| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit ec961cf3241153e0f27d850f1bf0f172e7d27a21 ]
The hardware is capable of controlling any non-contiguous sequence of
LEDs specified in the DT using qcom,enabled-strings as u32
array, and this also follows from the DT-bindings documentation. The
numbers specified in this array represent indices of the LED strings
that are to be enabled and disabled.
Its value is appropriately used to setup and enable string modules, but
completely disregarded in the set_brightness paths which only iterate
over the number of strings linearly.
Take an example where only string 2 is enabled with
qcom,enabled_strings=<2>: this string is appropriately enabled but
subsequent brightness changes would have only touched the zero'th
brightness register because num_strings is 1 here. This is simply
addressed by looking up the string for this index in the enabled_strings
array just like the other codepaths that iterate over num_strings.
Likewise enabled_strings is now also used in the autodetection path for
consistent behaviour: when a list of strings is specified in DT only
those strings will be probed for autodetection, analogous to how the
number of strings that need to be probed is already bound by
qcom,num-strings. After all autodetection uses the set_brightness
helpers to set an initial value, which could otherwise end up changing
brightness on a different set of strings.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3")
Fixes: 03b2b5e86986 ("backlight: qcom-wled: Add support for WLED4 peripheral")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-10-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a139358548968b2ff308257b4fbeec7badcc3e1 ]
The kernel already provides appropriate primitives to perform endianness
conversion which should be used in favour of manual bit-wrangling.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-4-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b4b49602f9feca7b7a84eaa33ad9e666c8aa695 ]
The length of qcom,enabled-strings as property array is enough to
determine the number of strings to be enabled, without needing to set
qcom,num-strings to override the default number of strings when less
than the default (which is also the maximum) is provided in DT.
This also introduces an extra warning when qcom,num-strings is set,
denoting that it is not necessary to set both anymore. It is usually
more concise to set just qcom,num-length when a zero-based, contiguous
range of strings is needed (the majority of the cases), or to only set
qcom,enabled-strings when a specific set of indices is desired.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-6-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5ada78b26f935f8751852dffa24f6b545b1d2517 ]
When not specifying num-strings in the DT the default is used, but +1 is
added to it which turns WLED3 into 4 and WLED4/5 into 5 strings instead
of 3 and 4 respectively, causing out-of-bounds reads and register
read/writes. This +1 exists for a deficiency in the DT parsing code,
and is simply omitted entirely - solving this oob issue - by parsing the
property separately much like qcom,enabled-strings.
This also enables more stringent checks on the maximum value when
qcom,enabled-strings is provided in the DT, by parsing num-strings after
enabled-strings to allow it to check against (and in a subsequent patch
override) the length of enabled-strings: it is invalid to set
num-strings higher than that.
The DT currently utilizes it to get around an incorrect fixed read of
four elements from that array (has been addressed in a prior patch) by
setting a lower num-strings where desired.
Fixes: 93c64f1ea1e8 ("leds: add Qualcomm PM8941 WLED driver")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-By: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-5-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e29e24bdabfeddbf8b1a4ecac1af439a85150438 ]
of_property_read_u32_array takes the number of elements to read as last
argument. This does not always need to be 4 (sizeof(u32)) but should
instead be the size of the array in DT as read just above with
of_property_count_elems_of_size.
To not make such an error go unnoticed again the driver now bails
accordingly when of_property_read_u32_array returns an error.
Surprisingly the indentation of newlined arguments is lining up again
after prepending `rc = `.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-3-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c05b21ebc5bce3ecc78c2c71afd76d92c790a2ac ]
The strings passed in DT may possibly cause out-of-bounds register
accesses and should be validated before use.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-2-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d6e9cdff7fbb6bef3e5559596fab3eeffaf95ca ]
Currently, for WLED5, the FSC (Full scale current) setting is not
updated properly due to driver toggling the wrong register after
an FSC update.
On WLED5 we should only toggle the MOD_SYNC bit after a brightness
update. For an FSC update we need to toggle the SYNC bits instead.
Fix it by adopting the common wled3_sync_toggle() for WLED5 and
introducing new code to the brightness update path to compensate.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cdfd4c689e2a52c313b35ddfc1852ff274f91acb ]
WLED3_SINK_REG_SYNC is, as the name implies, a sink register offset.
Therefore, use the sink address as base instead of the ctrl address.
This fixes the sync toggle on wled4, which can be observed by the fact
that adjusting brightness now works.
It has no effect on wled3 because sink and ctrl base addresses are the
same. This allows adjusting the brightness without having to disable
then reenable the module.
Signed-off-by: Obeida Shamoun <oshmoun100@googlemail.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Introduce the backlight_get_brightness() helper in all
video/backlight/* drivers. This simplifies the code and align the
implementation of the update_status() operation across the different
backlight drivers.
Some of the drivers gains a little extra functionality by the change
as they now respect the fb_blank() ioctl.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fixes W=1 warnings:
drivers/video/backlight/qcom-wled.c:1294:34: warning: ‘wled4_string_cfg’ defined but not used [-Wunused-const-variable=]
1294 | static const struct wled_var_cfg wled4_string_cfg = {
| ^~~~~~~~~~~~~~~~
drivers/video/backlight/qcom-wled.c:1290:34: warning: ‘wled3_string_cfg’ defined but not used [-Wunused-const-variable=]
1290 | static const struct wled_var_cfg wled3_string_cfg = {
| ^~~~~~~~~~~~~~~~
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
PM8150L PMICs
PM8150L WLED supports the following:
- Two modulators and each sink can use any of the modulator
- Multiple CABC selection options from which one can be selected/enabled
- Multiple brightness width selection (12 bits to 15 bits)
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add wled_cabc_config, wled_sync_toggle, wled_ovp_fault_status
and wled_ovp_delay and wled_auto_detection_required callback
functions to prepare the driver for adding WLED5 support.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fixes coccicheck warning:
./drivers/video/backlight/qcom-wled.c:1104:5-15:
WARNING: Unsigned expression compared with zero: string_len > 0
The unsigned variable string_len is assigned a return value from the call
to of_property_count_elems_of_size(), which may return negative error code.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The auto string detection algorithm checks if the current WLED
sink configuration is valid. It tries enabling every sink and
checks if the OVP fault is observed. Based on this information
it detects and enables the valid sink configuration.
Auto calibration will be triggered when the OVP fault interrupts
are seen frequently thereby it tries to fix the sink configuration.
The auto-detection also kicks in when the connected LED string
of the display-backlight malfunctions (because of damage) and
requires the damaged string to be turned off to prevent the
complete panel and/or board from being damaged.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Handle the short circuit interrupt and check if the short circuit
interrupt is valid. Re-enable the module to check if it goes
away. Disable the module altogether if the short circuit event
persists.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
WLED4 peripheral is present on some PMICs like pmi8998 and
pm660l. It has a different register map and configurations
are also different. Add support for it.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Restructure the driver to add the support for new WLED
peripherals.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Rename the PM8941* references as WLED3 to make the driver
generic and have WLED support for other PMICs. Also rename
"i_boost_limit" and "i_limit" variables to "boost_i_limit"
and "string_i_limit" respectively to resemble the corresponding
register names.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
pm8941-wled.c driver is supporting the WLED peripheral
on pm8941. Rename it to qcom-wled.c so that it can support
WLED on multiple PMICs.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
