldn't try to unmap buffers which
weren't previously mapped.
f_rndis got a fix for a possible NULL pointer dereference
in a debugging message code.
MUSB's DA8xx glue layer got a build fix due to a typo.
|
|
The Kconfig symbol USB_GADGET_NET2272_DMA was renamed to USB_NET2272_DMA
in commit 193ab2a6070039e7ee2b9b9bebea754a7c52fd1b ("usb: gadget: allow
multiple gadgets to be built"). That commit did not convert the only
occurrence of the corresponding Kconfig macro. Convert that macro now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch (as1670) fixes a regression caused by commit
6402c796d3b4205d3d7296157956c5100a05d7d6 (USB: EHCI: work around
silicon bug in Intel's EHCI controllers). The workaround goes through
two IAA cycles for each QH being unlinked. During the first cycle,
the QH is not added to the async_iaa list (because it isn't fully gone
from the hardware yet), which means that list will be empty.
Unfortunately, I forgot to update the IAA watchdog timer routine. It
thinks that an empty async_iaa list means the timer expiration was an
error, which isn't true any more. This problem didn't show up during
initial testing because the controllers being tested all had working
IAA interrupts. But not all controllers do, and when the watchdog
timer expires, the empty-list check prevents the second IAA cycle from
starting. As a result, URB unlinks never complete. The check needs
to be removed.
Among the symptoms of the regression are processes stuck in D wait
states and hangs during system shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Reported-by: Andreas Bombe <aeb@debian.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The udc_irq service runs the isr_tr_complete_handler which in turn
"nukes" the endpoints, including a call to rndis_response_complete,
if appropriate. If the rndis_msg_parser fails here, an error will
be printed using a dev_err call (through the ERROR() macro).
However, if the usb cable was just disconnected the device (cdev)
might not be available and will be null. Since the dev_err macro will
dereference the cdev pointer we get a null pointer exception.
Reviewed-by: Radovan Lekanovic <radovan.lekanovic@sonymobile.com>
Signed-off-by: Truls Bengtsson <truls.bengtsson@sonymobile.com>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch fixes an "off-by-one" bug found in
581791f (FunctionFS: enable multiple functions).
During gfs_bind/gfs_unbind the functionfs_bind/functionfs_unbind should be
called for every functionfs instance. With the "i" pre-decremented they
were not called for the zeroth instance.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@vger.kernel.org>
[ balbi@ti.com : added offending commit's subject ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch (as1667) removes an incorrect driver->unbind() call from
the net2280 driver. If startup fails, the UDC core takes care of
unbinding the gadget driver automatically; the controller driver
shouldn't do it too.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
